SQ11 mini camera user manual in Spanish

04-14-2021 | Comments (2) | Tags: manual, manual-in-Spanish, mini-camera, camera-sq11,

Load attention! Before using it for the first time, fully charge the camera with the battery.

This small camcorder has a built-in lithium-ion battery. You can upload in one of the following
ways:

1. After stopping recording, connect the camcorder to the mini USB port of the PC.

2. Connect the compact camera to the mains charger 220 or portable charger 5B. In this case,
the miniature camera can still be used for the charging process. During the charging process,
the blue and red LEDs will continue to illuminate. When the mini camera battery is fully
charged, the blue LED indicator will light up and the red LED indicator light will go out.

If the built-in battery power is insufficient or the available memory card space is insufficient,
the blue and red LEDs on the mini camera will flash for 5 seconds at the same time, after which
the camera will save the recorded video and turn on. automatically turned off.

• If a memory card is inserted, the blue and red LEDs on the mini camcorder will flash
simultaneously for 5 seconds and then the mini camera will turn off automatically.

• If the camcorder is in standby mode and there is no operation mode, it will automatically
turn off after 1 minute to save internal battery.

Video recording

• Video resolution 1280x720P Press "On/Off" button to activate the micro camera (blue LED
indicator): the micro camera is in standby mode for 720p quality video recording. Press the
"on/off" button once to start recording the video. The blue LED flashes 3 times and exit. This
will be a 720p quality video recording. The video is automatically saved every 5 minutes. Press
the "On/Off" button to stop recording.

• Video resolution 1920x1080P Press the "On/Off" button to activate the mini camera; the
blue LED will light continuously. Press "Mode" once to switch to 1080p video recording mode;
The red and blue LEDs light up at the same time, and the mini camera has 1080P video
recording standby quality. So that the “On/Off” key once starts recording (blue LED turns off,
red LED flashes 3 times and exits), it will be 1080p quality video recording. The video is
automatically saved every 5 minutes. Press the "On/Off" button to stop recording.

• Motion Sensor Video Recording In the standby state of 720p or 1080p video recording, press
and hold the mini camera mode for 3 seconds; The camera will enter motion sensor recording
mode. When motion is detected, the video will start automatically and the red and blue LEDs
will flash simultaneously. Motion sensor video recordings are automatically saved every 5
minutes.

• Photos Press the "On/Off" button to activate the camera; the blue LED lights up. Double click
"Mode" to switch to shooting mode; the red LED will illuminate continuously. To take a photo,
press the "On/Off" button; The red LED indicator will flash once, which means the photo has
been saved. Photos received with permission-4032x3024.

•Night light Press the "On/Off" button to turn it on. Press and hold the “On/Off” key for 2
seconds; the red LED flashes twice; the night light is on. To deactivate the night lighting, press
and hold the “On/Off” key for 2 seconds, the red LED flashes three times, the night lighting
turns off.

• Power off To turn off the camera, press and hold the “On/Off” key for 6 seconds. If the
camcorder is in standby mode and not in use, it will automatically turn off after 1 minute.

• check the file Connect the camera to the computer, automatically define a few seconds as a
removable disk. The blue LED will indicate the information transmission process and the red
LED will indicate the internal battery charging process.

• Set the date and time Connect the camera to the computer. Setting the time is completed by
creating a text file called "TIMERSET.txt" in the root directory of the memory card, the content
of which is: "YYYYMMDDHHMMSS" "Y" (or "N" if you do not want it to be show the date and
time stamp on the video) For example, 20170625140003 Y After saving the file, disconnect the
camera from the computer and turn it on again.
SQ11 Operating Instructions
Burden

Attention! Before first use, fully charge the video camera battery!

This mini camcorder contains a built-in lithium-ion battery. You can upload one of the
following ways:

1. Connect the camcorder to the mini USB port of your PC, after stopping recording.

2. Connect the small camera to the 220 charger from a network or a 5B portable charger. In
this case, you can continue using the mini camera in the charging process. During charging, the
blue and red LEDs will light continuously.

After the mini camera battery is fully charged the blue LED will turn on and the red LED will
turn off.

• If the built-in battery is low, or free space on the memory card is not enough, the mini video
camera blue and red LED flashes at the same time for 5 seconds, after which the video camera
saves the video recorded and turns off automatically.

• If a memory card is inserted, the mini recorder's blue and red LED flashes at the same time
for 5 seconds, followed by the mini camera will turn off automatically.

• If the camcorder is in standby mode, and there is no operating mode, it automatically turns
off after 1 minute to save the internal battery.

Video recording
• 1280x720P Resolution Video Recording

Press the «On / Off» key to activate the mini camera - blue LED lights - a mini camcorder is in
standby mode recording the movie with 720p quality. Press the «On/Off» key once to start
recording a video - the blue LED will flash 3 times and exit - be a 720p quality video recording.
The video is automatically saved every 5 minutes. Press the “On/Off” button to stop recording.

• Resolution 1920x1080P Video recording

Press the «On/Off» key to activate the mini camera - Blue LED will light up constantly. Press
«Mode» once to switch to video recording mode with 1080p - Red and blue LED lights up at
the same time, the mini camera is in the expected video recording quality, 1080p. For the
«On/Off» key to start recording once - the blue LED turns off and the red LED flashes 3 times
and exit - it will be a 1080p quality video recording. The video is automatically saved every 5
minutes. Press the “On/Off” button to stop recording.

• Motion sensor video recording

In recording standby mode, 720p or 1080p video, press and hold the Mini Camcorder "Mode"
for 3 seconds - the camcorder will go into recording mode for the motion sensor. When
motion is detected the video will start automatically and the red and blue LED will flash
simultaneously. When motion sensor video recording is automatically saved every 5 minutes.

• Photo

Press the «On / Off» key to activate the camera - the blue LED lights up. Double click on
“Mode” to switch to shooting mode – red LED will light continuously. To take a photo, press
the «On/Off» button once - the red LED will flash once, the photo was saved. Permission
received photos - 4032x3024.

• Night lights

Press the “On/Off” key to turn it on. Press and hold the «On/Off» key for 2 seconds - the red
LED flashes twice - the night lights on. To deactivate the night lighting, press and hold the
«On / Off» key for 2 seconds, the red LED flashes three times - night lighting turns off.

• To turn off

To turn off the camcorder, press and hold the “On/Off” key for 6 seconds. If the camcorder is
in standby mode and not used, it automatically turns off after 1 minute.

• View files

Connect the camera to the computer - a few seconds it will automatically be defined as a
removable disk. The blue LED will indicate the information transfer process, and red - the
internal battery charging process.

• Set the date and time

Connect the video camera to the computer. Setting the time is done by creating a text file with
the name “TIMERSET.txt” in the root directory of the memory card, with the following content:

"YYYYMMDDHHMMSS" "Y" (or "N" if you don't want the date and time stamp displayed on the
video)

For example, 20170625140003 AND

After saving the file, disconnect the camcorder from the computer and turn it on again.

Characteristics:

● Video resolution: 1920x1080, 1280x720

● Frame rate: 15, 30 frames per second

● Video file type: AVI

● Photo resolution: 4032x3024

● Types of content Photo: JPEG

● Angle: 140°
● night light: 6 IR LEDS (range 5 meters, does not emit light!)

● Motion sensor: yes (5 meter range)

● Recording while charging +

● Operating time:

• 100 minutes (1 hour and 40 minutes) in continuous recording mode,

• About 5 hours in motion sensor mode

• Around the clock 24/7, when an external power source

● Memory card support: Micro SD up to 64GB

● Loop + recording

● Operating temperature: -10°C to +60°C

● Operating humidity: 15-85%

● Dimensions: 23x23x23 mm and 15 grams

Mini SQ11 camcorder with night lighting, a motion sensor and a 140° viewing angle

SQ11 is an improved version of the previous SQ8 and SQ9

SQ11 has built-in motion detector can take photos with a resolution of 4032x3024, and can
also be used for recording while charging 220V or charging portable devices, which increases
battery life by 30-40 times.