Single Supply Bridge

a Transducer Amplifier
AD22055
FEATURES FUNCTIONAL BLOCK DIAGRAM
Gain of 400. Alterable from 40 to 1000
Output Span 20 mV to (VS – 0.25) V +VS OFS FILT
1 Pole Low-Pass Filtering Available 6 7 3
Offset Capability AD22055
Differential Input Resistance 230 kV
IN+ 8
Drives 1 kV Load to +4 V Using VS = +5 V A1
Supply Voltage: +3 V to +36 V IN– 1 A2 5 OUT

Transient Spike Protection and RFI Filters Included

Peak Input Voltage (40 ms): 60 V
Reversed Supply Protection: –34 V 4 GAIN
Operating Temperature Range: –408C to +1258C
2
APPLICATIONS GND

Interface for Pressure Transducers, Position

Indicator, Strain Gages and Other Low Level Signal
Sources

GENERAL DESCRIPTION The extended temperature range allows for local signal condi-
The AD22055 accepts a differential signal from a bridge trans- tioning for oil and hydraulic pressure sensors as well as other
ducer whose common-mode signal can be anywhere between automotive sensors.
the power supplies. The use of an external gain resistor allows the user to compen-
sate transducer gain error and temperature drift.

+5 VOLT
VREF
OUTPUT

8 7 6 5
IN+ OFS +VS OUT
AD22055 GAIN = 400
IN– GND FILT GAIN
1 2 3 4

1kΩ
ANALOG
GROUND

Figure 1. Typical Application Circuit for a Pressure Sensor Interface

REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
which may result from its use. No license is granted by implication or Tel: 617/329-4700 World Wide Web Site: http://www.analog.com
otherwise under any patent or patent rights of Analog Devices. Fax: 617/326-8703 © Analog Devices, Inc., 1997
AD22055–SPECIFICATIONS (@ T = + 258C, V = +5 V, V A S CM = 0, unless otherwise noted)

Parameter Comments Test Conditions Min Typ Max Units

INPUTS (PINS 1 AND 8)
VCM Common-Mode Range 0 5 V
CMRRLF Common-Mode Rejection Ratio f ≤ 10 Hz –80 –90 dB
CMRRHF Common-Mode Rejection Ratio f = 10 kHz –60 –75 dB
RINCM Common-Mode Input Resistance Pin 1 or Pin 8 to Pin 2 180 230 kΩ
RMATCH Matching of Input Resistances ± 0.5 %
RINDIFF Differential Input Resistance Pin 1 to Pin 8 180 230 300 kΩ
PREAMPLIFIER
GCL Closed-Loop Gain1 40 V/V
VO Output Voltage Range (Pin 3) +0.02 +4.75 V
RO Output Resistance2 77.6 80 82.4 kΩ
OUTPUT BUFFER
GCL Closed-Loop Gain1 RLOAD ≥ 10 kΩ 9.95 10 10.05 V/V
VO Output Voltage Range +0.02 +4.75 V
RO Output Resistance (Pin 5) VO ≥ 0.1 V dc 2.0 Ω
OVERALL SYSTEM
GCL Gain1 VO ≥ 0.1 V dc 398 400 402 V/V
Gain Drift –40°C to +125°C –60 ppm/°C
Gain Drift –125°C to +150°C –500 ppm/°C
VOS Initial Offset Voltage3 –1 0.05 1 mV
Offset Drift –40°C to +125°C 1 µV/°C
Offset Drift –125°C to +150°C –10 µV/°C
Input Resistance Pin 7 to Pin 2 2.5 3.0 kΩ
IOSC Short-Circuit Output Current 7 11 25 mA
BW–3 dB –3 dB Bandwidth VO = + 1 V dc 20 30 kHz
SR Slew Rate 0.2 V/µs
NSD Noise Spectral Density3 f = 100 Hz to 10 kHz 0.2 µV/√Hz
POWER SUPPLY
VS Operating Range TA = TMIN to TMAX 3 5 36 V
IS Quiescent Supply Current4 200 500 µA
TEMPERATURE RANGE
TOP Operating Temperature Range –40 +125 °C
NOTES
1
A2 gain is trimmed to ± 0.5% with a 0.01% 1 kΩ resistor to ground from Pin 4. The overall gain is trimmed to a gain of 400 ± 0.5% with the same 1 kΩ resistor. The
gain of A1 (the ratio of overall gain to A2 gain) is used to adjust the overall gain and, therefore, is not trimmed explicitly to 40. Note that the actual gain to a particu-
lar application can be modified by the use of an external resistor at Pin 4.
2
The actual output resistance of A1 is only a few ohms, but access to this output, via Pin 3, is always through an 80 k Ω resistor, which is trimmed to ± 3%.
3
Referred to the input (Pins 1 and 8).
4
With VDM = 0 V. Differential mode signals are referred to as V DM, while VCM refers to common-mode voltages.
All min and max specifications are guaranteed, although only those marked in boldface are tested on all production units at final test.
Specifications subject to change without notice.

–2– REV. 0
 AD22055
ABSOLUTE MAXIMUM RATINGS 1 PRODUCT DESCRIPTION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . +3 V to +36 V The AD22055 is a single supply difference amplifier consisting
Peak Input Voltage (40 ms) . . . . . . . . . . . . . . . . . . . . . . . . 60 V of a precision balanced attenuator, a very low drift preamplifier
Reversed Continuous Supply Voltage . . . . . . . . . . . . . . –34 V and an output buffer amplifier (A1 and A2, respectively, in the
Operating Temperature . . . . . . . . . . . . . . . . –40°C to +125°C functional block diagram). It has been designed so that small
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C differential signals, VDM, can be accurately amplified and fil-
Output Short Circuit Duration . . . . . . . . . . . . . . . . Indefinite tered in the presence of large common-mode voltages, VCM,
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . +300°C without the use of any other active components.
1
Stresses above those listed under “Absolute Maximum Ratings” may cause The common-mode range resistors in this network are trimmed
permanent damage to the device. This is a stress rating only; the functional to match better than one part in 10,000. The resistive attenua-
operation of the device at these or any other conditions above those indicated in the
operation sections of this specification is not implied. Exposure to absolute
tor network is situated at the input to the AD22055 (Pins 1
maximum rating conditions for extended periods may affect device reliability. and 8) allowing the common-mode voltage at Pins 1 and 8 to be
two times greater than that which can be tolerated by the actual
ORDERING GUIDE input of A1. As a result, the input common-mode range extends
from ground to the power supply voltage.
Temperature Package Package Two small filter capacitors (not shown) have been included at
Model Range Description Option* the inputs to A1 to minimize the effects of any spurious RF sig-
nals present in the signal.
AD22055N Plastic DIP N-8
AD22055R –40°C to +125°C Plastic SOIC SO-8 Internal feedback around A1 sets the closed-loop gain of the
preamplifier to 40 V/V from the input pins, and the output of
*N = Plastic DIP; SO = Small Outline Package. A1 is connected to Pin 3 via a 80 kΩ resistor, which is trimmed
to ± 3% to facilitate the low-pass filtering of the signal. The out-
PIN CONNECTION put buffer A2 has a gain of 10 V/V (using a precise 1 kΩ resistor
from Pin 4 to ground) setting the precalibrated, overall gain of
IN– 1 8 IN+
the AD22055, to 400 V/V. This gain is easily user-configurable.
GND 2 AD22055 7 OFS Overall gain is programmed using the following equation:
TOP VIEW
FILT 3 (Not to Scale) 6 +VS
 9 kΩ 
Gain = 40  1 +
GAIN 4 5 OUT
 V/V (1)
 RGAIN 
The dynamic properties of the AD22055 are optimized for
interfacing to transducers, particularly those with a Wheatstone
PIN DESCRIPTION Bridge configuration. Its rejection of large, high frequency,
common-mode signals makes it superior to that of many alter-
8-Pin SOIC native approaches. This is due to the very careful design of
Pin Function the input attenuator and the integration of this highly balanced,
high impedance system with the preamplifier.
1 IN–
2 Ground
3 Filter
4 Gain
5 Out
6 +VS
7 OFS
8 IN+

CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. WARNING!
Although the AD22055 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
ESD SENSITIVE DEVICE
precautions are recommended to avoid performance degradation or loss of functionality.

REV. 0 –3–
AD22055
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).

8-Lead Plastic DIP

(N-8)

0.430 (10.92)

C2978–12–1/97
0.348 (8.84)

8 5
0.280 (7.11)
0.240 (6.10)
1 4 0.325 (8.25)
0.300 (7.62)
PIN 1 0.060 (1.52)
0.015 (0.38) 0.195 (4.95)
0.210 (5.33)
MAX 0.115 (2.93)
0.130
0.160 (4.06) (3.30)
0.115 (2.93) MIN
0.015 (0.381)
0.022 (0.558) 0.100 0.070 (1.77) SEATING
PLANE 0.008 (0.204)
0.014 (0.356) (2.54) 0.045 (1.15)
BSC

8-Lead Plastic SOIC Package

(SO-8)
0.1968 (5.00)
0.1890 (4.80)

8 5
0.1574 (4.00) 0.2440 (6.20)
0.1497 (3.80) 1 4 0.2284 (5.80)

PIN 1 0.0688 (1.75) 0.0196 (0.50)

x 45°
0.0098 (0.25) 0.0532 (1.35) 0.0099 (0.25)
0.0040 (0.10)

8°
0.0500 0.0192 (0.49) 0°
SEATING (1.27) 0.0138 (0.35) 0.0098 (0.25) 0.0500 (1.27)
PLANE BSC 0.0075 (0.19) 0.0160 (0.41)

PRINTED IN U.S.A.

–4– REV. 0