FOUR - User Guide - V1.0

Download as pdf or txt
Download as pdf or txt
You are on page 1of 38

User Guide

Powered by Serato DJ Pro


Table of Contents

INTRODUCTION.......................................................... 4

Box Contents ........................................................................................ 4

Support ................................................................................................... 4

Product Registration .......................................................................... 4

SETUP ........................................................................... 5

Connection Diagram .......................................................................... 5

FEATURES ................................................................... 6

Top Panel ............................................................................................... 6

Deck Controls ........................................................................................................ 6

Performance Pads ............................................................................................... 8

Jog Wheel Display ............................................................................................. 10

FX Section .............................................................................................................. 11

Mixer Controls ...................................................................................................... 12

Front Panel .......................................................................................... 14

Rear Panel ............................................................................................ 15

2
OPERATION ............................................................... 16

Pad Display ......................................................................................... 16

Pad Modes ............................................................................................ 17

Hot Cue ............................................................................................................... 17

Roll........................................................................................................................19

Sampler ...............................................................................................................19

Stems ................................................................................................................... 18

Pitch Play ........................................................................................................... 18

Saved Loops ..................................................................................................... 18

Scratch Bank ................................................................................................... 20

Slicer Mode ...................................................................................................... 20

APPENDIX .................................................................. 21

Internal Hardware Effects ............................................................... 21

System Menu ...................................................................................... 33

Technical Specifications ................................................................. 35

Trademarks & Licenses ................................................................... 37

3
INTRODUCTION

Thank you for purchasing the FOUR. At Rane, performance and reliability mean as
much to us as they do to you. That’s why we design our equipment with only one
thing in mind—to make your performance the best it can be.

Box Contents
FOUR
(2) USB 2.0 Cables (2 m)
IEC Power Cable (region-specific)
DeoxIT® Fader Lube (2 mL)
Quickstart Guide
Serato Pitch N Time DJ Expansion Pack Voucher
Rane Sticker Sheet
Safety & Warranty Pamphlet

Support
For the latest information about this product (documentation, technical
specifications, system requirements, compatibility information, etc.) and product
registration, visit rane.com.
For additional product support, visit rane.com/support.

Product Registration
Your product may include exclusive software and/or promotions which can only be
accessed by registering your new product on the Rane website.

To check eligibility and access the available content, please register your product by
following the instructions below:
1. Visit rane.com and click Account.
2. Click Sign In to access your existing account, or create a new account.
3. Once signed in, click Register New Product.
4. Enter the product serial number into the box and click Check Serial.
5. Complete the form and click Register Your Product.
6. Upon successful registration, any applicable software downloads, exclusive
content, and promotional offers will be shown in your account.

4
SETUP

1. Make sure you have downloaded and installed the latest version of your DJ
software and driver from rane.com/downloads.
Note: Driver installation is required to connect FOUR with macOS or Windows
computers.
2. Place FOUR on a flat, stable surface.
3. While the power is switched off, plug the included power cable into FOUR first,
then plug the cable into a power outlet.
Connect audio input sources (microphones, turntables, etc.) to FOUR.
Connect audio output devices (headphones, power amplifiers, loudspeakers, etc.)
to FOUR.
4. Connect all devices to power outlets, and power on the devices in proper order:
• When starting a session, turn on (1) input sources, (2) FOUR, (3) output
devices.
• When ending a session, turn off (1) output devices, (2) FOUR, (3) input
sources.
5. Use a standard USB cable (included) to connect one of the USB Ports to an
available USB port on your computer or a powered hub connected to the
computer.
6. Open Serato DJ Pro and go!
For more information on how to use Serato DJ Pro with the FOUR, please visit
support.serato.com.

Connection Diagram
Items not listed under Introduction > Box Contents are sold separately.

Booth
Monitors
Computer Turntable

Headphones

Microphone

Power

Main Monitors

5
FEATURES

Top Panel

Deck Controls
1. Deck Layer Section: Press to select 11 12 3
the active deck layer. Decks 1 & 3 9 10 2
are on the left deck. Decks 2 & 4
are on the right deck.
17
2. Scroll/Load: Turn the encoder to
navigate through the software. 1
Push to load a song to the active
deck layer. Press this knob twice
quickly to load the same track to
6
both decks (“instant doubles”). 8 7
3. Back/Load Prep: Press this button
to move back through levels of
library organization. 4
Press and hold Shift and press this
button to load the currently
selected track to the Prepare crate. 13
4. Pitch Fader: Move this fader to
adjust the speed (pitch) of the 5
track. You can adjust its total range 15
with the pitch Range button.
5. Pitch Bend -/+: Press and hold one 14
of these buttons to momentarily
reduce or increase (respectively)
the speed of the track.
6. Range / Keylock: Press this button to adjust the range of the Pitch Fader to
±8%, ±16%, and ±50%.
Press and hold Shift and press this button to activate or deactivate Keylock: the
key of the song will lock to whatever position the pitch fader is at when Keylock
is activated. This feature allows you to change the speed of the song without
changing the key.
7. Jog Wheel: This 8” capacitive touch jog wheel is used to control song position,
scratching, and pitch bend (when platter touch is turned off).
Press and hold Shift while rotating the platter to seek through the timeline of the
track loaded to the deck.
8. Jog Wheel Display: This 2” color display provides info for Needle position,
Track progress ring, Beat Jump Length, BPM, Pitch Range, Pitch Percentage,
Overview waveform with playhead position and hot cue markers, Song Key,
Song Time (remaining/elapsed), Loop Length, and Focus Deck.
Tip: For the best play head and needle position response, make sure that the
Serato DJ Library + Display preference Maximum Screen Updates Per Second
is set to 30 or higher.
9. Beat Jump: Press these buttons to jump back or forward in the software at the
set Beat Jump Length.
10. Beat Jump Length: Turn to increase or decrease the beat jump length. Push the
encoder to reset the Beat Jump length to 8 beats.

6
11. Slip / Vinyl: Press this button to enable or disable Slip mode. In Slip mode, you
can jump to Hot Cue Points, trigger Loop Rolls, or use the platters while the
track’s timeline continues. In other words, when you stop the action, the track
will resume normal playback from where it would have been if you had never
done anything (i.e., as if the track had been playing forward the whole time).
Press and hold Shift and press this button to activate or deactivate “vinyl
mode” for the jog wheel. When activated, you can use the jog wheel to
“scratch” the track as you would with a vinyl record. When deactivated (or if
you are touching only the side of the jog wheel), move the jog wheel to
temporarily adjust the track’s speed.
12. Censor / Reverse: Press and hold this button to activate Censor,
which temporarily reverses the playback of the track. Release the
11 12
button to resume normal playback from where it would have been
if you had never engaged the Censor function (i.e., as if the track
had been playing forward the whole time).
Silent Cue - The primary function of this button can be changed to
Silent Cue in the System menu.
13
Silent Cue temporarily mutes the deck audio until a Hot Cue or
Pitch Play pad is pressed. This allows you to play the song from the
desired position and unmute the deck with a single button press.
Press and hold Shift and press this button to activate Reverse, which 15
will reverse the playback of the track. Press the button again to
resume normal playback from wherever the audio playhead stops.
13. Shift: Press and hold this button to access secondary functions 14
when used with other controls.
14. Play/Pause: Press this button to start or pause the platter. The LED will be off
when no track is loaded, flashing green when a track is paused, and solid green
when a track is playing.
Press and hold Shift and press this button to perform stutter play if the track is in
the play state.
15. Cue / Previous: When the Deck is paused, you can set a Temporary Cue Point
by moving the platter to place the playhead at the desired location and then
pressing the Cue button.
During playback, you can press the Cue Button to return the track to this
Temporary Cue Point. (If you did not set a Temporary Cue Point, then it will
return to the beginning of the track.)
If the Deck is paused, you can press and hold the Cue button to play the track
from the Temporary Cue Point. Releasing the Cue button will return the track to
the Temporary Cue Point and pause it. To continue playback without returning
to the Temporary Cue Point, press and hold the Cue button, then press and
hold the Play button, and then release both buttons.
Press and hold Shift and press this button to return the track to its beginning.
Pressing this button combination again while at the beginning of the track will
load the previous track in the playlist to the deck.
16. Sync / Sync Off: Press this button to automatically match the corresponding
Deck’s tempo with the opposite Deck’s tempo.
Press and hold Shift and press this button to deactivate Sync.

7
17. Stem-Split: Pressing this button performs the Stem-Split function
within Serato DJ. The track that is loaded to the deck is instant
doubled to the layers of the respective side. Decks 1/2 are always 17
set to the acapella stem and decks 3/4 are always set to
instrumental stem regardless of what deck is in focus when the
Stem-Split button is pressed. This allows you to adjust level, EQ,
and apply effects to the instrumental or acapella independently.
By default, deck functions are locked together, press one of the
deck buttons to manipulate the stem elements independently
from each other. Press the Stem-Split button again to sync the
stem elements.
Tip: Ensure the level of your desired channels are the same before triggering
Stem-Split.

Performance Pads
1. Hot Cue / Pitch Play: Single press
this button to enter the first pad Combination Pad Mode:
mode, Hot Cue mode. Press the Pressing and holding one of the pad mode
button two consecutive times in buttons and then pressing another one will
quick succession to enter the enter combination pad mode. The first
secondary pad mode, Pitch Play button pressed from the top row of pads
mode. (1-4) will be the first pad mode and the
Custom User Mode: Press and hold second pad mode will be accessed from
Shift and press this button to access the lower pads (5-8). While in combination
the custom user pad mode where all pad mode the parameter buttons control
8 pads and the parameter buttons the first pad mode.
can be assigned to various software
features.
Note: The Serato Pitch N Time 1 2 3 4 5
plugin is required to use Pitch Play
mode.
2. Roll / Saved Loops: Single press
6 11 10
this button to enter the first pad
mode, Roll mode. Press the button 7 8
two consecutive times in quick 9
succession to enter the secondary 12 13
pad mode, Saved Loop mode.
3. Sampler / Scratch Bank: Single press this button to enter the first pad mode,
Sampler mode. Press the button two consecutive times in quick succession to
enter the secondary pad mode, Scratch Bank mode.
4. Stems: Single press this button to enter the first pad mode, Stem mode. Press
the button two consecutive times in quick succession to enter the secondary
pad mode, Slicer mode.
5. Parameter </>: Use these buttons to access various functions in each pad
mode.
6. Pad Display: Displays the current pad mode and/or specific pad info such as
sample name and hot cue names.

8
7. Performance Pads: These pads have
different functions on each deck depending
on the current pad mode.
Note: See the Operation > Pad Modes
section to learn how to use the pads in
7
each mode.
8. Acapella: Press to filter out the
instrumental and only play the vocals for
the current track. 8
Press and hold Shift and press this button
to apply an echo out effect to the removed
stem elements.
9
9. Instrumental: Press this button to filter out
the vocals of the current track to create an
instrumental for the current track.
Press and hold Shift and press this button
10
to apply an echo out effect to the removed
stem elements.
10. Key Adjust: Adjusts the key of the active
deck. Use < > to move up or down the key
scale.
11
Press and hold Shift and press < to turn on
Key Sync.
Press and hold Shift and press > to reset
the key.
Note: The Serato Pitch N Time plugin is
required to use Key Adjust.
11. Loop On/Off / Reloop: Press this button to
create an auto-loop with the length that is
12 13
set in the software.
Press and hold Shift and press this button to skip to the last-played loop and
activate it immediately.
12. x1/2 / Loop In: Press this button to halve the length of the current loop.
Press and hold Shift press this button to create a Loop In point at the current
location.
13. x2 / Loop Out: Press this button to double the length of the current loop.
Press and hold Shift and press this button to create a Loop Out point at the
current location.

9
Jog Wheel Display
The jog wheel displays are populated with a
waveform, graphics, and text, and controlled 2
by Serato DJ via MIDI messages.
1. Track Progress Ring: Displays the total 4
track progress in the outer ring. 6 5
2. Beat Jump Length: Displays the current
size of the Beat Jump Length.
7
3. Needle Position: This shows the rotating 3
playhead position. This can be turned off
from the System menu. 1
8 9 10
4. Pitch: Displays the current pitch
percentage value.
11
5. BPM: Displays the Beats Per Minute for
the current track.
6. Pitch Range: Displays the current pitch range value.
7. Waveform Overview: Displays the full track waveform with playhead position
(white) and hot cue indicators matching their assigned hot cue colors.
8. Song Key: Displays the song’s key value. This can change if the key is synced or
transposed up or down.
9. Time: Displays the time for the current song. This value may be shown as
elapsed or remaining, depending on the preference in the System menu.
10. Loop Size: Displays the current loop length.
11. Deck: This shows the active deck, 1/3 or 2/4.

10
FX Section

1. FX Display: Shows the current effect


and its parameters. 2 1 2
2. Main FX: Press one of these buttons 6 7
to arm a post-fader effect. Press and 5 4
hold a button and scroll with the 8 8
encoder through the list of effects.
Press the encoder to load the 3 9 3
selected effect.
• FX Save: Press and hold this button for 4 seconds to save the current
beats/parameter values to the FX slot.
• Parameter Reset: Press and hold Shift and press this button to recall the
user defined or factory default (if the effect has not been saved)
beats/parameter values for the loaded effect.
3. Effects Toggle: Move this toggle switch away from you to activate the effects—the
toggle will latch to that position. Push down on the paddle to turn the effects on
momentarily. Pull the toggle back to the center position to deactivate the effects.
• Menu Navigation: While the Menu is open, move the joystick to navigate
through menu options.
• Beat Value Reset: Push the joystick button to recall the user-defined or factory
default beat value (when the effect has not been saved) for the loaded effect.
4. Tap: Press this button 3 consecutive times at the desired tempo to manually set
the BPM rate for beat-tempo effects, per channel. Press and hold this button for
3 seconds to return the BPM back to BPM of the software deck.
5. Hardware/Software FX Select: Press to toggle between the internal Hardware
FX or software FX. Blue LED = Internal FX (default). Orange LED = Software
FX.
Press and hold Shift and press this button to access the System menu.
6. Parameter Encoder: Turn this to control the hardware FX parameters.
Push the encoder to cycle through available parameters for the assigned effect.
• Menu Navigation: While the Menu is open, move the joystick to navigate
through menu options.
• FX Select: Hold one of the 6 FX buttons and turn the encoder to scroll
through the available effects. Push the encoder to load the selected effect.
Press and hold Shift and turn the encoder for Manual BPM Adjust. This will
change the tempo of the selected BPM in tenth increments.
7. Parameter Joystick: Push this joystick up and down to adjust effect parameters
shown on the FX Display. Push this joystick left or right to select the left or right
BPM. This is only necessary when making manual FX tempo adjustments.
• Menu Navigation: While the Menu is open, move the joystick to navigate
through menu options.
• Beat Value Reset: Push the joystick button to recall the user-defined or factory
default beat value (when the effect has not been saved) for the loaded effect.

11
8. FX Assign Buttons: Press these buttons to assign which channel
will receive effects from the associated toggle: Decks 1 or 3 (Left
side) or Decks 2 or 4 (Right side).
8
Note: FX assignments can only be changed when the effect is
inactive.
9. FX Depth: Turn this knob to adjust the “wet-dry” mix of the effects
on the corresponding deck. For some effects, this will also change
the value of parameters that are also controlled with the Depth 9
knob.

Mixer Controls
1. Deck Source: Set this knob to the
desired MIDI and audio source for the 2 1 1 2
deck, USB A or B. This allows DJ 17 9
“handoffs” from one computer to
another.
3 13
2. USB/Line Source Selection: Adjust 19 4
this to set the channel source to 20
computer audio or line audio.
5
22 21 14
When set to USB, MIDI is sent to the 6
same computer connected to the 15
USB port on the rear panel for 8 7
control for that channel and
associated deck.
When set to Line, the audio input
signals are routed to channels 3 & 4
to be digitally mixed. Deck control
will no longer be in effect. Audio will 10
be mixed internally to the cue and
main output signals.
11
Note: If you select Line, set the
Phono/Line selector switches on the
rear panel properly.
Note: A deck’s controls will send
MIDI information only when its deck
source selector is set to USB A or B. 12
3. Deck Audio Level: Turn this knob to
set the pre-fader, pre-EQ audio level
of the corresponding channel.
4. Deck EQ High: Turn this knob to adjust the high (treble) frequencies.
5. Deck EQ Mid: Turn this knob to adjust the mid-range frequencies.
6. Deck EQ Low: Turn this knob to adjust the low (bass) frequencies.
Note: All EQ controls are full-kill.

12
7. Channel FX Knob: Turn this knob to adjust the filter
applied to the deck. Turn the knob counterclockwise to 8 7
apply a low-pass filter. Turn the knob clockwise to apply
a high-pass filter. Set it to the center (“12:00”) position to
deactivate the filters.
8. Channel FX Select: Press these buttons to select the
desired software Channel FX: Filter, Filter Roll, Noise, or
10
Flanger.
• Filter: Pre-fader. Can be a software or hardware
11
effect. When used as a hardware effect, it is only
available for line/phono sources.
• Filter Roll: Pre-fader. Software effect.
• Flanger: Pre-fader. Software effect. 12
• Noise: Pre-fader. Software effect.
Notes:
Upon power-up, the FX BPM will default to 100 BPM.
When connected to Serato DJ, the software will send the BPM (from the FX
Unit) for only the assigned channel as dictated by the hardware FX Assign
buttons (per side).
Use the Tap button to manually tap in the tempo in order to obtain the BPM for
line input signals.
9. Quantize: Press to activate quantize mode in the software.
10. Channel Cue: Press this button to send the pre-fader signal to the 9
cue channel for monitoring. When engaged, the button will be lit. To
cue multiple channels, press the Cue buttons at the same time for 13
each channel.
11. Channel/Deck Fader: Move this fader to adjust the volume level of
the corresponding deck.
12. Crossfader: Move this crossfader to mix between the decks. The 14
crossfader is user-removable and supports the Innofader as a 15
drop-in replacement. The crossfader tension can be adjusted by
removing the fader plate and adjusting the set screw on the
crossfader carrier.
13. Main Level: Turn this knob to adjust the output volume of the program mix. The
meters next to this knob indicate the audio signal level of the program mix.
14. Booth/Zone Level: Turn this knob to adjust the output volume of the Booth/Zone
Outs.
15. Sample Volume: Turn to adjust the gain of the software sample player.
16. Sampler Assign to Channel 4: Press to route the sampler to channel 4. This will
allow the sampler to have all gain, EQ, and FX controls for that channel.
17. Mic 1 On/Off / Talkover: Press this button to turn Mic 1 on and off.
Press and hold Shift and press this button to use the “talkover” 17
feature, which automatically reduces the volume level of the main
mix when you speak into the microphone. Talkover settings can be
adjusted in the System menu.
18. Mic 1 Level: Turn to adjust the level of Mic input 1.

13
19. Mic 1 High: Turn this knob to boost or cut the high
frequencies of the Mic 1 input. 19
20. Mic 1 Low: Turn this knob to boost or cut the low frequencies
of the Mic 1 input. 20
21. Mic 1 Echo: Turn this knob to adjust the Echo level of Mic
input 1. 22 21
22. Mic 1 Echo On/Off: Use this switch to turn Echo on or off for
Mic input 1.

Front Panel

1. Mic 2 Off/On: When set to Off, the Mic 2 Input is disabled. When set to On, the
Mic 2 Input on the rear panel is active, and its audio signal is routed directly to the
program mix.
2. Mic 2 Level: Turn this knob to adjust the gain of the Mic 2 Input.
3. Mic 2 High: Turn this knob to boost or cut the high frequencies of the Mic 2
Input.
4. Mic 2 Low: Turn this knob to boost or cut the low frequencies of the Mic 2
Input.
5. Crossfader Assign: These switches route the audio playing on the
corresponding channel to either side of the crossfader (L or R), or bypasses the
crossfader and sends the audio directly to the program mix (center position =
Thru).
6. Crossfader Contour: Adjusts the slope of the crossfader curve. Turn the knob to
the left for a slow fade (mixing) or to the right for a fast cut (scratching). The
center position is a typical setting for club performances.
7. Cue Mix: Turn to mix between the cue channel and program mix in the
headphone outputs. When all the way to the left, only the cue channel will be
heard. When all the way to the right, only the program mix will be heard.
8. Split Cue: When this switch is in the On position, the headphone audio will be
“split” such that the cue channel is summed to mono and sent to the left
headphone channel while the program mix is summed to mono and sent to the
right channel. When the switch is in the Off position, the cue channel and
program mix will be “blended” together. In both cases, use the Cue Mix knob to
control the blend of the two signals.
9. Cue Level: Turn this knob to adjust the volume level of the cue channel.
10. Headphone Outputs (1/4”, 1/8” / 6.35 mm, 3.5 mm, TRS): Connect your
headphones to these outputs for cueing and mix monitoring.

14
Rear Panel

1. Mic Inputs 1–2 (XLR / 1/4” / 6.35 mm, TRS): Connect dynamic microphones to
these mono inputs. Their mono audio signals are split and routed directly to the
stereo program mix and cue channel. If you prefer a stereo line input, the Deck
Phono/Line In may be used.
2. Deck Phono/Line In (RCA): Connect these inputs to an external audio source or
to a turntable, CD player, or other line-level device. Remember to set the
corresponding Phono/Line selector to the appropriate position and to set the
USB/Line Source Selection switch for that deck to Line to play its audio signal
on that deck.
3. Line/Phono Selectors: Set this switch to the appropriate position, depending on
the device connected to the Phono/Line Ins of the corresponding deck. If you
are using phono-level turntables, set this switch to Phono to provide the
additional amplification needed for phono-level signals. If you are using a line-
level device, such as a line-level turntable, CD player or sampler, set this switch to
Line.
4. Phono Ground: If you are using phono-level turntables with a grounding wire,
connect the grounding wire to this terminal. If you experience a low “hum” or
“buzz”, this could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection, so
nothing needs to be connected to the grounding terminal.
5. Main Out (RCA): Connect these outputs to another mixer, recording device, etc.
The program mix will be sent to these outputs.
6. Main Out (XLR): Connect these outputs to loudspeakers or an amplifier system.
Use the Main knob on the top panel to control the volume level.
7. Booth/Zone (1/4” / 6.35 mm): Connect these outputs to booth monitors or a
booth amplifier system. Use the Booth/Zone knob on the top panel to control
the volume level.
8. Stereo/Mono: Set this switch to have the Main Outs output a stereo or mono
audio signal.
9. USB Ports (USB Type-B): Use USB cables to connect these USB ports to
available USB ports on your computer. These connections send and receive
audio and MIDI control information to and from the computer.
10. Power Input: While FOUR is powered off, connect the included power cable to
this input and then to a power outlet.
11. Power Button: Use this button to power FOUR on or off. Power on FOUR only
after you have connected all your input devices and before you power on your
amplifiers and loudspeakers. Power off your amplifiers and loudspeakers before
powering off FOUR.

15
OPERATION

Pad Display
FOUR has monochrome OLED displays above each performance pad area which
offer two lines of text. The top line refers to the top row of pads and the second line
refers to the bottom row of pads. If the text string is longer than the length of the
screen, the line of text will scroll momentarily to show the full text and then return to
the first character. Scrolling will only occur the first time the text is shown on-screen
after changing modes.
• In Hot Cue pad mode, the displays will show the Hot Cue name. If the Hot Cue is
not named, then the song position (time) is shown.
• In Roll pad mode, the displays will show the Loop Roll value. When a Roll pad is
active, the display will show that line inverted with a solid White rectangular box.
• In Sampler pad mode, the displays will show the sample name. If a Sample pad is
empty, the display line for the corresponding pad will remain blank. When a
sample is playing, the display will show that line inverted with a solid white
rectangular box.
• In Stems pad mode, the first line will show the Stem element, and the second line
will show the Stem FX. Use pads 1-4 to toggle stems on/off (1-Vocal, 2-Melody, 3-
Bass, 4-Drums) and pads 5-8 to toggle stems FX on/off (5-Vocal Echo, 6-Drums
Echo, 7-Instrumental Braker, 8-Drums Braker).
• In Pitch Play pad mode, the displays will show the key change value (in
semitone) for each pad. When selected, the display will show that line inverted
with a solid white rectangular box.
• In Saved Loop pad mode, the displays will show the Saved Loop name. If the
Saved Loop is not named, then the Saved Loop start time will be shown. When a
Saved Loop is playing, the display will show that line inverted with a solid white
rectangular box.
• In Scratch Bank pad mode, the displays will show the name of the loaded
sample/song. If a Scratch Bank is empty, the display line for the corresponding
pad will remain blank.
• In Slicer pad mode, the displays will show the slice size. When a Slicer pad is
active, the display will show that line inverted with a solid white rectangular box.
• In Combination pad mode, the displays show the selected pad modes on the top
and bottom section of the display.

16
Pad Modes
This chapter describes the different pad
modes. Each deck has eight pads, which are 1 2 3 4
always in one of these modes, and each
deck’s pads can be in a different mode. Press
one of the Pad Mode buttons to enter the 6 7 8
5
corresponding pad mode on that deck. The
pads will remain dim when unselected, at full
brightness when a pad mode is selected, and
flashing between dim and full brightness
when a secondary pad mode is selected.

Hot Cue
In Hot Cue mode, each pad assigns a hot cue point in the software or returns the
track to that hot cue point. The performance pad LEDs will remain unlit until a hot
cue is placed or will light if the loaded track already has Hot Cue points assigned.
To enter Hot Cue mode, press Hot Cue.
To assign a hot cue point, press an unlit Pad at the desired point in your track. The
pad will light up when it is assigned (with the corresponding color, if available).
To jump to a hot cue point, press a lit Pad.
To delete an assigned hot cue point, press and hold Shift and then press the
corresponding pad.
To arm FLIP recording, press Parameter <. The Censor or Hot Cue action initiates
recording when FLIP mode is record armed. Press Parameter < again to disarm FLIP
recording.
To stop recording and turn FLIP on / loop FLIP, press Parameter >.
Note: FLIP Expansion is required for this function.

17
Roll
In Roll mode, each of the performance pads will perform a different time division
loop roll. Releasing the pad stops the loop roll and resumes normal playback where
the playhead would be if you had not triggered the loop roll (i.e., as if the track had
been playing forward the whole time). Enable the Show Beat Jump Controls option
in the software to have the bottom 4 pads to control beat jump functions.
Note: Disable Show Beat Jump Controls in the Serato Setup menu to access 8 loop
rolls at once. You can also view and edit the set loop sizes in the software.
To enter Roll mode, press Roll.
To trigger a loop roll, press and hold a Pad. The pad LED will be dim when a pad is
unpressed (roll inactive). The LED will be at full brightness when a pad is pressed
(roll active).
To shift the roll range down, press the Parameter < button.
To shift the roll range up, press the Parameter > button.
Press the Parameter < button while a roll is active to halve the length of the roll.
Press the Parameter > button while a roll is active to double the length of the roll.

Sampler
In Sampler mode, each pad triggers a sample, which you can assign in the software.
To enter Sampler mode, press Sampler. The pad LED will be unlit when no sample
is loaded to a pad. The LED will be bright Pink when a sample is loaded to a pad.
The LED will flash between off and bright Pink when a sample is playing.
To stop sample playback, press and hold Shift and press the corresponding pad.
To cycle the Sample bank selection left, press the Parameter < button.
To cycle the Sample bank selection right, press the Parameter > button.
To cycle through the sampler outputs, press and hold Shift and then press the
Parameter < or > button.

Stems
In Stems mode, the top 4 pads can be used
to mute stem elements and the bottom 4
pads can be used to activate stem FX. VOCAL MELODY BASS DRUMS

To enter Stems mode, press Stems.


For Stem Elements (pads 1-4), the pad FX
FX INST FX INST
FX
LED will be unlit when a Stem element is VOCAL DRUMS
ECHO BREAKER
ECHO ECHO
muted/removed. The LED will be bright
Blue when a Stem element is playing.
For Stem FX (pads 5-8), the pad LED will be unlit when Stem FX is off. The LED will
be bright Amber when Stem FX are on.
To activate an instant acapella, press the Parameter < button.
To activate an instant instrumental, press the Parameter > button.

18
Pitch Play

To enter Pitch Play mode, quickly double tap this button. In this mode, the
performance pads offer a range of different keys for the active hot cue (adjustable
by semitones). The Serato Pitch N Time plugin (included) must be installed to use
this mode. See Hot Cue to learn how to assign hot cue points.
To enter Pitch Play mode, quickly double tap Hot Cue pad mode button.
To select which hot cue point to use, press and hold Shift and press a dimly lit
Pad.
To select the range of transpositions the pads will use, press the Parameter </>
buttons.
To play the track from the hot cue point, press a lit Pad. Each pad corresponds to a
specific transposition (by semitones), depending on the current range of
transposition.
A pad with no semitone selected will be lit dim. A pad with a semitone selected will
be lit at full brightness. A pad with no transposition (the original pitch) will be lit
white.

Saved Loops

In Saved Loops mode, each pad triggers a loop previously saved in your software.
To enter Saved Loops mode, quickly double tap Roll pad mode button. The pad
LED will be off when no loop is saved to a pad. The LED will be bright Green when a
loop is saved to a pad. The LED will be bright Blue when a saved loop is active.
To play a loop, press a lit Pad. Each deck’s eight pads will correspond to Saved
Loops 1–8 in your software.
To activate the saved loop, press the pad to activate the loop or press and hold
Shift and press the corresponding pad to activate and jump to the loop position in
the track.
To halve the loop size, press the Parameter < button.
To double the loop size, press the Parameter > button.
To move the active loop region backward at the current loop size without
deactivating the loop, press and hold Shift and then press the Parameter < button.
To move the active loop region forward at the current loop size without
deactivating the loop, press and hold Shift and then press the Parameter > button.

19
Scratch Bank
In Scratch Bank mode, each pad loads samples and tracks from your Serato DJ Pro
library to a pad. You can assign the song and set the starting point in the software.
This is useful for preparing and performing with song samples for scratching.
To enter Scratch Bank mode, quickly double tap the Sampler pad mode button.
The pad LED will be off when no track is loaded. The LED will be bright White when
a Scratch Bank track is loaded to a pad. Colors can be set in the Scratch Bank panel
within the Serato DJ Pro software.
To load the selected track to a pad, press an unlit Pad. When that pad is pressed
again, the corresponding track will be loaded to the deck.
To load the track that was previously on the deck before loading a Scratch Bank
track, press and hold Shift and press the corresponding pad.
To cycle the Scratch Bank selection left, press the Parameter < button.
To cycle the Scratch Bank selection right, press the Parameter > button.

Slicer Mode
In Slicer mode, the eight pads represent eight sequential beats (slices) in the
beatgrid. The currently playing slice is represented by the currently lit pad; the light
will “move through the pads” as it progresses through the eight-slice phrase. When
you release the pad, the track will resume normal playback from where it would have
been if you had never pressed it (i.e., as if the track had been playing forward the
whole time).
To enter Slicer mode, quickly double tap the Stems pad mode button. The pad LED
will be bright Red for all sliced pads. The LED will be bright Blue for the playhead
position or current slice. The LED will be bright White while a pad is pressed.
To play a slice, press the corresponding pad.
To halve the slice domain size, press the Parameter < button.
To double the slice domain size, press the Parameter > button.

20
APPENDIX

Internal Hardware Effects


Effects Notes:
• Beat time divisions are unique per effect.
• Each effect will initially load at their default values (seen in the tables below).
• During a session, the parameter and beat values can be changed. The values for
the last used state are recalled when changing between effects.
• All saved effects (FX buttons 1-6) and their user-defined parameter/beat values
(not the last used settings) are loaded on startup. If an effect assigned to one of
the FX buttons 1-6 has not been saved, the factory effect and its default
parameter/beat values are loaded for that effect slot.

Name Description Control Beats Parameter Depth


1 Backspin Simulates a Paddle Length N/A < 50% - the
turntable backspin. (in beats): Backspin
When FX Depth 2, 4, 8 speed is
is centered, the slower than
Default: 8
backspin length the speed as
is as shown by shown by
the beat’s value. the beat's
Turn FX Depth value. Beat
left or right to values less
decrease or than the
increase the current beat
backspin length selection
respectively. are scaled
linearly from
50-0%.
50% - the
Backspin
speed is as
shown by the
beat's value.
>50% - the
Backspin
speed is
faster than
the speed as
shown by the
beat's value.
Beat values
greater than
the current
beat
selection are
scaled
linearly from
50-100%.

21
Name Description Control Beats Parameter Depth
2 Beatbreak Samples the 4 Paddle Pattern: HPF Cut Off: 0-100%
beats of each 1-10 40 Hz, The effect wet
bar of the 80 Hz, mix is applied
Default: 1
original signal 140 Hz, 244 on a linear
and replays Hz, 427 Hz, scale.
them (within 748 Hz, 1308
the same bar) Hz, 2287 Hz,
according to 4000 Hz
the selected
Default: 244
pattern. Turn
Hz
FX Depth to
adjust the
balance of the
original and
the effected
signal in the
mix.
3 Bit Crush Adds distortion Paddle Average: 8, Bit Depth: 0-100%
by reducing the 16, 32, 64 8, 16 The effect wet
resolution or Default: 16 Default: 8 mix is applied
bandwidth of on a linear scale.
the original
audio signal.
Turn FX Depth
to adjust the
balance of the
original and the
effected signal
in the mix.
4 Brake Simulates a vinyl Paddle Beats: N/A < 50% - the
turntable stop. 1/2, 1, 2, 4, 8, Brake speed is
When FX Depth 16, 32 slower than the
is centered, the speed as shown
Default: 2
brake length is by the beat's
as shown by the value. Beat
beat’s value. values less than
Turn FX Depth the current beat
left or right to selection are
decrease or scaled linearly
increase the from 50-0%.
brake length 50% - the Brake
respectively. speed is as
shown by the
beat's value.
>50% - the
Brake speed is
faster than the
speed as shown
by the beat's
value. Beat
values greater
than the current
beat selection
are scaled
linearly from 50-
100%.

22
Name Description Control Beats Parameter Depth
5 Cyclone Adds delays of the Paddle Beats: Delay Time: 0-100%
original signal at 1/64, 1/32, 5-400 ms The effect wet
the specified beat 1/16, 1/8, mix is applied
Default:
time or delay time. 1/4, 1/3, 1/2, on a linear
360 ms
Turn FX Depth to 3/4, 1, 3/2, scale. As the
adjust the balance 2, 3, 4 effect wet mix
of the original and Default: is increased,
the effected signal 3/4 the program
in the mix. Turn FX signal is
Depth to the max reduced. Turn
position to hold Depth to the
the current delay max position
sample infinitely. to hold the
current delay
sample.
6 Delay Adds repeated Paddle Beats: N/A 0-100%
instances of the 1/32, 1/16, The effect
original signal at 1/8, 1/4, wet mix is
the specified 1/3, 1/2, applied on a
beat time. Turn 3/4, 1, 2, 4 linear scale.
FX Depth to Default: 1 As it is
adjust the increased,
balance of the the program
original and signal is
effected signal in reduced.
the mix.
7 Duck Creates echoes Channel Beats: HPF Cut 0-100%
Echo of the original fader of 1/32, 1/16, Off: The effect
signal at the the 1/8, 1/4, 40 Hz, level is applied
specified beat assigned 1/3, 1/2, 80 Hz, on a linear
time when a deck is 3/4, 1, 2, 140 Hz, scale.
channel or lowered 4, 8, 16 244 Hz,
crossfader is or 427 Hz,
Default:
moved to the crossfader 748 Hz,
1/2
minimum if the 1308 Hz,
position. Turn crossfader 2287 Hz,
FX Depth to trigger is 4000 Hz
adjust the assigned. Default:
balance of the 244 Hz
original and the
Feedback:
effected signal in
0-100%
the mix.
Default:
80%
Crossfader
Trigger:
Yes, No
Default:
Yes

23
Name Description Control Beats Parameter Depth
8 Echo Adds echoes of Paddle Beats: HPF Cut Off: 0-100%
the original 1/32, 1/16, 40 Hz, The effect wet
signal at the 1/8, 1/4, 80 Hz, mix is applied
specified beat 1/3, 1/2, 140 Hz, 244 on a linear
time. 3/4, 1, 2, 4, Hz, 427 Hz, scale.
Turn FX Depth 8, 16 748 Hz, 1308
to adjust the Hz, 2287 Hz,
Default:
balance of the 4000 Hz
1/2
original and the Default:
effected signal 244 Hz
in the mix. Feedback:
0-100%
Default: 80%
9 Echo Out This creates an Paddle Beats: HPF Cut Off: <50% - The
Default: 6 echo tail of the 1/8, 1/4, 40 Hz, effect is mixed
original signal 1/3, 1/2, 80 Hz, with the
at the 3/4, 1, 3/2, 140 Hz, 244 program audio
specified beat 2, 3 Hz, 427 Hz, from the
size while 748 Hz, 1308 assigned deck.
Default:
muting the Hz, When Depth
1/2
original signal. 2287 Hz, knob is turned
Turn Depth to 4000 Hz to the left of
the max Default: the center, the
position to hold 140 Hz effect wet mix
the echo tail is reduced.
infinitely. 50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
>50% - The
effect is 100%
wet and no
program audio
from the deck
is heard
while the
effect is
engaged.
When Depth
knob is turned
to the right of
the center, the
tail length
(feedback) is
increased.

24
Name Description Control Beats Parameter Depth
10 Flanger Adds a slightly Paddle Beats: Feedback: 0-100%
delayed copy of 1/16, 1/8, 0-100% The effect wet
the original 1/4, 1/2, 1, Default: 34% mix is applied
signal to create 2, 4, 8, 16, on a linear
Polarity:
a comb-filter 32, 64 scale.
Positive
effect.
Default: 16 (POS),
Turn FX Depth Negative
to adjust the (NEG)
balance of the
Default: POS
original and
effected signal in
the mix.
11 Hold Adds echoes of Paddle Beats: Feedback: <50% - The
Echo the original 1/32, 1/16, 0-100% effect is mixed
signal at the 1/8, 1/4, Default: 80% with the
specified beat 1/3, 1/2, program audio
HPF Cut Off:
time. 3/4, 1, 2, 4, from the
40 Hz,
When FX Depth 8, 16 assigned deck.
80 Hz,
is centered, the When Depth
Default: 1 140 Hz, 244
echo will repeat knob is turned
Hz, 427 Hz,
or ‘hold’ to the left of
748 Hz, 1308
infinitely. Turn the center, the
Hz, 2287 Hz,
FX Depth to the effect wet mix
4000 Hz
right to increase is reduced.
Default: 244
the echo 50% - The
Hz
feedback. effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
>50% - The
effect is 100%
wet and no
program
audio from
the deck is
heard while
the effect is
engaged.
When Depth
knob is
turned to the
right of the
center, echo
feedback is
increased.

25
Name Description Control Beats Parameter Depth
12 Matrix Performs a Paddle Beats: Length: 0-100%
Default: rapid sweep 1/32, 1/16, 1-9 The effect
FX 5 through beat 1/8, 1/4, Default: 5 wet mix is
values lower 1/3, 1/2, applied on a
than the 3/4, 1, 3/2, linear scale.
specified beat 2, 3 As it is
size and then Default: increased, the
echoes out at 1/2 program signal
the specified is reduced.
beat time
division.
Turn FX Depth
to the max
position to hold
the current
echo infinitely.
13 Phaser This adds a Paddle Beats: Feedback: 0-100%
copy of the 1/16, 1/8, 0-100% The effect wet
original signal 1/4, 1/2, 1, Default: 47% mix is applied
with its phase 2, 4, 8, 16, on a linear scale.
shifted 32, 64
slightly to Default: 16
create a
subtle,
modulated
effect.
Turn FX
Depth to
adjust the
balance of
original and
effected
signal in the
mix.

26
Name Description Control Beats Parameter Depth
14 Pitch DN Samples the Paddle Beats: Length: <50% - The
original signal 1/16, 1/8, 1-9 effect is
and repeats at 1/4, 1/3, mixed with the
Default: 7
the specified beat 1/2, 3/4, 1, program audio
time while 2 from the
pitching the Default: assigned deck.
sample down 1/4 When the
by semitone Depth knob
steps. is turned to
Turn FX Depth the left of the
to the right center, the
shortens the effect wet
sample length. mix is
reduced.
50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
>50% - The
effect is
100% wet
and no
program audio
from the deck
is heard while
the effect is
engaged.
When Depth
knob is
turned to the
right of the
center, the
length of the
repeated
sample is
reduced.
15 Pumper Momentarily Paddle Beats: Offset: 0-100%
attenuates the 1/32, 1/16, -1/2, -1/4, The effect
original signal at 1/8, 1/4, -1/8, -1/16, wet mix is
the specified 1/3, 1/2, 0 applied on a
beat time. Turn 3/4, 1, 2, 4, Default: linear scale.
FX Depth to 8, 16, 32
-1/2
adjust the balance Default: 1
of the original and Depth:
effected signal in -40 dB to
the mix. -2 dB
Default:
-20 dB

27
Name Description Control Beats Parameter Depth
16 Recycler This adds Paddle Beats: Resonance: 0-100%
Default: FX 2 echoes of the 1/64, 1/32, Low, Med, The effect
original signal 1/16, 1/8, 1/4, High wet mix is
at the specified 1/3, 1/2, 3/4, Default: applied on
beat time or 1, 3/2, 2, 3, 4 Med a linear
delay time. Default: 3/4 scale. As it
Turn FX Depth is
to adjust the increased,
balance of the feedback
original and is also
effected increased.
signal in the
mix and
increases
feedback.
17 Reverb Adds reflections Paddle Room Size: HPF Cut 0-100%
of the original Small (SML), Off: The effect
signal in Large (LRG) 40 Hz, wet mix is
simulated Default: 80 Hz, applied on
environment. LRG 140 Hz, a linear
Turn FX Depth 244 Hz, scale.
to adjust the 427 Hz,
balance of the 748 Hz,
original and the 1308 Hz,
effected signal 2287 Hz,
in the mix. 4000 Hz
Default:
244 Hz
Decay:
0-100%
Default:
75%

28
Name Description Control Beats Parameter Depth
18 Rider This samples the Paddle Beats: Scale: <50% - The
original signal and 1/16, 1/8, Major, effect is mixed
repeats at the 1/4, 1/3, 1/2, Minor, with the
specified beat time 3/4, 1, 2 Oct1, Oct2, program audio
while pitching the Default: 1/2 Penta from the
sample down and Default: assigned deck.
up repeatedly based Major When the
on the selected scale. Depth knob is
Turn FX Depth to turned to the
the right to shorten left of the
the sample length. center, the
effect wet mix is
reduced.
50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
>50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
When Depth
knob is turned
to the right of
the center, the
length of the
repeated
sample is
reduced.

29
Name Description Control Beats Parameter Depth
19 Riser This samples Paddle Beats: Length: <50% - The
Default: the original 1/4, 1/2, 3/4, 1-9 effect is mixed
FX 4 signal at the 1, 2 with the
Default: 7
specified beat program audio
Default: 3/4
time and from the
repeats it while assigned deck.
increasing the When Depth
repeat speed, knob is turned
and pitching to the left of
the sample up, the center, the
and then fades effect wet mix
out. is reduced.
Turn FX Depth 50% - The
to adjust the effect is 100%
rise speed. wet and no
program audio
from the deck
is heard while
the effect is
engaged.
>50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged.
When Depth
knob is turned
to the right of
the center, the
speed of rise
can be
adjusted.

30
Name Description Control Beats Parameter Depth
20 Roll This samples Paddle Beats: HPF Cut Off: 0% - The effect is
the original 1/64, 40 Hz, 80 Hz, not heard, and the
signal and 1/32, 140 Hz, 244 Hz, effect buffer is
repeats it at the 1/16, 1/8, 427 Hz, 748 Hz, reset if the effect
specified beat 1/4, 1/3, 1308 Hz, 2287 was previously
time. 1/2, 3/4, Hz, 4000 Hz engaged.
Turn FX Depth 1, 3/2, 2, Default: 40 Hz <50% - The effect
to the right to 3, 4 is mixed with the
shorten the roll Default: program audio
length 1/2 from the assigned
deck. When Depth
knob is turned to
the left of the
center, the effect
wet mix is
decreased linearly.
50% - The effect is
100% wet and no
program audio
from the deck is
heard while the
effect is engaged.
>50% - The effect
is 100% wet and
no program audio
from the deck is
heard while the
effect is engaged.
When Depth knob
is turned to the
right of the center,
the length of the
repeated sample is
reduced.

31
Name Description Control Beats Parameter Depth
21 Scale DN This Paddle Beats: Scale: <50% - The
Default: FX 3 samples the 1/32, 1/16, Major, effect is mixed
original 1/8, 1/4, Minor, with the
signal and 1/3, 1/2, Whole, program audio
repeats at 3/4, 1, 2, 3 Penta from the
the Default: Default: assigned deck.
specified 3/2, 1/2 Major When Depth
beat time knob is turned
while to the left of
pitching the the center, the
sample effect wet mix
down based is reduced.
on the 50% - The
selected effect is 100%
scale. wet and no
Turn FX program audio
Depth to from the deck
the right to is heard while
shorten the the effect is
sample engaged.
length. >50% - The
effect is 100%
wet and no
program audio
from the deck
is heard while
the effect is
engaged. When
Depth knob is
turned to the
right of the
center, the
length of the
repeated
sample is
reduced.
22 STTR Out This Paddle Pattern: Bars: 0-100%
samples the 1, 2, 3, 4, 5, 1, 2, 3 The effect wet
original 6, 7, 8, 9, Default: 2 mix is applied
signal and 10T, 11T, on a linear
repeats the 12T, 13T scale. As it is
sample at Default: 5 increased, the
the length of the
specified repeated
rhythmic sample is
pattern and reduced.
then fades
out.
Turn FX
Depth to
the right to
shorten
the sample
length.

32
System Menu
The FOUR System menu allows you to customize crossfader, microphone, display,
and other device settings. To access the System menu settings, press and hold Shift
and press the HW / SW FX button.
The joystick and the Parameter/FX Select encoder can be used to navigate the
menu.
Push the Parameter/FX Select encoder to confirms value changes.
To exit the System menu settings, use the joystick to navigate back to the root.
Alternatively, press HW / SW FX or one of the 6 FX slot buttons to exit the System
menu.

Menu:
• CENSOR: This setting allows you to change the function of the Censor button.
o MODE: NORMAL or SILENT CUE (Default = NORMAL)

• CROSSFADER: This setting allows you to change the crossfader cut in.
o CUT IN LEFT: 0-10 (Default = 3)
o CUT IN RIGHT: 0-10 (Default = 3)
o RESTORE DEFAULTS: CANCEL or RESTORE (Default = CANCEL)

• MICROPHONE: This menu option allows you to change microphone echo,


talkover, and microphone signal routing.
o ECHO FDBK: 0-100% (Default = 80%)
o TALKOVER LV: LOW (-10 dB), MED (-20 dB), HIGH (-40 dB) (Default = -20
dB)
o TALKOVER HLD: 0.5 - 2.0s (Default = 1.0s)
o TO BOOTH: ON, OFF (Default = OFF)
o TO HEADPHONE: ON, OFF (Default = OFF)
o TO COMPUTER: ON, OFF (Default = ON)

• WHEEL DISPLAY: This menu option allows you to change wheel display options.
o NEEDLE MARKER: ON, OFF (Default = ON)
o TIME: Remaining, Elapsed (Default = Remaining)

• FIRMWARE: This menu option shows you the current firmware versions.
o CONTROLLER: x.x.x.xxx
o DISPLAYS: x.x.x.xxx
o DSP: x.x.x.xxx
o MAG FADER: x.x.x.xxx

• FX RESET: This setting allows you to reset all FX settings back to their default
values.
o FX RESET: RESTORE, CANCEL (Default = CANCEL)

33
• FACTORY RESET: This setting allows you to reset all device settings back to
their default values.
o FACTORY RESET: RESTORE, CANCEL (Default = CANCEL)

34
Technical Specifications

Digital Audio
Converters Cirrus Logic, 24-bit PCM, 48 kHz

Digital Signal Processing 32-bit, Floating Point, Double precision

Dynamic Range ADC 113 dB


(A-weighted, unity gain)
DAC 113 dB

CD Input to Analog Output 110 dB

CD Input to USB Output 113 dB

USB Input to Analog Output 113 dB

Inputs
Microphone 1/2 Analog Gain 25 dB
(Combo XLR / 1/4" [6.35
mm] TRS) Maximum Input 110 mV

Gain Trim Off to +26 dB (unity at center)

Tone Control 2-band

Line/Phono Inputs 3/4 Line Line


(RCA stereo pairs,
switchable) Maximum Input 4 Vrms

Gain Trim Off to +12 dB

Tone Control 3-band, full-cut to +10 dB

THD+N (20 kHz BW @ 1 kHz) 0.004%

Phono RIAA

RIAA Curve +/-0.25 dB

Gain (@ 1 kHz) 31.5 dB

Maximum Input (@ 1 kHz) 106 mV

Dynamic Range 102 dB


(A-weighted)

Outputs
Main Outputs Gain Trim Off to 0 dB
(XLR)
Maximum Output 8 Vrms

THD+N (20 kHz BW @ 1 kHz) 0.004%

Frequency Response 20 Hz – 20 kHz (Flat)

Booth Outputs Gain Trim Off to 0 dB


(XLR)
Maximum Output 8 Vrms

THD+N (20 kHz BW @ 1 kHz) 0.004%

Frequency Response 20 Hz – 20 kHz (Flat)

35
Outputs (continued)
Main Outputs Gain Trim Off to 0 dB
(XLR)
Maximum Output 8 Vrms
THD+N (20 kHz BW @ 1 kHz) 0.004%

Frequency Response 20 Hz – 20 kHz (Flat)

Main Outputs Maximum Output Voltage 4 Vrms


(RCA stereo pair)
THD+N (20 kHz BW @ 1 kHz) 0.004%

Frequency Response 20 Hz – 20 kHz (Flat)

Booth Outputs Gain Trim Off to 0 dB


(1/4”)
Maximum Output 8 Vrms
THD+N (20 kHz BW @ 1 kHz) 0.004%

Frequency Response 20 Hz – 20 kHz (Flat)

Headphone Outputs Maximum Output Voltage 4 Vrms (no load)


(1/4" / 6.35 mm and 1/8" / 3.5
mm TRS) Output Power 50 mW (50 ohms)

Dynamic Range 108 dB


(A-weighted)

General
Pads (16) on/off multi-color back-lit pads (8 per deck, 9 modes
each)

Wheel Displays (2) 320 x 240 Color LCD’s

Pad & FX Displays (9) 128 x 32 Monochrome OLED’s

Faders (1) MAG FOUR tension-adjustable crossfader with contour

(4) Standard channel faders

Connectors (2) XLR outputs (Main)

(2) 1/4" outputs (Booth)

(1) RCA stereo output pair (Main)

(2) XLR / 1/4” (6.35 mm) TRS inputs (Mic 1–2)

(2) RCA stereo input pairs (Deck 3–4)

(1) 1/4” (6.35 mm) TRS output (Headphones)

(1) 1/8” (3.5 mm) TRS output (Headphones)

(2) USB Type-B ports

(1) IEC power cable input

Power Connection: IEC

Voltage: 100–240 V, 50/60 Hz

Consumption: 20 W

36
Dimensions 30.8” x 15.9” x 4.2”
(width x depth x height)
782 mm x 404 mm x 107 mm

Weight 18.25 lbs.


(including platters)
8.27 kg

Specifications are subject to change without notice.

Trademarks & Licenses

Rane is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries.

Serato, Serato DJ Pro, and the Serato logo are registered trademarks of Serato Audio Research.

Windows is a registered trademark of Microsoft Corporation in the United States and other
countries.

macOS is a trademark of Apple Inc., registered in the U.S. and other countries.

DeoxIT® is a registered trademark of CAIG Laboratories, Inc..

All other product names, company names, trademarks, or trade names are those of their
respective owners.

37
Manual Version 1.0

You might also like