Littelfuse TVS Diode TPSMA6L Datasheet PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

TVS Diodes

Surface Mount – 600W > TPSMA6L series

TPSMA6L Series RoHS Pb e3

Uni-directional Description

The TPSMA6L series is designed specifically to protect


sensitive electronic equipment from voltage transients
induced by load dump and other transient voltage
events, and it’s especially suitable for high reliability and
automotive application.

SMA low profile package (DO221-AC) has the same


electronical performance as the SMB package but with low
height profiles (1.1mm).

Agency Approvals
Features
AGENCY AGENCY FILE NUMBER
• Same power as standard clamping capability
E230531 SMB devices (600 W) • Fast response time:
• Hi reliability application typically less than 1.0ns
and automotive grade from 0 Volts to VBR min
Maximum Ratings and Thermal Characteristics AEC Q101 qualified • Built-in strain relief
(TA=25OC unless otherwise noted) • SMA low profile package: • Glass passivated junction
less than 1.1 mm • High temperature
Parameter Symbol Value Unit
• Footprint compatibility soldering: 260°C/10
Peak Pulse Power Dissipation at
TA=25ºC by 10x1000µs Waveform PPPM 600 W with standard SMA and seconds at terminals
(Fig.2)(Note 1), (Note 2) SMB products (easy to • Plastic package has
Power Dissipation on Infinite Heat
layout) underwriters laboratory
PM(AV) 3 W
Sink at TA=50OC • Typical failure mode is flammability V-0
Peak Forward Surge Current, 8.3ms short from over-specified • Typical maximum
IFSM 60 A voltage or current
Single Half Sine Wave (Note 3) temperature coefficient
Maximum Instantaneous Forward • Whisker test is conducted ΔVBR = 0.1% x VBR@25°C x ΔT
Voltage at 25A for Unidirectional VF 3.5V V based on JEDEC • Matte tin lead–free plated
Only JESD201A per its table 4a
• Halogen free and RoHS
Operating Junction and Storage
TJ , TSTG -65 to 150 °C and 4c
Temperature Range compliant
• IEC-61000-4-2 ESD
Typical Thermal Resistance Junction 15kV(Air), 8kV (Contact) • Pb-free E3 means 2nd
RuJL 35 °C/W
to Lead level interconnect is
• ESD protection of data
Typical Thermal Resistance Junction Pb-free and the terminal
RuJA 200 °C/W lines in accordance with
to Ambient finish material is tin(Sn)
IEC 61000-4-2
(IPC/JEDEC J-STD-
• EFT protection of data 609A.01)
Notes:
1. Non-repetitive current pulse, per Fig.4 and derated above TA=25ºC per Fig. 3. lines in accordance with
2. Mounted on 5.0x5.0mm copper pad to each terminal. IEC 61000-4-4
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional • Low inductance, excellent
device only.

Functional Diagram Applications


Bi-directional TVS devices are ideal for the protection of I/O Interfaces,
VCC bus and other vulnerable circuits used in Telecom,
Computer, Industrial and Consumer electronic applications.
Cathode Anode

Uni-directional

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16
TVS Diodes
Surface Mount – 600W > TPSMA6L series

Electrical Characteristics

Breakdown Test Maximum Maximum


Reverse Maximum Agency
Part Voltage VBR Current Clamping Reverse
Stand off Peak Pulse Approcal
Number Marking (Volts) @ IT Voltage VC Leakage IR
Voltage VR IT Current Ipp
(Uni) @ Ipp @ VR
(Volts) (mA) (A)
MIN MAX (V) (µA)
TPSMA6L5.0A AEA 5.0 6.40 7.00 10 9.2 65.3 800 X
TPSMA6L6.0A AGA 6.0 6.67 7.37 10 10.3 58.3 800 X
TPSMA6L6.5A AKA 6.5 7.22 7.98 10 11.2 53.6 500 X
TPSMA6L7.0A AMA 7.0 7.78 8.60 10 12.0 50.0 200 X
TPSMA6L7.5A APA 7.5 8.33 9.21 1 12.9 46.6 100 X
TPSMA6L8.0A ARA 8.0 8.89 9.83 1 13.6 44.2 50 X
TPSMA6L8.5A ATA 8.5 9.44 10.40 1 14.4 41.7 20 X
TPSMA6L9.0A AVA 9.0 10.00 11.10 1 15.4 39.0 10 X
TPSMA6L10A AXA 10.0 11.10 12.30 1 17.0 35.3 5 X
TPSMA6L11A AZA 11.0 12.20 13.50 1 18.2 33.0 1 X
TPSMA6L12A BEA 12.0 13.30 14.70 1 19.9 30.2 1 X
TPSMA6L13A BGA 13.0 14.40 15.90 1 21.5 28.0 1 X
TPSMA6L14A BKA 14.0 15.60 17.20 1 23.2 25.9 1 X
TPSMA6L15A BMA 15.0 16.70 18.50 1 24.4 24.6 1 X
TPSMA6L16A BPA 16.0 17.80 19.70 1 26.0 23.1 1 X
TPSMA6L17A BRA 17.0 18.90 20.90 1 27.6 21.8 1 X
TPSMA6L18A BTA 18.0 20.00 22.10 1 29.2 20.6 1 X
TPSMA6L20A BVA 20.0 22.20 24.50 1 32.4 18.6 1 X
TPSMA6L22A BXA 22.0 24.40 26.90 1 35.5 16.9 1 X
TPSMA6L24A BZA 24.0 26.70 29.50 1 38.9 15.5 1 X
TPSMA6L26A CEA 26.0 28.90 31.90 1 42.1 14.3 1 X
TPSMA6L28A CGA 28.0 31.10 34.40 1 45.4 13.3 1 X
TPSMA6L30A CKA 30.0 33.30 36.80 1 48.4 12.4 1 X
TPSMA6L33A CMA 33.0 36.70 40.60 1 53.3 11.3 1 X
TPSMA6L36A CPA 36.0 40.00 44.20 1 58.1 10.4 1 X
TPSMA6L40A CRA 40.0 44.40 49.10 1 64.5 9.3 1 X
TPSMA6L43A CTA 43.0 47.80 52.80 1 69.4 8.7 1 X
TPSMA6L45A CVA 45.0 50.00 55.30 1 72.7 8.3 1 X
TPSMA6L48A CXA 48.0 53.30 58.90 1 77.4 7.8 1 X
TPSMA6L51A CZA 51.0 56.70 62.70 1 82.4 7.3 1 X
TPSMA6L54A REA 54.0 60.00 66.30 1 87.1 6.9 1 X
TPSMA6L58A RGA 58.0 64.40 71.20 1 93.6 6.5 1 X
TPSMA6L60A RKA 60.0 66.70 73.70 1 96.8 6.2 1 X
TPSMA6L64A RMA 64.0 71.10 78.60 1 103.0 5.9 1 X
TPSMA6L70A RPA 70.0 77.80 86.00 1 113.0 5.3 1 X
TPSMA6L75A RRA 75.0 83.30 92.10 1 121.0 5.0 1 X
TPSMA6L78A RTA 78.0 86.70 95.80 1 126.0 4.8 1 X
TPSMA6L85A RVA 85.0 94.40 104.00 1 137.0 4.4 1 X

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16
TVS Diodes
Surface Mount – 600W > TPSMA6L series

I-V Curve Characteristics

Uni-directional

Vc VBR VR
V
IR VF
IT

Ipp

PPPM Peak Pulse Power Dissipation -- Max power dissipation


VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
VBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional

Ratings and Characteristic Curves (T =25°C unless otherwise noted)


A

Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve

100
Voltage Transients
PPPM-Peak Pulse Power (kW)

Voltage Across TVS


10
Voltage or Current

Current Through TVS

0.2x0.2" (5.0x5.0mm)
Copper Pad Area
0.1
Time
0.001 0.01 0.1 1
td-Pulse Width (ms.)
continues on next page.

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16
TVS Diodes
Surface Mount – 600W > TPSMA6L series

Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A

Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform

100 150
Peak Pulse Power (PPP) or Current (IPP)

tr=10µsec TJ=25°C

IPPM- Peak Pulse Current, % IRSM


Pulse Width(td) is defined
80 as the point where the peak
Derating in Percentage %

current decays to 50% of IPPM


Peak Value
100 IPPM
60
Half Value

40 ( )
IPPM IPPM
2

50 10/1000µsec. Waveform
as defined by R.E.A
20

td
0
0
0 25 50 75 100 125 150 175 0 1.0 2.0 3.0 4.0
TJ - Initial Junction Temperature (ºC) t-Time (ms)

Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Dissipation Derating
Curve

3.6
PM(AV), Steady State Power Dissipation (W)

10000
RuJA=RuJL
3.0

1000 Uni-directional V=0V


2.4
Uni-directional @VR
Cj (pF)

100
1.8

1.2
10
Tj=25ºC
RuJA=200°C/W
f=1.0MHz
0.6
Vsig=50mVp-p
1
1.0 10.0 100.0 1000.0 0
0 25 50 75 100 125 150 175
VBR - Reverse Breakdown Voltage (V)
TA - Ambient Temperature (ºC)

bargaining

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16
TVS Diodes
Surface Mount – 600W > TPSMA6L series

Soldering Parameters

Reflow Condition Lead–free assembly TP


tp

Ramp-up Critical Zone


- Temperature Min (Ts(min)) 150°C TL to TP
TL tL
Pre Heat - Temperature Max (Ts(max)) 200°C

Temperature (T)
Ts(max)
- Time (min to max) (ts) 60 – 180 secs
Ramp-down
Average ramp up rate (Liquidus Temp Ts(min)
3°C/second max ts
(TL) to peak Preheat

TS(max) to TL - Ramp-up Rate 3°C/second max


25˚C
- Temperature (TL) (Liquidus) 217°C t 25˚C to Peak
Reflow Time (t)
- Time (min to max) (ts) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
20 – 40 seconds Environmental Specifications
Temperature (tp)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max. High Temp. Storage JESD22-A103
Do not exceed 260°C
HTRB JESD22-A108

Physical Specifications
Temperature Cycling JESD22-A104

Weight 0.002 ounce, 0.061 gram MSL JEDEC-J-STD-020, Level 1


JEDEC DO-221AC Molded Plastic over glass
Case
passivated junction H3TRB JESD22-A101

Polarity Color band denotes cathode except Bipolar RSH JESD22-A111

Matte Tin-plated leads, Solderable per


Terminal
JESD22-B102D

Dimensions
Cathode Band

Inches Millimeters
C Dimensions
Min Max Min Max
A 0.156 0.181 3.950 4.600
A
B B 0.189 0.220 4.800 5.600
C 0.049 0.069 1.250 1.750
G D 0.088 0.116 2.250 2.950
F
E E E 0.030 0.059 0.750 1.500
D
F 0.005 0.010 0.125 0.250
G 0.035 0.043 0.900 1.100
3.12 (0.123) 1 .20 (0.047)

1.52 (0.060)

Mounting Pad Layout

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16
TVS Diodes
Surface Mount – 600W > TPSMA6L series

Part Numbering System Part Marking System

TPSMA6L xx A

Cathode Band

F
5% VBR VOLTAGE TOLERANCE Littelfuse Logo

XXX
VR VOLTAGE
SERIES Marking Code
YMXXX
Trace Code Marking
Y:Year Code
M: Month Code
XXX: Lot Code

Packaging

Component Packaging Packaging


Part number Quantity
Package Option Specification

TPSMA6LxxA DO-221AC 3000 Tape & Reel – 12mm/7” tape EIA RS-481

Tape and Reel Specification

0.157
(4.0)

0.47 Cathode
(12.0)

0.157 0.059 DIA Cover tape


(4.0) (1.5)

7.0 (178)
Dimensions are in inches
0.80 (20.2) (and millimeters).
Arbor Hole Dia.

Direction of Feed
0.49
(12.5)

© 2016 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/10/16

You might also like