The Bottoms of My Pages Don

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 3

The bottoms of my pages

don't print
Article contributed by Suzanne S. Barnhill and Dave Rado

Frequently people have problems with material at the bottom of a page (the page number,
for example, or the footer) not printing correctly. Often, the characters get cut in half so that
only the top half of the line prints. The most common complaint is that the bottom of a page
border doesn’t print.
The most common cause of this problem is that the bottom margin, footer margin, or page
border is outside the printable area of the page. All printers have an irreducible unprintable
area necessitated by the mechanical requirements of paper handling.
Your printer manual may specify the printer’s printable area, or this information may be
included somewhere in the Properties dialog for the printer driver. The simplest way to
determine the printable area for your selected printer, however, is as follows:
1. Go to the Page Setup dialog and choose the Margins tab.
Note: Access this dialog in any version of Word by double-clicking the ruler.
Alternatively, use File | Page Setup in Word 2003 and earlier; in Word 2007, on the
Page Layout tab, locate the Page Setup group and click the dialog launcher in the
bottom right corner. On the Mac, you have to choose Microsoft Word from the Settings
drop-down before you will see the Margins button.
2. Set Top, Bottom, Left, and Right margins to zero. Click OK. Word will present the
following dialog box:

3. Accept Word’s offer to fix the margins and note what margins it sets. You can then
Cancel out of the Page Setup dialog without actually changing the margins, but this will
let you know what restrictions you’re working under.
Usually the unprintable area will be largest on the trailing edge, that is, the bottom of portrait
pages or one side of landscape pages. Inkjet printers in general have a larger unprintable
area at the bottom of the page than laser printers (up to 0.67" is not uncommon; the record
is probably 1.01" in case of the HP 420). Even printers that can print “borderless” may be
able to do so only on certain sizes of paper (with a special carrier) and/or will require a
special setting in the printer Properties.

Footer doesn’t print


Word’s default bottom margin is 1” (2.54 cm), which will be adequate for most printers, but
the page footer (if any) will be below the bottom margin. The default footer margin in Word is
0.5” (1.25 cm); this may well be too little for many printers. To deal with that, you need to
increase the footer margin. In Word 2002 and above, the header and footer margin settings
are on the Layout tab of the Page Setup dialog; in earlier versions, they are on the Margins
tab. Keep in mind that, if you increase the footer margin, you may also need to increase the
bottom margin to maintain the same amount of space between them.
Note: All versions of Word will warn you if you are about to print a document that has
page margins outside the printable area. Some earlier versions will not warn you if the
header or footer (or a page border) is outside the printable area. Print Preview, however,
should always give you a faithful representation of what will print using the currently
selected printer. Do not confuse Print Preview with Print Layout view, which merely
shows you the page as you have laid it out, not what will actually print.

Page border doesn’t print


Page borders present unique problems because they are, by default, much closer to the
edge of the page than any of the margins. If you click Options… in the Page Border dialog,
you will see that the default page border setting is “From edge of page,” with a default
measurement of 24 points (one third of an inch) and a maximum of 31 points (less than half
an inch), so obviously many printers will be unable to print these elements.
To remedy this, change the setting to “From text” instead (again only up to 31 pts); you'll
need to uncheck “Surround footer.” Note that “From text” means from the document body
margins, not the actual text present.; you can get more space between the page border and
your text by using left and right paragraph indents to reduce the size of the text inside the
document margins.

Specific Mac problems


A common problem on the Macintosh is that you are formatting the document for a printer
that is different from the one you are actually sending the document to.
 Go to the File>Print menu.
 Make sure that the name of the printer shown there matches the name of the
printer you actually have connected!
Older Macs have a bad habit of setting the "Format For" setting to "Any Printer."
Some corporations standardize on a single printer driver for every computer in
the company, regardless of which model printer is actually connected in your
office.
In either case, the computer now has no idea where the edge of the paper in the
printer is.
 Correct the setting so that the name of the printer is correct.
 Word will now warn you if you attempt to print a document that contains anything
that is placed closer to the edge of the paper than the printer can place ink.
Printing in the unprintable area
If you are determined to print outside the printer's printable area, some workarounds have
been devised. One of the simplest is to temporarily tape an extension onto the bottom of the
page and set a Custom page size a little longer than the actual sheet, adjusting margins
accordingly. This requires some calculation and experimentation but reportedly does work if
you are stubborn enough to try it! Microsoft's suggestion is to define the page size as smaller
than the actual so that Word will be tricked into printing the page border, with a
measurement “From edge of page,” higher than the actual bottom of the page.
Another solution is to switch to a more modern printer. Many laser printers will print within
0.17” of the edge on all sides, and inkjet printers marketed as "photo printers" often boast of
“borderless” printing (known as "full bleed" printing in the trade).

You might also like