TAWM SERIES

STANDARD AND SLIM

ELECTRONIC TORQUE-ANGLE WRENCH
WITH MEMORY

Original Instructions

1
TAWM SERIES

IMPORTANT SAFETY INSTRUCTIONS SPECIFICATIONS

WARNING. • When using negative offsets, verify HEAD TYPE STD CW CCW
RISK OF FLYING PARTICLES. maximum targets are not exceeded Square drive 48 teeth ±2% ±3% of reading, 20% to 100%
Over-torquing can cause breakage. (see tables on page 6). 9x12, 14x18 & 24x32 receivers for interchange- of full scale
Force against flex stops on flex • Verify calibration if dropped. able head Torque: ±4% ±6% of reading, 10% to 19%
head can cause head breakage. An • Make sure ratchet direction lever is (unflexed) of full scale
out of calibration angle wrench can fully engaged in correct position. DISPLAY ±8% ±10% of reading, 5% to 9%
cause part or tool breakage. Broken • Verify calibration of wrench if you • DISPLAY TYPE: of full scale
hand tools, sockets or accessories know or suspect its capacity has Dot Matrix LCD (192 x 65 Resolution) STD
can cause injury. Excess force can been exceeded. Dot Matrix LCD (168 x 48 Resolution) SLIM SLIM CW CCW
cause crowfoot or flare nut wrench • Do not force head of flex head drives • VIEWING DIRECTION: 6:00 ±2% ±3% of reading, 20% to 100%
slippage. against stops. • BACKLIGHT: WHITE (LED) Torque: of full scale
• Always adjust your stance to prevent (unflexed) ±4% ±6% of reading, 5% to 19%
• Read this manual completely before a possible fall should something give SEALED BUTTON PAD of full scale
using ELECTRONIC WRENCH. while using wrench. POWER - ON/OFF and torque and angle
• To insure accuracy, work must not • Do not attempt to recharge Alkaline re-zero
move in angle mode. cells. ENTER - measurement mode select and OPERATING TEMPERATURE
• For personal safety and to avoid • Store wrench in dry place. menu entry 0°F - 130°F (-18°C - 54°C)
wrench damage, follow good profes- • Remove batteries when storing UP – increments torque and angle settings
sional tool and fastener installation wrench used for periods longer than and menu navigation STORAGE TEMPERATURE
practices. 3 months. DOWN - decrements torque and angle set- 0°F to 130°F (-18°C to 54°C)
• Periodic recalibration is necessary to tings and menu navigation
maintain accuracy. WARNING. UNITS - units select: ft-lbs, in-lbs, in-oz MEASUREMENT DRIFT
• Wear safety goggles, user and Electrical Shock Hazard. (depending on range); kgm, kg-cm, dNm, ANGLE: -0.12 Angular Degrees per Degree C
bystanders. Electrical shock can cause injury. cNm (depending on range) and enter PSET TORQUE: +0.01% of reading per Degree C
• Be sure all components, including Metal handle is not isolated. (preset) menu
all adaptors, extensions, drivers Do not use on live electrical circuits. LCD BACKLIGHT – Illuminates all screens HUMIDITY
and sockets are rated to match or and last peak torque or angle recall Up to 90% non-condensing
exceed torque being applied. SAVE THESE INSTRUCTIONS
• Observe all equipment, system and FUNCTIONS BATTERY
manufacturer’s warnings, cautions and DISCLAIMER • Set - torque or angle target SLIM: Single “AA” Alkaline Cell
procedures when using this wrench. Operation of the wrench is not warranted in an • Track - real time display of torque or accumu- STD: Three “AA” Alkaline Cells
• Use correct size socket for fastener. EU member state if operating instructions are lated angular rotation with progress lights Alkaline or rechargeable NiMH batteries ex-
• Do not use sockets showing wear or not in that State’s language. • Peak Hold - 5 sec. flashing of peak torque or ceeds ASME battery life requirement of 10 hours
cracks. alternating peak torque/angle on release of continuous operation.
• Replace fasteners with rounded Contact BAHCO if a translation is needed. torque
corners. • Peak Recall - display last peak torque or peak DEFAULT AUTO SHUT-OFF
• To avoid damaging wrench: Never torque/angle on button press After 2 minutes idle –
use wrench with power off. Always • Memory - display of last 1500 peak torque or (Adjustable, see Advanced Settings)
turn ON wrench so applied torque is peak torque/angle readings
being measured.
• Do not press POWER while torque is ACCURACY
applied or while wrench is in motion. • Temperature: 22°C (72°F)
• Never use this wrench to break • Angle: ±1% of reading ±1º angular velocity
fasteners loose. > 10º/sec < 180º/sec
• Do not use extensions, such as a
pipe, on handle of wrench.
• Check that wrench capacity matches
or exceeds each application before
proceeding.

3
TAWM SERIES

USER INSTRUCTIONS
SLIM
BATTERY TORQUE AND/OR
CONDITION ANGLE DISPLAY PROGRESS LIGHTS
PROGRESS MODE ON/OFF AND INCREMENT MODE SELECT AND
FIGURE 1 LIGHTS COUNT RE-­ZERO BUTTON BUTTON MENU ENTRY BUTTON Yellow:
First light indicates 40% of
target torque or angle reached,
Second indicates 60% of
target reached,
Third indicates 80% of
AUDIBLE target reached.
ALERT Green:
Indicates target torque or angle
reached.
Red:
Indicates exceeded torque or
USB DATA STORAGE PROGRESS UNITS AND PRESET DECREMENT LCD BACKLIGHT angle target plus 4% or
CONNECTOR ALERT LIGHTS ENTRY BUTTON BUTTON AND PEAK exceeded maximum Preset
TORQUE/ANGLE target.
RECALL BUTTON

Install fresh Alkaline “AA” cells into handle of wrench.

WRENCH POWER ON SEQUENCE

Note: Do not turn on wrench while torque is applied, otherwise torque zero offset will be incorrect
and wrench will indicate a torque reading when torque is released. If this occurs, re-zero wrench by
momentarily pressing POWER button while wrench is on a stable surface with no torque applied.

1. Turn On Wrench.
While holding wrench still, press POWER button. BAHCO logo will be displayed followed by torque and
angle re-zeroing screens (if angle mode has been previously selected). If real-time-clock has not been Note: When date and time is set for first time, In-Service date is also set and is used for calculating
set, date and time entry screens are displayed (see Advanced Configuration section for entering date initial calibration interval (see “Setting Calibration Interval” in Advanced Configuration section).
and time). After entering date and time or if time has been previously set, target TORQUE or ANGLE Note: If wrench is powered up in torque only measurement mode, angle is not zeroed until mode is
screen will now be displayed (depending on previous measurement mode selected). changed to angle measurement mode, at which time torque and angle zeroing begins automatically
after 2 seconds. Wrench should be placed on a stable surface with no torque applied.
2. Select Measurement Mode. Note: Pressing ENTER button while angle is zeroing will abort zeroing function to allow user to
Toggle between target TORQUE and ANGLE screens by repeatedly pressing ENTER button. select another measurement mode.

STD TORQUE MODE

1. Set Target.
Use UP/DOWN buttons to change TORQUE target value.
2. Select Units of Measure.
Repeatedly press UNITS button while on target TORQUE screen until desired units are displayed.
3. Apply TORQUE.
Grasp center of handle and slowly apply torque to fastener until progress lights display green and a
½ second audible alert and handle vibration alerts you to stop.
4. Release TORQUE.
Note peak TORQUE reading flashing on LCD display for 5 seconds. Pressing BACKLIGHT button
while peak torque is flashing will continue to display value until button is released. Momentarily
pressing UP/DOWN, ENTER or UNITS button will immediately return to target TORQUE screen.
Reapplying TORQUE will immediately start another TORQUE measurement cycle.
5. Recall Peak TORQUE Reading.
To recall last peak TORQUE measurement, press and hold BACKLIGHT button for approximately 3
seconds. Peak TORQUE will flash for 5 seconds.

ANGLE MODE
Note: When angle measurement mode is selected for first time following a power on, “ANGLE
ZERO REQUIRED” message is displayed. After two seconds angle zero process begins and

5
TAWM SERIES

wrench must be placed on a stable surface. If ENTER button is pressed before two seconds to
change to torque only mode, angle zero process is skipped.

1. Set target. Use UP/DOWN buttons to change target ANGLE value.

2. Apply Torque and Rotate Wrench. Grasp center of handle and slowly apply torque to fastener and
rotate wrench at a moderate consistent speed until progress lights display green and a ½ second
audible alert and handle vibration alerts you to stop.
3. Release torque. Note alternating peak TORQUE and ANGLE readings flashing on LCD display for 5
seconds. Pressing BACKLIGHT button while peak values are flashing will continue to display values
until button is released. Momentarily pressing UP/DOWN, ENTER or UNITS button will immediately
return to target ANGLE screen. Reapplying torque (ratcheting) before target screen is displayed will
continue ANGLE accumulation as wrench is rotated.
4. Recall Peak ANGLE Reading. To recall last peak ANGLE measurement, press and hold BACKLIGHT
button for approximately 3 seconds. Peak TORQUE and ANGLE will be displayed alternately for 5
seconds.
3. Click “Open Folder” selection to display TORQLOG Character Separated Value (.csv) file.
MODE CYCLE COUNT
Mode cycle count feature is used to indicate number of times wrench has reached target torque in Note: If “AutoPlay” does not start automatically, use Explorer to display TORQLOG drive contents.
torque measurement mode or target angle in angle measurement mode.

STD / SLIM

TORQUE AND ANGLE MODE CYCLE COUNTING

1. Numerical counter located in top right of target torque or target angle screen will increment after each 4. Open file using Microsoft Excel by double clicking on file name (Example: “1213590002.CSV”) or
torque or angle cycle if applied torque or angle has reached target value. “drag and drop” file to computer.
2. When toggling between torque mode or angle mode using ENTER button or if target is changed, 5. Data on wrench can be cleared by deleting file on the TORQLOG drive.
numerical counter will reset back to 00. counter WILL NOT reset when re-zeroing, on menu entry/
exit or power down. Note: Wrench Serial Number and Calibration Date are included in first line of downloaded .csv file.
3. Memory icon will turn on indicating at least one torque or angle cycle data has been stored in memory. Example:

DATA DOWNLOAD
Torque and Angle data in memory can be downloaded to a computer via USB port.

Note: When downloading data from a wrench that has previous downloaded data, rename
previous file or move it to a different directory to prevent overwrite. However, Windows® will
notify user of duplicate file names and allow user to skip download, overwrite existing file or
save new file as a second copy.

1. Connect supplied USB cable from computer to wrench.

2. Computer will display “AutoPlay” window showing TORQLOG as a disk drive with option of using
Windows Explorer to view files:

7
TAWM SERIES

MAIN MENU
Main menu displays wrench operational information.
1. From target torque or angle screen, press and hold ENTER button for 3 seconds.
2. Use UP/DOWN buttons to highlight menu selection then press ENTER button.
Menu Selections:
EXIT - Exits Main menu and returns to target screen.
LANGUAGE - Displays language selection menu.
SET HEAD LENGTH - Displays wrench head length entry screen.
SHOW DATA - Displays stored torque and angle data.
CLEAR DATA - Clears stored torque and angle data.
CYCLE COUNT - Displays torque/angle cycle count screen.
SETTINGS - Displays advanced settings menu (see Advanced Settings Section). Note: For a fixed length head, head length entered is offset length measured from center of
CONFIGURE - Displays advanced configuration menu (see Advanced Configuration Section). drive to center of fastener.

SETTING HEAD LENGTH

Note: If wrench has an interchangeable head or an adapter or extension is added, length of
head, adapter and/or extension being used can be entered to correct for a different length
without requiring re-calibration.
Offset

1. To enter a head length, from target torque or angle screen, press and hold ENTER button for 3
seconds. Note: For an interchangeable head, head length is measured from locking pin to center of drive.
2. With SET HEAD LENGTH menu selection highlighted, momentarily press ENTER button. SET HEAD LENGTH is set during calibration. If a different length head is used, enter new head
3. Set Head Length screen is displayed next. Default head length is length of head at calibration length and offset is calculated automatically.
(zero for fixed head wrench) and is displayed with most-significant digit highlighted. Use UP/
DOWN buttons to increment/decrement head length. Pressing and holding UP/DOWN buttons will
progressively increment/decrement value faster.
4. Press ENTER button to accept digit and highlight next-significant digit.
5. Default units of length is in inches. Press UNITS button to change to millimeters.
6. Pressing ENTER button after least-significant digit is set returns to main menu. If length is changed
from default, «OFFSET IN USE» message will be displayed on target screen (on STD wrenches),
the target torque is highlighted in black (on SLIM wrenches). Note: For an interchangeable head with an adapter, head length entered is sum of head length
and offset length.
Note: If UP/DOWN buttons are pressed simultaneously while on the Set Head Length screen,
displayed head length resets to zero or calibration head length for interchangeable head
wrenches.

USE OF NEGATIVE OFFSETS

Note: Enter a negative value for offset when used in reverse direction with flex head or when
calculating sum of interchangeable head and offset lengths.

Offset

9
TAWM SERIES

When length of an offset (or sum of head minus offset for interchangeable head) is negative, maximum Example:
fastener target is limited by following formulas: 0002 = Show Data List Counter: TQ = Peak torque value
0001 = Show Data List Counter: TQ = Peak torque value: ANG = Peak angle value
STD 4. Pressing ENTER button while on Show Data screen returns to main menu.

135 Nm wrench: 340 Nm wrench: STD

Maximum Target Torque = offset *4,1 + 135 Maximum Target Torque = offset *6,1 + 340

Offset (cm) Max Target (Nm) Offset (cm) Max Target (Nm)
-1 131 -1 334
-2 127 -2 328
-3 123 -3 322
-4 119 -4 316
800 Nm wrench:
Maximum Target Torque = offset *7,6 + 800

Offset (cm) Max Target (Nm)

-1 792
-2 785
-3 777 SLIM
-4 770

SLIM

10 Nm wrench: 30 Nm wrench:
Maximum Target Torque = offset * 0.435 + 10 Maximum Target Torque = offset * 1.3 + 30

Offset (cm) Max Target (Nm) Offset (cm) Max Target (Nm)
-1 9.57 -1 28.70
-2 9.13 -2 27.40
-3 8.70 -3 26.10
-4 8.26 -4 24.80

Note: When using a negative offset, entering a target torque greater than maximum values
above may cause an overtorque error before reaching fastener target torque and possibly Note: A maximum of 1500 data records can be stored. Memory full icon will be displayed when
damage wrench. full and no more data is stored until memory is cleared (on STD wrenches only).
Note: A maximum of 1500 data records can be stored in memory. Memory full icon will be
VIEWING STORED TORQUE AND ANGLE DATA displayed when full. When full, a new data record will become record number 1500 and all older
Torque data is stored in memory after each torque cycle if applied torque has reached target value. data is shifted down one record number. Record 0002 becomes 0001 and old 0001 is dropped.
Torque and angle data is stored in memory after each angle cycle if applied angle has reached target
value. Memory Indicator is displayed when data is stored in non-volatile memory. DELETING STORED TORQUE AND ANGLE DATA
1. From target torque or angle screen, press and hold ENTER button for 3 seconds.
1. To view stored torque and angle data, from target torque or angle screen, press and hold ENTER 2. Highlight CLEAR DATA menu selection using UP/DOWN buttons then press ENTER button to
button for 3 seconds. display CLEAR ALL DATA screen.
2. Highlight SHOW DATA menu selection by pressing UP/DOWN buttons then press ENTER button to 3. In CLEAR ALL DATA screen, highlight YES menu selection to delete all stored data, or NO menu
display Show Data screen. selection to exit without deleting data.
3. In Show Data screen, scroll through each stored data record by pressing UP/DOWN buttons. 4. Press ENTER button after making selection.

11
TAWM SERIES

Note: If wrench is Locked (see Preset Lock in Advanced section), Clear Data function is disabled. Note: If wrench is Locked (see Preset Lock in Advanced section) Clear count function is disabled.

STD LANGUAGE
1. To select the language menu, press the ENTER button while LANGUAGE is highlighted then
highlight the desired language and press the ENTER button.
2. Decimal Mark selection menu is displayed. Decimal separator can be a comma or decimal point.
Use UP/DOWN buttons to select the decimal separator then press the ENTER button.

Note: The decimal separator will affect the formatting of the downloaded data when opened by
Excel depending on Windows® regional settings.

STD
SLIM

VIEWING AND CLEARING WRENCH CYCLE COUNTER

Each time torque or angle target is reached, wrench cycle counter is incremented. Maximum cycle
count is 999999. SLIM

1. From target torque or angle screen, press and hold ENTER button for 3 seconds.
2. Highlight CYCLE COUNT menu selection using UP/DOWN buttons.
3. Press ENTER button to display CYCLE COUNT screen.
4. To exit CYCLE COUNT screen without clearing count, press ENTER button while EXIT menu
selection is highlighted.
5. To reset wrench cycle count to 0, highlight CLEAR menu selection then press ENTER button.
6. EXIT menu selection is automatically highlighted after count is cleared. Press ENTER button to
return to main menu.

STD

3. To exit Main menu and return to target torque or angle screen, press ENTER button while EXIT
menu selection is highlighted.

TARGET PRESETS (PSET)

PSET function gives user ability to configure 50 preset target torque or target angle settings, each with
a target, minimum, maximum (over range) and batch count value. PSETs are stored in non-volatile
memory so that they are retained while power is off.
SLIM
Note: After adding a Preset (see below), navigate between manual target torque, angle mode
and PSET screen by repeatedly pressing ENTER button. While PSET screen is displayed, press
UP/DOWN buttons to select additional configured PSETs.

13
TAWM SERIES

STD 6. MAXIMUM TORQUE screen is displayed next. MAXIMUM TORQUE is torque value above which
red progress lights turn on. Initial MAXIMUM TORQUE value will be TARGET TORQUE value plus
positive torque tolerance (default 4%, see MODE SETUP in Advanced Configuration section).
Maximum torque value can be set greater than TARGET TORQUE value to 10% above wrench
maximum range by pressing UP/DOWN buttons. Once desired maximum torque value has been set,
press ENTER button.
7. BATCH COUNT screen is displayed next. Default value is zero. Batch count range is 0 to 99. Press
UP/DOWN buttons to increment/decrement batch count. Mode Count increments each time target
torque is reached if a batch count of zero is entered. Mode Count decrements if a non-zero batch
count is entered and resets to batch count value when count reaches zero. Once desired batch
count value has been set, press ENTER button.
8. PSET target screen is displayed labeled with next available PSET number from 01 to 50.
9. To enter additional torque presets, repeatedly press ENTER button until target torque screen is dis-
played and repeat steps above.

STD

SLIM

SLIM

ADDING A TORQUE PRESET

1. From manual target torque screen, select units of measure.
2. Press and hold UNITS button for 3 seconds.
3. ADD PRESET confirmation screen is displayed. Highlight YES menu selection using UP/DOWN
buttons then press ENTER button. NO menu selection returns to main menu without adding a PSET.
4. TARGETTORQUE screen is displayed. TARGET TORQUE is target value of fastener. Initial TARGET ADDING AN ANGLE PRESET
TORQUE value is value from target torque screen. TARGET TORQUE can be set to any value within 1. From manual target angle screen, press and hold UNITS button for 3 seconds.
wrench torque range by pressing UP/DOWN buttons. Once desired target torque value has been 2. ADD PRESET confirmation screen is displayed. Highlight YES menu selection using UP/DOWN buttons
set, press ENTER button. then press ENTER button. NO menu selection returns to main menu without adding a PSET.
5. MINIMUM TORQUE screen is displayed. MINIMUM TORQUE is value at which green progress 3. TARGET ANGLE screen is displayed. TARGET ANGLE is fastener rotational angle target value. Initial
lights, audible alert and vibrator turn on. Initial MINIMUM TORQUE value is TARGET TORQUE value TARGET ANGLE value is value from target angle screen. TARGET ANGLE can be set from 0 to 360° by
minus negative torque tolerance (default 0%, see MODE SETUP in Advanced Configuration section). pressing UP/DOWN buttons. Once desired target angle value has been set, press ENTER button.
MINIMUM TORQUE can be set to any value from TARGET TORQUE to wrench minimum torque range 4. MINIMUM ANGLE screen is displayed. MINIMUM ANGLE is value at which green progress lights, au-
by pressing UP/DOWN buttons. Once desired minimum torque value has been set, press ENTER button. dible alert and vibrator turn on. Initial MINIMUM ANGLE value is TARGET ANGLE minus negative angle

15
TAWM SERIES

tolerance (default 0%, see MODE SETUP in Advanced Configuration section). MINIMUM ANGLE can be 3. Highlight EDIT selection using UP/DOWN buttons then press ENTER button.
set from 0 to TARGET ANGLE by pressing UP/DOWN buttons. Once desired minimum angle value has 4. TARGET TORQUE or TARGET ANGLE screen is displayed. Value can be changed by pressing UP/
been set, press ENTER button. DOWN buttons. Once desired target torque or angle value has been set, press ENTER button.
5. MAXMUM ANGLE screen is displayed next. MAXIMUM ANGLE is angle value above which red progress 5. MINIMUM TORQUE or MINIMUM ANGLE screen is displayed. Value can be changed by pressing
lights turn on. Initial MAXIMUM ANGLE value will be TARGET ANGLE plus positive angle tolerance (de- UP/DOWN buttons. Once desired torque or angle value has been set, press ENTER button.
fault 4%, see MODE SETUP in Advanced Configuration section). MAXIMUM ANGLE value can be set to 6. MAXMUM TORQUE or MAXIMUM ANGLE screen is displayed next. Value can be changed by
any value greater than TARGET ANGLE by pressing UP/DOWN buttons. Once desired value has been pressing UP/DOWN buttons. Once desired torque or angle value has been set, press ENTER button.
set, press ENTER button. 7. BATCH COUNT screen is displayed next. Value can be changed by pressing UP/DOWN buttons.
6. BATCH COUNT screen is displayed next. Default value is zero. Batch count range is 0 to 99. Press UP/ Once desired batch count value has been set, press ENTER button.
DOWN buttons to increment/decrement batch count. Mode Count increments each time target angle is 8. PSET target screen is displayed labeled with same PSET number.
reached if a batch count of zero is entered. Mode Count decrements if a non-zero batch count is entered
and resets to batch count value when count reaches zero. Once desired batch count value has been set, STD
press ENTER button.
7. PSET target screen is displayed labeled with next available PSET number from 01 to 50.
8. To enter additional angle presets, repeatedly press ENTER button until target angle screen is displayed and
repeat steps above.

STD

SLIM

SLIM

Note: Pressing ENTER button while EXIT menu selection is highlighted will exit without editing
PSET.

DELETING A PRESET
Delete PSET function allows user to remove stored presets from wrench
EDITING A PRESET 1. From Preset screen to be deleted, press and hold UNITS button for 3 seconds.
Edit PSET function gives user ability to edit stored PSETS on wrench. 2. CHANGE PRESET screen is displayed.
1. From Preset screen to be edited, press and hold UNITS button for 3 seconds. 3. Highlight DELETE menu selection using UP/DOWN buttons and press ENTER button.
2. CHANGE PRESET screen is displayed. 4. Target screen is displayed and deleted PSET is no longer available for selection.

17
TAWM SERIES

Note: Pressing ENTER button while EXIT menu selection is highlighted will exit without deleting PSET. SLIM
Note: When a PSET is deleted, all other stored PSET’s will retain their original PSET numbers.
When a new PSET is entered, it will be assigned first available PSET number in sequence.

STD SLIM

Note: All user configurable settings are stored in non-volatile memory and are retained while
power is off.

SHOW INFO
Show Info menu selection displays wrench operational information.

1. From Settings menu, press ENTER button while SHOW INFO selection is highlighted.
2. SHOW INFO screen is displayed.
3. UP/DOWN buttons are used to scroll screen.
Operational Information:
ADVANCED SETTINGS SN: Serial number assigned to wrench.
CAL: Date of last wrench calibration.
Advanced settings are accessed from SETTINGS menu selection on main menu. ISD: In-Service Date.
TCF: Torque Calibration Factor.
1. From target torque or angle screen, press and hold ENTER button for 3 seconds. ACF: Angle Calibration Factor.
2. Highlight SETTINGS menu selection using UP/DOWN buttons. VER: Software version.
3. Press ENTER button to display Settings menu. OVR CNT: Overtorque Counter tracks how many times an over-torque event occurred on wrench
Menu Selections: (torque >125% of full scale).
EXIT - Exits Settings menu and returns to target screen. AZZ: Angle Z-Axis Zero Offset (only on SLIM wrenches).
SHOW INFO - Displays wrench operational information. AZX: Angle X-axis Zero Offset (only on SLIM wrenches).
SLEEP TIME - Displays power down interval setup screen. AZO: Angle Zero Offset at full scale torque (only on SLIM wrenches).
LCD CONTRAST - Displays LCD contrast setup screen. TFS: Torque full scale value (only on SLIM wrenches).
KEY BEEP - Displays button press beep enable/disable setup screen. Copyright (only on SLIM wrenches).
TARGET BEEP - Displays target beep enable/disable setup screen (only on SLIM wrenches). TQZ: Torque Zero Offset.
AUTO BACKLIGHT - Displays auto backlight enable/disable screen to turn on backlight during ANZ: Angle Zero Offset (only on SLIM wrenches).
measurement. 4. Pressing ENTER button exits Show Info screen and returns to Settings menu.
TOGGLE BACKLGHT - Displays BACKLIGHT button toggle or timeout enable/disable screen.
VIBRATOR CONFIG - Displays vibrator ON/OFF configuration for when target reached. STD SLIM
BATTERY TYPE - Displays the battery type selection screen (only on SLIM wrenches).
4. To exit Settings menu and return to target torque or angle screen, press ENTER button while EXIT
menu selection is highlighted.

STD

19
TAWM SERIES

SETTING SLEEP TIME KEY BEEP SETUP

This function will allow user to set interval wrench enters power-down state following last applied This function will allow user to enable or disable audio feedback when a button is pressed.
torque or button press.
1. From Settings menu, use UP/DOWN buttons to highlight KEY BEEP selection then press ENTER
1. From Settings menu, use UP/DOWN buttons to highlight SLEEP TIME selection then press button.
ENTER button. 2. KEY BEEP screen is displayed.
2. SLEEP TIME screen is displayed. 3. Use UP/DOWN buttons to highlight ENABLE (factory default) or DISABLE selection.
3. Use UP/DOWN buttons to select sleep interval. 4. Press ENTER button to accept selection and exit to Settings menu.
Selectable Intervals: 2 MIN (factory default); 5 MIN; 10 MIN; 30 MIN; 1 HR; 2 HR; 8 HR
4. Press ENTER button to accept selection and exit to Settings menu. STD SLIM

STD SLIM

TARGET BEEP SETUP (ONLY ON SLIM WRENCHES)

This function will allow user to enable or disable audio feedback when target is reached.

SETTING LCD CONTRAST 1. From Settings menu, use UP/DOWN buttons to highlight TARGET BEEP selection then press
This function will allow user to set LCD contrast for optimal viewing. ENTER button.
2. TARGET BEEP screen is displayed.
1. From Settings menu, use UP/DOWN buttons to highlight LCD CONTRAST selection then press 3. Use UP/DOWN buttons to highlight ENABLE (factory default) or DISABLE selection.
ENTER button. 4. Press ENTER button to accept selection and exit to Settings menu.
2. CONTRAST screen is displayed.
3. Use UP/DOWN buttons while viewing display to change contrast to desired level.
Selectable levels: 20 to 80 in increments of 5 (factory default = 40).
4. Press ENTER button to accept selection and exit to Settings menu.

STD SLIM

AUTO BACKLIGHT SETUP

This function will allow user to enable or disable backlight from turning on during torque or angle measurement.

1. From Settings menu, use UP/DOWN buttons to highlight AUTO BACKLIGHT selection then press
ENTER button.

21
TAWM SERIES

2. AUTO BACKLIGHT screen is displayed. VIBRATOR CONFIGURATION

3. Use UP/DOWN buttons to highlight ENABLE (factory default) or DISABLE selection. This function will allow user to configure vibrator for On or Off when target is reached for preference
4. Press ENTER button to accept selection and exit to Settings menu. and/or battery power savings.

STD SLIM 1. From Settings menu, use UP /DOWN buttons to highlight VIBRATOR CONFIG selection, then
press ENTER button.
2. VIBRATOR CONFIG screen is displayed.
3. Use UP /DOWN buttons to toggle ON or OFF selection.
4. Press ENTER button to accept selection and exit to Settings menu.

STD SLIM

TOGGLE BACKLIGHT SETUP

This function will allow user to enable or disable backlight toggle function. If toggle mode is disabled,
BACKLIGHT button turns on backlight and it automatically turns off after five seconds following any
last button press. If toggle mode is enabled, a BACKLIGHT button press will turn on backlight and it will
remain on until next BACKLIGHT button press.

1. From Settings menu, use UP/DOWN buttons to highlight TOGGLE BACKLGHT selection then press
ENTER button. BATTERY TYPE SELECTION (ONLY ON SLIM WRENCHES)
2. TOGGLE BACKLGHT screen is displayed. This function will allow user to configure the battery discharge thresholds for the type of battery used.
3. Use UP/DOWN buttons to highlight ENABLE or DISABLE (factory default) selection. 1. From Settings menu, use UP /DOWN buttons to highlight BATTERY TYPE selection then press
4. Press ENTER button to accept selection and exit to Settings menu. ENTER button.
2. BATTERY TYPE screen is displayed.
Note: Backlight will turn off when wrench powers down either by POWER button press or sleep time. 3. Use UP /DOWN buttons to select the type of battery being used.
Note: If toggle backlight is enabled and backlight is on, backlight will remain on during and after 4. Press ENTER button to accept selection and exit to Settings menu.
applying torque.

STD SLIM

Note: Wrench is configured for Alkaline battery shipped from factory. If Alkaline battery is replaced
with rechargeable Nickel-Metal Hydride (NIMH) or lithium, battery type should be changed so battery
level icon and LOW battery warnings function optimally. Battery life (REPLACE) will not be impacted,
however 50% and Low will be optimized to show most accurate linear discharge time.

23
TAWM SERIES

ADVANCED CONFIGURATION
ANG+% SETUP - Displays target torque plus tolerance entry screen.
Advanced configuration is accessed from CONFIGURE menu selection on main menu. THEN DISABLED - Displays THEN Mode enable/disable screen.
AND DISABLED - Displays AND Mode enable/disable screen.
Note: If wrench has been locked (see Preset Lock and Job Mode), a password entry is required 3. Use UP/DOWN buttons to highlight menu selections.
to enter Configure menu. 4. Press ENTER button while EXIT menu selection is highlighted to return to Configure menu.

1. From target torque or angle screen, press and hold ENTER button for 3 seconds. STD SLIM
2. Highlight CONFIGURE menu selection using UP/DOWN buttons.
3. Press ENTER button to display Configure menu.
Menu Selections:
EXIT - Exits Configure menu and returns to target torque or angle screen.
MODE SETUP - Displays wrench mode setup menu.
PRESET LOCK - Displays Preset lock menu.
DELETE PRESETS - Displays delete all presets menu. SETTING TARGET TOLERANCES
JOB MODE - Displays Job mode menu. This function will allow user to set plus and minus tolerances for torque and angle targets.
CALIBRATION - Displays wrench calibration menu (password protected). Note: These tolerances are used for manual modes only. Preset tolerances are defined by Mini-
SET DATE/TIME - Displays clock date and time entry screens. mum and Maximum values.
SET CAL INTRVAL - Displays calibration interval setup screen (requires clock date and time setup).
CAL COUNT DOWN - Displays calibration needed countdown setup screen (requires clock date and 1. From Mode Setup menu, use UP/DOWN buttons to highlight tolerance selection to setup (TQ-%,
time setup and calibration interval setup) (only on SLIM wrenches). TQ+%, ANG-% ANG+%) then press ENTER button.
CHANGE PASSWD - Displays change password menu. 2. Tolerance screen is displayed.
ASSET # - Displays user configurable 15-character string (only on SLIM wrenches). 3. Use UP/DOWN buttons to change tolerance value. Range is 0 to 10% ( factory default for minus
4. To exit Configure menu and return to target torque or angle screen, press ENTER button while tolerance is 0% and 4% for plus tolerance).
EXIT menu selection is highlighted. 4. Press ENTER button to accept selection and exit to Mode Setup menu.

STD SLIM STD SLIM

Note: All user configurable settings are stored in non-volatile memory and are retained while
power is off. Note: Green progress lights turn on at target minus -% TOL.
Note: Red progress lights turn on above target plus +% TOL.
MODE SETUP Note: Plus tolerance is added to minimum Preset value to define initial maximum value when a
Mode setup menu allows user configure target torque and angle minus and plus tolerances and enable/ Preset is first added.
disable Torque THEN Angle mode and Torque AND angle mode.
ENABLE/DISABLE TORQUE THEN ANGLE MODE
1. From Configure menu, press ENTER button while MODE SETUP selection is highlighted. This function will allow user to enable or disable Torque THEN Angle Mode.
2. Mode Setup menu is displayed.
Menu Selections: 1. From Mode Setup menu, use UP/DOWN buttons to highlight THEN DISABLED (factory default)
EXIT - Exits Mode setup menu and returns to Configure menu screen. selection then press ENTER button.
TQ-% SETUP - Displays target torque minus tolerance entry screen. 2. TQ THEN ANGLE enable/disable screen is displayed.
TQ+% SETUP - Displays target torque plus tolerance entry screen. 3. Use UP/DOWN buttons to select ENABLE or DISABLE selection.
ANG-% SETUP - Displays target torque minus tolerance entry screen. 4. Press ENTER button to accept selection and exit to Mode Setup menu.

25
TAWM SERIES

STD Note: UNITS button can be used to select torque units while on Torque THEN Angle screen.
Note: Torque cycle is not recorded in memory unless both torque and angle reach targets.
Note: Red progress lights turn on if torque exceeds 110% of wrench full scale or if angle exceeds
target + plus tolerance while in manual mode.
Note: Torque THEN Angle Presets are entered by pressing and holding Units button while on
Torque THEN Angle screen. MAXIMUM TORQUE defaults to full range plus 10%. Refer to “Adding
a Torque Preset” and “Adding an Angle Preset” in Basic section for parameter entry.

ENABLE/DISABLE TORQUE AND ANGLE MODE

This function will allow user to enable or disable Torque AND Mode.

1. From Mode Setup menu, use UP/DOWN buttons to highlight AND DISABLED (factory default)
selection then press ENTER button.
SLIM 2. TQ AND ANGLE enable/disable screen is displayed.
3. Use UP/DOWN buttons to select ENABLE or DISABLE selection.
4. Press ENTER button to accept selection and exit to Mode Setup menu.

STD

Note: Menu selection indicates current configuration (ENABLED or DISABLED).

TORQUE THEN ANGLE MODE

Torque THEN Angle mode is setup by first setting a target torque and units then a target angle before
selecting Torque THEN Angle mode. In Torque THEN Angle mode, when applied torque reaches target
torque, wrench automatically switches to angle mode for angle measurement. Progress lights indicate SLIM
applied torque progress while torque is measured and angle when angle is measured. If torque is below
target torque when angle reaches target angle, green progress lights will not turn on and if angle exceeds
maximum angle, red progress lights turn on indicating a potential problem with fastener.

1. From target torque screen, use UP/DOWN buttons to set target torque and UNITS button to select
torque measurement units then press ENTER button.
2. Angle target screen is displayed. Use UP/DOWN buttons to set target angle then press ENTER button.
3. Torque THEN Angle mode screen is displayed.
4. Apply torque until target is reached then rotate wrench to target angle.

STD
Note: Menu selection indicates current configuration (ENABLED or DISABLED).

TORQUE AND ANGLE MODE

Torque AND Angle mode is setup by first setting a target torque and units then a target angle before selecting
SLIM Torque AND Angle mode. In Torque AND Angle mode, torque and angle are measured simultaneously.
Yellow progress lights track torque measurement. When both torque and angle reach their targets, green
progress lights turn on and torque and angle data record is stored. If either of measurements exceed their
upper tolerance, red progress lights turn on.

27
TAWM SERIES

1. From target torque screen, use UP/DOWN buttons to set target torque and UNITS button to select SLIM
torque measurement units then press ENTER button.
2. Angle target screen is displayed. Use UP/DOWN buttons to set target angle then press ENTER
button until Torque AND Angle mode screen is displayed.
3. Apply torque and rotate wrench until both targets are reached.

STD

SLIM
Note: If LOCK is selected without a Preset configured, following screen is displayed:

STD SLIM
Note: UNITS button can be used to select torque units while on Torque AND Angle screen.
Note: Torque THEN Angle Presets are entered by pressing and holding Units button while on
Torque THEN Angle screen. Refer to “Adding a Torque Preset” and “Adding an Angle Preset” in
Basic section for parameter entry.
Note: Torque cycle is not recorded in memory unless both torque and angle reach targets. Note: When Preset Lock is enabled, Clear Memory function is disabled and displays following
Note: Red progress lights turn on if torque exceeds target + plus tolerance or if angle exceeds Locked message if attempted:
target + plus tolerance while in manual mode.
Note: Red progress lights turn on if torque exceeds maximum torque or if angle exceeds maxi- STD SLIM
mum angle in Preset mode.

PRESET LOCK
Preset Lock function allows user to lock wrench so that only configured presets are accessible. No other Note: When Preset Lock is enabled, Clear Cycle count function is disabled and displays Locked
presets can be configured and manual target torque and angle modes are not accessible when locked. message if attempted.

Note: Password entry is required to enable Preset Lock. When locked, password entry is required PRESET UNLOCK
to re-enter Configure menu (Refer to Calibration Manual regarding Configure password). When Preset Lock is enabled, a password is required to access Configure menu. Refer to Calibration
Manual for Configure password.
1. From Configure menu, use UP/DOWN buttons to highlight PRESET LOCK selection then press
ENTER button. 1. From target torque or angle screen, press and hold ENTER button for 3 seconds.
2. Preset Lock enable/disable screen is displayed. 2. Highlight CONFIGURE menu selection using UP/DOWN buttons.
3. Use UP/DOWN buttons to select LOCK or UNLOCK selection. 3. Press ENTER button to display Password screen.
4. Press ENTER button to accept selection and exit to Configure menu. 4. Follow password entry procedure found in Calibration manual.

STD STD

29
TAWM SERIES

SLIM STD

DELETE PRESETS
Delete Presets function allows user to delete all presets at once.
1. From Configure menu, use UP/DOWN buttons to highlight DELETE PRESETS selection then
press ENTER button.
2. Delete Presets confirmation screen is displayed.
3. Use UP/DOWN buttons to select YES or NO selection. SLIM
4. Press ENTER button to accept selection and exit to Configure menu.

STD SLIM

Note: Text “JOB” is displayed between PSET number and batch count when enabled.
Note: If Delete Presets is selected without a Preset configured, following screen is displayed:

STD SLIM

CALIBRATION
JOB MODE Calibration menu is password protected. Refer to Calibration Manual.
Job Mode function allows user to enable or disable wrench preset Job mode. When in Job mode,
wrench executes presets in order configured and automatically switches to next preset when batch STD SLIM
count reaches zero. When in Job mode wrench is locked and Preset lock icon is displayed.

Note: Password entry is required to enable Job Mode. When enabled, password entry is re-
quired to re-enter Configure menu (Refer to Calibration Manual for Configure password).
SETTING DATE AND TIME
1. From Configure menu, use UP/DOWN buttons to highlight JOB MODE selection then press ENTER button. Set Date/Time function allows user to set real-time-clock date and time for time stamping data records,
2. Job Mode enable/disable screen is displayed. recording last calibration date and notifying user of an expired calibration interval.
3. Use UP/DOWN buttons to select ENABLE or DISABLE.
4. Press ENTER button to accept selection and exit to Configure menu. Note: When date and time is set for first time, In-Service date is also set and is used for calculating
initial calibration interval (see “Setting Calibration Interval” in Advanced Configuration section).

31
TAWM SERIES

1. From Configure menu, use UP/DOWN buttons to highlight SET DATE/TIME selection then press 2. CAL INTERVAL screen is displayed.
ENTER button. 3. Use UP/DOWN buttons to change calibration interval.
2. SET DATE screen is displayed with year highlighted. Selectable Intervals: 12 MON (factory default); 6 MON; 3 MON; DISABLED
3. Use UP/DOWN buttons to set year then press ENTER button to highlight month. 4. Press ENTER button to accept selection and exit to Configure menu.
4. Use UP/DOWN buttons to set month then press ENTER button to highlight day.
5. Use UP/DOWN buttons to set day then press ENTER button. STD SLIM
6. SET TIME screen is displayed with hour highlighted.
7. Use UP/DOWN buttons to set hour then press ENTER button to highlight minutes.
8. Use UP/DOWN buttons to set minutes then press ENTER button to highlight seconds.
9. Use UP/DOWN buttons to set seconds then press ENTER button.
10. Clock is set and Configure menu is displayed.

STD

Note: Clock Date and Time must be set before calibration interval will function. If batteries are
removed from wrench for longer than 20 minutes, clock will revert to default settings and must
be re-entered at power on.
Note: Calibration interval is calculated from either IN-Service Date or last Calibration date (see
SHOW INFO menu) depending on which is more recent date. When clock Date is greater than
IN-Service or Last Calibration date, plus Cal Interval, “CAL NEEDED” message will be displayed
on power up and after a re-zero. Pressing ENTER button will continue to target menu. Applying
torque while “CAL NEEDED” message is displayed will immediately display torque or angle
measurement and return to target menu when released.
Note: As an alternative to calibration interval, a Calibration Cycle Counter is provided in Calibration
menu (Refer to Calibration Manual regarding Calibration menu). Each time a measurement cycle
reaches target torque, calibration cycle counter is incremented. When torque is recalibrated,
SLIM calibration counter is automatically reset to zero. User can disable calibration interval check and
use number of cycles since last calibration to decide when to recalibrate.
Note: If an invalid date is entered and Calibration interval is enabled, an unintended “CAL NEEDED”
message may be displayed. Either disable the calibration interval or enter a correct date.

SETTING CALIBRATION NEEDED COUNTDOWN (ONLY ON SLIM WRENCHES).

This function will allow user to set number of days when “CAL NEEDED” message will be displayed along
with days remaining before a wrench lock out occurs due to Cal interval expiring.

1. From Configure menu, use UP/DOWN buttons to highlight CAL COUNTDOWN selection then press
ENTER button.
2. CAL COUNTDOWN screen is displayed.
Note: Year selection will scroll up from 2013. Month selection will scroll from 1 to 12. Day selection will 3. Use UP/DOWN buttons to change calibration countdown.
scroll from 1 to 31. Range: 0 to 10 days.
Note: Hour selection will scroll through 0 to 23. Minute and Second selections will scroll through 0 to 59. 4. Press ENTER button to accept selection and exit to Configure menu.
Note: If batteries are removed from wrench for longer than 20 minutes, clock will revert to default set-
tings and must be re-entered at power on.

SETTING CALIBRATION INTERVAL

This function will allow user to set calibration interval for when “CAL NEEDED” message will be displayed.

1. From Configure menu, use UP/DOWN buttons to highlight SET CAL INTRVAL selection then press
ENTER button.

33
TAWM SERIES

Note: Clock Date and Time must be set and Cal interval enabled before calibration countdown Note: Pressing POWER button at any time aborts password change sequence.
will function (see Setting Date and Time and Setting Calibration Interval).
Note: Calibration Countdown is number of days before wrench is locked out from use following Note: If an invalid password is entered during the confirmation step, Invalid Password Match
an expired Cal interval. Countdown number of days before lockout is displayed below “CAL screen is displayed and new password is not accepted.
NEEDED” message:
STD SLIM

Note: “CAL NEEDED” message will be displayed on power up and after a re-zero. Applying
torque while countdown is remaining, torque or angle is immediately displayed. Red LEDs and
buzzer turn on if Cal interval has expired. Pressing ENTER button after Cal interval has expired ASSET # (ONLY ON SLIM WRENCHES)
will display Password Entry screen (Refer to TAWM Calibration manual). This function displays a USB configurable 15-character string. When configured, Asset # string is down-
Note: An entered Cal Countdown value of 0 days will disable calibration countdown and if Cal load data file name and is included in first row of.csv data file.
interval is enabled, wrench does not lock when CAL NEEDED” message is displayed.
1. From Configure menu, use UP/DOWN buttons to highlight ASSET # selection then press ENTER
CHANGE PASSWORD button.
Change Password function allows user to change password to a new password. Default password is 2. ASSET # screen is displayed.
required to initially change the password (Refer to Calibration Manual for Configure password). 3. Use Windows program to configure Asset # via USB (Contact factory for software).
4. Press ENTER button to accept selection and exit to Configure menu.
1. From Configure menu, use UP/DOWN buttons to highlight CHANGE PASSWD selection then press
ENTER button.
2. Initial password entry screen is displayed.
3. Enter default password if changing for first time, otherwise enter current user password using UP/
DOWN buttons to change each digit followed by ENTER button.
4. Change password entry screen is displayed.
5. Enter new password using UP/DOWN buttons to change each digit followed by ENTER button.
6. Confirm password entry screen is displayed.
7. Re-enter new password using UP/DOWN buttons to change each digit followed by ENTER button. Note: While Asset # is being displayed, number can be configured via USB.
Note: Available characters for Asset #: 0-9, A-Z, space # _ % ‘ ( ) + , - .
STD Note: If Asset # is blank, wrench serial number is used for .csv file name and included in data.

SLIM

35
TAWM SERIES

TROUBLESHOOTING IMPORTANT INFORMATION

Note: If any of following issues persist, return wrench to a SNA Europe/Bahco repair center. USE OF ADAPTORS, EXTENSIONS AND - Wrench must be held still during angle
UNIVERSALS zeroing. Motion is indicated by alternating
Anytime an adaptor, extension or universal is used dashes “- -” on display
ISSUE POSSIBLE CAUSE RESOLUTION with a torque wrench in such a way that fastener - Remove battery when stored for extended
distance is different than torque wrench square drive periods (Note: clock will revert to default set-
Dead/No batteries Replace batteries
Wrench does not turn on when distance at calibration, an adjustment to head length tings).
POWER button pressed. Software glitch Cycle power using end-cap is required to get a proper fastener torque reading.
When using wobble extension or a universal, do BATTERY REPLACEMENT
Calibration required Recalibrate
Torque reading out of spec. not exceed more than 15 degrees of offset from Note: When replacing batteries, real-time-clock
Incorrect head length entered Enter correct offset head length perpendicular drive. Do not use a long extension will maintain date and time for 20 minutes.
with flex-drive at full flex. Note: Turn end cap counter-clockwise to unscrew.
Clear data, re-enter settings and press
Wrench did not retain settings Batteries removed before setting were
and hold POWER button to power down
while batteries were removed. saved in non-volatile memory.
wrench before removing batteries. CALIBRATION Batteries should be installed in carrier prior to car-
Contact your Bahco sales representative for rier installation into wrench. Battery negative con-
Press ENTER button to continue using calibration services or refer to Calibration Manual. tacts should be oriented with carrier springs.
LOW BATTERY Low battery
wrench and replace batteries soon.

CERTIFICATION Replace SLIM models with one single “AA” cell only
Press POWER button to turn off wrench This torque-angle wrench was calibrated at factory
REPLACE BATTERY Dead battery
and replace batteries.
using angular displacement and torque measure-
Torque applied while zeroing Remove torque and re-zero
ment instruments that are traceable to National
Institute of Standards and Technology (N.I.S.T.). Unscrew end cap. Insert new cell
Negative (-) end Into end cap
Wrench over torqued Recalibrate Torque parameters comply with ISO 6789:2003 and
TORQUE ZERO
ERROR
Wrench improperly calibrated Recalibrate ASME B107:300-2010 (B107.29). Note: no U.S. or Replace STD models with three “AA” cells only.
International Standards exist for angle wrenches.
Torque sensor failure Return to Factory Angle calibration was performed on an angle gage
Wrench moving during zeroing Place wrench on stable surface with ±1 degree accuracy at each 45 degree in-
ANGLE ZEROING Unscrew end cap. Insert new cells
-- dexing point throughout 180 degrees of rotation. Positive (+) end into handle first
SET STILL Gyro unstable Return to Factory 100% BATTERY LEVEL

IMPORTANT!
ENTER button pressed during angle Calibration events are recorded in wrench 50% BATTERY LEVEL
ANGLE ZERO zeroing (Aborted zeroing to access Press POWER button to re-zero
ERROR memory which provides evidence to void factory
menus)
certification.
LOW BATTERY
LOW BATTERY
Cycle power using POWER button and MAINTENANCE / SERVICE
OVERTORQUE Over 125% of full scale torque applied
recalibrate
Clean wrench by wiping with a damp cloth. DO REPLACE BATTERY
REPLACE BATTERY

NOT use solvents, thinners or carburetor cleaners.

ANGLE Wrench rotated too fast during angle Note: When Replace Battery screen is displayed
measurement
Press POWER button to re-zero DO NOT immerse in anything.
ERROR
Service and repairs are to be done by SNA wrench will no longer operate until batteries are
Calibration interval exceeded or invalid Calibrate wrench or press ENTER to Europe/Bahco Service Center only. Contact your replaced. Only POWER button functions which
CALL date entered with calibration interval continue. Disable calibration interval if Bahco Torque Products representative. immediately turns off wrench.
NEEDED
enabled not required. Ratchet head repair kits can be ordered from a
Bahco Representative. MEMORY INDICATORS
Clear data memory
Memory error
DATA IN MEMORY
NOTES: Less than 1500 torque and angle records
stored in memory.
- If display shows persistent “TORQUE ZERO
Calibrate torque MEMORY FULL
torque ucal Torque uncalibrated ERROR” at power on, wrench is damaged 1500 torque or angle records stored in memory.
New records will not be recorded until memory is cleared
and must be returned for repair. (on STD wrenches only).
New data will replace oldest record until memory is
- If display shows “ANGLE ERROR” in angle cleared (on SLIM wrenches only)
Calibrate angle
angle ucal Angle uncalibrated mode, fastener rotation speed has exceeded MEMORY ERROR
Memory read or write error.
capacity of wrench.

37
TAWM SERIES

2018/11/5
(ENG) EC DECLARATION OF CONFORMITY (DEN) EF-VERENSSTEMMELSESERKLÆRING
(FRA) DÉCLARATION DE CONFORMITÉ CE (NOR) ECSAMSVERKLARING
(ESP) DECLARACIÓN DE CONFORMIDAD DE LA CE (FIN) EY-VAATIMUSTENMUKAISUUSVAKUUTUS
(POR) DECLARAÇÃO DE CONFORMIDADE EC (RUS) Декларация о соответствии EC
(ITA) DICHIARAZIONE DI CONFORMITA’ CE (TUR) CE STANDARDİZASYON BEYANI
(GER) EG-KONFORMITÄTSERKLÄRUNG (CZE) PROHLÁŠENÍ O SHODĚ
(NED) EG- VERKLARING VAN OVEREENSTEMMING (SVK) PREHLÁSENIE O ZHODE
(POL) EC DEKLARACJA ZGODNOŚCI (GRE) ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΜΕ ΕΕ
(SWE) CE DEKLARATION
(ENG) Hereby declares that: / The device: (DEN) Erklærer herved at: / enheten:
(FRA) Déclare par la présente que: / L´appareil: (NOR) Erklærer herved at: / enheten:
(ESP) Declaro que: / El aparato: (FIN) Vakuutamme täten: / Että tuote:
(POR) Vimos por este meio declarar: / O aparéelo: (RUS) Настоящим заявляем, что: / Устройство:
(ITA) Con la presente dichiaro che: / Dispositivo: (TUR) Beyan ederiz ki: / Cihaz:
(GER) Hiermit wird erklärt, dass: / Die folgenden Erzeugnisse: (CZE) Níže prohlašujeme, že: / výrobek:
(NED) Hierbij verklaart dat: / Het apperaat: (SVK) Týmto prehlasujeme, že : / Výrobok:
(POL) Niniejszym oświadcza, że: / Urządzenia: (GRE) Δηλώνει ότι: / Η συσκευή:
(SWE) Härmed deklareras att: / Enheten:

(ENG) Type(s) (ENG) Product Electronic Torque and angle Wrench (ENG) Year
(FRA) Type(s) (FRA) Produit Clé dynamométrique Couple et Angle (FRA) Année
(ESP) Tipo(s) (ESP) Producto Llave dinamométrica de par y ángulo (ESP) Año
(POR) Tipo (POR) Produto Chave dinamométrica torção e ângulo (POR) Ano
(ITA) Tipo TAWM912M (ITA) Prodotto Chiave dinamometrica coppia/angolo (ITA) Anno
(GER) Type(s) TAWM930M (GER) Produkt Drehwinkel-Drehmomentschlüssel (GER) Baujahr
(NED) Typen TAWM9135 (NED) Product Momentsleutel met hoekmeting (NED) Jaar
(POL) Typ TAWM14340 (POL) Produkt Klucz dynamometryczny kątowy (POL) Rok
(SWE) Typ TAWM24800 (SWE) Produkten Elektronisk Momentnyckel (SWE) År
TAW1412M
2018
(DEN) Typ (DEN) Produktet Elektronisk momentnøgle (DEN) År
(NOR) Typ TAW1430M (NOR) Produktet Momentnøkkel, moment og grader (NOR) År
(FIN) Tyyppi TAW38135 (FIN) Tuotteen Momenttiavain (FIN) Vuosi
(RUS) Тип TAW12340 (RUS) Изделие Электронный динамометрический ключ с функцией
предустановки угла затягивания (RUS) Год
(TUR) Tip TAW34800 (TUR) Ürün Elektronik Açılı Tork Anahtarı (TUR) Sene
(CZE) Typ (CZE) Výrobek Elektronický momentový klíč s úhlovým měřením (CZE) Rok
(SVK) Typ (SVK) Výrobok Elektronické momentové uhlové kľúče (SVK) Rok
(GRE) Τύπος: (GRE) Προιόν: Ηλεκτρονικό κλειδί ροπής και γωνίας (GRE) Χρόνος:

(ENG) Was manufactured in conformity with the provisions in the: (DEN) Produsert i samsvar med bestemmelsene i:
(FRA) A été fabriqué en conformité avec les dispositions des: (NOR) Produsert i samsvar med bestemmelsene i:
(ESP) Está fabricada según las disposiciones de: (FIN) On valmistettu noudattaen säännöksiä:
(POR) Foi fabricado em conformidade com os pressupostos: (RUS) Было произведено в соответствии с положениями:
(ITA) Prodotto in conformità con le disposizioni: (TUR) Aşağıdaki Standartlara uygun üretilmiştir:
(GER) In Übereinstimmung mit den Bestimmungen der: (CZE) Byl vyroben ve shodě s předpisy:
(NED) Is vervaardigd in overeenstemming met de bepalingen in de: (SVK) Bol vyrobený v zhode s predpismi:
(POL) Został wyprodukowany zgodnie z przepisami: (GRE) Κατασκευάστηκε σύμφωνα με τις διατάξεις του:
(SWE) Producerats enligt bestämmelserna i följande direktiv:
2004/108/EC
EN 61326-1:2006, EN 55011:2006, EN 61000-4-2, EN 61000-4-3, EN 61000-4-8
(ENG) Person authorized to compile the technical file (TCF):
(FRA) Personne autorisée à constituer le dossier technique:
(SPA) Persona facultada para elaborar el expediente técnico:
(POR) Pessoa autorizada para elaborar o dossier técnico:
(ITA) Persona autorizzata a compilare la pratica tecnica
(GER) Bevollmächtigte(r) zum Zusammenstellen technischer Unterlagen:
(NLD) Persoon die is gemachtigd het technisch dossier samen te stellen
(POL) Osoba odpowiedzialna za zestawianie pliku technicznego Sergio
(SWE) Person som är behörig att sammanställa den tekniska dokumentationen: Calvo
(DAN) Person bemyndiget til at udarbejde tekniske beskrivelser:
(NOR) Autorisert person for utarbeidelse av den tekniske filen:
(FIN) Henkilö on valtuutettu kokoamaan teknisen tiedoston
(TUR) Teknik dosyayı düzenlemeye yetkili kişi:
(RUS) Лицо, уполномоченное на составление технической документации:
(CZE) Autorizovaná osoba pro sestavení technického spisu:
(SLO) Osoba zodpovedná za vypracovanie technickej dokumentácie: Antigua ctra. Altube Km 5,5 - 01196 Arangiz, SPAIN
(GRE) Άτομο εξουσιοδοτημένο να καταρτίσει τον τεχνικό φάκελο

SNA EUROPE – 16 Allé Rosa Luxemburg, Eragny-sur-Oise, 95610 Cergy Pontoise Cedex, France – Phone: +33 1 39099868 – Fax : +33 1 39099881
20-2103-BA REV-1