Class Notes

57:020 (ENGR:2510)
Fluid Mechanics
Class Notes
Fall 2016
Prepared by:
Professor Fred Stern
Typed by: Stephanie Schrader (Fall 1999)

Corrected by: Jun Shao (Fall 2003, Fall 2005)
Corrected by: Hyunse Yoon (Fall 2007 ∼ Fall 2016)

Corrected by: Jun Shao, Tao Xing (Fall 2006)
Corrected by: Timur Kent Dogan (Fall 2014)

57:020 (ENGR:2510) Fluid Mechanics Chapter 1
Professor Fred Stern Fall 2016 1
CHAPTER 1: INTRODUCTION AND

BASIC CONCEPTS
Fluids and the no-slip condition

Fluid mechanics is the science and technology of flu-
ids either at rest (fluid statics) or in motion (fluid dynamics)
and their effects on boundaries such as solid surfaces or in-
terfaces with other fluids.
Definition of a fluid: A substance that deforms continuous-
ly when subjected to a shear stress
Consider a fluid between two parallel plates, which is
subjected to a shear stress due to the impulsive motion of
the upper plate
u=U
No slip condition: no relative
Fluid motion between fluid and
Element
boundary, i.e., fluid in contact
u=0 with lower plate is stationary,
t=0
whereas fluid in contact with
upper plate moves at speed U.
τ Fluid deforms, i.e., un-
θ dergoes rate of strain θ due to
shear stress τ
τ
t=∆t
Newtonian fluid: τ ∝ θ = rate of strain

τ = μ θ
µ = coefficient of viscosity
Such behavior is different from solids, which resist shear

by static deformation (up to elastic limit of material)
τ
Elastic solid: τ ∝ γ = strain
γ
Solid τ=Gγ
τ G = shear modulus
t=0 t=∆t
Both liquids and gases behave as fluids
Liquids:
Closely spaced molecules with large intermolecular forces
Retain volume and take shape of container
container
liquid
Gases:
Widely spaced molecules with small intermolecular forces
Take volume and shape of container
gas
Recall p-v-T diagram from thermodynamics:
single phase, two phase, triple point (point at which solid,
liquid, and vapor are all in equilibrium), critical point
(maximum pressure at which liquid and vapor are both in
equilibrium).
Liquids, gases, and two-phase liquid-vapor behave as flu-

ids.
Continuum Hypothesis
In this course, the assumption is made that the fluid be-

haves as a continuum, i.e., the number of molecules within
the smallest region of interest (a point) are sufficient that all
fluid properties are point functions (single valued at a
point).
Consider definition of density ρ of a fluid

For example:
δm x = position vector = xi + yj + zk
ρ ( x, t ) =
δV → δV* δV
lim
t = time
δV* = limiting volume below which molecular variations

may be important and above which macroscopic variations
may be important
δV* ≈ 10-9 mm3 (or length scale of l* ≈ 10-6 m) for all liq-
uids and for gases at atmospheric pressure
tains 3x107 molecules such that δM/δV = constant = ρ

10-9 mm3 air (at standard conditions, 20°C and 1 atm) con-
about 10-3 – 100 mm3 >> δV* and that the “scale” of macro-
Note that typical “smallest” measurement volumes are
scopic variations are very problem dependent

Exception: rarefied gas flow
δ∀* defines a point in the fluid, i.e., a fluid particle or infini-

tesimal material element used for deriving governing differ-
ential equations of fluid dynamics and at which all fluid
properties are point functions:
λ = mean free path = 6×10-8 m

l* =10-6 m >> molecular length scales
tλ = 10-10 s = time between collisions

l* = 10-6 m << fluid length scales l = 10-4 m
For laminar flow: lmax ≈ smallest geometry scales of the
flow
Umax < U transition to turbulent flow
For turbulent flow: lmax and Umax determined by Kolmogorov
scales at which viscous dissipation takes place, which for
η ≈ 2×10-5 m (ship)/2.3×10-5 m (airplane)

typical ship/airplane,
uη ≈ 0.05 m/s (ship)/1.64 m/s (airplane)

tη ≈ 4×10-4 s (ship)/1.4×10-5 s (airplane)
Properties of Fluids
ty µ and density ρ, which we have already discussed with

Fluids are characterized by their properties such as viscosi-
reference to definition of shear stress τ = μθ and the contin-

uum hypothesis.
(1) Kinematic: Linear (�) and angular (�⁄2) velocity,

rate of strain (�� ), Vorticity (�), and acceleration (�)
(2) Transport: Viscosity (�), thermal conductivity (�),

and mass diffusivity (�)
(3) Thermodynamic: Pressure (�), density (�), tempera-

ture (�), internal energy (��), enthalpy (ℎ = �� +
�⁄�), specific heat (�� , �� , � = �� ⁄�� , etc.)
(4) Miscellaneous: Surface tension (�), vapor pressure

(�� ), etc.
Properties can be both dimensional (i.e., expressed in either

SI or BG units) or non-dimensional:
Figure B.1 Dynamic (absolute) viscosity of common fluids as a

function of temperature.
Figure B.2 Kinematic viscosity of common fluids (at atmospheric
pressure) as a function of temperature.
Table B.1 Physical Properties of Water (BG Units)
Table B.2 Physical Properties of Water (SI Units)
Table B.3 Physical Properties of Air at Standard Atmospheric
Pressure (BG Units)
Table B.4 Physical Properties of Air at Standard Atmospheric
Pressure (SI Units)
Table 1.5 Approximate Physical Properties of Some Common Liq-
uids (BG Units)
Table 1.6 Approximate Physical Properties of Some Common Liq-
uids (SI Units)
Table 1.7 Approximate Physical Properties of Some Common
Gases at Standard Atmospheric Pressure (BG Units)
Table 1.8 Approximate Physical Properties of Some Common
Gases at Standard Atmospheric Pressure (SI Units)
Basic Units
System International and British Gravitational Systems
Primary Units SI BG
Mass M kg slug=32.2lbm
Length L m ft
°C (°K) °F (°R)
Time t s s
Temperature T
°K = °C + 273
Temperature Conversion:
°R = °F + 460
°K and °R are absolute scales, i.e., 0 at absolute zero.

Freezing point of water is at 0°C and 32°F.
Secondary
(derived) units Dimension SI BG
velocity V L/t m/s ft/s
acceleration a L/t2 m/s2 ft/s2
force F ML/t2 N (kg⋅m/s2) lbf
density ρ
pressure p F/L2 Pa (N/m2) lbf/ft2
M/L3 kg/m3 slug/ft3
internal energy u FL/M J/kg (N⋅m/kg) BTU/lbm
Table 1.3 Conversion Factors from BG and EE Units to SI Units.

Table 1.4 Conversion Factors from SI Units to BG and EE Units.
Weight and Mass
F = ma Newton’s second law (valid for both solids

and fluids)
Weight = force on object due to gravity
W = mg g = 9.81 m/s2
= 32.2 ft/s2
SI: W (N) = m (kg) ⋅ 9.81 m/s2
BG: W (lbf) = m(slug) ⋅ 32.2ft/ s2
m(lbm )
EE: W (lbf) = ⋅32.2 ft/s2
lbm ⋅ ft
gc
g c = 32.2 2 = 32.2
lbm
s ⋅ lbf
, i.e., 1 slug = 32.2 lbm
slug
1 N = 1 kg ⋅ 1 m/s2
1 lbf = 1 slug ⋅ 1 ft/s2
System; Extensive and Intensive Properties
System = fixed amount of matter

= mass m
Therefore, by definition
=0
d ( m)
dt
Properties are further distinguished as being either exten-

sive or intensive.
Extensive properties: depend on total mass of system,

e.g., m and W
system, e.g., p (force/area) and ρ

Intensive properties: independent of amount of mass of
(mass/volume)
Properties Involving the Mass or Weight of the

Fluid
Specific Weight, γ = gravitational force (i.e., weight) per

unit volume V
= W/ V
= ρg
= mg/ V
N/m3
(Note that specific properties are derived from intensive or
extensive properties per unit mass or volume)
Mass Density ρ = mass per unit volume
= m/ V kg/m3
Specific Gravity S = ratio of γliquid to γwater at standard T = 4°C

= γ/γwater, 4°C dimensionless
(or γair at standard conditions for gases)
γwater, 4°C = 9810 N/m3 for T = 4°C and atmospheric pressure

γair = 12.01 N/m3 at standard atmosphere (T = 15°C and p =
101.33 kPa)
Variation in Density
gases: ρ = ρ (gas, T, p) equation of state (p-v-T)

= p/RT ideal gas
R = R (gas)
ρ (air) = 1.225 kg/m3 at Standard Atmosphere

e.g. R (air) = 287.05 N⋅m/kg⋅°K
liquids: ρ ∼ constant
(T = 15°C and p = 101.33 kPa)
Water
Note: For a change in temperature from 0 to 100°C, density changes about

29% for air while only about 4% for water.
Liquid and temperature Density Density

(kg/m3) (slugs/ft3)
Water 20oC (68oF) 998 1.94
Ethyl alcohol 20oC (68oF) 799 1.55
Glycerine 20oC (68oF) 1,260 2.45
Kerosene 20oC (68oF) 814 1.58
Mercury 20oC (68oF) 13,350 26.3
Sea water 10oC at 3.3% salinity 1,026 1.99
SAE 10W 38oC(100oF) 870 1.69
SAE 10W-30 8oC(100oF) 880 1.71
SAE 30 38oC(100oF) 880 1.71
For greater accuracy can also use p-v-T diagram
ρ = ρ (liquid, T, p)
ρ
ρ
T
p
Properties Involving the Flow of Heat
For flows involving heat transfer such as gas dynamics ad-

ditional thermodynamic properties are important, e.g.
specific heats cp and cv J/kg⋅°K

specific internal energy û J/kg
specific enthalpy h = û + p/ρ J/kg
Viscosity
Recall definition of a fluid (substance that deforms contin-

uously when subjected to a shear stress) and Newtonian
fluid shear / rate-of-strain relationship: τ = μθ .
Reconsider flow between fixed and moving parallel plates

(Couette flow)
δuδt=distance fluid parti-

cle travels in time δt
y
δf at δt
δy
u=U
h
δf at t
u(y)=velocity profile
=
U δθ
y δf=fluid
h element
u=0
Newtonian fluid: τ = μθ = μ

δθ
δt
tan δθ = or δθ = for small δθ
δuδt δuδt
δy δy
δu
therefore δθ = i.e., θ =
δy
du
= velocity gradient
dy
τ=μ
du
and
dy
Exact solution for Couette flow is a linear velocity profile
u( y) =
U
y Note: u(0) = 0 and u(h) = U
h
i.e., satisfies no-slip
τ=μ
U boundary condition
= constant
h
where
U/h = velocity gradient = rate of strain
µ = coefficient of viscosity = proportionality constant for

Newtonian fluid
τ
µ= = = 2
N m 2 Ns
du m
m m
µ m2
dy s
ν= =
ρ s
= kinematic viscosity
µ = µ(fluid;T,p) = µ(gas/liquid;T)
gas and liquid µ p, but small ∆µ

µ T
liquid: µ T
gas: Due to structural differences, more molecular
activity for gases, decreased cohesive forces
for liquids
Newtonian vs. Non-Newtonian Fluids
τ  du/dy 
τ ∝ du/dy
Dilatant (Shear thickening):
Pseudo plastic (Shear thinning): τ  du/dy 

Newtonian:
Bingham plastic: Requires τ before becomes fluid

Example: toothpaste, mayonnaise
Newtonian Fluids Non-Newtonian Fluids
��
�∝ �∝� �
��
µ = slope n > 1 (shear thickening) Slope
τ; ex) cornstarch, quick-

increases with increasing
sand
creases with increasing τ;

n < 1 (shear thinning) Slope de-
ex) blood, paint, liquid

plastic
Elasticity (i.e., compressibility)
Increasing/decreasing pressure corresponds to contrac-

tion/expansion of a fluid. The amount of deformation is
called elasticity: �� = bulk modulus of elasticity
�� > 0 ⇒
��
�� ∝ − ; Constant = �� <0
Increase pressure, decrease volume. ∴ minus sign used
� �
and by definition, � = ��
�� = �� + �� = 0
��
−� = �
Thus,
��
�� = − = =� [�⁄�2 ]
�� ⁄� ��⁄� ��
Liquids are in general incompressible, e.g.

�� = 2.2 GN/m2
i.e. Δ� = 0.05%� for ∆p = 1MN/m2
water
(G=Giga=109 M=Mega=106 k=kilo=103)
Gases are in general compressible, e.g. for ideal gas (i.e.,

� = ��) at T = constant (isothermal)
= RT
dρ
dp
Ev = ρRT = p
Vapor Pressure and Cavitation
When the pressure of a liquid falls below the vapor pres-

sure it evaporates, i.e., changes to a gas. If the pressure
drop is due to temperature effects alone, the process is
called boiling. If the pressure drop is due to fluid velocity,
the process is called cavitation. Cavitation is common in
regions of high velocity, i.e., low p such as on turbine
blades and marine propellers.
high V low p isobars

(suction side)
streamlines around lifting

surface (i.e. lines tangent to
low V high p velocity vector)
(pressure side)
p − pv
Cavitation number, �� =
ρV∞2
1
2
�� < 0 implies cavitation

Surface Tension and Capillary Effects
At the interface of two immiscible fluids (e.g., a liquid and

a gas), forces develop to cause the surface to behave as if it
were a stretched membrane. Molecules in the interior at-
tract each other equally, whereas molecules along the sur-
face are subject to a net force due to the absence of neigh-
bor molecules. The intensity of the molecular attraction per
unit length along any line in the surface is call the surface
tension and is designated by the Greek symbol �.
Fσ = surface tension force

AIR
Fσ Fσ
Interface
neighbors such that surface is in tension σ per unit length

Near surface forces are increased due to absence of
Away from interface

WATER molecular forces are
equal in all directions
σair/water = 0.073 N/m

Fσ = σ × L = line force with direction normal to the cut
L =length of cut through the interface
Effects of surface tension:
Contact angle:
θ < 90o, Wetting θ > 90o, Non-wetting

e.g., Water, θ ≈ 0° e.g., Mercury, θ≈130°
1. Capillary action in small tube

∆h = 4σ γd
2. Pressure difference across curved interface
∆p = σ/R R = radius of curvature
3. Transformation of liquid jet into droplets
4. Binding of wetted granular material such as sand
5. Capillary waves: surface tension acts as restoring force
resulting in interfacial waves called capillary waves
Capillary tube
Fσ Fσ Fluid attaches to solid with contact an-

gle θ due to surface tension effect and
∆h
wetty properties
θ
θ= contact angle
water
reservoir
d
Example:
Fσ = σ × L , L=length of contact line between fluid & solid

Capillary tube d = 1.6mm = 0.0016m
(i.e., L = πD = circumference)
water reservoir at 20° C, σ = 0.073 N/m, γ = 9790 N/m3
∆h = ?
ΣFz = 0
Fσ,z - W = 0
σπd cosθ - ρgV = 0 θ ∼ 0° ⇒ cosθ = 1
ρg = γ
πd 2
σπd − γ∆h =0 V = Δh
πd 2
4 4 =Volume of flu-
4σ
id above reser-
∆h = = 18.6mm
voir
γd
Pressure jump across curved interfaces
(a) Cylindrical interface

Force Balance:
2σL = 2 RL⋅(pi – po)
∆p = σ/R
pi > po, i.e. pressure is larger on concave vs. convex

side of interface
π⋅2Rσ = πR2∆p → ∆p = 2σ/R

(b) Spherical interface (Droplets)
4�
Bubble: � ⋅ 2�� + � ⋅ 2�� = ��2 Δ� ⇒ Δ� = �
∆p = σ(R1-1 + R2-1)
(c) General interface
R1,2 = principal radii of curvature

A brief history of fluid mechanics

See textbook section 1.10. (page 27)
Fluid Mechanics and Flow Classification
Hydrodynamics: flow of fluids for which density is con-

stant such as liquids and low-speed gases. If in addition
fluid properties are constant, temperature and heat transfer
effects are uncoupled such that they can be treated sepa-
rately.
Examples: hydraulics, low-speed aerodynamics, ship hy-

drodynamics, liquid and low-speed gas pipe systems
Gas Dynamics: flow of fluids for which density is variable

such as high-speed gases. Temperature and heat transfer
effects are coupled and must be treated concurrently.
Examples: high-speed aerodynamics, gas turbines,

high-speed gas pipe systems, upper atmosphere

Class Notes

Uploaded by

Copyright:

Available Formats

Class Notes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Class Notes

Uploaded by

Copyright:

Available Formats

57:020 (ENGR:2510)

Typed by: Stephanie Schrader (Fall 1999)

Corrected by: Hyunse Yoon (Fall 2007 ∼ Fall 2016)

Corrected by: Timur Kent Dogan (Fall 2014)

CHAPTER 1: INTRODUCTION AND

Fluids and the no-slip condition

Newtonian fluid: τ ∝ θ = rate of strain

Such behavior is different from solids, which resist shear

Both liquids and gases behave as fluids

Liquids, gases, and two-phase liquid-vapor behave as flu-

In this course, the assumption is made that the fluid be-

Consider definition of density ρ of a fluid

δV* = limiting volume below which molecular variations

tains 3x107 molecules such that δM/δV = constant = ρ

scopic variations are very problem dependent

Exception: rarefied gas flow

δ∀* defines a point in the fluid, i.e., a fluid particle or infini-

λ = mean free path = 6×10-8 m

tλ = 10-10 s = time between collisions

η ≈ 2×10-5 m (ship)/2.3×10-5 m (airplane)

uη ≈ 0.05 m/s (ship)/1.64 m/s (airplane)

ty µ and density ρ, which we have already discussed with

reference to definition of shear stress τ = μθ and the contin-

(1) Kinematic: Linear (�) and angular (�⁄2) velocity,

(2) Transport: Viscosity (�), thermal conductivity (�),

(3) Thermodynamic: Pressure (�), density (�), tempera-

(4) Miscellaneous: Surface tension (�), vapor pressure

Properties can be both dimensional (i.e., expressed in either

Figure B.1 Dynamic (absolute) viscosity of common fluids as a

System International and British Gravitational Systems

°K and °R are absolute scales, i.e., 0 at absolute zero.

Table 1.3 Conversion Factors from BG and EE Units to SI Units.

F = ma Newton’s second law (valid for both solids

SI: W (N) = m (kg) ⋅ 9.81 m/s2

BG: W (lbf) = m(slug) ⋅ 32.2ft/ s2

System; Extensive and Intensive Properties

System = fixed amount of matter

Properties are further distinguished as being either exten-

Extensive properties: depend on total mass of system,

system, e.g., p (force/area) and ρ

Properties Involving the Mass or Weight of the

Specific Weight, γ = gravitational force (i.e., weight) per

Specific Gravity S = ratio of γliquid to γwater at standard T = 4°C

γwater, 4°C = 9810 N/m3 for T = 4°C and atmospheric pressure

gases: ρ = ρ (gas, T, p) equation of state (p-v-T)

ρ (air) = 1.225 kg/m3 at Standard Atmosphere

Note: For a change in temperature from 0 to 100°C, density changes about

Liquid and temperature Density Density

For greater accuracy can also use p-v-T diagram

Properties Involving the Flow of Heat

For flows involving heat transfer such as gas dynamics ad-

specific heats cp and cv J/kg⋅°K

Recall definition of a fluid (substance that deforms contin-

Reconsider flow between fixed and moving parallel plates

δuδt=distance fluid parti-

Newtonian fluid: τ = μθ = μ

U/h = velocity gradient = rate of strain

µ = coefficient of viscosity = proportionality constant for

gas and liquid µ p, but small ∆µ

Pseudo plastic (Shear thinning): τ  du/dy 