0% found this document useful (0 votes)
74 views5 pages

Bistable Multivibrator

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
74 views5 pages

Bistable Multivibrator

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Bistable Multivibrator

Bistable Multivibrator

Bistable Multivibrators operate in a similar fashion to flip-flops producing one of two stable
outputs which are the complement of each other

The Bistable Multivibrator is another type of two state device similar to the
Monostable Multivibrator we looked at in the previous tutorial but the difference this
time is that BOTH states are stable.
Bistable Multivibrators have TWO stable states (hence the name: “Bi” meaning two)
and maintain a given output state indefinitely unless an external trigger is applied
forcing it to change state.
The bistable multivibrator can be switched over from one stable state to the other by
the application of an external trigger pulse thus, it requires two external trigger pulses
before it returns back to its original state. As bistable multivibrators have two stable
states they are more commonly known as Latches and Flip-flops for use in sequential
type circuits.
The discrete Bistable Multivibrator is a two state non-regenerative device
constructed from two cross-coupled transistors operating as “ON-OFF” transistor
switches. In each of the two states, one of the transistors is cut-off while the other
transistor is in saturation, this means that the bistable circuit is capable of remaining
indefinitely in either stable state.
To change the bistable over from one state to the other, the bistable circuit requires a
suitable trigger pulse and to go through a full cycle, two triggering pulses, one for
each stage are required. Its more common name or term of “flip-flop” relates to the
actual operation of the device, as it “flips” into one logic state, remains there and then
changes or “flops” back into its first original state. Consider the circuit below.

Bistable Multivibrator Circuit

The Bistable Multivibrator circuit above is stable in both states, either with one
transistor “OFF” and the other “ON” or with the first transistor “ON” and the second
“OFF”. Lets suppose that the switch is in the left position, position “A”. The base of
transistor TR1 will be grounded and in its cut-off region producing an output at Q.
That would mean that transistor TR2 is “ON” as its base is connected to Vcc through
the series combination of resistors R1 and R2. As transistor TR2 is “ON” there will be
zero output at Q, the opposite or inverse of Q.
If the switch is now move to the right, position “B”, transistor TR2 will switch “OFF”
and transistor TR1 will switch “ON” through the combination of
resistors R3 and R4 resulting in an output at Q and zero output at Q the reverse of
above. Then we can say that one stable state exists when transistor TR1 is “ON”
and TR2 is “OFF”, switch position “A”, and another stable state exists when
transistor TR1 is “OFF” and TR2 is “ON”, switch position “B”.
Then unlike the monostable multivibrator whose output is dependent upon
the RC time constant of the feedback components used, the bistable multivibrators
output is dependent upon the application of two individual trigger pulses, switch
position “A” or position “B”.
So Bistable Multivibrators can produce a very short output pulse or a much longer
rectangular shaped output whose leading edge rises in time with the externally applied
trigger pulse and whose trailing edge is dependent upon a second trigger pulse as
shown below.

Bistable Multivibrator Waveform

Manually switching between the two stable states may produce a bistable
multivibrator circuit but is not very practical. One way of toggling between the two
states using just one single trigger pulse is shown below.

Sequential Switching
Switching between the two states is achieved by applying a single trigger pulse which
in turn will cause the “ON” transistor to turn “OFF” and the “OFF” transistor to turn
“ON” on the negative half of the trigger pulse. The circuit will switch sequentially by
applying a pulse to each base in turn and this is achieved from a single input trigger
pulse using a biased diodes as a steering circuit.
Then on the application of a first negative pulse switches the state of each transistor
and the application of a second pulse negative pulse resets the transistors back to their
original state acting as a divide-by-two counter. Equally, we could remove the diodes,
capacitors and feedback resistors and apply individual negative trigger pulses directly
to the transistor bases.
Bistable Multivibrators have many applications producing a set-reset, SR flip-flop
circuit for use in counting circuits, or as a one-bit memory storage device in a
computer. Other applications of bistable flip-flops include frequency dividers because
the output pulses have a frequency that are exactly one half ( ƒ/2 ) that of the trigger
input pulse frequency due to them changing state from a single input pulse. In other
words the circuit produces Frequency Division as it now divides the input frequency
by a factor of two (an octave).

TTL/CMOS Bistable Multivibrators


As well as producing a bistable multivibrator from individual discrete components
such as transistors, we can also construct bistable circuits using commonly available
integrated circuits. The following circuit shows how a basic bistable multivibrator
circuit can be constructed using just two 2-input Logic “NAND” Gates.

NAND Gate Bistable Multivibrator


The circuit above shows us how we can use two NAND gates connected together to
form a basic bistable multivibrator. This type of bistable circuit is also known as a
“Bistable Flip-flop”. The manually controlled bistable multivibrator is activated by
the single-pole double-throw switch (SPDT) to produce a logic “1” or a logic “0”
signal at the output.
You may have noticed that this circuit looks a little familiar, and you would be right!.
This type of bistable switching circuit is more commonly called a SR NAND Gate
Flip-flop being almost identical to the one we looked at back in the sequential logic
tutorials. In that particular tutorial we saw that this type of NAND gate bistable makes
an excellent “switch debounce” circuit allowing only one switching action to control
its output.
In the next tutorial about Multivibrators, we will look at one that has NO stable states
because it is continually switching over from one stable state to the other. This type of
multivibrator circuit is called an Astable Multivibrator also known by their more
common name of “fee-running oscillator”.

You might also like