STRUCTURAL TECHNICAL REPORT FOR STAIR CASE C

AT LEVEL LB1/ GF / FIRST PART - B

 STRUCTURAL TECHNICAL REPORT FOR STAIRCASE C
INDEX

Contents Page No.s

1) INTRODUCTION 3

2) DESIGN CRITERIA 3

3) MATERIALS 4

4) STRUCTURAL SYSTEM 4

5) COMPUTER PROGRAMS 4

6) SUBMITTED CALCULATIONS 5

7) REFERNCE DWGS ATTACHED. 6

1) INTRODUCTION

This report covers the structural calculation for STAIRCASE C 2.14

2) DESIGN CRITERIA

2.1) Codes of Practice and standards:

Structural design and analysis, Properties and testing of materials shall comply with the the
latest available edition of following codes and standards:

 AISC manual of steel construction.

 UBC uniform building code.

 AISC American institute of steel construction

 AWS American welding society.

 ASTM American society for testing and materials.

 AISC engineering for steel construction, a source book of connections

2.2) Loads

The Self Weight of structure is calculated by Safe Program and other loads are taken as
followings

2.3.1) Dead Loads

Finishing & Steel plate Loads 2.0Kn/m2

Total Dead load Considered. 2.0Kn/m2

2.3.2) Live Loads 5.0 Kn/m2

( Staircases)

2.3.3) Load Combinations

1.0 DL + 1.0 LL
3) MATERIAL PROPERTIES

Compressive strength of concrete for design purposes (fcd’) = 28 N/mm2

Minimum yield strength of reinforcing steel bars (fy) = 420 N/mm2
Minimum yield strength of Structural steel (fy) = 450 N/mm2
Cable should be designed to carry capacity of 100Kn
Hot rolled steel shapes and for columns and beams shall be in accordance with
ASTM A-36.

Anchor bolts in accordance with ASTM A-325

High strength bolts in accordance with ASTM A-325 OR A-490.

Metal decking in accordance with ASTM A-607 grade 50.

Welds: ASTM E70XX low hydrogen electrodes, conforming to AWS D1.1. Structural
welds.

4) STRUCTURAL SYSTEM CONSIDERED &

For steel structure allowable stress design method of the AISC code will be used.

The geometric 3D model was made for stringer beams

Followings are assumed as per the normal practices:

10mm full weld both sides are to be made at every intersection of members

The Cable can carry load of 100kn with suitable diameter And material

The Turnbuckle or connecters to the cable and stringer beams are to be manufactured

With a capacity of 100KN

The Bolts used are all M16 with suitable lengths as per site

And Bolted connections are designed to carry max shear force and moments with allowable

Bolt shear capacity assumed as 2243 kgs (M16)

5) COMPUTER PROGRAMS

Staad pro & Custom made Excel sheets

6) SUBMITTED CALCULTIONS

Input files for Staad program ( Stair C.Std) attached in CD and folloeings are attached
for clarifications

A) GEOMETRICS

B) DEAD LOADS & LIVE LOADS

D) SHEAR FORCE & BENDING MOMENTS

C) DEFLECTION MAX

D) SUPPORT REACTIONS

E) CODE CHECK FOR THE MEMBERS

F) INPUT AND OUT PUT FILE

G) ANCHOR BOLT CALCULATIONS

 Job No Sheet No Rev
1
Part
Software licensed to k
Job Title Ref

By Date03-May-11 Chd

Client File Stair_C.std Date/Time 04-May-2011 14:20

0.781

0.293

0.141
0.294 0.142
0.141 0.186
0.507 0.181
0.15
0.158
0.0826 0.141 0.231
0.16
0.508 0.171
0.199
0.199

0.307

0.267

0.347
0.288
0.153
0.154
0.0858 0.263
0.278
0.368
0.777 0.0755 0.216
0.0746
0.202 0.306 0.158
0.247
0.0684
0.217 0.157
0.174
0.206

Z 0.192
X 0.299
0.184
0.171 0.257
0.315 0.31
0.171 0.245
0.248

0.166

0.0984

0.0959 Load 3

Print Time/Date: 04/05/2011 14:43 STAAD.Pro for Windows Release 2006 Print Run 1 of 1
 Wednesday, May 04, 2011, 02:46 PM
PAGE NO. 1

****************************************************
* *
* STAAD.Pro *
* Version 2006 Bld 1002.US *
* Proprietary Program of *
* Research Engineers, Intl. *
* Date= MAY 4, 2011 *
* Time= 14:35:41 *
* *
* USER ID: k *
****************************************************

1. STAAD SPACE DXF IMPORT OF STAIRC.DXF

INPUT FILE: Stair_C.STD
2. SET Z UP

**WARNING- THE FOLLOWING COMMANDS SHOULD NOT BE USED WHEN THE SET Z UP
IS ALSO ENTERED: FLOOR LOAD , AREA LOAD , Nonlinear Cable Analysis
GENERATION of SPRING SUPPORTS for ELASTIC MAT FOUNDATIONS

3. START JOB INFORMATION

4. ENGINEER DATE 03-MAY-11
5. END JOB INFORMATION
6. INPUT WIDTH 79
7. UNIT MMS NEWTON
8. JOINT COORDINATES
9. 1 -1 0 0; 5 4191.81 9.28025E-005 1337; 6 4191.81 750 1337; 7 4191.81 1500 1337
10. 10 2.13913E-009 1500 3.2E-015; 11 2400 1500 1337; 13 5400 1500 1337
11. 14 7800 1500 2675; 15 9430.73 1500 2675; 16 9606.78 3512.22 2675
12. 17 9299.5 6.83147E-005 2675; 18 7800 7.53997E-005 2675
13. 20 5400 9.15557E-005 1337; 21 2400 9.20898E-005 1337; 27 8200 -99.9999 2675
14. 28 8200 7.35097E-005 2675; 29 9195.88 -99.9999 2675
15. 30 9195.88 6.88043E-005 2675; 33 9518.98 3627.37 2675; 34 9503.33 3528.6 2675
16. 35 8126.46 3746.68 2675; 36 7891.8 2265.14 2675; 37 2731.13 3082.51 5350
17. 38 2936.64 4568.66 5350; 39 9475.72 2014.28 2675; 40 7990.57 2249.5 2675
18. 41 7925 1500 2675; 65 8200 -99.9999 8550; 67 2537.17 0.00037998 5350
19. 68 2625.17 1500 5350; 69 7800 1500 8550; 70 7800 0.00037998 8550
20. 71 7925 1500 8550; 72 7990.57 2249.5 8550; 73 7891.8 2265.14 8550
21. 74 9475.72 2014.28 8550; 75 9430.73 1500 8550; 76 9299.5 0.00037998 8550
22. 77 9606.78 3512.22 8550; 78 9503.33 3528.6 8550; 79 8126.46 3746.68 8550
23. 80 2936.64 4568.66 11750; 81 2731.13 3082.51 11750; 82 8200 0.00037998 8550
24. 83 9518.98 3627.37 8550; 84 8536.71 3782.95 8550; 85 8521.07 3684.18 8550
25. 87 9195.88 -100 8550; 88 9195.88 0.00037998 8550; 89 8536.71 3782.95 2675
26. 90 8521.07 3684.18 2675; 92 4191.81 750 0; 93 9518.98 3627.37 16900
27. 95 8536.71 3782.95 16900; 97 8200 -99.9999 16900; 99 9195.88 -100 16900
28. MEMBER INCIDENCES
29. 3 5 6; 4 6 7; 6 10 11; 7 11 7; 8 7 13; 9 13 14; 10 14 41; 11 16 39; 12 14 18
30. 13 13 20; 14 11 21; 15 1 10; 16 1 21; 17 21 5; 18 5 20; 19 20 18; 20 18 28
31. 21 27 28; 22 29 30; 24 33 34; 25 16 34; 26 35 36; 27 36 37; 28 37 38; 29 38 35
32. 30 36 40; 31 40 41; 62 67 68; 63 68 69; 64 69 70; 65 70 67; 66 71 72; 67 73 72
33. 68 69 71; 69 76 75; 71 79 80; 72 80 81; 73 81 73; 74 73 79; 75 70 82; 76 83 78
34. 77 84 85; 78 65 82; 79 87 88; 80 79 85; 86 27 65; 87 29 87; 88 33 83; 90 89 90

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 1 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 2

35. 91 89 84; 93 92 6; 94 72 74; 95 71 75; 96 88 76; 97 82 88; 98 78 77; 99 85 78

36. 100 65 97; 101 87 99; 102 83 93; 103 84 95; 104 30 17; 105 28 30; 106 90 35
37. 107 34 90; 108 41 15; 109 40 39; 110 15 17; 111 39 15; 112 74 77; 113 75 74
38. DEFINE MATERIAL START
39. ISOTROPIC STEEL
40. E 205000
41. POISSON 0.3
42. DENSITY 7.68195E-005
43. ALPHA 1.2E-005
44. DAMP 0.03
45. END DEFINE MATERIAL
46. MEMBER PROPERTY EUROPEAN
47. 3 4 6 TO 9 11 16 TO 20 25 27 29 30 63 65 67 TO 69 71 73 75 80 93 TO 99 104 -
48. 105 TO 107 109 TO 113 TABLE ST TUB3002008
49. 21 22 24 76 TO 79 90 TABLE ST IPN200
50. 10 12 TO 15 26 28 31 62 64 66 72 74 108 TABLE ST UPN200
51. UNIT METER KN
52. MEMBER PROPERTY
53. 86 TO 88 91 100 TO 103 PRIS YD 0.032
54. UNIT MMS NEWTON
55. CONSTANTS
56. BETA 180 MEMB 28 62 66 74
57. MATERIAL STEEL ALL
58. SUPPORTS
59. 93 95 97 99 FIXED BUT FX FY MX MY MZ
60. 1 10 37 38 67 68 80 81 PINNED
61. 92 PINNED
62. MEMBER CABLE
63. 86 TO 88 91 100 TO 103 TENSION 0
64. LOAD 1 LOADTYPE DEAD TITLE DEAD LOAD
65. MEMBER LOAD
66. 6 TO 10 16 TO 20 25 27 29 30 63 65 67 68 71 73 75 80 94 TO 99 104 TO 108 -
67. 109 UNI GZ -2
68. SELFWEIGHT Z -1
69. LOAD 2 LOADTYPE LIVE TITLE LIVE LOAD
70. MEMBER LOAD
71. 6 TO 10 16 TO 20 25 27 29 30 63 65 67 68 71 73 75 80 94 TO 99 104 TO 108 -
72. 109 UNI GZ -3.75
73. LOAD COMB 3 COMBINATION LOAD CASE 3
74. 1 1.0 2 1.0
75. PERFORM ANALYSIS

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 56/ 71/ 13

ORIGINAL/FINAL BAND-WIDTH= 49/ 7/ 44 DOF
TOTAL PRIMARY LOAD CASES = 2, TOTAL DEGREES OF FREEDOM = 305
SIZE OF STIFFNESS MATRIX = 14 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.2/ 130041.9 MB

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 2 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 4

STAAD.PRO CODE CHECKING - (AISC 9TH EDITION)

********************************************

ALL UNITS ARE - NEWT MMS (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

3 ST TUB3002008 (EUROPEAN SECTIONS)

PASS AISC- H1-3 0.315 3
2108.09 C 31001650.00 1831251.62 750.00
4 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.257 3
2592.42 T 24717058.00 1831251.62 0.00
6 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.166 3
43950.66 C 11866508.00 1031289.12 2747.28
7 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.171 3
44164.86 C 11994323.00 1450101.12 1791.81
8 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.299 3
42008.24 C 21257222.00 4898817.50 0.00
9 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.206 3
48365.88 C -14316138.00 2069210.12 228.98
10 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.247 3
40264.00 C -3495761.75 -211643.95 125.00
11 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.263 3
6581.69 C -10250675.00 12547847.00 1503.66
12 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.217 3
2737.74 T 1672317.50 -657737.56 0.00
13 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.184 3
1102.63 C -671998.44 -655392.94 0.00
14 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.171 3
118.81 T 4759251.50 -15463.16 0.00
15 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.096 3
0.00 T 765589.31 -287297.66 0.00
16 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.098 3
19870.19 T -8572284.00 -74941.73 1832.11
17 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.245 3
17131.26 T 23715238.00 646257.31 1791.81

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 4 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 5

ALL UNITS ARE - NEWT MMS (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

18 ST TUB3002008 (EUROPEAN SECTIONS)

PASS AISC- H2-1 0.310 3
7639.07 T 24259998.00 5934148.00 0.00
19 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.192 3
8533.80 T -14611764.00 -3735870.75 2747.77
20 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.174 3
5894.82 T -14611471.00 -2495026.75 0.00
25 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.153 3
14269.35 C 4512384.00 7682616.00 104.74
26 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.368 3
5214.66 T -4520531.00 -868738.94 0.00
27 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.278 3
56079.76 T -23612608.00 661851.31 2934.97
28 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.347 3
0.00 T -380901.56 1389019.88 0.00
29 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.288 3
16629.81 C -28324224.00 367315.66 2948.11
30 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.075 3
48894.20 T 1405953.50 -1469775.12 0.00
31 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.202 3
4303.37 T -3638192.50 321546.94 0.00
62 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.777 3
0.00 T -2784080.25 -2827072.50 1502.58
63 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.307 3
71907.42 C -22157782.00 -1275117.50 3042.16
64 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.508 3
4196.88 C 4121418.00 -1465072.25 0.00
65 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.267 3
26011.77 T -24335148.00 1350897.00 2566.39
66 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.083 3
2348.46 C -1585168.62 265189.72 0.00

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 5 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 6

ALL UNITS ARE - NEWT MMS (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

67 ST TUB3002008 (EUROPEAN SECTIONS)

PASS AISC- H2-1 0.158 3
54441.83 T 4841912.50 -5108300.00 0.00
68 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.160 3
59618.80 C 5448981.00 -4453621.00 0.00
69 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.231 3
7226.12 T -2368430.50 15731039.00 1505.73
71 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.293 3
19247.32 C -26319220.00 1942923.38 2563.43
72 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.781 3
0.00 T 2271398.25 2918108.00 1500.29
73 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.294 3
65297.94 T -22940368.00 -1745901.88 3063.52
74 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.507 3
1305.98 T 5809513.50 -1258942.75 1500.01
75 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.199 3
18712.95 T 12090320.00 -5425888.00 400.00
80 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.141 3
13553.11 C 6679086.50 -5218221.50 399.53
93 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.248 3
83571.78 C 9807658.00 -6284592.50 1337.00
94 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.150 3
55327.39 T 4186254.50 -4875283.50 0.00
95 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.141 3
60134.89 C 3911711.00 -3875079.00 0.00
96 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.171 3
18712.95 T 610744.38 -11601315.00 103.62
97 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.199 3
18712.95 T 12090320.00 -5425888.00 0.00
98 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.141 3
13552.98 C 2343541.25 -8366695.00 104.74

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 6 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 7

ALL UNITS ARE - NEWT MMS (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

99 ST TUB3002008 (EUROPEAN SECTIONS)

PASS AISC- H1-3 0.142 3
13553.12 C 6678954.00 -5218221.50 0.00
104 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.068 3
5894.82 T -2654513.25 -2988038.50 103.62
105 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.157 3
5894.82 T -12607773.00 -2626540.50 0.00
106 ST TUB3002008 (EUROPEAN SECTIONS)
PASS SHEAR -Y 0.086 3
14269.61 C 1478729.25 2113456.25 0.00
107 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.154 3
14269.63 C 4512318.50 7682616.00 0.00
108 ST UPN200 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.306 3
40087.23 C -3484803.50 -306839.75 0.00
109 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.076 3
48041.59 T -2111969.00 -1084991.88 1002.44
110 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.158 3
841.29 T -8850495.00 -5811046.00 0.00
111 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.216 3
2976.40 C -6826893.00 11590494.00 0.00
112 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H1-3 0.186 3
3802.59 C -3486390.00 -11662565.00 0.00
113 ST TUB3002008 (EUROPEAN SECTIONS)
PASS AISC- H2-1 0.181 3
1881.54 T -2605629.50 12012918.00 0.00

79. UNIT METER KN

80. PARAMETER 2
81. CODE AISC
82. SELECT WELD MEMB 29 64 65 71 75 90 106 107

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 7 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 8

STAAD.Pro WELD DESIGN

*********************

ALL UNITS ARE - METE KN

MEMBER LOCATION/ WELD TYPE/ WELD SIZE/ COMB STRESS/

LOADING HOR STRESS VERT STRESS DIR STRESS
=====================================================================

29 STA 1 5 MM 10973.12
3 9619.15 267.48 5273.50

29 END 1 5 MM 29838.02
3 8272.45 267.48 28667.09

MEMBER 64 CANNOT BE DESIGNED AT STA

Calculated welds size exceeds welds maximum allowable thickness.

No solution can be found for current member size.

MEMBER 64 CANNOT BE DESIGNED AT END

Calculated welds size exceeds welds maximum allowable thickness.

No solution can be found for current member size.
65 STA 1 5 MM 24028.40
3 10118.09 1353.99 21752.12

65 END 1 5 MM 15801.93
3 9974.82 1353.99 12180.75

71 STA 1 5 MM 28249.47
3 9295.35 1052.57 26655.61

71 END 1 5 MM 14136.63
3 9720.12 1052.57 10210.57

75 STA 1 5 MM 23815.70
3 18452.51 5005.31 14199.97

75 END 1 5 MM 55122.79
3 19784.22 5005.31 51205.99

90 STA 2 5 MM 14601.79
3 14601.79 0.00 0.00

90 END 2 5 MM 92546.71
3 14586.17 0.00 91390.03

106 STA 1 5 MM 23425.66

3 19010.54 6282.54 12161.04

106 END 1 5 MM 31178.20

3 17680.39 6282.54 24900.07

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 8 of 11

 Wednesday, May 04, 2011, 02:46 PM
DXF IMPORT OF STAIRC.DXF -- PAGE NO. 9

STAAD.Pro WELD DESIGN

*********************

ALL UNITS ARE - METE KN

MEMBER LOCATION/ WELD TYPE/ WELD SIZE/ COMB STRESS/

LOADING HOR STRESS VERT STRESS DIR STRESS
=====================================================================

107 STA 1 5 MM 34604.94

3 6115.77 3865.73 33840.14

107 END 1 5 MM 13088.75

3 2913.20 3865.73 12160.78

************* END OF TABULATED RESULTS FOR WELD DESIGN *************

83. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= MAY 4,2011 TIME= 14:35:41 ****

C:\Documents and Settings\User\Desktop\Steel Staircase C\Stair_C.anl Page 9 of 11

 Company: Page 1 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/4/2011
Specifier's comments:

Anchor type and size: HST-R-M20

Effective embedment depth: h ef = 101 mm
Material: A4
Approval No.: ETA - 98/0001
Issued/Valid: 12.02.2008 / 19.02.2013
Proof: design method ETAG No. 001 Annex C
Stand-off installation: eb = 0 mm (no stand-off) ; t = 20 mm
Anchor plate: S235 (ST37) ; lx x ly x t = 400 x 400 x 20 mm
Base material: uncracked concrete C30/37, fcc = 37.00 N/mm² ; h = 10000 mm
Reinforcement: reinforcement spacing >= 150 mm
no longitudinal edge reinforcement
Anchor

Geometry [mm]
plan view section A
y z
x
t=20
h ef =101
>10h ef

lx = 400
section B

3 4 x
250

section B z
y
1 2
>10h ef

h = 10000

>10h ef 250 >10h ef

ly = 400
section A

Loading
Design loads [kN, Nm]
Resulting loads [kN, Nm]
N 100.00
Vx 0.00
Vy 0.00
Mx 0.00
My 0.00
Mz 0.00
Eccentricity (structural section) [mm]
ex = 0 ; e y = 0

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 2 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/4/2011

Load case (Design loads):

Anchor reactions [kN]
Tension force: (+Tension, -Compression)

Anchor Tension force Shear force

1 25.00 0.00
2 25.00 0.00
3 25.00 0.00
4 25.00 0.00

max. concrete compressive strain [ ‰]: 0.00

max. concrete compressive stress [N/mm²]: 0.00
resulting tension force [kN]: 100.00
resulting compression force [kN]: 0.00

Tension load (ETAG, Annex C, Section 5.2.2)

Design values [kN]

Proof Load Capacity Utilisation βN [%] Status
Steel failure 25.00 63.01 40 OK
Pull-out failure 25.00 24.33 103 not recommended
Concrete cone failure 100.00 98.72 102 not recommended
Splitting failure 100.00 148.07 68 OK

Steel failure
h h
N Rk,s [kN ] γM,s N Rd,s [kN ] N Sd [kN ]
109.00 1.730 63.01 25.00

Pull-out failure
h h
N Rk,p [kN ] ψc γM,p N Rd,p [kN ] N Sd [kN ]
30.00 1.217 1.500 24.33 25.00

Concrete cone failure

2 0 2
A c,N [mm ] A c,N [mm ] c cr,N [mm ] scr,N [mm ]
305809.0 91809.0 152 303

ψ ec1,N ψ ec2,N ψ re,N ψ s,N ψ ucr,N

1.000 1.000 1.000 1.000 1.000
0
N Rk,c [kN ] γM,c N Rd,c [kN ] N Sd [kN ]
44.45 1.500 98.72 100.00

Splitting failure
2 0 2
A c,N [mm ] A c,N [mm ] c cr,sp [mm ] scr,sp [mm ]
305809.0 91809.0 152 303

ψ s,N ψ ec1,N ψ ec2,N ψ re,N ψ ucr,N ψ h,sp

1.000 1.000 1.000 1.000 1.000 1.500
0
N Rk,c [kN ] γM,sp N Rd,sp [kN ] N Sd [kN ]
44.45 1.500 148.07 100.00

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 3 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/4/2011

Warnings
The concrete edge capacity is calculated according to CEN Draft 7, Oct. 2003
Although the user chose uncracked concrete the calculation is performed for a cracked concrete because of resulting load is larger
than 60.00 kN

Fastening does not meet the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 4 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/4/2011

Anchorplate, steel: S235 (ST37)

Section type: - no profile (0 x 0 x 0)
Hole diameter d f = 22 mm
Recommended plate thickness: not calculated

75.0
200.0
3 4

200.0

1 2
75.0

75.0 75.0
200.0 200.0

Coordinates Anchor [mm] Anchorplate [mm]

Anchor x y Anchor x y x y x y
1 -125 -125 3 -125 125 -200 200 200 -200
2 125 -125 4 125 125 200 200 -200 -200

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 1 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/8/2011
Specifier's comments:

Anchor type and size: HST-R-M20

Effective embedment depth: h ef = 101 mm
Material: A4
Approval No.: ETA - 98/0001
Issued/Valid: 12.02.2008 / 19.02.2013
Proof: design method ETAG No. 001 Annex C
Stand-off installation: eb = 0 mm (no stand-off) ; t = 20 mm
Anchor plate: S235 (ST37) ; lx x ly x t = 400 x 400 x 20 mm
Base material: uncracked concrete C30/37, fcc = 37.00 N/mm² ; h = 10000 mm
Reinforcement: reinforcement spacing >= 150 mm
no longitudinal edge reinforcement
Anchor

Geometry [mm]
plan view section A
y z
x
t=20
h ef =101
>10h ef

lx = 400
section B

3 4 x
250

section B z
y
1 2
>10h ef

h = 10000

>10h ef 250 >10h ef

ly = 400
section A

Loading
Design loads [kN, Nm]
Resulting loads [kN, Nm]
N 0.00
Vx 100.00
Vy 0.00
Mx 0.00
My 0.00
Mz 0.00
Eccentricity (structural section) [mm]
ex = 0 ; e y = 0

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 2 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/8/2011

Load case (Design loads):

Anchor reactions [kN]
Tension force: (+Tension, -Compression)

Anchor Tension force Shear force

1 0.00 25.00
2 0.00 25.00
3 0.00 25.00
4 0.00 25.00

max. concrete compressive strain [ ‰]: 0.00

max. concrete compressive stress [N/mm²]: 0.00
resulting tension force [kN]: 0.00
resulting compression force [kN]: 0.00

Shear load (ETAG, Annex C, Section 5.2.3)

Design values [kN]

Proof Load Capacity Utilisation βV [%] Status
Steel failure (without lever 25.00 55.56 45 OK
arm)
Pryout failure 25.00 49.36 51 OK

Steel failure (without lever arm)

h h
V Rk,s [kN ] γM,s V Rd,s [kN ] V Sd [kN ]
80.00 1.440 55.56 25.00

Pryout failure
2 0 2
A c,N [mm ] A c,N [mm ] c cr,N [mm ] scr,N [mm ] k-factor
305809.0 91809.0 152 303 2.000

ψ ec1,N ψ ec2,N ψ s,N ψ re,N ψ ucr,N

1.000 1.000 1.000 1.000 1.000
0 h h
N Rk,c [kN ] γM,c,p V Rd,c1 [kN ] V Sd [kN ]
44.45 1.500 49.36 25.00

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 3 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/8/2011

Displacements (highest loaded anchor)

Short term loading:

h
N Sk = 0.00 [kN] δN = 0.000 [mm]
h
V Sk = 18.52 [kN] δV = 1.157 [mm]
δNV = 1.157 [mm]
Long term loading:
h
N Sk = 0.00 [kN] δN = 0.000 [mm]
h
V Sk = 18.52 [kN] δV = 1.713 [mm]
δNV = 1.713 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear
displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance
hole tolerances are not included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

Proof of the transmission of the anchor loads to the supports

Transmission of the anchor loads into the concrete
Checking the transfer of loads into the base is required in accordance with ETAG Section 7.1!
Shear resistance of base material
Shear resistance of the base material must be checked according to relevant approval or Eurocode 2/ BS8110 etc.

Warnings
The concrete edge capacity is calculated according to CEN Draft 7, Oct. 2003
Although the user chose uncracked concrete the calculation is performed for a cracked concrete because of resulting load is larger
than 60.00 kN

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 Company: Page 4 of 4
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.11.20 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 5/8/2011

Anchorplate, steel: S235 (ST37)

Section type: - no profile (0 x 0 x 0)
Hole diameter d f = 22 mm
Recommended plate thickness: not calculated

75.0
200.0
3 4

200.0

1 2
75.0

75.0 75.0
200.0 200.0

Coordinates Anchor [mm] Anchorplate [mm]

Anchor x y Anchor x y x y x y
1 -125 -125 3 -125 125 -200 200 200 -200
2 125 -125 4 125 125 200 200 -200 -200

Input data and results must be checked for agreement with the existing conditions and for plausibility!

PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan