Conforms to UN GHS (Rev.

7) (2017)

SAFETY DATA SHEET

SeaForce Shield
Section 1. Identification
Product name : SeaForce Shield
Product code : 43004
Product description : Paint.
Product type : Liquid.
Other means of : Not available.
identification

Relevant identified uses of the substance or mixture and uses advised against
Use in coatings - Professional use
Supplier's details : Jotun UAE Ltd. L.L.C.
P.O.Box 3671, Dubai, U.A.E.
Tel: 009714 3395000
Fax:009714 3380666

Jotun Abu Dhabi L.L.C.

P.O.box-3714
Abu Dhabi U.A.E.
Tel: 00971 2 5510300
Fax:00971 2 5510232

[email protected]

Emergency telephone : Jotun AS, Norway

number +47 33 45 70 00

43004 1,2 43004

^(ValidationDate) 1

Section 2. Hazards identification

Classification of the : FLAMMABLE LIQUIDS - Category 3
substance or mixture ACUTE TOXICITY (oral) - Category 5
SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/EYE IRRITATION - Category 1
SKIN SENSITISATION - Category 1
REPRODUCTIVE TOXICITY - Category 2
SPECIFIC TARGET ORGAN TOXICITY - SINGLE EXPOSURE (Respiratory tract
irritation) - Category 3
SHORT-TERM (ACUTE) AQUATIC HAZARD - Category 1
LONG-TERM (CHRONIC) AQUATIC HAZARD - Category 1

GHS label elements

Hazard pictograms :

Signal word : Danger.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 1/13
SeaForce Shield

Section 2. Hazards identification

Hazard statements : H226 - Flammable liquid and vapour.
H303 - May be harmful if swallowed.
H315 - Causes skin irritation.
H317 - May cause an allergic skin reaction.
H318 - Causes serious eye damage.
H335 - May cause respiratory irritation.
H361 - Suspected of damaging fertility or the unborn child.
H410 - Very toxic to aquatic life with long lasting effects.
Precautionary statements
Prevention : P201 - Obtain special instructions before use.
P280 - Wear protective gloves, protective clothing, eye protection, face protection,
or hearing protection.
P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P273 - Avoid release to the environment.
P261 - Avoid breathing vapour.
Response : P391 - Collect spillage.
P308 + P313 - IF exposed or concerned: Get medical advice or attention.
P304 + P312 - IF INHALED: Call a POISON CENTER or doctor if you feel unwell.
P362 + P364 - Take off contaminated clothing and wash it before reuse.
P302 + P352 - IF ON SKIN: Wash with plenty of water.
P333 + P313 - If skin irritation or rash occurs: Get medical advice or attention.
P305 + P351 + P338, P310 - IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Immediately call a POISON CENTER or doctor.
Storage : P403 + P233 - Store in a well-ventilated place. Keep container tightly closed.
Disposal : P501 - Dispose of contents and container in accordance with all local, regional,
national and international regulations.
In compliance : IMO Antifouling System Convention compliant AFS/CONF/26 + IMO MEPC.331(76).

Other hazards which do not : None known.

result in classification

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of : Not available.
identification

CAS number/other identifiers

CAS number : Not applicable.
EC number : Mixture.
Product code : 43004
Ingredient name % CAS number
dicopper oxide ≥10 - <25 1317-39-1
xylene ≥10 - <22 1330-20-7
colophony ≥10 - ≤25 8050-09-7
zineb ≤10 12122-67-7
ethylbenzene ≤5 100-41-4
zinc oxide ≤5 1314-13-2
1-methoxy-2-propanol ≤3 107-98-2
hydrocarbons, C9, aromatics ≤3 64742-95-6
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 2/13
SeaForce Shield

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Get medical attention immediately. Call a poison center or physician. Immediately
flush eyes with plenty of water, occasionally lifting the upper and lower eyelids.
Check for and remove any contact lenses. Continue to rinse for at least 10 minutes.
Chemical burns must be treated promptly by a physician.
Inhalation : Get medical attention immediately. Call a poison center or physician. Remove
victim to fresh air and keep at rest in a position comfortable for breathing. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
It may be dangerous to the person providing aid to give mouth-to-mouth
resuscitation. If unconscious, place in recovery position and get medical attention
immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie,
belt or waistband. In case of inhalation of decomposition products in a fire,
symptoms may be delayed. The exposed person may need to be kept under
medical surveillance for 48 hours.
Skin contact : Get medical attention immediately. Call a poison center or physician. Wash with
plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly
by a physician. In the event of any complaints or symptoms, avoid further exposure.
Wash clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion : Get medical attention immediately. Call a poison center or physician. Wash out
mouth with water. Remove dentures if any. If material has been swallowed and the
exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Chemical burns must be treated
promptly by a physician. Never give anything by mouth to an unconscious person.
If unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : May cause respiratory irritation.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : May be harmful if swallowed.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
reduced foetal weight
increase in foetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
reduced foetal weight
increase in foetal deaths
skeletal malformations

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 3/13
SeaForce Shield

Section 4. First aid measures

Ingestion : Adverse symptoms may include the following:
stomach pains
reduced foetal weight
increase in foetal deaths
skeletal malformations

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it
is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing
thoroughly with water before removing it, or wear gloves.

See toxicological information (Section 11)

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising : Flammable liquid and vapour. Runoff to sewer may create fire or explosion hazard.
from the chemical In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion. This material is very toxic to aquatic life with
long lasting effects. Fire water contaminated with this material must be contained
and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
nitrogen oxides
sulfur oxides
metal oxide/oxides

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Do not breathe vapour or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 4/13
SeaForce Shield

Section 6. Accidental release measures

Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful
to the environment if released in large quantities. Collect spillage.

Methods and material for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach the release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations (see Section 13).
Dispose of via a licensed waste disposal contractor. Contaminated absorbent
material may pose the same hazard as the spilt product. Note: see Section 1 for
emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in
which this product is used. Avoid exposure - obtain special instructions before use.
Avoid exposure during pregnancy. Do not handle until all safety precautions have
been read and understood. Do not get in eyes or on skin or clothing. Do not
breathe vapour or mist. Do not ingest. Avoid release to the environment. Use only
with adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a
compatible material, kept tightly closed when not in use. Store and use away from
heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools.
Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in a segregated and approved
including any area. Store in original container protected from direct sunlight in a dry, cool and well-
incompatibilities ventilated area, away from incompatible materials (see Section 10) and food and
drink. Store locked up. Eliminate all ignition sources. Separate from oxidising
materials. Keep container tightly closed and sealed until ready for use. Containers
that have been opened must be carefully resealed and kept upright to prevent
leakage. Do not store in unlabelled containers. Use appropriate containment to
avoid environmental contamination. See Section 10 for incompatible materials
before handling or use.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 5/13
SeaForce Shield

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
dicopper oxide ACGIH TLV (United States, 1/2022).
TWA: 0.2 mg/m³ 8 hours. Form: Fume
xylene ACGIH TLV (United States, 1/2022).
STEL: 651 mg/m³ 15 minutes.
TWA: 434 mg/m³ 8 hours.
TWA: 20 ppm 8 hours.
colophony ACGIH TLV (United States, 1/2022). Skin
sensitiser. Inhalation sensitiser.
TWA: 0.001 mg/m³, (as total Resin acids) 8
hours. Form: Inhalable fraction
ethylbenzene ACGIH TLV (United States, 1/2022).
Ototoxicant. Notes: K
TWA: 20 ppm 8 hours. Form:
1-methoxy-2-propanol ACGIH TLV (United States, 1/2022).
STEL: 369 mg/m³ 15 minutes.
STEL: 100 ppm 15 minutes.
TWA: 184 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.

Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapour or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety eyewear complying to ISO 16321-1:2022 should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: chemical splash
goggles and/or face shield. If inhalation hazards exist, a full-face respirator may be
required instead.
Skin protection
Hand protection : There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 6/13
SeaForce Shield

Section 8. Exposure controls/personal protection

applied once exposure has occurred.
Wear suitable gloves tested to ISO 374-1:2016.
May be used, gloves(breakthrough time) 4 - 8 hours: neoprene
Not recommended, gloves(breakthrough time) < 1 hour: butyl rubber, PVC
Recommended, gloves(breakthrough time) > 8 hours: fluor rubber, nitrile rubber, 4H,
Teflon, polyvinyl alcohol (PVA)

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : If workers are exposed to concentrations above the exposure limit, they must use a
respirator according to EN 140. Use respiratory mask with charcoal and dust filter
when spraying this product, according to EN 14387(as filter combination A2-P2). In
confined spaces, use compressed-air or fresh-air respiratory equipment. When use
of roller or brush, consider use of charcoalfilter.

Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Colour : Red
Odour : Characteristic.
Odour threshold : Not applicable.
pH : Not applicable.
Melting point : Not applicable.
Boiling point : Lowest known value: 120.17°C (248.3°F) (1-methoxy-2-propanol). Weighted
average: 137.48°C (279.5°F)
Flash point : Closed cup: 27°C (80.6°F)
Evaporation rate : Highest known value: 0.84 (ethylbenzene) Weighted average: 0.79compared with
butyl acetate
Flammability (solid, gas) : Not applicable.
Lower and upper explosive : 0.8 - 13.74%
(flammable) limits
Vapour pressure : Highest known value: 1.2 kPa (9.3 mm Hg) (at 20°C) (ethylbenzene). Weighted
average: 0.94 kPa (7.05 mm Hg) (at 20°C)
Vapour density : Highest known value: 3.7 (Air = 1) (xylene). Weighted average: 3.65 (Air = 1)
Density : 1.584 to 1.589 g/cm³
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n- : Not available.
octanol/water
Auto-ignition temperature : Lowest known value: 270°C (518°F) (1-methoxy-2-propanol).
Decomposition temperature : Not available.
Viscosity : Kinematic (40°C): >20.5 mm2/s (>20.5 cSt)

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 7/13
SeaForce Shield

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurise, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Incompatible materials : Reactive or incompatible with the following materials:
oxidising materials
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
dicopper oxide LC50 Inhalation Dusts and mists Rat 3.34 mg/l 4 hours
LD50 Oral Rat 1340 mg/kg -
xylene LC50 Inhalation Vapour Rat 20 mg/l 4 hours
LD50 Oral Rat 4300 mg/kg -
TDLo Dermal Rabbit 4300 mg/kg -
zineb LD50 Oral Rat 1850 mg/kg -
ethylbenzene LC50 Inhalation Vapour Rat - Male 17.8 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
1-methoxy-2-propanol LD50 Dermal Rabbit 13 g/kg -
LD50 Oral Rat 6600 mg/kg -
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
dicopper oxide Eyes - Cornea opacity Rabbit - 72 hours -
Eyes - Redness of the Rabbit - 48 hours -
conjunctivae
xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Skin - Mild irritant Rat - 8 hours 60 -
microliters
zinc oxide Eyes - Mild irritant Rabbit - 24 hours 500 -
mg
Skin - Mild irritant Rabbit - 24 hours 500 -
mg
1-methoxy-2-propanol Eyes - Mild irritant Rabbit - 24 hours 500 -
mg
Skin - Mild irritant Rabbit - 500 mg -
Sensitisation
Product/ingredient name Route of Species Result
exposure
colophony skin Mammal - species Sensitising
unspecified
zineb skin Mammal - species Sensitising
unspecified
Mutagenicity
Not available.
Conclusion/Summary : Not classified.
Carcinogenicity
Not available.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 8/13
SeaForce Shield

Section 11. Toxicological information

Conclusion/Summary : Not classified.
Reproductive toxicity
Product/ingredient name Maternal Fertility Developmental Species Dose Exposure
toxicity toxin
zineb - - Positive Mammal - species Route of -
unspecified exposure
unreported
Conclusion/Summary : Suspected of damaging the unborn child.
Teratogenicity
Not available.
Conclusion/Summary : Suspected of damaging the unborn child.
Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 - Respiratory tract
irritation
zineb Category 3 - Respiratory tract
irritation
1-methoxy-2-propanol Category 3 - Narcotic effects
hydrocarbons, C9, aromatics Category 3 - Respiratory tract
irritation
Category 3 Narcotic effects
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
ethylbenzene Category 2 - hearing organs
Aspiration hazard
Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1
hydrocarbons, C9, aromatics ASPIRATION HAZARD - Category 1

Information on likely routes : Not available.

of exposure
Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : May cause respiratory irritation.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : May be harmful if swallowed.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
reduced foetal weight
increase in foetal deaths
skeletal malformations

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 9/13
SeaForce Shield

Section 11. Toxicological information

Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
reduced foetal weight
increase in foetal deaths
skeletal malformations
Ingestion : Adverse symptoms may include the following:
stomach pains
reduced foetal weight
increase in foetal deaths
skeletal malformations

Delayed and immediate effects as well as chronic effects from short and long-term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.

General : Once sensitized, a severe allergic reaction may occur when subsequently exposed
to very low levels.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : Suspected of damaging the unborn child.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates
Route ATE value
Oral 2237.14 mg/kg
Dermal 7586.52 mg/kg
Inhalation (vapours) 100.35 mg/l
Inhalation (dusts and mists) 14.94 mg/l

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
dicopper oxide Acute LC50 0.075 mg/l Fresh water Fish - Danio rerio 96 hours
Chronic NOEC 0.001 mg/l Algae -
Chronic NOEC 0.0052 mg/l Algae -
xylene Acute LC50 8500 μg/l Marine water Crustaceans - Palaemonetes 48 hours
pugio
Acute LC50 13400 μg/l Fresh water Fish - Pimephales promelas 96 hours
zineb Acute EC50 0.38 mg/l Fresh water Algae - Pseudokirchneriella 96 hours
subcapitata

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 10/13
SeaForce Shield

Section 12. Ecological information

Acute LC50 970 to 1800 μg/l Fresh Daphnia - Daphnia magna 48 hours
water
Acute LC50 20.8 ppm Fresh water Fish - Oncorhynchus mykiss 96 hours
Acute LC50 0.225 mg/l Fish 96 hours
Chronic NOEC 0.05 mg/l Fresh water Algae - Chlorella vulgaris 96 hours
Chronic NOEC 0.05 mg/l Fresh water Algae - Scenedesmus 96 hours
quadricauda
ethylbenzene Acute EC50 7700 μg/l Marine water Algae - Skeletonema costatum 96 hours
Acute EC50 2.93 mg/l Daphnia 48 hours
Acute LC50 4.2 mg/l Fish 96 hours
zinc oxide Acute LC50 1.1 ppm Fresh water Fish - Oncorhynchus mykiss 96 hours
Chronic NOEC 0.02 mg/l Fresh water Algae - Pseudokirchneriella 72 hours
subcapitata - Exponential
growth phase
hydrocarbons, C9, aromatics Acute EC50 <10 mg/l Daphnia 48 hours
Acute IC50 <10 mg/l Algae 72 hours
Acute LC50 <10 mg/l Fish 96 hours

Persistence and degradability

Product/ingredient name Aquatic half-life Photolysis Biodegradability
dicopper oxide - - Not readily
xylene - - Readily
ethylbenzene - - Readily
zinc oxide - - Not readily
hydrocarbons, C9, aromatics - - Not readily

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
xylene 3.12 8.1 to 25.9 low
colophony 1.9 to 7.7 - high
zineb 1.3 - low
ethylbenzene 3.6 - low
zinc oxide - 28960 high
1-methoxy-2-propanol <1 - low
hydrocarbons, C9, aromatics - 10 to 2500 high

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Vapour from product
residues may create a highly flammable or explosive atmosphere inside the
container. Do not cut, weld or grind used containers unless they have been cleaned
thoroughly internally. Avoid dispersal of spilt material and runoff and contact with
soil, waterways, drains and sewers.
Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 11/13
SeaForce Shield

Section 14. Transport information

ADR/RID IMDG IATA
UN number UN1263 UN1263 UN1263

UN proper Paint Paint. Marine pollutant Paint

shipping name (dicopper oxide)
Transport hazard 3 3 3
class(es)

Packing group III III III

Environmental Yes. Yes. Yes. The environmentally
hazards hazardous substance mark is
not required.
Additional - The marine pollutant mark is The environmentally
information not required when transported hazardous substance mark
in sizes of ≤5 L or ≤5 kg. may appear if required by
Emergency schedules F-E, other transportation
S-E regulations.

Additional information
ADR/RID : The environmentally hazardous substance mark is not required when transported in
sizes of ≤5 L or ≤5 kg.
Hazard identification number 30
Tunnel code (D/E)
IMDG : The marine pollutant mark is not required when transported in sizes of ≤5 L or ≤5 kg.
Emergency schedules F-E, S-E
IATA : The environmentally hazardous substance mark may appear if required by other
transportation regulations.
Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.

Transport in bulk according : Not available.

to IMO instruments

Section 15. Regulatory information

Safety, health and : No known specific national and/or regional regulations applicable to this product
environmental regulations (including its ingredients).
specific for the product
International regulations
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants

Not listed.

UNECE Aarhus Protocol on POPs and Heavy Metals

Not listed.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 12/13
SeaForce Shield

Section 16. Other information

History
Date of printing : 27.01.2023
Date of issue/Date of : 27.01.2023
revision
Date of previous issue : 27.01.2023
Version : 1.03
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
References : Not available.
Indicates information that has changed from previously issued version.
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are
often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the
product itself. Minor product variations may be implemented in order to comply with local requirements.
Jotun reserves the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their
needs and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United
Kingdom) version will prevail.

Date of issue/Date of revision : 27.01.2023 Date of previous issue : 27.01.2023 Version : 1.03 13/13