Home Log Out Menu
Test Results
Your Score
0%
(0/100)
Pass mark is 75%
Test Summary
Type: Sequential
Module: 04 (Electronic Fundamentals)
Sub-sections: 3b,
1. In a control synchro the stator current ceases to flow when
Your Answer: (No Answer Given) INCORRECT
Correct Answer: when power is removed
This question has been asked 5163 times with a success rate of 64 percent.
In a control synchro, the stator is supplied wi
all times, whatever the transformer rotor pos
Comment/Reference:
Report problem
with question
Send your reference
2. The cogging effect in synchros is rectified by
Your Answer: (No Answer Given) INCORRECT
Correct Answer: skewing the rotor
This question has been asked 4832 times with a success rate of 75 percent.
Comment/Reference: The cogging effect in a synchro is prevented b
(or twisting) the rotor.
Report problem
with question
Send your reference
3. In a control synchro the stator current ceases to flow when the
Your Answer: (No Answer Given) INCORRECT
Correct Answer: power is removed
This question has been asked 3758 times with a success rate of 71 percent.
In a control synchro current flows in the stato
times, regardless of the position of the transf
Comment/Reference:
Report problem
with question
Send your reference
4. The output of a tachogenerator should be
Your Answer: (No Answer Given) INCORRECT
Correct Answer: sinusoidal
This question has been asked 5031 times with a success rate of 74 percent.
The output should be the same waveform as
i.e. sinusoidal.
Comment/Reference:
Report problem
with question
Send your reference
5. A tacho-generator provides
Your Answer: (No Answer Given) INCORRECT
Correct Answer: velocity feedback
This question has been asked 5583 times with a success rate of 78 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
6. When a servomotor overshoots after a step input and oscillates it is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: under damped
This question has been asked 5048 times with a success rate of 79 percent.
Automatic Flight Control, 4th Edition, Pallett a
page 87
Comment/Reference:
Report problem
with question
Send your reference
7. A basic CX synchro has
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 3 stator windings and 1 rotor winding
This question has been asked 4513 times with a success rate of 64 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
If the electrical connections to the feedback generator in a control
8.
synchro system were disconnected, the
Your Answer: (No Answer Given) INCORRECT
Correct Answer: system would tend to oscillate
This question has been asked 5054 times with a success rate of 77 percent.
Feedback from the tachogenerator prevents o
and overshoot, so disconnecting the feedback
Comment/Reference: the load to overshoot and oscillate.
Report problem
with question
Send your reference
The control windings of a two phase servomotor is supplied with AC
9.
voltage of
Your Answer: (No Answer Given) INCORRECT
Correct Answer: variable amplitude, variable phase
This question has been asked 5198 times with a success rate of 72 percent.
Comment/Reference: The control windings are fed with variable am
but the amplitude can be positive (in phase)
Report problem (anti-phase).
with question
Send your reference
If, in a servo system, the amplitude from the feedback system is below
10.
normal, the servo will
Your Answer: (No Answer Given) INCORRECT
Correct Answer: oscillate
This question has been asked 5037 times with a success rate of 65 percent.
The feedback system is designed to prevent o
and oscillation (hunting)
Comment/Reference:
Report problem
with question
Send your reference
11. An increase in velocity feedback will
Your Answer: (No Answer Given) INCORRECT
Correct Answer: decrease the speed the load moves
This question has been asked 3967 times with a success rate of 66 percent.
Velocity feedback opposes demand input ther
reduces thew speed the load moves.
Comment/Reference:
Report problem
with question
Send your reference
A low frequency sinusoidal input will cause a closed loop
12.
servomechanism load to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: move backwards and forwards at the input frequency
This question has been asked 5427 times with a success rate of 59 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
13. Mechanical friction of a servomechanism will cause
Your Answer: (No Answer Given) INCORRECT
Correct Answer: increased damping
This question has been asked 6497 times with a success rate of 78 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
14. A servo loop that oscillates about a null point is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: under damped
This question has been asked 5485 times with a success rate of 78 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
15. The reference phase to a synchro is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 400 Hz
This question has been asked 3893 times with a success rate of 79 percent.
Aircraft Electricity and Electronics, TK Eismin
Comment/Reference:
Report problem
with question
Send your reference
16. What type of feedback does an LVDT provide?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Positional
This question has been asked 3822 times with a success rate of 77 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
17. In a desynn control system, the stator is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: single phase
This question has been asked 3945 times with a success rate of 62 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
In a control servo transmitter, when is there maximum coupling
18.
between rotor and stator coils?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: When rotor and stator coils are parallel
This question has been asked 1710 times with a success rate of 60 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
19. In a Desynn indicator system, where is power supplied to?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Transmitter only
This question has been asked 3682 times with a success rate of 64 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
20. A differential synchro rotor consists of
Your Answer: (No Answer Given) INCORRECT
Correct Answer: three windings at 120° apart
This question has been asked 4011 times with a success rate of 80 percent.
Pallett Aircraft Instruments and Integrated Sy
143.
Comment/Reference:
Report problem
with question
Send your reference
In a velocity feedback damping system the net input to the amplifier is
21.
the voltage proportional to
Your Answer: (No Answer Given) INCORRECT
the error signal minus the voltage proportional to speed of
Correct Answer:
the output shaft.
This question has been asked 5561 times with a success rate of 54 percent.
Automatic Flight Control, 4th Edition, Pallett a
pg 84
Comment/Reference:
Report problem
with question
Send your reference
In an E and I signal generator at datum, the voltage on the secondary
22.
windings
Your Answer: (No Answer Given) INCORRECT
Correct Answer: are equal and opposite
This question has been asked 4823 times with a success rate of 80 percent.
Since an EandI bar transformer secondary wi
wound in series opposition, at datum the volt
Comment/Reference: secondary windings will be equal and opposit
Report problem
with question
Send your reference
23. The stator output voltages from a synchro resolver are
Your Answer: (No Answer Given) INCORRECT
Correct Answer: AC single phase
This question has been asked 3525 times with a success rate of 69 percent.
AC single phase from each winding
Comment/Reference:
Report problem
with question
Send your reference
24. In a rate servo (speed control) the signal into the servo amplifier is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: input voltage minus tachogenerator output
This question has been asked 3730 times with a success rate of 71 percent.
Comment/Reference: In a rate servo the input voltage makes the lo
and the tachogenerator output (which is nega
feedback) prevents it rotating too fast.
Report problem
with question
Send your reference
A linear variable differential transformer is used to measure position
25.
feedback where
Your Answer: (No Answer Given) INCORRECT
an output whose phase is related to direction of movement
Correct Answer:
and amplitude linear over a wide range
This question has been asked 5226 times with a success rate of 79 percent.
An LVDT measures position and provides a di
phase according to the direction of movemen
Comment/Reference:
Report problem
with question
Send your reference
26. Synchro capacitors are fitted
Your Answer: (No Answer Given) INCORRECT
Correct Answer: to improve sensitivity and accuracy
This question has been asked 4643 times with a success rate of 80 percent.
Comment/Reference: Synchro capacitors reduce stator current and
synchro system more accurate
Report problem
with question
Send your reference
27. To reduce overshoot errors in a synchro
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the system will have velocity feedback
This question has been asked 3873 times with a success rate of 63 percent.
Velocity feedback is used to reduce overshoot
oscillations.
Comment/Reference:
Report problem
with question
Send your reference
The phase difference between the supplies of a two phase induction
28.
motor is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 90°
This question has been asked 5244 times with a success rate of 73 percent.
The phase difference of the two phases applie
induction motor is 90°.
Comment/Reference:
Report problem
with question
Send your reference
29. The rotor of an AC rate feedback generator
Your Answer: (No Answer Given) INCORRECT
Correct Answer: is a copper or aluminium cylinder
This question has been asked 5289 times with a success rate of 72 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
30. Torque synchro receiver bearing friction will cause
Your Answer: (No Answer Given) INCORRECT
Correct Answer: misalignment
This question has been asked 4688 times with a success rate of 68 percent.
Bearing friction will cause the delicate rotor to
the desired position
Comment/Reference:
Report problem
with question
Send your reference
Angular displacement of the control coils with respect to the reference
31.
coils in a two phase induction motor are
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 90°, 270°
This question has been asked 4008 times with a success rate of 71 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
32. Optimum damping of a servo is defined as
Your Answer: (No Answer Given) INCORRECT
Correct Answer: achieving the position with one overshoot
This question has been asked 989 times with a success rate of 61 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
33. The rotor of a torque synchro indicator is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: supplied with an excitation voltage
This question has been asked 3578 times with a success rate of 72 percent.
The excitation voltage is that necessary to ma
rotor
Comment/Reference:
Report problem
with question
Send your reference
34. A hysteresis servo motor is used in a servomechanism because
Your Answer: (No Answer Given) INCORRECT
Correct Answer: it has good starting characteristics
This question has been asked 5419 times with a success rate of 74 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
35. A closed loop servomechanism
Your Answer: (No Answer Given) INCORRECT
Correct Answer: can have either position or velocity feedback
This question has been asked 4391 times with a success rate of 77 percent.
A closed loop servomechanism can have eithe
feedback or velocity feedback or both.
Comment/Reference:
Report problem
with question
Send your reference
36. Damping in a servomechanism is easier to apply if
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the mechanism is light and has low inertia
This question has been asked 5050 times with a success rate of 78 percent.
Comment/Reference: Overshoot and oscillation is greatest when th
is heavy and has a high inertia.
Report problem
with question
Send your reference
37. In a d.c. generator what is used for collecting current?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: A commutator
This question has been asked 2081 times with a success rate of 68 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
38. What does the Desynn indicator rotor consist of?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Permanent Magnet
This question has been asked 3311 times with a success rate of 81 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
39. A servo system with transient negative velocity feedback
Your Answer: (No Answer Given) INCORRECT
Correct Answer: is damped with little velocity lag
This question has been asked 5330 times with a success rate of 63 percent.
Transient velocity feedback is a variable feedb
can be switched on when the system is about
overshoot (and anticipates the overshoot). Bu
Comment/Reference: be switched off when it is not required to redu
velocity lag.
Report problem
with question
Send your reference
With power is removed what is used to return the indicator needle in a
40.
Desynn back to zero?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: A pull-off magnet
This question has been asked 1809 times with a success rate of 72 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
41. How does a Desynn pointer return to zero when power is removed?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: By hairspring
This question has been asked 1086 times with a success rate of 75 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
42. 'Deadband' in a servomechanism is the
Your Answer: (No Answer Given) INCORRECT
minimum input voltage level required to make the
Correct Answer:
servomechanism produce an output
This question has been asked 2260 times with a success rate of 71 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
43. The output from a control transformer is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: AC voltage
This question has been asked 3536 times with a success rate of 76 percent.
The control transformer provides AC voltage i
to the error signal
Comment/Reference:
Report problem
with question
Send your reference
44. The output of a resolver synchro is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: a function of the rotor position and excitation voltage
This question has been asked 3700 times with a success rate of 64 percent.
The output of a resolver synchro is angular po
voltage to represent the distance.
Comment/Reference:
Report problem
with question
Send your reference
The label on the synchro has a code 32TR4b. Which of the following is
45.
true about the synchro?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: It is a torque receiver synchro.
This question has been asked 5340 times with a success rate of 84 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
46. An open loop system is one which has
Your Answer: (No Answer Given) INCORRECT
Correct Answer: no direct feedback loop
This question has been asked 3932 times with a success rate of 87 percent.
Comment/Reference: Open loop has no feedback.
Report problem
with question
Send your reference
47. A differential synchro
Your Answer: (No Answer Given) INCORRECT
Correct Answer: can be used as either a transmitter or a receiver
This question has been asked 4208 times with a success rate of 86 percent.
The TDX is a transmitter, the TDR is a receive
Comment/Reference:
Report problem
with question
Send your reference
The receiver rotor in a torque synchro system oscillates over an arc of
48.
approx 75 degrees. The probable cause is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: one stator line open circuit
This question has been asked 4730 times with a success rate of 66 percent.
A 'possible' symptom of a stator line open
Comment/Reference:
Report problem
with question
Send your reference
49. What device transfers one energy type to another?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Transducer
This question has been asked 3401 times with a success rate of 84 percent.
The device that transfers one energy type to
called a transducer. Aircraft Electricity and Ele
Comment/Reference: Edition Eismin Page 171
Report problem
with question
Send your reference
A servo system may include a brake, an automatic trim system is one
50.
example where a brake is used. The brake is
Your Answer: (No Answer Given) INCORRECT
applied when trimming is complete to prevent stabilizer
Correct Answer:
creep
This question has been asked 5334 times with a success rate of 71 percent.
The trim switch often consists of 2 separate s
is to release the brake, the other is to switch
Comment/Reference: motor.
Report problem
with question
Send your reference
51. A critically damped servo
Your Answer: (No Answer Given) INCORRECT
Correct Answer: will have no overshoots
This question has been asked 7047 times with a success rate of 70 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
A transmitter that varies its output by using a variable dielectric
52.
material is a
Your Answer: (No Answer Given) INCORRECT
Correct Answer: capacitance transmitter
This question has been asked 1999 times with a success rate of 79 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
53. The rotor of an autosyn position indicating system is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: an electromagnet
This question has been asked 3632 times with a success rate of 60 percent.
Aircarft Electricity & Electronics 5th edition Ei
353
Comment/Reference:
Report problem
with question
Send your reference
54. An inertia mass is held between springs. This is measuring
Your Answer: (No Answer Given) INCORRECT
Correct Answer: acceleration
This question has been asked 5419 times with a success rate of 90 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
55. A synchro transformer is used to
Your Answer: (No Answer Given) INCORRECT
derive an error voltage from a synchro transmitter signal
Correct Answer:
and a shaft position
This question has been asked 4051 times with a success rate of 74 percent.
Pallett Automatic Flight Control pg 135.
Comment/Reference:
Report problem
with question
Send your reference
56. In a tachogenerator the output voltage is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: directly proportional to the speed
This question has been asked 3606 times with a success rate of 84 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
57. A differential synchro has
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 3 phase stator, 3 phase rotor
This question has been asked 4276 times with a success rate of 75 percent.
Aircraft instruments and Integrated Systems,
Page 142
Comment/Reference:
Report problem
with question
Send your reference
58. On a torque synchro
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the transmitter and the receiver both need AC supply
This question has been asked 3784 times with a success rate of 84 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
59. The power supply to a torque synchro system is connected to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the transmitter and receiver rotors
This question has been asked 3693 times with a success rate of 84 percent.
See Pallett Aircraft |Instruments and Integrat
pg 135.
Comment/Reference:
Report problem
with question
Send your reference
60. A servomechanism must have
Your Answer: (No Answer Given) INCORRECT
Correct Answer: either position or speed control
This question has been asked 1990 times with a success rate of 83 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
The result of cross connecting two of the transmission leads in a
61. torque synchro system and then turning the rotor of the transmitter
60° clockwise would be
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the receiver would move 60° anticlockwise
This question has been asked 4971 times with a success rate of 80 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
62. A resolver synchro output is obtained from a rotor with
Your Answer: (No Answer Given) INCORRECT
Correct Answer: two coils at 90° to each other
This question has been asked 3904 times with a success rate of 78 percent.
A resolver synchro has two coils at 90 degree
other.
Comment/Reference:
Report problem
with question
Send your reference
The result of reversing the rotor connections to the receiver of a
63.
torque synchro system is that the rotor position
Your Answer: (No Answer Given) INCORRECT
Correct Answer: is changed by 180°
This question has been asked 5073 times with a success rate of 76 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
64. Positional feedback can be obtained from a
Your Answer: (No Answer Given) INCORRECT
Correct Answer: synchro
This question has been asked 3647 times with a success rate of 72 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
65. The rotor of a desynn indicator is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: a permanent magnet
This question has been asked 3683 times with a success rate of 79 percent.
Aircraft Instruments, Principles and Applicatio
Pallett, Page 226
Comment/Reference:
Report problem
with question
Send your reference
66. Position feedback is used to
Your Answer: (No Answer Given) INCORRECT
ensure control surface moves to the demanded position by
Correct Answer:
the controls
This question has been asked 3487 times with a success rate of 79 percent.
Comment/Reference: Position feedback is to ensure control surface
(and stops at) the demanded position by the
Report problem
with question
Send your reference
If two of the stator leads are cross connected in a control synchro
67. system, a 25° clockwise rotation of the input rotor would result in the
output rotor
Your Answer: (No Answer Given) INCORRECT
Correct Answer: moving 25° anticlockwise
This question has been asked 5080 times with a success rate of 84 percent.
Cross connecting two stator leads of a contro
make the magnetic field in the receiver rotate
Comment/Reference: opposite direction as the transmitter.
Report problem
with question
Send your reference
The purpose of synchro capacitors in a differential synchro
68.
transmission system
Your Answer: (No Answer Given) INCORRECT
Correct Answer: to reduce stator current
This question has been asked 4774 times with a success rate of 61 percent.
Comment/Reference: Synchro capacitors reduce stator current and
synchro system more accurate
Report problem
with question
Send your reference
69. What does a resolver do?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Resolves a position into sine and cosine components
This question has been asked 3481 times with a success rate of 70 percent.
A resolver converts a position from polar coor
cartesian coordinates, and/or vice versa
Comment/Reference:
Report problem
with question
Send your reference
70. The power supply to a torque synchro system is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: AC
This question has been asked 3810 times with a success rate of 66 percent.
See Pallett Aircraft Instruments and Integrate
pg 135.
Comment/Reference:
Report problem
with question
Send your reference
71. When is maximum voltage induced into the rotor of a control synchro
transformer?
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 0 degrees
This question has been asked 4784 times with a success rate of 64 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
72. To increase the output of a servo amplifier, it is necessary to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: reduce the tacho feedback
This question has been asked 3764 times with a success rate of 61 percent.
Tachogenerator feedback opposes the error s
thus reduces amplifier output.
Comment/Reference:
Report problem
with question
Send your reference
The letter 'B' following the identification code on the case of a synchro
73.
denotes
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the modification status
This question has been asked 4800 times with a success rate of 71 percent.
Comment/Reference: https://www.analog.com/media/en/training-s
design-handbooks/synchro-resolver-conversio
Chapter1.pdf
Report problem
with question
Send your reference
74. In a torque synchro system, the power supply is connected to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the rotor windings of both the transmitter and receiver
This question has been asked 3784 times with a success rate of 81 percent.
Pallett Aircraft Instruments and Integrated Sy
135. Aircraft Electricity and Electronics 5th Ed
Comment/Reference: Page 185/6
Report problem
with question
Send your reference
With the pick-off system shown, movement of the wiper P will produce
what output?
75.
Your Answer: (No Answer Given) INCORRECT
Correct Answer: Variable amplitude, variable polarity
This question has been asked 5812 times with a success rate of 69 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
76. An aircraft control servo system has 'follow-up'. This means that it is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: closed loop
This question has been asked 2022 times with a success rate of 87 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
77. When resolving a Cartesian input to a Polar output
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the inputs are two voltages
This question has been asked 3569 times with a success rate of 57 percent.
Cartesian inputs are the X and Y coordinates
represented by two voltages. The outputs are
Comment/Reference: by a voltage and an angular position.
Report problem
with question
Send your reference
78. A command synchroscope indicates whether
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the slave engine is too fast or too slow
This question has been asked 6050 times with a success rate of 63 percent.
Aircraft Instruments, Principles and Applicatio
Pallett, Page 225
Comment/Reference:
Report problem
with question
Send your reference
79. A control surface position feedback signal is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: proportional to surface position
This question has been asked 4166 times with a success rate of 81 percent.
Position feedback is proportional to surface po
Meaning, as control surface deflection increas
Comment/Reference: the feedback.
Report problem
with question
Send your reference
The application of a 'stick-off' voltage to a control synchro servo
80.
system is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: to prevent alignment to a false null
This question has been asked 5158 times with a success rate of 66 percent.
Stick-off voltage is to prevent alignment to a
(i.e. 180 degrees out) when system is switch
Comment/Reference:
Report problem
with question
Send your reference
On a servo system using a control synchro, if the feedback became
81.
disconnected the output would
Your Answer: (No Answer Given) INCORRECT
Correct Answer: run to a limit and then stop
This question has been asked 3850 times with a success rate of 65 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
82. A two phase induction motor used in a servomechanism
Your Answer: (No Answer Given) INCORRECT
Correct Answer: is self starting under light loads
This question has been asked 5292 times with a success rate of 75 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
83. If the rotor of a control synchro sticks
Your Answer: (No Answer Given) INCORRECT
Correct Answer: high current will flow
This question has been asked 5248 times with a success rate of 72 percent.
High current flows in the stators whenever th
not in correspondence.
Comment/Reference:
Report problem
with question
Send your reference
84. An operational amplifier in an open-loop configuration is used for
Your Answer: (No Answer Given) INCORRECT
Correct Answer: comparator
This question has been asked 1126 times with a success rate of 68 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
85. The difference between an open and closed loop is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: feedback
This question has been asked 3509 times with a success rate of 88 percent.
Comment/Reference: (No Comment/Reference Available)
Report problem
with question
Send your reference
86. The primary purpose of rate feedback in a positional servo system is to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: prevent excessive overshoot
This question has been asked 3631 times with a success rate of 75 percent.
Rate feedback is to prevent excessive oversh
oscillation.
Comment/Reference:
Report problem
with question
Send your reference
87. Torque synchro systems are normally used when the
Your Answer: (No Answer Given) INCORRECT
Correct Answer: mechanical load is low
This question has been asked 3506 times with a success rate of 69 percent.
Torque synchros are used for indication only,
the load is low.
Comment/Reference:
Report problem
with question
Send your reference
88. Describe how the windings are connected when using a resolver
synchro to convert from Cartesian to polar co-ordinates.
Your Answer: (No Answer Given) INCORRECT
The inputs are connected to the S1/S2 and S3/S4. R1/R2
Correct Answer: are connected to the discriminator and servomotor. R3/R4
provides an output voltage
This question has been asked 4010 times with a success rate of 68 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
89. When the rotor of an AC tachogenerator is stationary, the rotor has
Your Answer: (No Answer Given) INCORRECT
Correct Answer: low circulating currents
This question has been asked 3585 times with a success rate of 64 percent.
A small amount of residual voltage exists on t
winding of an AC tachogenerator when it is st
Comment/Reference:
Report problem
with question
Send your reference
In a torque synchro that includes a differential synchro the power
90.
supply is connected to
Your Answer: (No Answer Given) INCORRECT
Correct Answer: the transmitter and receiver rotors only
This question has been asked 3857 times with a success rate of 77 percent.
See Pallett Aircraft Instruments and Integrate
pg 135.
Comment/Reference:
Report problem
with question
Send your reference
91. Increasing velocity feedback from optimum will give
Your Answer: (No Answer Given) INCORRECT
Correct Answer: sluggish performance
This question has been asked 3564 times with a success rate of 75 percent.
Velocity feedback is subtracted from the erro
reduce the rate of the output.
Comment/Reference:
Report problem
with question
Send your reference
If velocity feedback in a servo system is above optimum, this will
92.
cause
Your Answer: (No Answer Given) INCORRECT
Correct Answer: sluggish operation
This question has been asked 3779 times with a success rate of 67 percent.
Velocity feedback slows down the operation o
Comment/Reference:
Report problem
with question
Send your reference
93. An LVDT output works on the principle of
Your Answer: (No Answer Given) INCORRECT
Correct Answer: inductance
This question has been asked 4017 times with a success rate of 79 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
94. An increase in negative feedback
Your Answer: (No Answer Given) INCORRECT
Correct Answer: decreases system sensitivity
This question has been asked 3964 times with a success rate of 57 percent.
Negative feedback (position and/or rate) incr
stability but makes the servo unresponsive to
Comment/Reference: changes.
Report problem
with question
Send your reference
95. A tachogenerator output is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: variable voltage, constant frequency
This question has been asked 5372 times with a success rate of 58 percent.
Comment/Reference: A tachogenerator output is the same frequenc
input (i.e. constant) but the voltage varies.
Report problem
with question
Send your reference
96. A control synchro system pointer is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: motor driven
This question has been asked 5397 times with a success rate of 67 percent.
The receiver of a control synchro is effectively
speed synchronous motor
Comment/Reference:
Report problem
with question
Send your reference
A desynn instrument has a positive regular increasing error, you would
97.
adjust
Your Answer: (No Answer Given) INCORRECT
Correct Answer: lever length
This question has been asked 5304 times with a success rate of 69 percent.
A regular increasing error is an indication of i
lever length.
Comment/Reference:
Report problem
with question
Send your reference
98. The output of a tachogenerator is
Your Answer: (No Answer Given) INCORRECT
Correct Answer: proportional to speed of rotation
This question has been asked 3860 times with a success rate of 81 percent.
(No Comment/Reference Available)
Comment/Reference:
Report problem
with question
Send your reference
99. The induced signal in the output coils of the magnesyn system
Your Answer: (No Answer Given) INCORRECT
Correct Answer: is of a value of 800 Hz
This question has been asked 4808 times with a success rate of 66 percent.
A signal from the permanent magnet flux is in
time the soft iron comes out of saturation. Th
Comment/Reference: the supply is 400 Hz the induced signal is 800
Report problem
with question
Send your reference
In a resolver synchro the stator windings are electrically displaced
100.
by
Your Answer: (No Answer Given) INCORRECT
Correct Answer: 90°
This question has been asked 3711 times with a success rate of 76 percent.
Comment/Reference: Pallett Aircraft Instruments and Integrated Sy
135.
Report problem
with question
Send your reference
Buy the TTS Study Notes for Module 4
High quality study notes for Module 4 from Total Training Support. Available in printed hard-copy or ebook
format.
Module 4 Study Notes - Printed Hard Copy
Delivered to your home, anywhere, worldwide.
Module 4 Study Notes - Ebook Format
Instant access on your PC, tablet or phone.
Privacy Policy
Terms and Conditions
Equal Opportunities and Diversity
Quality Policy
Contact
Copyright © 2024 Total Training Support. All Rights Reserved.
LOADING...