Styrolution TDS300600621530

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Terluran ECO GP-22 MR50

Mechanical Post Consumer Recycling Acrylonitrile Butadiene Styrene (rABS)

DESCRIPTION
Terluran® ECO GP-22 MR50 is a mechanical post consumer recycling (PCR) grade, with a PCR content of 50% in a standard black color. It
combines easy-flow, high impact resistance and heat distortion with high quality surface finish; intended for a wide range of applications and
visible parts.

FEATURES APPLICATIONS
Medium flow Injection molding
Good impact resistance Appliance housings
Good heat distortion resistance Household and electronics appliances
High quality surface finish and gloss Visible parts
Great mechanical strength and rigidity
Standard black or dark grey color

Property, Test Condition Standard Unit Values

Rheological Properties

Melt Volume Rate 220 °C/10 kg ISO 1133 cm³/10 min 19

Mechanical Properties

Charpy Notched Impact Strength, 23° C ISO 179/1eA kJ/m² 18

Charpy Notched Impact Strength, -30 °C ISO 179/1eA kJ/m² 7

Tensile Stress at Yield, 23 °C ISO 527 MPa 35

Tensile Strain at Yield, 23 °C ISO 527 % 2.6

Tensile Stress at Break, 23 °C ISO 527 MPa 25

Tensile Strain at Break, 23 °C ISO 527 % 8

Tensile Modulus ISO 527 MPa 2100

Thermal Properties

Vicat Softening Temperature VST/B/50 (50N, 50 °C/h) ISO 306 °C 95

Other Properties

Density ISO 1183 kg/m³ 1040

Processing

Linear Mold Shrinkage ISO 294-4 % 0.4 - 0.7

Contact us:
Phone +1 866 890 6353
[email protected] Page 1 of 2
www.ineos-styrolution.com Revision Date: 01/30/2023
Terluran ECO GP-22 MR50
Mechanical Post Consumer Recycling Acrylonitrile Butadiene Styrene (rABS)

Property, Test Condition Standard Unit Values

Melt Temperature Range ISO 294 °C 220 - 260

Mold Temperature Range ISO 294 °C 30 - 80

Drying Temperature - °C 80

Drying Time - h 2-4

SUPPLY FORM
Terluran® ECO is delivered as spherical pellets. The bulk density of the pellets is from 0.55 to 0.65 g/cm³. Standard Packaging unit: 25 kg
PE-bag on palette, shrunk or wrapped with PE film or delivery in silo trucks. PE bags should not be stored outside. In dry areas with normal
temperature control, Terluran ECO pellets can be stored for relatively long periods of time without any change in mechanical properties.
Under poor storage conditions, Terluran ECO absorbs moisture, but this can be removed by drying.

PRODUCT SAFETY
No adverse effects on the health of processing personnel have been observed if the products are correctly processed and the production
areas are suitably ventilated. For styrene, acrylonitrile and 1,3-butadiene the maximum allowable workplace concentrations must be
observed according to the pertaining national regulations. In Germany, the following limit values are valid (Oct. 2002): styrene, MAK-value:
20 ml/m³ = 86 mg/m³; acrylonitrile, TRK-value: 3 ml/m³ = 7 mg/m³ and 1,3-butadiene, TRK-value: 5 ml/m³ = 11 mg/m³. According to EU
directive 67/548/EWG, Annex I and TRGS 905 (Oct. 2002), acrylonitrile and 1,3-butadiene are classified as carcinogenic, category 2
(´substances which should be regarded as if they are carcinogenic to man´) and 1 (substances known to be carcinogenic to man),
respectively. Experience has shown that during appropriate processing of Terluran ECO with suitable ventilation the values obtained are well
below the limits mentioned above. TRGS 402 (Germany) can be used for determining and assessing the concentrations of hazardous
substances in the air within working areas. Inhalation of gaseous degradation products, such as those which may arise on severe
overheating of the material or during pumped evacuation, must be avoided. Further information can be found in our Terluran ECO safety data
sheets.

DISCLAIMER
The above mentioned data are accurate to the best of our knowledge. They are based upon reputable labs and industry standard testing
methods. These are only typical values and actual product specification may deviate at industrial range. Therefore, no data in this technical
data sheet shall constitute a warranty or representation regarding product features, fitness of the product for a specific purpose or application
or its processability. INEOS Styrolution disclaims all liability in connection therewith. The customer himself is required to verify whether or not
the product is suitable for the further processing or application intended and whether or not the product complies with the relevant statutory
requirements. Unless explicitly and individually otherwise agreed in writing, INEOS Styrolution's sole and exclusive liability with respect to its
products is set forth in INEOS Styrolution's General Terms and Conditions for Sale.

Contact us:
Phone +1 866 890 6353
[email protected] Page 2 of 2
www.ineos-styrolution.com Revision Date: 01/30/2023

You might also like