We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20
What happens if you wanted to take one
network address and create six networks
from it? Some of the benefits of subnetting include: Reduced network traffic Optimized network performance Simplified management Because of the subnet mask we used, all these computers are part of the one network marked in blue. This also means that any one of these hosts (computers, router and server) can communicate with each other. If we now wanted to partition this network into smaller segments, then we would need to change the subnet mask appropriately so we can get the desired result. Let's say we needed to change the subnet mask from 255.255.255.0 to 255.255.255.224 on each configured host. Do you think computers that are on the same physical network but configured to be on separate subnets are able to communicate ? The answer is "no". Why ? So how can two hosts in two different subnets talk to each other ? 1. Using a Server with 2 Network Cards 2. Binding 2 IP Addresses to the same network card 3. Installing a router By connecting each network card to one of our networks and configuring the network cards so that each one belongs to one subnet/network we can route packets between them. This method is possibly the best and easiest way around our problem. We use the same network card on the NetWare server and bind another IP Address to it. If this was a large network, then a router could possibly be the ideal solution. To create subnetworks, you take bits from the host portion of the IP address and reserve them to define the subnet address. This means fewer bits for hosts, so the more subnets, the fewer bits available for defining hosts. 1. Determine the number of required network IDs: One for each subnet One for each wide area network connection 2. Determine the number of required host IDs per subnet: One for each TCP/IP host One for each router interface 3. Based on the above requirements, create the following: One subnet mask for your entire network A unique subnet ID for each physical segment A range of host IDs for each subnet subnet mask is 32-bit value that allows the recipient of IP packets to distinguish the network ID portion of the IP address from the host ID portion of the IP address. When assigning addresses you set both the IP address and subnet mask. Not all networks need subnets, meaning they use the default subnet mask. Default subnet mask is found by setting all network address to 1 for each class. the method that ISPs (Internet Service Providers) use to allocate an amount of addresses to a company, a home—a customer. 192.168.10.32/28 – the number after the slash tells you how many bits of the subnet mask are turned on (1). This is an address with IP 192.168.10.32 and subnet mask 11111111. 11111111. 11111111.11110000 = 255.255.255.240 !" #$ $ %
many different ways to subnet a network.
Binary Method Fast Way Even in your head!!! Please go through subnetting.pdf on your lecture notes for binary method. ! "
Before starting, you need to do is answer
five simple questions: 1. How many subnets does the chosen subnet mask produce? 2. How many valid hosts per subnet are available? 3. What are the valid subnets? 4. What’s the broadcast address of each subnet? 5. What are the valid hosts in each subnet? How many subnets? 2x = number of subnets. x is the number of masked bits, or the 1s. For example, given a class C subnet mask of 255.255.255.192, the number of ones gives us 22 = 4 subnets.
Note that we only count the number of ones that
are found in the host part of the subnet mask. For class C address 255.255.255.0 is the default subnet, 192=11000000 in binary, so there are only 2 ones. How many hosts per subnet? 2y – 2 = number of hosts per subnet. y is the number of unmasked bits, or the 0s. For example, in 11000000, the number of zeros gives us 26 – 2 = 62 hosts per subnet. You need to subtract two for the subnet address and the broadcast address, which are not valid hosts. What are the valid subnets? First calculate the block size. 256 – subnet mask = block size, or increment number. An example would be 256 – 192 = 64. The block size of a 192 mask is always 64. Second, start counting at zero in blocks of 64 until you reach the subnet mask value and these are your subnets. 0, 64, 128, 192. What’s the broadcast address for each subnet? Since we counted our subnets in the last section as 0, 64, 128, and 192, the broadcast address is always the number right before the next subnet. For example, the 0 subnet has a broadcast address of 63 because the next subnet is 64. The 64 subnet has a broadcast address of 127 because the next subnet is 128, etc. And remember, the broadcast of the last subnet is always 255 for Class C. What are the valid hosts? Valid hosts are the numbers between the subnets, omitting all the 0s and all 1s. For example, if 64 is the subnet number and 127 is the broadcast address, then 65–126 is the valid host range— it’s always the numbers between the subnet address and the broadcast address. These are the addresses you assign to nodes. #$ % We’re going to subnet the network address 192.168.10.0 and subnet mask 255.255.255.224. 1. How many subnets? 224 is 11100000, so our equation would be 23 = 8. 2. How many hosts? 25 – 2 = 30. 3. What are the valid subnets? 256 – 224 = 32. We just start at zero and count to the subnet mask value in blocks (increments) of 32: 0, 32, 64, 96, 128, 160, 192, 224. 4. What’s the broadcast address for each subnet? always the number right before the next subnet 5. What are the valid hosts? the numbers between the subnet number and the broadcast address To answer questions 4 and 5, first just write out the subnets, then write out the broadcast addresses— the number right before the next subnet. Lastly, fill in the host addresses.
So now we have 192.168.10.1/27 – 192.168.10.30/27 ntk 1 192.168.10.33/27 - 192.168.10.62/27 ntk 2 upto … 192.168.10.225/27 - 192.168.10.254/27 ntk 8 &' %
Do full subnetting for the following
addresses. 1. 192.168.10.0/28 2. 192.0.10.0/30 3. 192.1.1.0/25 What is the maximum and minimum CIDR values for a class C network?