Acrylic resin based multi-role curing, sealing and protective membrane for concrete
MATERIAL DESCRIPTION TYPIAL PROPERTIES*
MasterKure 181 is a non-degrading, membrane forming Properties listed are for guidance and are not a guarantee liquid based on acrylic resin suitable for spray application of performance. to freshly poured concrete. MasterKure 181 is available as a clear opaque liquid and white solar reflective version. Appearance Clear/Opaque liquid Specific gravity @25°C 0.810 – 0.858 Flashpoint 35°C (PMCC) The resultant film retains sufficient moisture in the Finished film appearance Clear or white, tack free, concrete to ensure full hydration of the cement, essential water repellent film for optimum strength development. The cured concrete is Water retention (ASTM Pass typically harder and exhibits a dust free surface with a C309) reduced incidence of drying shrinkage cracks. Drying time (ASTM 1 hour and 45 min at C309) 23°C
Additionally, the membrane acts as a primer system for
many subsequent surface finishes that do not rely on DIRECTIONS FOR USE penetration for substrate bond. When applied to floors, the The compound should be spray applied as evenly as MasterKure 181 seals and dustproofs the surface, possible on to the freshly placed concrete. eliminating the primary source of abrasion and enhancing durability. For horizontal surfaces MasterKure 181 should be applied as soon as the initial surface sheen has TYPICAL APPLICATIONS disappeared from the concrete surface. In the case of As a more effective and economical alternative to formed concrete, the product should be applied separate curing and priming/sealing regimes. Suitable for immediately on removal of the formwork. use on all concrete surfaces.
• Surfaces subject to finishing treatments.
SUBSEQUENT SURFACE FINISHES • Economical enhancement of concrete flatwork. The acrylic resin in MasterKure 181 ensure that bond is • In high-rise construction to eliminate the requirement maintained with adhesives used for installing tiles, and for water. other floor coverings. MasterKure 181 will act as a primer for paint systems and will enable most surface treatments ADVANTAGES to progress with minimal delay. Typical surface treatments • Eliminates the need for water. that will bond to surfaces with MasterKure 181 are: • Imparts a harder dust free surface • Does not support the growth of bacteria • Water based emulsion paints containing PVA, PVC or • Non degrading, acts as a primer system acrylic co-polymers. • Minimal delay for overcoating etc. • Tile adhesives based on the above polymers. • Abrasion resistant floors • Bituminous emulsions and solutions. • High curing efficiency • Thin section polymer modified cementitious systems. • Reduced labour costs • Polyurethane resin systems. • Reduces chloride penetration • Polysulphide systems. • Epoxy resin compositions which do not rely on PACKAGING penetration for substrate bond. MasterKure 181 is available in 210 litre drums. For further information regarding compatibility of STANDARDS MasterKure 181, contact Master Builders Solutions’ ASTM C309 Type 1 Class B and Type 2 Class B Technical Services Department.
March 21 Page 1 of 2 MasterKure 181 Acrylic resin based multi-role curing, sealing and protective membrane for concrete
SPECIFICATION CLAUSE HEALTH AND SAFETY
Where indicated, concrete shall be cured by application of As with all chemical products, care should be taken during MasterKure 181, curing compound based on acrylic resin use and storage to avoid contact with eyes, mouth, skin manufactured by Master Builders Solutions’ or similar and foodstuffs. Treat splashes to eyes and skin approved, to the following specification: immediately. If accidentally ingested, seek medical attention. Reseal containers after use. Use in well Specification type: ventilated areas and avoid inhalation. For further ASTM C309: Type 1 Class B information refer to the material safety data sheet. AASHTO M-148 NOTE MasterKure 181 is to be applied at a coverage rate of 6 Technical support, where provided, does not constitute to 8m² / L and strictly in accordance with the supervisory responsibility. For additional information manufacturer’s instructions. contact your local MB Construction Chemicals Solutions South Africa (Pty) Ltd representative. MB Construction COVERAGE AND YIELD Chemicals Solutions South Africa (Pty) Ltd shall not be The recommended rate of application is 6 to 8 m² / L. This liable for technical advice provided. corresponds to that at which MasterKure 181 has been tested, and at which it attains the claimed degree of curing MB Construction Chemicals Solutions South Africa (Pty) efficiency. In favourable conditions such as shaded Ltd reserves the right to have the true cause of any interior surfaces, adequate curing can be achieved with difficulty determined by accepted test methods. extended coverage rates. Undertaking such tests is not, and shall not be deemed to be, an admission of liability or an assumption of any risk, When using MasterKure 181 for floor areas where loss, damage or liability. maximum chemical and wear resistance is required, it is recommended that a further coat be applied after 24 QUALITY AND RESPONSIBLE CARE hours. All products originating from MB Construction Chemicals Solutions South Africa (Pty) Ltd are manufactured under STORAGE AND SHELF LIFE a management system independently certified to conform Store under cover, out of direct sunlight and protect from to the requirements of the quality standards ISO 9001, extremes of temperature. The shelf life is 12 months when environmental and occupational health and safety stored as above. Failure to comply with the recommended standards. storage conditions may result in premature deterioration of the product or packaging. For specific storage advice * Properties listed are based on laboratory-controlled consult Master Builders Solutions’ Technical Services tests. Department.
DISCLAIMER The technical information and application advice given in this MB Construction Chemicals Solutions South Africa (Pty) Ltd publication are based on the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user is responsible for checking the suitability of products for their intended use.
