Engineering Drawing (EE-156)

NED University of Engineering and Technology Department of Electrical Engineering

NED University of Engineering & Technology

Department of Electrical Engineering

LAB MANUAL
For the course

ENGINEERING DRAWING
(EE-156) For F.E.(EE)

Instructor name:__________________________________
Student name:____________________________________
Roll no: Batch:___________________
Semester: Year:________________
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB MANUAL
For the course

ENGINEERING DRAWING
(EE-156) For F.E.(EE)

Content Revision Team:

Mr. Muhammad Uzair Khan and Mr. Muhammad Irfan Shaikh
Last Revision Date:

Approved By

The Board of Studies of Department of Electrical Engineering

__________________ ____________________

__________________ ____________________

__________________ ____________________
 Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

CONTENTS
Psychomotor / Cognitive / Affective Level: P3 / C3 / A4
CLO/PLO: CLO1 (C3)/ PLO1, CLO2 (P3)/ PLO5, CLO3 (A4), PLO6

S.No. Date Title of Experiment Total Marks Signature

To understand basic tools of AutoCAD 2015

1

To practice basic tools of AutoCAD through a

2 layout plan of a classroom
*
To draw civil layout plan of hotel on AutoCAD
3 with proper scaling and dimensions.
To understand the section views and Elevation
4 plans
*
To draw and understand sheet spacing and
5 location of orthographic views by Third Angle
Projection
*
To draw orthographic views of curved planes by
6 Third Angle Projection
*
To draw Isometric view of object using parallel
7 lines concept
To draw Isometric view of curved surfaces using
8 circle projections and layers concept

To convert and draw Isometric view into oblique

9 view
*
To understand and draw electrical wiring of
home.
10

*
Single Line Diagram
11

Extension board and its wiring diagram. (PBL)

12

*
RUBRIC based Assessment
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 01

Essential Overview of AutoCAD 2015

OBJECTIVE
To understand basic tools of AutoCAD 2015

Location: Computer Lab

Basic structure of AutoCAD 2015

AutoCAD is used to draw various types of drawings. Basic overview of AutoCAD 2015 is
shown in figure below.

Getting Start with AutoCAD

• Open AutoCAD 2015
• Type ‘mvsetup’ in command window
• Type ‘NO’ or ‘YES’ in ‘enable paper step
• Select type of drawing i.e ‘A’ for architecture drawing
• Select scale factor
• Enter width of paper
• Enter height of paper
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Overview of Basic Tools

• Draw
• Modify
• Dimensions
• Layers
• Units (directly enter)
• Text
• Block (like grouping)
• Hatch
• Snap and tracking

Exercise
1) Draw four rectangles one inside another by using different layers
2) Draw the following shapes with dimensions
• Circle (take your roll number as radius)
• Rectangle (large side is equal to your roll no)
• Triangle (each side is equal to your roll no)
• Pentagon (Each side is equal to your roll no)
• Ellipse (smaller radius is equal to your roll no)

Note
1. Download Free Education Version of AutoCAD 2015 or above from Auto desk website
2. Install AutoCAD 2015 on your Home PC as per instruction given in Lab.
2. Take handout of AutoCAD 2015 self-learning tutorial.
3. This tutorial will be helpful through the semester.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 02

Essential Practice of Basic Tools

OBJECTIVE
To practice basic tools of AutoCAD through a layout plan of a classroom

Location: Computer Lab

Lab Practice
Make layout plan of your classroom as per following dimensions
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
1. Practice of AutoCAD 2010
2. Use of following commands to draw this object
• Units
• Line
• Offset
• Circle
• Trim
• Dimension
• Text
• Plot
3. Understanding of floor plan
4. Representation of doors and windows

Exercise
Draw Layout plan of single room of your house.

Mention following information.

1. Dimensions
2. Door, windows and ventilator size
3. Size of Room

Note
Take print out of task and attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 03

Home Civil Layout Plan

OBJECTIVE
To draw civil layout plan of hotel on AutoCAD with proper scaling and dimensions.

Location: Computer Lab

Lab Practice
Make layout plan of a small hotel as per given dimensions.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Here
D1 = 3.5’ x 7’
D2 = 2.5’ x 7’
D3 = 5’ x 7’
W1= 3.5’ x 4’
V1 = 1’ x 1’

Learning Outcomes

1. Practice of AutoCAD 2015

2. Use following new commands to make above civil layout plan
• Arc
• Block
• Mirror
• Fillet
3. Understanding of Civil layout plans

Exercise
Draw Civil Layout plan of your house.
Mention following information.
1. Dimensions
2. Door, windows and ventilator size
3. Size of Room

Note
Take print out of task and attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 04

Section View and Elevation Plan

OBJECTIVE
To understand the section views and Elevation plans

Location: Computer Lab

Lab Practice
Draw the elevation plan of section A-A’ of civil layout plan.

Size of doors, windows and ventilators are same as mentioned in Lab session 3.

D1 = 3.5’ x 7’
D2 = 2.5’ x 7’
D3 = 5’ x 7’
W1= 3.5’ x 4’
V1 = 1’ x 1’

Height of area is 12’ while show 1.5’ base underground.

Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
1. Practice of AutoCAD 2015
2. Use following new commands to make above civil layout plan
• Layers to represent section line
• Hatch
3. Understanding of Section Views
4. Understanding of Elevation plans

Exercise
1. Make elevation plan of Section B-B’, C-C’ and D-D’
2. Make three random section lines on your house layout (one vertically and two
horizontally), and then make their elevation plan.

Mention following information.

i. Dimensions
ii. Hatch pattern and its marking

Note
Take print out of task and attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 05

Orthographic View

OBJECTIVE
To draw and understand sheet spacing and location of orthographic views by Third Angle
Projection

Location: Drawing Hall

Lab Practice
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
• Familiarity with Drawing hall and usage of drawing instrument
• Apply third angle projection
• Find horizontal spacing
• Find vertical spacing
• Divide your sheet
• Draw orthographic Views
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Exercise
Draw orthographic view of following object by Third Angle Projection with proper spacing
Note: Take the scale twice as given.

Note
• Use A3 drawing sheet
• Scale your drawing as per object size
• Attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 06

Orthographic Views
OBJECTIVE
To draw orthographic views of curved planes by Third Angle Projection

Location: Drawing Hall

Lab Practice
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
• Practice of orthographic view
• Understanding of hidden lines
• Understanding of curved surfaces from Isometric views
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Exercise
Draw orthographic view of following object by third Angle Projection.
(Take the scale twice as given)

Note
• Use A3 drawing sheet
• Scale your drawing as per object size
• Attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 07

Isometric View

OBJECTIVE
To draw Isometric view of object using parallel lines concept

Location: Drawing Hall

Lab Practice
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcome
• Practice of Isometric view with drawing instruments
• Practice of parallel lines using T-Square and Set-Square
• Understand and Practice of Dimensions on Drawing Sheet
Exercise
Draw Isometric View of following object
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Note
• Use A3 drawing sheet
• Scale your drawing as per object size
• Attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 08

Isometric View

OBJECTIVE
To draw Isometric view of curved surfaces using circle projections and layers concept

Location: Drawing Hall

Lab Practice
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
• Understanding and practice of projections using parallel layers Concept
• Practice of Isometric views on curved planes
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Exercise
Draw Isometric View of following object (Take the scale twice as given)

Note
• Use A3 drawing sheet
• Scale your drawing as per object size
• Attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 09

Sectional Views

OBJECTIVE
To draw Sectional Views of given Isometric Figure.

Location: Drawing Hall

Lab Practice
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes

• Understanding of Sectional Views of given Isometric view

• Practice of Full Section and Half Section Drawings

Exercise

Note
• Use A3 drawing sheet
• Scale your drawing as per object size
• Attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 10

Home Electrical Layout Plan

OBJECTIVE
To understand and draw electrical wiring of home

Location: Computer Lab

Lab Practice
Make electrical wiring diagram of following layout plan.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Size of doors, windows and ventilators are mentioned below,

D1 = 3.5’ x 7’
D2 = 2.5’ x 7’
W1 = 7’ x 4’
W2 = 4’ x 4’
V = 2’ x 2’

Learning Outcomes
• Understanding of electrical wiring
• Understanding lighting circuits and switching
• Understanding of power plans and sockets outlets

Exercise
Electrify the civil layout plan of your house.

Note
• Mention legends of electrical symbols used
• Take print out of task and attach it in your Engineering Drawing portfolio.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 11

Single Line Diagram

OBJECTIVE
To understand the purpose of Single Line Diagram

Location: Computer Lab

Theory

It is diagram that uses single lines and graphic symbols to indicate the path and components
of an electrical circuit.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

Learning Outcomes
• Understanding of electrical symbols used in Single line diagram
• Understanding of purpose of Single line Diagram
• Understanding of single line diagrams of industrial buildings and substations as
explained during Lab.
• Understanding of control diagrams and their operation

Exercise
Draw Single line diagram of your home from utility connection to final electrical load.
Engineering Drawing (EE-156)
NED University of Engineering and Technology Department of Electrical Engineering

LAB SESSION 12

Extension Board

Task 1: Prepare the extension board that

1. can run at least 10A load in total.
2. can run at least three loads at a time
3. must have current protection device
4. contain safety measures in order to prevent electrical hazards
Task 2: Sketch the wiring diagram of the above extension board.