Relative and differential

pressure transmitter type 652

Pressure range
0 ... 50 1000 mbar

Type 652 pressure transmitters are ideally suited to the continuous High overpressure safety margin 10/20
monitoring of liquid and gas flow (or level) in heating, ventilation bar on P1
and process technology.
3 standardised output signals for direct
Their especially rugged construction allows a single port over-
Processing in control / monitoring systems
pressure of up to 20 bar, depending upon pressure range.
Functionally simple, rugged mechanics
with high operating reliability
Also for slightly aggressive liquids and
gases
Attractive price / performance ratio

Huba Control type 652 - Technical data subject to change - Edition 01/2011 1/5
 Technical overview
Pressure range
Relative and differential 0 ... 50 1000 mbar

Operating conditions
Medium Liquids and neutral gases
NBR-based 0 ... +80 ÀC
FPM -10 ... +80 ÀC
Temperature EPDM -10 ... +80 ÀC
Q (Silicone) -40 ... +80 ÀC
Storage -40 ... +80 ÀC
< 200 mbar 10 bar
Tolerable overload (P1 > P2)
> 500 mbar 20 bar
Rupture pressure 30 bar

Materials in contact with the medium

NBR-based
EPDM
Diaphragm
FPM
Silicon
Anodized aluminium
Case Brass
Brass chemical nickel-plated
X14CrMoS17 1.4104
X5CrNi18-10 1.4301
Other components X10CrNi18-8 1.4310
Steel category A2 for screws
Polyacetate-C, Polyamide

Electrical overview
0 ... 10 V
Output (3 wire) 0 ... 20 mA
4 ... 20 mA
Power supply 20 ... 30 VDC / 24 VAC +15% / -10%
Current load < 300 Ohm
Load
Voltage load > 10 kOhm
0 ... 10 V 35 mA
Current consumption 0 ... 20 mA max. 55 mA
4 ... 20 mA max. 55 mA
Polarity reversal protection Short circuit proof and with polarity reversal protection

Dynamic response
Response time < 10 ms
Load cycle < 10 Hz

Protection standard
With plastic cover (PG9) IP 65

Electrical connection
Screw terminals

Pressure connection (P1 > P2)

Inside thread G⅛
Straight screwed connection Zinc plated steel with NBR seal for pipe (± 6 mm) G⅛
Screwed Socket CuZn nickel plated for tube(± 6 mm) G⅛

Installation arrangement
Unrestricted. The transmitter is calibrated in the factory with the diaphragm positoned vertically. In the case of liquid media vent screw up, i.e. pressure connection down 1)

Tests / Admissions
Electromagnetic compatibility CE conformity acc. EN 61326-2-3

Weight
With aluminium pressure case ~ 394 g
With brass pressure case ~ 1030 g

Packaging
Single packaging in cardboard

Legend to cross-section drawing

1 Pressure case
2 Diaphragm
3 Permanent magnet
4 Electronics
5 Cover
6 PG9 Union
7 Vent
P1 Higher pressure / lower vacuum
P2 Lower pressure / higher vacuum

1)
Recommendation

2/5 Huba Control type 652 - Technical data subject to change - Edition 01/2011
Accuracy

Parameter Unit Test conditions: 25 ÀC, 45% RH, power supply 24 VDC

Tolerance zero point max. % fs μ 1.0

Tolerance full scale max. % fs μ 1.0
Resolution % fs 0.2
Total of linearity,
Hysteresis and repeatability max. % fs μ 1.5
TC zero point 1) max. % fs/10 K μ 0.8
TC sensitivity 1) typ. % fs/10 K μ 0.3
TC sensitivity 1) max. % fs/10 K μ 0.6

Order code selection table type 652.9 X X X X X X X X X X

Pressure ranges 2) 0 ⁄ 50 mbar 0
0 ⁄ 100 mbar 1
0 ⁄ 200 mbar 2
0 ⁄ 500 mbar 3
0 ⁄ 1000 mbar 4
Output 3) 0 ... 10 V 0
0 ... 20 mA 1
4 ... 20 mA 4
Linearity μ 1.5% FS 1
Power supply (IN) 20 ... 30 VDC / 24 VAC +15% / -10% 0
Electrical connection Screw terminals (Protection class with cover IP 65) 0
Pressure connections Inside thread G ⅛ 0
Straight screwed connection G ⅛ Stainless steel 1.4571 / AISI 316Ti for pipe (± 6 mm) 1
Screwed socket G ⅛ CuZn vni (± 6 mm) 2
Pressure case Anodized aluminium black 0
Brass 1
Nickel-plated brass 2
Diaphragme NBR-based 0
FPM 1
EPDM 2
Q (Silicon) 3
Mounting Without mounting bracket 0 0
With mounting bracket type A 0 1
With mounting bracket type B 0 2

Accessories 4)
Order number
Mounting bracket type A 100996
Mounting bracket type B 100997
Straight screwed connection G ⅛ Stainless steel 1.4571 / AISI 316Ti for pipe (± 6 mm) 106744
Screwed Socket G ⅛ CuZn nickel plated for tube (± 6 mm) 108239
Calibration certificate 104551

1)
TC = Temperature coefficient 2)
Other pressure range on request 3)
Other output signals on request 4)
Accessories supplied loose

Huba Control type 652 - Technical data subject to change - Edition 01/2011 3/5
 Dimensions in mm / Electrical connections

IN

Accessories

Straight screwed connector G ⅛ Screwed Socket G ⅛

Sealing NBR

Mounting bracket type A Mounting bracket type B

4/5 Huba Control type 652 - Technical data subject to change - Edition 01/2011
 Huba Control AG
Headquarters
Industriestrasse 17
5436 Würenlos
Telefon +41 (0) 56 436 82 00
Telefax +41 (0) 56 436 82 82
[email protected]

Huba Control AG
Niederlassung Deutschland
Schlattgrabenstrasse 24
72141 Walddorfhäslach
Telefon +49 (0) 7127 23 93 00
Telefax +49 (0) 7127 23 93 20
[email protected]

Huba Control SA
Succursale France
Rue Lavoisier
Technopôle Forbach-Sud
57602 Forbach Cedex
Téléphone +33 (0) 387 847 300
Télécopieur +33 (0) 387 847 301
[email protected]

Huba Control AG
Vestiging Nederland
Hamseweg 20A
3828 AD Hoogland
Telefoon +31 (0) 33 433 03 66
Telefax +31 (0) 33 433 03 77
[email protected]

Huba Control AG
Branch Office United Kingdom
Unit 3 Network Point, Range Road
Witney Oxfordshire OX29 0YD
Phone +44 (0) 1993 776667
Fax +44 (0) 1993 776671
[email protected]

Huba Control AG
Rep. Office Singapore
No. 16 Ayer Rajah Crescent Witney
#06-06B Tempco Technominium
139965 Singapore
Phone +65 (0) 61 004 822
Fax +65 (0) 63 994 822
[email protected]

Huba Control AG
Rep. Office China
CBC Building, 49A Wuyi Road
Shanghai 200050
Phone +86 (0) 21 511 808 21
Fax +86 (0) 21 515 520 99
[email protected]

www.hubacontrol.com
Huba Control type 652 - Technical data subject to change - Edition 01/2011 5/5