Scribd Logo
Upload

Welcome to Scribd!

  • 10 views

    Techdoc Print Page

    Uploaded by

    Marcos Calderon Reyna

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Techdoc Print Page

    Uploaded by

    Marcos Calderon Reyna
    10 views3 pages

    Original Title

    techdoc_print_page

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    10 views3 pages

    Techdoc Print Page

    Uploaded by

    Marcos Calderon Reyna

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    3406C Generator Set C2Y00001-UP(SEBP5549 - 17) - Documentación Page 1 of 3

    Cerrar SIS

    Pantalla anterior

    Producto: GENERATOR SET


    Modelo: 3406C GENERATOR SET C2Y02016
    Configuración: 3406C Generator Set C2Y00001-UP

    Especificaciones
    3406C GENERATOR SET ENGINE
    Número de medio -RENR1292-02 Fecha de publicación -01/08/2005 Fecha de actualización -03/03/2009

    RENR12920017

    Camshaft
    SMCS - 1205-010

    (1) Gear. If new gear is required, replace camshaft assembly. The heat treatment of the gear is
    damaged if heated.

    (2) Diameter of the surfaces (journals) for the camshaft bearings (new) ... 69.850 ± 0.013 mm
    (2.7500 ± .0005 in)

    Bore in front bearing for the camshaft (after assembly) ... 69.969 ± 0.048 mm (2.7547 ± .0019 in)

    Bore in the other six bearings for the camshaft (after assembly) ... 69.982 ± 0.061 mm (2.7552
    ± .0024 in)

    (3) Thickness of thrust plate (new) ... 4.65 ± 0.03 mm (.183 ± .001 in)

    Thickness of groove in camshaft for thrust plate (new) ... 4.83 ± 0.06 mm (.190 ± .002 in)

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/04/2019
    3406C Generator Set C2Y00001-UP(SEBP5549 - 17) - Documentación Page 2 of 3

    End play of the camshaft ... 0.10 to 0.26 mm (.004 to .010 in)

    (4) Camshaft.

    (5) Height of camshaft lobes.

    To find lobe height, use the procedure that follows:

    A. Measure camshaft lobe height (5).

    B. Measure base circle (7).

    C. Subtract base circle (STEP B) from lobe height (STEP A). The difference is actual lobe lift (6).

    D. Specified camshaft lobe lift (6) is:

    a. Exhaust lobe ... 10.210 mm (.4019 in)


    b. Inlet lobe ... 10.212 mm (.4021 in)

    Maximum permissible difference between actual lobe lift (STEP C) and specified lobe lift (STEP
    D) is 0.13 mm (.005 in).

    Inlet Valve Timing


    1. Check the No. 1 inlet valve lash with the engine stopped. The valve lash must be 0.30 to 0.46
    mm (.012 to .018 in). If the valve lash is not in this range, adjust the lash to 0.38 mm (.015 in).

    2. Mark Top Center Position of the crankshaft on the vibration damper or pulley.

    3. Use a dial indicator to measure the inlet valve movement.

    4. Rotate the crankshaft in the direction of normal engine rotation. Stop when the inlet valve is
    1.91 mm (.075 in) off its seat in the opening sequence.

    At this point the crankshaft Top Center Position Mark must be ... 1 ± 2 degrees After Top Center

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/04/2019
    3406C Generator Set C2Y00001-UP(SEBP5549 - 17) - Documentación Page 3 of 3

    Copyright 1993 - 2019 Caterpillar Inc. Mon Apr 22 08:24:02 EST 2019
    Todos los derechos reservados.
    Red privada para licenciados del SIS.

    https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/04/2019

    You might also like