INTERNATIONAL ISO

STANDARD 702-4

First edition
2004-05-15

Machine tools — Connecting dimensions

of spindle noses and work holding
chucks —
Part 4:
Cylindrical connection
iTeh STANDARD PREVIEW
Machines-outils — Dimensions d'assemblage de nez de broches et
(standards.iteh.ai)
mandrins porte-pièces —
Partie 4: Assemblage cylindrique
ISO 702-4:2004
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
662214cc4e93/iso-702-4-2004

Reference number
ISO 702-4:2004(E)

© ISO 2004
ISO 702-4:2004(E)

PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 702-4:2004
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
662214cc4e93/iso-702-4-2004

© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

 ISO 702-4:2004(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 702-4 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 8, Work
holding spindles and chucks.
iTeh STANDARD PREVIEW
ISO 702 consists of the following parts, under the general title Machine tools — Connecting dimensions of
spindle noses and work holding chucks:
(standards.iteh.ai)
 Part 1: Conical connection
ISO 702-4:2004
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
 Part 2: Camlock type
662214cc4e93/iso-702-4-2004
 Part 3: Bayonet type

 Part 4: Cylindrical connection

© ISO 2004 – All rights reserved iii

 iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 702-4:2004
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
662214cc4e93/iso-702-4-2004
INTERNATIONAL STANDARD ISO 702-4:2004(E)

Machine tools — Connecting dimensions of spindle noses and

work holding chucks —
Part 4:
Cylindrical connection

1 Scope
This part of ISO 702 specifies the sizes for interchangeability of cylindrical spindle noses and corresponding
connecting faces of face plates or work holding chucks.

NOTE The conical connection, “Camlock” and “bayonet” types are dealt with ISO 702-1, ISO 702-2 and ISO 702-3,
respectively.

iTeh STANDARD PREVIEW

2 (standards.iteh.ai)
Sizes for interchangeability

2.1 Spindle nose ISO 702-4:2004

https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
Only one bolt circle of diameter d2 is considered in this part of ISO 702, with 6 holes for No. 3 and 12 holes for
662214cc4e93/iso-702-4-2004
Nos. 4 to 28.

The dimensions are shown in Figure 1 and given in Table 1.

© ISO 2004 – All rights reserved 1

ISO 702-4:2004(E)

No. 3 Nos 4 to 28

Figure 1 — Spindle nose

iTeh STANDARD PREVIEW
(standards.iteh.ai)
Table 1 — Dimensions of spindle nose
ISO 702-4:2004
Dimensions in millimetres
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
662214cc4e93/iso-702-4-2004
Size No.
Dimension
3 4 5 6 8 11 15 20 28

nom. 90 115 140 170 220 300 380 520 720

d1
0 0 0 0 0 0 0 0 0
tol.
− 0,010 − 0,010 − 0,012 − 0,012 − 0,014 − 0,016 − 0,018 − 0,022 − 0,025

d2 70,6 82,6 104,8 133,4 171,4 235 330,2 463,6 647,6

d3 M10 M10 M10 M12 M16 M20 M24 M24 M30
f 16 20 22 25 28 35 42 48 56
k 14 17 19 22 25 32 37 42 50
w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3

2.2 Connecting faces

The connecting face dimensions of the chuck or face plate corresponding to the spindle noses specified in 2.1
are shown in Figure 2 and given in Table 2.

The number of holes depends upon the manufacturer's design; their pitch shall be a multiple of 30° in any
combination to match the spindle holes.

2 © ISO 2004 – All rights reserved

 ISO 702-4:2004(E)

No. 3 Nos 4 to 28

iTeh STANDARD PREVIEW

Figure 2 — Face plate

(standards.iteh.ai)
Table 2 —ISO
Connecting
702-4:2004 face dimensions
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab- Dimensions in millimetres
662214cc4e93/iso-702-4-2004
Size No
Dimension
3 4 5 6 8 11 15 20 28

nom. 90 115 140 170 220 300 380 520 720

d1
+ 0,022 + 0,022 + 0,025 + 0,025 + 0,029 + 0,032 + 0,036 + 0,044 + 0,050
tol.
0 0 0 0 0 0 0 0 0

d2 70,6 82,6 104,8 133,4 171,4 235 330,2 463,6 647,6

d3 12 12 12 14 18 22 26 26 33
gmin 4 4 5 5 5 5 5 5 5
w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3

3 Designation of cylindrical connections

A cylindrical connection in accordance with this part of ISO 702 is designated by

a) the number of this part of ISO 702; i.e. ISO 702-4;

b) the nominal size of the cylindrical connection.

EXAMPLE A connecting face of size No. 8 is designated as follows:

ISO 702-4 - No. 8

© ISO 2004 – All rights reserved 3

ISO 702-4:2004(E)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 702-4:2004
https://standards.iteh.ai/catalog/standards/sist/8917c696-c174-441e-b7ab-
662214cc4e93/iso-702-4-2004

ICS 25.060.20
Price based on 3 pages

© ISO 2004 – All rights reserved