Scribd
Upload
23 views26 pages

Electronic Devices Lecture 15

Uploaded by

bodzzaa21
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
23 views26 pages

Electronic Devices Lecture 15

Uploaded by

bodzzaa21
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 26

Electronic Devices

Lecture 15
Bipolar Junction Transistor

Dr. Roaa Mubarak


AC Analysis of BJT
• AC analysis of BJT included the large signal and small signal.
• Here we deal with small signal ( large signal used power amplifiers).
• The analysis is complex so, we use a small signal model to replace the BJT.
• The total response = the dc response + the AC response.
• A model is an equivalent circuit that represents the AC characteristics of the
transistor.
• A model uses circuit elements that approximate the behavior of the transistor.
• There are two models commonly used in small signal AC analysis of a
transistor:
– re model
– Hybrid model
BJT Modeling
The ac equivalent of a transistor network is obtained by:
1- Setting all dc sources to zero and replacing them by a short-circuit equivalent
2- Replacing all capacitors by a short-circuit equivalent
3- Removing all elements bypassed by the short-circuit equivalents introduced by
steps 1 and 2
4- Redrawing the network in a more convenient and logical form
BJT small signal Modeling
5- replacing the BJT with appropriate model
– re transistor model
– Hybrid model
Hybrid model
• The hybrid 𝛑 model is most useful for analysis of high-frequency
transistor applications.

• At lower frequencies the hybrid 𝛑 model closely approximate the re


parameters, and can be replaced by them.
Hybrid 𝛑 model

Voltage Controlled Current Source “VCCS” Current Controlled Current Source “CCCS”

𝐼𝐶
𝑔𝑚 = 𝛃
𝑉𝑇
𝑉𝑇 𝑟𝛑 =
𝑟𝛑 = 𝑔𝑚
𝐼𝐵
Hybrid T model

𝐼𝐶
𝑔𝑚 =
𝑉𝑇
𝑉𝑇 𝛂
𝑟𝑒 = =
𝐼𝐸 𝑔𝑚

Current Controlled Current Source “CCCS”


Voltage Controlled Current Source “VCCS”
The steps for solving AC analysis of BJT
• First DC Analysis
Using the DC analysis to calculate the parameters of small signal model
𝑔𝑚 , 𝑟𝛑 𝑎𝑛𝑑 𝑟𝑒 .
• Second AC Analysis
1- Replace all the capacitors by short circuits, the inductors by open
circuits.
2-replace the voltage Dc source by short circuit, and replace the
current DC source by open circuit.
3- replace the BJT with one of small signal models.
4- Analyze the circuit to determine the amplifier gain.
BJT Configurations

Common Common Common


Emitter Base Collector
Example
Determine the gain of the following amplifier as 𝛃 = 100
Solution
1- Using the DC analysis to determine the Q point
Assuming Active mode
By KVL in input loop:
-3 +100𝐼𝐵 + 0.7 = 0
3−0.7
𝐼𝐵 = = 0.023mA
100
𝐼𝐶 = 𝛃𝐼𝐵 = 2.3mA
𝐼𝐸 = 𝐼𝐶 + 𝐼𝐵 = 2.323𝑚𝐴
𝑉𝑜 = 𝑉𝑐 = 𝑉𝑐𝑐 − 𝐼𝐶 𝑅𝑐 = 10 − (2.3)(3)=3.1V
𝑉𝑐 > 0.7 then our assumption is true Vc =Vo
+
-
0.7 V

3V
Solution
2- Determine the AC parameters.
𝐼𝐶 2.3𝑚𝐴
𝑔𝑚 = = = 88mA/v
𝑉𝑇 26𝑚𝑣
𝑉𝑇 26𝑚𝑣 𝑅𝐶
𝑟𝛑 = = =1.13kΩ
𝐼𝐵 0.023𝑚𝐴

3- Draw the circuit with AC model ( 𝛑 Model)


Note: short circuit the DC voltage source and
open circuit the DC current source
Solution
𝑅𝐶
4- Analyze the small signal equivalent circuit
𝑣𝑜 = -𝑔𝑚 𝑣𝑏𝑒 𝑅𝐶
𝑟𝛑 1.13
𝑣𝑏𝑒 = ( )𝑣𝑖 = ( )𝑣𝑖 =0.011𝑣𝑖
𝑅𝐵𝐵 +𝑟𝛑 101.13
𝑣𝑜 = -(88)(0.011) 𝑣𝑖 (3) = -2.94 𝑣𝑖
𝑣𝑜
𝐴𝑣 = = −2.94 = 2.94
𝑣𝑖
Early Effect

• The early effect is the variation in the width of the base in a bipolar transistor
due to a variation in the applied base-to-collector voltage, and this causes the
𝐼𝐶 depends not only on 𝐼𝐵 but also on 𝑉𝐶𝐸 .
Early Effect
Early effect can be assigned in the ac signal model as an output resistance to
the controlled source in the hybrid 𝛑 model.
Example2
• Ac equivalent circuit
Example2

𝑅𝐵 = 𝑅1 // 𝑅2 = 10 kΩ //30 kΩ =7.5KΩ

R = 𝑅𝐶 // 𝑅3 = 4.3 kΩ// 100 kΩ = 4.12KΩ


Example2

• 𝑅𝐿 = 𝑟𝑜 // 𝑅𝐶 // 𝑅3
Input Resistance
Output Resistance
Example3

𝑅𝐵 = 𝑅1 // 𝑅2 = 160kΩ //300 kΩ =104KΩ

𝑅𝐿 = 𝑅7 // 𝑅3 = 100kΩ// 22kΩ = 18KΩ


Example3

𝑅𝐵
𝑣𝑏 = 𝑣𝑖
𝑅𝐼 + 𝑅𝐵
Example3

𝛃
𝑟𝛑 =
𝑔𝑚
Example3
Example3
Example3

You might also like