TRIBHUWAN UNIVERSITY

INSTITUTE OF ENGINEERING
NATIONAL COLLEGE OF ENGINEERING

A
PROJECT PROPOSAL
ON
“TITLE OF THE PROJECT”

SUBMITTED BY:
NAME OF STUDENT (NCE076BCT001)
NAME OF STUDENT (NCE076BCT002)
NAME OF STUDENT (NCE076BCT003)
NAME OF STUDENT (NCE076BCT004)

SUBMITTED TO:
DEPARTMENT OF ELECTRONICS AND COMPUTER ENGINEERING

LALITPUR, NEPAL
MAY, 2024
ACKNOWLEDGEMENTS

On this page, the author expresses his gratitude and concern by using praising and
thanksgiving words.

ii
TABLE OF CONTENTS
Acknowledgements.............................................................................................................ii

List of Figures.....................................................................................................................iv

List of Tables.......................................................................................................................v

List of Abbreviations..........................................................................................................vi

1. Introduction..................................................................................................................1

1.1 Background................................................................................................................1

1.2 Problem statements....................................................................................................1

1.3 Objectives..................................................................................................................1

1.4 Scope..........................................................................................................................1

2. Literature Review........................................................................................................2

2.1 Related Work.............................................................................................................2

2.2 Related Theory...........................................................................................................2

3. Purposed Methodology................................................................................................3

4. Time Schedule.............................................................................................................5

5. Expected Output..........................................................................................................6

References............................................................................................................................7

iii
LIST OF FIGURES

Figure 1: Block diagram of proposed system......................................................................4

Figure 2: Gantt Chart...........................................................................................................5

iv
LIST OF TABLES

Table 1: Sample Table.........................................................................................................3

v
LIST OF ABBREVIATIONS

LAH List of Abbreviations Here

AMC Add More Contents

vi
1. INTRODUCTION

This chapter should contain brief background information and an overview of the project,
the problem statement, scope & objective of the project. It rarely contains drawings and
graphical illustrations.

1.1. Background

// Write down background information of the project and introduce the measure
functionalities and areas of the project. Citation required here.

//how did you decide to choose this project? write the motivation for this project.

1.2. Problem statements

// What is your main problem?

// What are the limitations of similar types of past projects?

1.3. Objectives

// List out the specific objectives to solve your problem. Do not write general objectives

 To <action verb> specific objective

1.4. Scope

// State the scope of the project and its limitations.

// Write down the applicable areas of your project.

1
2. LITERATURE REVIEW

This chapter should contain related work and related theory "basic theoretical
information" of the project. It evaluates the current work with the previous one. It depicts
the current implementations that overcome the previous problems and limitations of the
project and draws attention and focus on the foreknowledge work that would be
conducted based on the ongoing work at present. It must be clear and simple to
understand.

2.1. Related Work

// Case studies and surveys of previous works or systems can be included in this section.

write the Sentence written in your own words that is extracted by reading another
research paper/book/article/report [1].

2.2. Related Theory

Explain the theoretical background of the project.

2
n ( n−1 ) x
( 1+ x )n=1+ nx + +… (1)
1! 2!

2
3. PURPOSED METHODOLOGY

//This chapter should contain the methodology that will be implemented for problem-
solving. It should contain all the work done from feasibility study, requirement analysis,
data collection, and proposed system design to testing and implementation.

//This chapter should include all the diagrams that contribute to best graphically
representing the proposed system, its components & operations. They may be Context
models, Interaction models, Structural models, Behavioral models, Circuit diagrams,
Network diagrams, Model architecture, etc.

//use subheadings 3.1, 3.2 …

The methodology should describe how your project is carried out. So, required system
block diagrams or generic models along with system flowchart or program flowchart and
algorithm/pseudo code should be mentioned here.

Process modeling, data modeling, database design, forms, reports, and interface design
can be included in this chapter.

Similarly, if you have verified your project or system then write down the different
performance parameters you have chosen. For example, SNR, PSNR, ME, ROC,
accuracy, precision, etc.

3.1. Feasibility Study

\\Study and identify technical, economical, legal and others feasibility of your project.

3.2. Requirement Analysis

\\Determine the requirement of your project and prepare SRS document (if any)

3.3. Data Collection

\\ Mention the process of data preparation and source of data collection.

3
Table example

Table 1: Sample Table

Table1 Table2

3.4. Proposed System Design

Design an overall block diagram and control flow diagram to present your project idea in
a pictorial or diagrammatic format. Explain each figure clearly.

Figure 1: Block diagram of the proposed system

4
//explain every Figure 1 clearly.

3.5. Model Testing

\\ Mention Performance measure parameters of the proposed system or unit testing and
system testing based on the nature of your project.

3.6. If Any

\\ add other subheadings

3.7. If Any

5
4. TIME SCHEDULE

// project schedule
//Gantt chart example

Task\ Date 5/6 6/6 7/6 8/6 9/6 10/6 11/6 12/6 1/6 2/6

Literature Review and

Proposal

Collection of material/data

System Design

Simulation/Coding

Implementation

Final review

Documentation

Figure 2: Gantt Chart

6
5. EXPECTED OUTPUT

\\ what you expect as an output/result at the end of the project.

7
REFERENCES

[1] S. Burlakoti, "Weather Monitoring system," NCE journal of Science and

Engineering, vol. I, no. I, pp. 41-47, 2019.

//IEEE referencing format:

https://libraryguides.vu.edu.au/ieeereferencing/referencelist#s-lg-box-wrapper-9930149