Scribd
Upload
47 views4 pages

MPI Assignments (3160712)

Uploaded by

harshbopaliya13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
47 views4 pages

MPI Assignments (3160712)

Uploaded by

harshbopaliya13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Assignment-1

Branch: 6TH CE
Subject: MICROPROCESSOR & INTERFACING
Subject code: 3160712

Q.1 Define the terms:


(1) Microprocessor (2) Bus (3) Mnemonics (4) Compiler (5) Assembler
(6) Interpreter
Q.2 Explain the Architecture of 8085.
Q.3 Explain the Pin Configuration of 8085.
Q.4 Explain Programming Model of 8085.
Q.5 Explain Bus Organisation of 8085.
Q.6 What are the control signals? How do we generate them? Give their importance.
Q.7 Explain how to demultiplex the Multiplexed Address/Data Bus AD0-AD7.
Q.8 Explain the Interrupts of 8085.
Assignment-2
Branch: 6TH CE
Subject: MICROPROCESSOR & INTERFACING
Subject code: 3160712

Q.1 Answer the following Questions:


1) How many address lines are required on 2K byte Memory?
2) If the memory chip is 1024x4 bits, how many chips are required to make up 2K byte
memory.
3) The memory address of last location of an 8K byte memory chip is FFFFh. Find the
address of the starting location of the chip.
4) The memory map of a 4K byte memory chip begins at location 2000h. Specify the
address of the last location of the chip.

Q.2 Explain memory interface diagram for interfacing of 10kb RAM and 4kb PROM to 8085.
Q.3 Compare I/O Mapped I/O and Memory Mapped I/O.
Q.4 Define the Terms:
(1) Machine Cycle (2) Instruction Cycle (3) T-State

Q.5 Draw the Timing Diagram for the Instruction code 0100 1111 (4FH-MOV C, A) stored at
Location 2005h.

Q.6 Draw Timing Diagram for instruction STA 2065H.


Q.7 Draw Timing Diagram for instruction MOV A, M.
Assignment-3
Branch: 6TH CE
Subject: MICROPROCESSOR & INTERFACING
Subject code: 3160712

Q.1 Explain the Addressing Modes of 8085.


Q.2 Explain the types of Instructions.
Q.3 Explain the Instructions given below:
(1) PUSH & POP (6) XRA (11) RIM & SIM
(2) LDA & STA (7) LXI (12) INX
(3) LHLD (8) DAA & DAD (13) RRC
(4) XTHL (9) CMP (14) RAL
(5) MOV M, R (10) CMA (15) ACI
Q.4 Explain the time delay techniques in details.
Q.5 Write a program to generate the time delay of 0.3sec.Operating frequency is 2MHz
(FCLK=2MHz).
Assignment-4
Branch: 6TH CE
Subject: MICROPROCESSOR & INTERFACING
Subject code: 3160712

Q.1 Explain Architecture of 8086.


Q.2 Explain Programmable Interrupt Controller 8259 in detail.
Q.3 Explain Programmable Peripheral Interface 8255.
Q.4 Explain Architecture of 8086.
Q.5 Enlist the features of 80286 & 80386.
Q.6 List out the advantages of Segmentation.

You might also like