Home Log Out Menu

Test Results

Your Score

0%
(0/100)
Pass mark is 75%

Test Summary
Type: Sequential

Module: 04 (Electronic Fundamentals)

Sub-sections: 3b,

1. How does a Desynn pointer return to zero when power is removed?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: By hairspring

This question has been asked 1085 times with a success rate of 75 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

2. A resolver synchro output is obtained from a rotor with

Your Answer: (No Answer Given) INCORRECT

Correct Answer: two coils at 90° to each other

This question has been asked 3903 times with a success rate of 78 percent.

Comment/Reference: A resolver synchro has two coils at 90 degree

other.
Report problem
with question
Send your reference

A reduction from the optimum setting of the velocity feedback in a servo

3.
loop could cause

Your Answer: (No Answer Given) INCORRECT

Correct Answer: instability

This question has been asked 5586 times with a success rate of 67 percent.

See Pallett Automatic Flight Control pg 88.

Comment/Reference:

Report problem
with question

Send your reference

4. A command synchroscope indicates whether

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the slave engine is too fast or too slow

This question has been asked 6049 times with a success rate of 63 percent.

Aircraft Instruments, Principles and Applicatio

Pallett, Page 225
Comment/Reference:

Report problem
with question

Send your reference

5. Velocity feedback
Your Answer: (No Answer Given) INCORRECT

Correct Answer: opposes the demand input

This question has been asked 3556 times with a success rate of 72 percent.

Velocity feedback is anti-phase to the deman

opposes it.
Comment/Reference:

Report problem
with question

Send your reference

6. In a synchrotel, the

Your Answer: (No Answer Given) INCORRECT

Correct Answer: rotor coil and stator coil is fixed

This question has been asked 4878 times with a success rate of 67 percent.

Aircraft Instruments and Integrated Systems

149/150
Comment/Reference:

Report problem
with question

Send your reference

7. A two phase induction motor used in a servomechanism

Your Answer: (No Answer Given) INCORRECT

Correct Answer: is self starting under light loads

This question has been asked 5291 times with a success rate of 75 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

 8. Synchro capacitors are fitted

Your Answer: (No Answer Given) INCORRECT

Correct Answer: to improve sensitivity and accuracy

This question has been asked 4642 times with a success rate of 80 percent.

Synchro capacitors reduce stator current and

synchro system more accurate
Comment/Reference:

Report problem
with question

Send your reference

9. An inertia mass is held between springs. This is measuring

Your Answer: (No Answer Given) INCORRECT

Correct Answer: acceleration

This question has been asked 5418 times with a success rate of 90 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

10. An open loop system is one which has

Your Answer: (No Answer Given) INCORRECT

Correct Answer: no direct feedback loop

This question has been asked 3931 times with a success rate of 87 percent.

Open loop has no feedback.

Comment/Reference:

Report problem
with question

Send your reference

11. A differential synchro transmitter used for addition has

Your Answer: (No Answer Given) INCORRECT

the TDX R1, R3 and S1, S3 connections cross connected to

Correct Answer:
the TX

This question has been asked 4002 times with a success rate of 71 percent.

Aircraft Instruments and Integrated Systems.

Page 145
Comment/Reference:

Report problem
with question

Send your reference

12. A Desynn indicating system may be operated using

Your Answer: (No Answer Given) INCORRECT

Correct Answer: DC power only

This question has been asked 4285 times with a success rate of 79 percent.

Comment/Reference: Aircraft Instruments, Principles and Applicatio

Pallett, Page 225-226
Report problem
with question

Send your reference

 A servo system may include a brake, an automatic trim system is one
13.
example where a brake is used. The brake is

Your Answer: (No Answer Given) INCORRECT

applied when trimming is complete to prevent stabilizer

Correct Answer:
creep

This question has been asked 5333 times with a success rate of 71 percent.

The trim switch often consists of 2 separate s

is to release the brake, the other is to switch
Comment/Reference: motor.

Report problem
with question

Send your reference

14. A linear variometer is

Your Answer: (No Answer Given) INCORRECT

a special synchro giving ac output proportional to shaft

Correct Answer:
angle

This question has been asked 5231 times with a success rate of 70 percent.

Comment/Reference: A linear variometer is a device which gives an

voltage directly proportional to angle when co
Report problem gyro (for example)
with question

Send your reference

 15. The primary purpose of rate feedback in a positional servo system is to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: prevent excessive overshoot

This question has been asked 3630 times with a success rate of 75 percent.

Rate feedback is to prevent excessive oversh

oscillation.
Comment/Reference:

Report problem
with question

Send your reference

16. In a torque synchro system, the power supply is connected to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the rotor windings of both the transmitter and receiver

This question has been asked 3783 times with a success rate of 81 percent.

Pallett Aircraft Instruments and Integrated Sy

135. Aircraft Electricity and Electronics 5th Ed
Comment/Reference: Page 185/6

Report problem
with question

Send your reference

 17. A tacho-generator provides

Your Answer: (No Answer Given) INCORRECT

Correct Answer: velocity feedback

This question has been asked 5582 times with a success rate of 78 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

18. The term 'velocity lag' refers to a

Your Answer: (No Answer Given) INCORRECT

Correct Answer: position error

This question has been asked 4965 times with a success rate of 57 percent.

Velocity lag is the difference between the dem

and the load position. It is therefore a positio
Comment/Reference:

Report problem
with question

Send your reference

With power is removed what is used to return the indicator needle in a

19.
Desynn back to zero?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: A pull-off magnet

This question has been asked 1808 times with a success rate of 72 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

20. A servo system with transient negative velocity feedback

Your Answer: (No Answer Given) INCORRECT

Correct Answer: is damped with little velocity lag

This question has been asked 5329 times with a success rate of 63 percent.

Transient velocity feedback is a variable feedb

can be switched on when the system is about
overshoot (and anticipates the overshoot). Bu
Comment/Reference: be switched off when it is not required to redu
velocity lag.
Report problem
with question

Send your reference

21. A differential synchro motor consists of

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 3 windings at 120 degrees

This question has been asked 4278 times with a success rate of 87 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

 22. The output of a tachogenerator should be

Your Answer: (No Answer Given) INCORRECT

Correct Answer: sinusoidal

This question has been asked 5030 times with a success rate of 74 percent.

The output should be the same waveform as

i.e. sinusoidal.
Comment/Reference:

Report problem
with question

Send your reference

23. An LVDT output works on the principle of

Your Answer: (No Answer Given) INCORRECT

Correct Answer: inductance

This question has been asked 4016 times with a success rate of 79 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

The receiver rotor in a torque synchro system oscillates over an arc of

24.
approx 75 degrees. The probable cause is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: one stator line open circuit

This question has been asked 4729 times with a success rate of 67 percent.

Comment/Reference: A 'possible' symptom of a stator line open

Report problem
with question

Send your reference

What control system is used on an input that gives a controlled

25.
predetermined output?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: Closed Loop

This question has been asked 3467 times with a success rate of 78 percent.

Only a closed loop control system can give a

predetermined output.
Comment/Reference:

Report problem
with question

Send your reference

What is the output of the diagram below?

26.

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 60o clockwise

This question has been asked 3828 times with a success rate of 72 percent.

Comment/Reference: TX - TDX - TR (addition)

Aircraft Instruments and Integrated Systems
Report problem Page 145
with question

Send your reference

 27. A control surface position feedback signal is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: proportional to surface position

This question has been asked 4165 times with a success rate of 81 percent.

Position feedback is proportional to surface po

Meaning, as control surface deflection increas
Comment/Reference: the feedback.

Report problem
with question

Send your reference

28. An increase in negative feedback

Your Answer: (No Answer Given) INCORRECT

Correct Answer: decreases system sensitivity

This question has been asked 3963 times with a success rate of 57 percent.

Negative feedback (position and/or rate) incr

stability but makes the servo unresponsive to
Comment/Reference: changes.

Report problem
with question

Send your reference

 29. To check the output of a synchro stator it would be preferable to use

Your Answer: (No Answer Given) INCORRECT

Correct Answer: a Valve Voltmeter

This question has been asked 4727 times with a success rate of 65 percent.

Since the synchro stator output is a very low

high impedance multimeter would be used. S
not an answer provided the most sensitive of
Comment/Reference: the Valve Voltmeter.

Report problem
with question

Send your reference

In a transient velocity feedback circuit, the tachogenerator output is

30.
summated with the demand voltage

Your Answer: (No Answer Given) INCORRECT

Correct Answer: only when the load is speeding up or slowing down

This question has been asked 5075 times with a success rate of 63 percent.

Automatic Flight Control EHJ Pallett Page 91.

Comment/Reference:

Report problem
with question

Send your reference

31. Proportional, integral and derivative are all

Your Answer: (No Answer Given) INCORRECT

Correct Answer: methods of feedback control in servomechanisms

This question has been asked 2981 times with a success rate of 69 percent.
 (No Comment/Reference Available)
Comment/Reference:

Report problem
with question

Send your reference

32. The position feedback signal is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: in anti-phase with the demand signal

This question has been asked 3740 times with a success rate of 68 percent.

The position feedback must be anti-phase if i

oppose the demand input.
Comment/Reference:

Report problem
with question

Send your reference

The application of a 'stick-off' voltage to a control synchro servo

33.
system is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: to prevent alignment to a false null

This question has been asked 5157 times with a success rate of 66 percent.

Stick-off voltage is to prevent alignment to a

(i.e. 180 degrees out) when system is switch
Comment/Reference:

Report problem
with question

Send your reference

 34. On a torque synchro, the AC power supply is applied to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the rotors of both the transmitter and the receiver

This question has been asked 3977 times with a success rate of 70 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

35. A critically damped servo

Your Answer: (No Answer Given) INCORRECT

Correct Answer: will have no overshoots

This question has been asked 7046 times with a success rate of 70 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

36. A hysteresis servo motor is used in a servomechanism because

Your Answer: (No Answer Given) INCORRECT

Correct Answer: it has good starting characteristics

This question has been asked 5418 times with a success rate of 74 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question
Send your reference

In a speed control servo system (rate control), the purpose of the

37.
tachogenerator is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: to make it run at constant speed

This question has been asked 3813 times with a success rate of 64 percent.

The tachogenerator is to make the load run a

speed.
Comment/Reference:

Report problem
with question

Send your reference

The label on the synchro has a code 11CT6a . Which of the following is
38.
true about the synchro?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: The frequency of operation is 60Hz.

This question has been asked 5347 times with a success rate of 68 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

 39. Electrical power is supplied to a synchro rotor

Your Answer: (No Answer Given) INCORRECT

Correct Answer: through slip rings

This question has been asked 3661 times with a success rate of 76 percent.

Electrical power is connected to a synchro rot

slip rings.
Comment/Reference:

Report problem
with question

Send your reference

When a servo has reached its null and stopped, the velocity feedback
40.
is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: zero

This question has been asked 3526 times with a success rate of 84 percent.

Velocity feedback will stop when the load is a

Comment/Reference:

Report problem
with question

Send your reference

41. The negative effect of coulomb and viscous damping is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: heat

This question has been asked 5240 times with a success rate of 74 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

42. What device transfers one energy type to another?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: Transducer

This question has been asked 3400 times with a success rate of 84 percent.

The device that transfers one energy type to

called a transducer. Aircraft Electricity and Ele
Comment/Reference: Edition Eismin Page 171

Report problem
with question

Send your reference

43. In a control synchro system the power supply is connected to the

Your Answer: (No Answer Given) INCORRECT

Correct Answer: transmitter rotor and amplifier

This question has been asked 3987 times with a success rate of 55 percent.

Pallett Aircraft Instruments and Integrated Sy

141.
Comment/Reference:

Report problem
with question

Send your reference

 Angular displacement of the control coils with respect to the reference
44.
coils in a two phase induction motor are

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 90°, 270°

This question has been asked 4007 times with a success rate of 71 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

In a torque synchro that includes a differential synchro the power

45.
supply is connected to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the transmitter and receiver rotors only

This question has been asked 3856 times with a success rate of 77 percent.

See Pallett Aircraft Instruments and Integrate

pg 135.
Comment/Reference:

Report problem
with question

Send your reference

46. In a torque synchro system, current flows

Your Answer: (No Answer Given) INCORRECT

Correct Answer: when the rotors are misaligned

This question has been asked 3884 times with a success rate of 78 percent.

Comment/Reference: Aircraft Instruments and Integrated Systems.

 Page 137

Report problem
with question

Send your reference

47. Mechanical friction of a servomechanism will cause

Your Answer: (No Answer Given) INCORRECT

Correct Answer: increased damping

This question has been asked 6496 times with a success rate of 78 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

48. The reference phase to a synchro is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 400 Hz

This question has been asked 3892 times with a success rate of 79 percent.

Aircraft Electricity and Electronics, TK Eismin

Comment/Reference:

Report problem
with question

Send your reference

49. In an E and I signal generator at datum, the voltage on the secondary

 windings

Your Answer: (No Answer Given) INCORRECT

Correct Answer: are equal and opposite

This question has been asked 4822 times with a success rate of 80 percent.

Since an EandI bar transformer secondary wi

wound in series opposition, at datum the volt
Comment/Reference: secondary windings will be equal and opposit

Report problem
with question

Send your reference

The result of cross connecting two of the transmission leads in a

50. torque synchro system and then turning the rotor of the transmitter
60° clockwise would be

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the receiver would move 60° anticlockwise

This question has been asked 4970 times with a success rate of 80 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

51. An operational amplifier in an open-loop configuration is used for

Your Answer: (No Answer Given) INCORRECT

Correct Answer: comparator

This question has been asked 1125 times with a success rate of 68 percent.
 (No Comment/Reference Available)
Comment/Reference:

Report problem
with question

Send your reference

The frictional force in a servomechanism that is proportional to speed

52.
is called

Your Answer: (No Answer Given) INCORRECT

Correct Answer: viscous friction

This question has been asked 4427 times with a success rate of 70 percent.

Automatic Flight Control, 4th Edition, Pallett a

pg 86
Comment/Reference:

Report problem
with question

Send your reference

53. What type of feedback does an LVDT provide?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: Positional

This question has been asked 3821 times with a success rate of 77 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

 A low frequency sinusoidal input will cause a closed loop
54.
servomechanism load to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: move backwards and forwards at the input frequency

This question has been asked 5426 times with a success rate of 59 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

55. Critical damping of a servo is defined as

Your Answer: (No Answer Given) INCORRECT

Correct Answer: achieving the position with no overshoot

This question has been asked 987 times with a success rate of 65 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

56. The rotor of an AC tachogenerator

Your Answer: (No Answer Given) INCORRECT

Correct Answer: has a copper, brass or aluminium cylinder

This question has been asked 4825 times with a success rate of 71 percent.

Comment/Reference: An AC generator rotor is made from a diamag

material such as copper, brass or aluminium.
Report problem
with question
Send your reference

57. An increase in amplitude of a rate feedback signal will cause

Your Answer: (No Answer Given) INCORRECT

Correct Answer: reduced hunting

This question has been asked 3932 times with a success rate of 56 percent.

Rate feedback is to reduce overshoot and osc

(hunting), therefore, increasing the amplitude
Comment/Reference: the rate feedback will decrease tendency to h

Report problem
with question

Send your reference

In a toroidal resistance transmitter indicator system, the power supply

58.
is connected to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the brushes

This question has been asked 3839 times with a success rate of 63 percent.

A toroidal resistance indicator is better known

Desynn indicator.
Comment/Reference:

Report problem
with question

Send your reference

 The letter 'B' following the identification code on the case of a synchro
59.
denotes

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the modification status

This question has been asked 4799 times with a success rate of 71 percent.

https://www.analog.com/media/en/training-s
design-handbooks/synchro-resolver-conversio
Comment/Reference: Chapter1.pdf

Report problem
with question

Send your reference

60. A piezoelectric crystal is an example of

Your Answer: (No Answer Given) INCORRECT

Correct Answer: a Electro Acoustic Transducer

This question has been asked 3847 times with a success rate of 69 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

61. Loss of DC to a servo amplifier causes the motor to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: stop

This question has been asked 4972 times with a success rate of 83 percent.

Comment/Reference: Loss of DC to the servo-amplifier will cause th

 to stop working and the motor will therefore s

Report problem
with question

Send your reference

62. The power supply to a torque synchro system is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: AC

This question has been asked 3809 times with a success rate of 66 percent.

See Pallett Aircraft Instruments and Integrate

pg 135.
Comment/Reference:

Report problem
with question

Send your reference

63. A control synchro system pointer is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: motor driven

This question has been asked 5396 times with a success rate of 67 percent.

The receiver of a control synchro is effectively

speed synchronous motor
Comment/Reference:

Report problem
with question

Send your reference

 64. Differential synchros have

Your Answer: (No Answer Given) INCORRECT

Correct Answer: a transmitter and a receiver

This question has been asked 3836 times with a success rate of 89 percent.

See Pallett Aircraft Instruments and Integrate

pg 135.
Comment/Reference:

Report problem
with question

Send your reference

The control windings of a two phase servomotor is supplied with AC

65.
voltage of

Your Answer: (No Answer Given) INCORRECT

Correct Answer: variable amplitude, variable phase

This question has been asked 5197 times with a success rate of 72 percent.

The control windings are fed with variable am

but the amplitude can be positive (in phase)
Comment/Reference: (anti-phase).

Report problem
with question

Send your reference

If the rotor of the receiver in a torque synchro system was prevented

66.
from aligning with the transmitter rotor, then

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the receiver will overheat

This question has been asked 5206 times with a success rate of 71 percent.
 Current flows in the stator whenever the roto
correspondence.
Comment/Reference:

Report problem
with question

Send your reference

An AC servo demand can be converted to drive a DC motor by the

67.
introduction of a

Your Answer: (No Answer Given) INCORRECT

Correct Answer: demodulator

This question has been asked 5206 times with a success rate of 65 percent.

A demodulator differs from a rectifier in that

the phase of the AC input, and give an outpu
positive DC or negative DC accordingly. This
Comment/Reference: the DC motor in the correct direction.

Report problem
with question

Send your reference

In a synchro resolver, the stator coils are at what angle in relation to

68.
one another?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 90 degrees

This question has been asked 3564 times with a success rate of 89 percent.

Comment/Reference: In a synchro resolver the stator coils are 90 d

each other.";
Report problem
with question

Send your reference

 69. A D.C. signal converted to a phase sensitive A.C. is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: modulation

This question has been asked 5361 times with a success rate of 73 percent.

DC to phase sensitive AC = 'modulation'

Comment/Reference:

Report problem
with question

Send your reference

70. A two phase motor will stop when

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the control phase is zero

This question has been asked 5122 times with a success rate of 83 percent.

A two phase motor will stop when the control

zero (i.e. no output).
Comment/Reference:

Report problem
with question

Send your reference

71. An AC tachogenerator stator has

Your Answer: (No Answer Given) INCORRECT

Correct Answer: two windings 90° apart

This question has been asked 4201 times with a success rate of 55 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

72. Damping in a servomechanism is easier to apply if

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the mechanism is light and has low inertia

This question has been asked 5049 times with a success rate of 78 percent.

Overshoot and oscillation is greatest when th

is heavy and has a high inertia.
Comment/Reference:

Report problem
with question

Send your reference

73. To reduce overshoot errors in a synchro

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the system will have velocity feedback

This question has been asked 3872 times with a success rate of 63 percent.

Comment/Reference: Velocity feedback is used to reduce overshoot

oscillations.
Report problem
with question

Send your reference

 The result of reversing the rotor connections to the receiver of a
74.
torque synchro system is that the rotor position

Your Answer: (No Answer Given) INCORRECT

Correct Answer: is changed by 180°

This question has been asked 5072 times with a success rate of 76 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

75. In practice, servo systems are designed to be

Your Answer: (No Answer Given) INCORRECT

Correct Answer: slightly underdamped

This question has been asked 4970 times with a success rate of 64 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

On a servo system using a control synchro, if the feedback became

76.
disconnected the output would
Your Answer: (No Answer Given) INCORRECT

Correct Answer: run to a limit and then stop

This question has been asked 3849 times with a success rate of 65 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

77. The output of a resolver synchro is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: a function of the rotor position and excitation voltage

This question has been asked 3699 times with a success rate of 64 percent.

The output of a resolver synchro is angular po

voltage to represent the distance.
Comment/Reference:

Report problem
with question

Send your reference

78. In a desynn control system, the stator is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: single phase

This question has been asked 3944 times with a success rate of 63 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

 79. On a torque synchro

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the transmitter and the receiver both need AC supply

This question has been asked 3783 times with a success rate of 84 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

80. In general the accuracy of a synchro system increases if the

Your Answer: (No Answer Given) INCORRECT

Correct Answer: stator current is low

This question has been asked 5094 times with a success rate of 60 percent.

The synchro system is only accurate when th

are in correspondence. At this time the stator
Comment/Reference: zero.

Report problem
with question

Send your reference

81. The output of a control transformer is made

Your Answer: (No Answer Given) INCORRECT

phase and amplitude sensitive by direction and magnitude of

Correct Answer:
the transmitter rotor movement respectively

This question has been asked 4731 times with a success rate of 63 percent.

Automatic Flight Control, 4th Edition, Pallett a

Pg 134
Comment/Reference:

Report problem
with question

Send your reference

82. Synchro capacitors are connected into synchro systems to

Your Answer: (No Answer Given) INCORRECT

Correct Answer: increase the accuracy of the control synchro

This question has been asked 4840 times with a success rate of 65 percent.

Synchro capacitors increase the accuracy of t

system
Comment/Reference:

Report problem
with question

Send your reference

83. What power is required for a desynn indicator system?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: DC

This question has been asked 3822 times with a success rate of 78 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question
Send your reference

84. The rotor of a torque synchro indicator is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: supplied with an excitation voltage

This question has been asked 3577 times with a success rate of 72 percent.

The excitation voltage is that necessary to ma

rotor
Comment/Reference:

Report problem
with question

Send your reference

85. A resolver has

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 2 coils on the rotor and 2 coils on the stator

This question has been asked 4091 times with a success rate of 75 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

86. If two of the stator leads are cross connected in a control synchro
system, a 25° clockwise rotation of the input rotor would result in the
 output rotor

Your Answer: (No Answer Given) INCORRECT

Correct Answer: moving 25° anticlockwise

This question has been asked 5079 times with a success rate of 84 percent.

Cross connecting two stator leads of a contro

make the magnetic field in the receiver rotate
Comment/Reference: opposite direction as the transmitter.

Report problem
with question

Send your reference

87. In a synchro system, if two stator lines are crossed the receiver will

Your Answer: (No Answer Given) INCORRECT

Correct Answer: reverse direction

This question has been asked 5103 times with a success rate of 62 percent.

If two stator lines are crossed the receiver wi

direction.
Comment/Reference:

Report problem
with question

Send your reference

88. Optimum damping of a servo is defined as

Your Answer: (No Answer Given) INCORRECT

Correct Answer: achieving the position with one overshoot

This question has been asked 988 times with a success rate of 62 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

89. In a sine resolver, the stator windings are

Your Answer: (No Answer Given) INCORRECT

Correct Answer: 90 degrees to each other

This question has been asked 3965 times with a success rate of 80 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

90. The rotor of a desynn indicator is

Your Answer: (No Answer Given) INCORRECT

Correct Answer: a permanent magnet

This question has been asked 3682 times with a success rate of 79 percent.

Aircraft Instruments, Principles and Applicatio

Pallett, Page 226
Comment/Reference:

Report problem
with question

Send your reference

The label on the synchro has a code 32TR4b. Which of the following is
91.
true about the synchro?
Your Answer: (No Answer Given) INCORRECT

Correct Answer: It is a torque receiver synchro.

This question has been asked 5339 times with a success rate of 84 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

92. In a d.c. generator what is used for collecting current?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: A commutator

This question has been asked 2080 times with a success rate of 68 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

93. The rotor of an AC rate feedback generator

Your Answer: (No Answer Given) INCORRECT

Correct Answer: is a copper or aluminium cylinder

This question has been asked 5288 times with a success rate of 72 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question

Send your reference

 94. With a constant input to a speed control servo, the servo motor

Your Answer: (No Answer Given) INCORRECT

Correct Answer: moves at a constant speed

This question has been asked 4867 times with a success rate of 85 percent.

A speed control servo moves the load (e.g. a

at constant speed.
Comment/Reference:

Report problem
with question

Send your reference

In a velocity feedback damping system the net input to the amplifier is

95.
the voltage proportional to

Your Answer: (No Answer Given) INCORRECT

the error signal minus the voltage proportional to speed of

Correct Answer:
the output shaft.

This question has been asked 5560 times with a success rate of 54 percent.

Automatic Flight Control, 4th Edition, Pallett a

pg 84
Comment/Reference:

Report problem
with question

Send your reference

 96. In a stabilised Control Synchro system

Your Answer: (No Answer Given) INCORRECT

Correct Answer: the CT rotor leads the CX rotor by 90 degrees

This question has been asked 1029 times with a success rate of 59 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

97. What does the Desynn indicator rotor consist of?

Your Answer: (No Answer Given) INCORRECT

Correct Answer: Permanent Magnet

This question has been asked 3310 times with a success rate of 81 percent.

(No Comment/Reference Available)

Comment/Reference:

Report problem
with question

Send your reference

98. A tachogenerator is usually used for

Your Answer: (No Answer Given) INCORRECT

Correct Answer: rate feedback

This question has been asked 3986 times with a success rate of 79 percent.

Comment/Reference: (No Comment/Reference Available)

Report problem
with question
 Send your reference

99. A differential synchro rotor has

Your Answer: (No Answer Given) INCORRECT

Correct Answer: three windings

This question has been asked 4123 times with a success rate of 81 percent.

See Pallett Aircraft Instruments and Integrate

pg 135.
Comment/Reference:

Report problem
with question

Send your reference

100. A rate control servo system with a steady input voltage will give

Your Answer: (No Answer Given) INCORRECT

Correct Answer: constant speed

This question has been asked 3777 times with a success rate of 87 percent.

A rate control system with a steady input volt

a constant speed output
Comment/Reference:

Report problem
with question

Send your reference

Buy the TTS Study Notes for Module 4

High quality study notes for Module 4 from Total Training Support. Available in printed hard-copy or ebook
format.

Module 4 Study Notes - Printed Hard Copy

Delivered to your home, anywhere, worldwide.

Module 4 Study Notes - Ebook Format

Instant access on your PC, tablet or phone.

Privacy Policy
Terms and Conditions
Equal Opportunities and Diversity
Quality Policy
Contact

Copyright © 2024 Total Training Support. All Rights Reserved.

LOADING...