Schneider P3U30 V30.205 Feeder PTT User Manual ENU

OMICRON PTL Schneider P3U30 Feeder PTT User Manual
OMICRON PTL
Schneider P3U30 V30.205 Feeder PTT
User Manual
V1.000
© OMICRON electronics GmbH 1/6

Content
1. General ...................................................................................................................................................3
1.1 Supported Relays .................................................................................................................................3
2. Software and Hardware Requirements ...............................................................................................3
3. Hardware ................................................................................................................................................4
4. Functional Range...................................................................................................................................5
5. XRIO Converter ......................................................................................................................................5
6. Specific Protection Tests ......................................................................................................................6
6.1 Instantaneous tripping at switch onto fault ...........................................................................................6

1. General
This user manual describes details of testing Schneider P3U30 relays with the OMICRON
Protection Test Template. General information on the usage of OMICRON Protection Testing Library
items can be found in the OMICRON PTL user manual.
The template has been tested with the following relay:

Manufacturer: Schneider Electric
Model: P3U30
Firmware Version: 30.205
1.1 Supported Relays

The following relays can be tested with the Protection Test Template:
• P3U30
• P3U20
• P3U10
• P3F30
2. Software and Hardware Requirements

To use this template, you must have a valid test license for the OMICRON Test Universe 4.31 software or
higher versions and the following test modules:
• Control Center
• Quick CMC
• Overcurrent
• State Sequencer
Any CMC test set can be used with this PTT.

3. Hardware
There are multiple possibilities of wiring a Schneider P3U30 relay to a CMC test set. The advised
connections are shown in Figure 1. These connections are the default settings in the
Hardware Configuration of the PTT.
detection*
Dead line
VC
VA
VB
*: if needed for the SOTF test

IA
IB
IC
CB aux. 52a
CB aux. 52b
N
Trip
Pickup
IN
Figure 1: Default connection for Schneider P3U30

4. Functional Range
Supported functions:
• Phase overcurrent 50/51
• Ground fault overcurrent 50N/51N (calculated or measured IN)
• Directional phase overcurrent 67
• Direct. Ground fault overcurrent (calculated or measured IN)
• Switch on-to-fault 50HS
Not supported parameters or configurations:

• Direct. Ground fault overcurrent: Direction mode set to “ResCap”
• Overcurrent protection: Delay curve family set to “RI” or “Prg-”
• Voltage meas. Mode other than “3LN”
Not supported functions:

• Voltage-dependent overcurrent
• Transient intermittent ground fault
• Thermal overload
• Phase Undercurrent
• Voltage protection
• Neutral voltage protection
• Frequency protection
• Power protection
• Breaker failure
• Auto-recloser
• Inrush detection
• Programmable stages
Although the functions listed above are not supported by the Protection Test Template, the
Relay Parameter Section of the XRIO Converter includes most protection parameters of the relay
regarding the feeder application mode.
5. XRIO Converter
The Test Object already contains the Schneider P3U30 XRIO Converter, which includes setting
parameters of the modelled protection relay. The setting parameters are built as an image of the English
(US) setting names of the Schneider eSetup Easergy Pro V4.12 software.
General information about the converter structure can be found in the OMICRON PTL user manual.

6. Specific Protection Tests
6.1 Instantaneous tripping at switch onto fault
All SOTF test modules support both, the automatic dead line detection with an internal current criterion or
with help of a dead line detection input. If the relay is configured to detect the dead line by the binary
input, the CMC binary output 1 must be connected to that input.
The State Sequencer test module is used to test the instantaneous tripping at switch onto fault function.
Each SOTF parameter is tested with a different module as described in the following part. For each
module the reaction and trip time of the relay is measured and assessed.
• The first test module assesses the Pick-up setting of the SOTF function by simulating a state
where the pickup value is exceeded and one where it is not exceeded.
• The second test module addresses the 50HS active after CB closure parameter by considering
intermediate states with durations below and above the setting.
• The last test module evaluates the Dead line detection delay time by simulating CB Open states
with durations below and above the setting. There is an additional intermediate state (with normal
operation condition) to ensure that the SOTF active time is reset, before the next iteration starts.

Schneider P3U30 V30.205 Feeder PTT User Manual ENU

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Schneider P3U30 V30.205 Feeder PTT User Manual ENU

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Schneider P3U30 V30.205 Feeder PTT User Manual ENU

Uploaded by

Copyright:

Available Formats

OMICRON PTL Schneider P3U30 Feeder PTT User Manual

Schneider P3U30 V30.205 Feeder PTT

© OMICRON electronics GmbH 1/6

© OMICRON electronics GmbH 2/6

The template has been tested with the following relay:

1.1 Supported Relays

2. Software and Hardware Requirements

Any CMC test set can be used with this PTT.

© OMICRON electronics GmbH 3/6

*: if needed for the SOTF test

Figure 1: Default connection for Schneider P3U30

© OMICRON electronics GmbH 4/6

Not supported parameters or configurations:

Not supported functions:

© OMICRON electronics GmbH 5/6

6. Specific Protection Tests

6.1 Instantaneous tripping at switch onto fault

© OMICRON electronics GmbH 6/6

You might also like