Scribd
Upload
31 views3 pages

Hello World

Uploaded by

Abhishek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
31 views3 pages

Hello World

Uploaded by

Abhishek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include<lpc214x.

h>
#include<stdio.h>
//Function prototypes
void lcd_init(void);
void wr_cn(void);
void clr_disp(void);
void delay(unsigned int);
void lcd_com(void);
void wr_dn(void);
void lcd_data(void);
unsigned char temp1;
unsigned long int temp,r=0;
unsigned char *ptr,disp[] = "VARA",disp1[] = "MAHALAKSHMI";
int main()
{
IO0DIR = 0x000000FC; //configure o/p lines for lcd
IO0PIN = 0X00000000;
delay(3200); //delay
lcd_init(); //lcd intialisation
delay(3200); //delay
clr_disp(); //clear display
delay(3200); //delay
//........LCD DISPLAY TEST.........//
temp1 = 0x80; //Display starting address of
first line 1 th pos
lcd_com();
ptr = disp;
while(*ptr!='\0')
{
temp1 = *ptr;
lcd_data();
ptr ++;
}
temp1 = 0xC0; // Display starting address of second line 4 th
pos
lcd_com();
ptr = disp1;
while(*ptr!='\0')
{
temp1 = *ptr;
lcd_data();
ptr ++;
}
while(1);
} //end of main()

// lcd initialisation routine.


void lcd_init(void)
{
temp = 0x30;
wr_cn();
delay(3200);
temp = 0x30;
wr_cn();
delay(3200);
temp = 0x30;
wr_cn();
delay(3200);
temp = 0x20; // change to 4 bit mode from default 8 bit mode
wr_cn();
delay(3200);
// load command for lcd function setting with lcd in 4 bit mode,
// 2 line and 5x7 matrix display
temp = 0x28;
lcd_com();
delay(3200);
// load a command for display on, cursor on and blinking off
temp1 = 0x0C;
lcd_com();
delay(800);
// command for cursor increment after data dump
temp1 = 0x06;
lcd_com();
delay(800);
temp1 = 0x80; // set the cursor to beginning of line 1
lcd_com();
delay(800);
}
void lcd_com(void)
{
temp = temp1 & 0xf0;
wr_cn();
temp = temp1 & 0x0f;
temp = temp << 4;
wr_cn();
delay(500);
}
// command nibble o/p routine
void wr_cn(void) //write command reg
{
IO0CLR = 0x000000FC; // clear the port lines.
IO0SET = temp; // Assign the value to the
PORT lines
IO0CLR = 0x00000004; // clear bit RS = 0
IO0SET = 0x00000008; // E=1
delay(10);
IO0CLR = 0x00000008;
}
// data nibble o/p routine
void wr_dn(void) ////write data reg
{
IO0CLR = 0x000000FC; // clear the port lines.
IO0SET = temp; // Assign the value to the PORT lines
IO0SET = 0x00000004; // set bit RS = 1
IO0SET = 0x00000008; // E=1
delay(10);
IO0CLR = 0x00000008;
}
// data o/p routine which also outputs high nibble first
// and lower nibble next
void lcd_data(void)
{
temp = temp1 & 0xf0;
temp = temp ;//<< 6;
wr_dn();
temp= temp1 & 0x0f;
temp= temp << 4;
wr_dn();
delay(100);
}
void clr_disp(void)
{
// command to clear lcd display
temp1 = 0x01;
lcd_com();
delay(500);
}
void delay(unsigned int r1)
{
for(r=0;r<r1;r++);
}

You might also like