EMRAX 228 Datasheet v1.5

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

228

EMRAX 228 is a compact axial flux permanent magnet synchronous electric motor with high power/torque density.
It offers the middle of the range performance and is a great fit for where high power output in a small package is needed. Contact u s to find out about its
typical applications!

EMRAX 228
DIAMETER | LENGTH 228 mm | 86 mm
WEIGHT 12,9-13,5 kg
COOLING air / water / combined
PEAK | CONTINUOUS POWER 124 kW | 75 kW*
PEAK | CONTINUOUS TORQUE 230 Nm | 130 Nm*
MAXIMUM SPEED 6500 RPM
OPERATING VOLTAGE 50 - 830 V
EFFICIENY up to 96%*
POSITION SENSOR resolver / encoder

*Subject to motor configuration, drive cycle, thermal conditions, and controller capability.

Version 1.5
EMRAX 228 EMRAX 228 EMRAX 228
High Voltage Medium Voltage Low Voltage

AC = Air cooled
LC = Liquid cooled AC LC CC AC LC CC AC LC CC
CC = Combined cooled (Air + liquid)

Ingress protection IP21 IP66 IP21 IP21 IP66 IP21 IP21 IP66 IP21

min. min. min.


ambient ambient ambient
6 l/min, 6 l/min, 6 l/min,
Cooling specifications air 20⁰C AC+LC* air 20⁰C AC+LC* air 20⁰C AC+LC*
max. max. max.
20 m/s 20 m/s 20 m/s
50°C 50°C 50°C

Maximum motor temperature [°C] 120

Motor connection type UVW or 2x UVW UVW or 2x UVW UVW or 2x UVW

Voltage required for peak power [VDC ]** 830 630 250

Motor peak efficiency [%] 96%

Peak power S2 2min [kW] 104 kW at 4500 RPM 124 kW at 5500 RPM 124 kW at 5500 RPM

Continuous power S1 (kW) 55 64 75 55 64 75 55 64 75

Peak torque [Nm] 220

Continuous torque [Nm] 96 112 130 96 112 130 96 112 130

Limiting speed [RPM] 6500

KV constant at no load [rpm/VDC] 10,14 15,53 40,30

KV constant at nominal load [rpm/VDC] 7,85 12,05 30,94

KV constant at peak load [rpm/VDC] 5,65 8,68 21,91

KT constant [Nm/ARMS] 0,94 0,61 0,24

Peak motor current [ARMS] 235 360 920

Continuous motor current [ARMS] 120 180 470

Internal phase resistance at 25 °C [mΩ]*** 15,48 7,06 1,35

LD induction of 1 phase [µH] 225,5 96,5 15,0

Induced voltage [VRMS/RPM] 0,07348 0,04793 0,01840

Magnetic flux – axial [VS] 0,05728 0,03737 0,01434

Temperature sensor on the stator windings KTY 81/210

Number of pole pairs 10

Winding configuration star

Rotor Inertia [kg*m²] 0,02521

Bearing configuration 6206 | 3206

Weight [kg] 12,9 13,5 13,2 12,9 13,5 13,2 12,9 13,5 13,2

*Combined cooled motor (CC) requires cooling specifications from air and liquid cooled motors, to reach its specifications. It cannot only be cooled as an air-cooled motor.
Every EMRAX motor requires sufficient air circulation. The motors should not be completely enclosed in any condition. Please check EMRAX motor manual to learn more.
Performance in your application will depend on your installation details and boundary conditions. Please contact us to learn more.
**All motors are tested for 833V maximum voltage.
***Measured Phase to Phase, then divided by 2.
HV option is operating at speeds lower than its limiting, due to 830 V voltage limitations.

All values given are for a standard 3 phase UVW version, please consult EMRAX on 2x UVW values. R1UVW=2*R2UVW

EMRAX d.o.o., Molkova pot 5, 1241 Kamnik, Slovenia, EU l [email protected] l +386 82053853 l www.emrax.com

You might also like