CYLINDER SERIES “ISO 15552”

SERIES 3 Ø 32÷125 mm

Cylinders made to ISO 15552 available in various versions

and with a wide range of accessories:
• Configuration with or without magnet
• Single- or double-acting – single- or through-rod
• Wide choice of NBR, POLYURETHANE and FKM/FPM
gaskets (for high temperatures)
• Special versions on request
• Fixing accessories, guide units and mechanical piston
rod lock.
The shape of series 3 cylinder liners is designed to reduce
weight to a minimum.
Two T slots, on the same side as the threaded ports, to
allow the insertion of retracting sensors.
The other three sides of the liner are smooth, with no
grooving, to make them easier to clean.

TECHNICAL DATA Polyurethane NBR FKM/FPM Low Temperature

Operating pressure max 10 bar (max 1 MPa - 145 psi)
Temperature range –20°C to +80°C (non-magnetic cyl.) –10°C to +80°C (non-magnetic cyl.) –10°C to +150° (non-magnetic cyl.) –35°C to + 80°C
–20°C to +70°C (magnetic cyl.) –10°C to +70°C (magnetic cyl.)
Fluid Unlubricated air. Lubrication, if used, must be continuous
Bore Ø 32 ; Ø 40 ; Ø 50 ; Ø 63 ; Ø 80 ; Ø 100 ; Ø 125
Design Heads with Tap Tite screws
Standard stroke Single-acting: for bores Ø 32-63, strokes 1-250 mm
Double-acting: for bores Ø 32-80, strokes 1-2800 mm
for bores Ø 100-125, strokes 1-2600 mm
Versions Double-acting cushioned, Single-acting retracted piston rod cushioned, Through-rod cushioned,
High-temperature, Piston rod lock, Oil seal, Through-rod oil seal, Non-stick-slip*.
Sensor magnet All versions come complete with magnet. Supplied without magnet on request.
Inrush pressure Ø 32; 40: 0.4 bar
Ø 50;63 strokes < 1500 mm: 0.3 bar; strokes 艌 1500 mm: 0.4 bar
Ø 80;100; 125 strokes < 1500 mm: 0.2 bar; strokes 艌 1500 mm: 0.4 bar
Note on use *Using for speeds lower than 0.2m/s, to prevent surging.
For no-stick-slip versions use no-lubricated air only
Forces generated at 6 bar thrust/retraction See GENERAL TECHNICAL DATA PAGE 16
Weights See GENERAL TECHNICAL DATA PAGE 16

COMPONENTS

 PISTON ROD: C45 steel or stainless steel, thick

chromed
 HEAD: die cast aluminium
 PISTON ROD GASKET: polyurethane, NBR or
FKM/FPM 1 3 4 2 10 5 6 8 7 9 11 12
 GUIDE BUSHING: steel strip with bronze and
PTFE insert
 BARREL: drawn anodised calibrated aluminium
 HALF-PISTON: self-lubricating technopolymer with
built-in cushioning olives (aluminium with PTFE
pad for diameters 80-100-125)
 PISTON GASKET: polyurethane, NBR or FKM/FPM
MAGNET: plastoferrite
BUFFER + Static O-rings: NBR or FKM/FPM
CUSHIONING GASKET: polyurethane, NBR or
FKM/FPM
CUSHIONING NEEDLE: OT 58 with needle out
movement safety system even when fully open
SCREWS: Tap Tite for assembly

1
DIMENSIONS OF STANDARD VERSION

L+
F WH L0+ VA
C1 BG
CH3 RT VD N

Q
TG

B1

KK
D
B

B
E

P
121
TG CH2 CH1 A EE
124 E PL PL

126
+ = ADD THE STROKE

DIMENSIONS OF THROUGH-ROD VERSION

ZM++
WH+ L0+ WH F
BG C1
N VD CH3 RT
Q

TG
B1
KK
D

E
P

A EE CH1 CH2 TG
PL PL E

122
+ = ADD THE STROKE
++= ADD TWICE THE STROKE

Ø PL VD A B B1 WH C1 CH1 CH2 CH3 KK D TG VA F EE RT E L L0 ZM BG N P Q

32 10 6.5 10 30 28 26 16 10 17 6 M10x1.25 12 32.5 4 22 G1/8 M6 46 120 94 146 14.5 4.5 6 4
40 12 8 10 35 33 30 20 13 19 6 M12x1.25 16 38 4 24 G1/4 M6 54 135 105 165 14.5 4.5 6 4
50 14 13 10 40 38 37 25 17 24 8 M16x1.5 20 46.5 4 32 G1/4 M8 64.5 143 106 180 17.5 5.5 6 6
63 16 14 10 45 40 37 25 17 24 8 M16x1.5 20 56.5 4 32 G3/8 M8 75.5 158 121 195 17.5 5.5 6 6
80 18 12 12 45 43 46 33 22 30 10 M20x1.5 25 72 4 40 G3/8 M10 94 174 128 220 21.5 5.5 10 7
100 20 14 12 55 49 51 38 22 30 10 M20x1.5 25 89 4 40 G1/2 M10 111 189 138 240 21.5 5.5 10 7
125 25 20 10 60 54 65 45 27 41 12 M27x2 32 110 6 54 G1/2 M12 135 225 160 290 25.5 6.5 12 8

VERSION 126 (SINGLE-ACTING)

Upper limit Stroke Lower limit L0- Ø 32 L0 - Ø 40 L0 - Ø 50 L0 - Ø 63 L - Ø 32 L - Ø 40 L - Ø 50 L - Ø 63
ISO 0 <C≤ 25 94 105 106 121 120 135 143 158
ISO 25 <C≤ 50 94 105 106 121 120 135 143 158
NON ISO 50 <C≤ 75 115 129.5 130.5 145.5 141 159.5 167.5 182.5
NON ISO 75 <C≤ 100 136 154 155 170 162 184 192 207
NON ISO 100 <C≤ 125 157 178.5 179.5 194.5 183 208.5 216.5 231.5
NON ISO 125 <C≤ 150 178 203 204 219 204 233 241 256
NON ISO 150 <C≤ 175 199 227.5 228.5 243.5 225 257.5 265.5 280.5
NON ISO 175 <C≤ 200 220 252 253 268 246 282 290 305
NON ISO 200 <C≤ 225 241 276.5 277.5 292.5 267 306.5 314.5 329.5
NON ISO 225 <C≤ 250 262 301 302 317 288 331 339 354
2
 DIMENSIONS OF TANDEM VERSION

L1++
WH L++ VA

127

++= ADD TWICE THE STROKE

Ø WH VA R L L1
32 26 4 55 243 273
40 30 4 55 265 299
50 37 4 68 280 321
63 37 4 68 310 351
80 46 4 92 348 398
100 51 4 92 368 423
125 65 6 120 440 511

Refer to standard cylinders for other values.

DIMENSIONS OF OPPOSED VERSION

L1 + X1 + X2
WH L + X1 + X2 WH

1 2

125 X1 = STROKE CYLINDER 1

X2 = STROKE CYLINDER 2

Ø WH R L L1
32 26 55 243 295
40 30 55 265 325
50 37 68 280 354
63 37 68 310 384
80 46 92 348 440
100 51 92 368 470
125 65 120 440 570

Refer to standard cylinders for other values.

3
 BARREL CROSS SECTION

Ø50  SLOTS FOR RETRACTABLE SENSOR

Ø40 60.8
Ø32 51 11.2
44.4 1
9.4
6.5 1
1

60.8
44.4

51

Ø125
131

32

Ø100 1

Ø80 105.5

87 26.5

Ø63 20.5 1

70.9
1
16.3
1

131
105.5
87
70.9

KEY TO CODES

CYL 1 2 1 3 3 2 0 0 5 0 C N
TYPE BORE STROKE

121 Double-acting, 3 Series 3 32 For the maximum A C45 chromed rod, N NBR
cushioned 4 Series 3 40 suppliable strokes, aluminium piston rod: gaskets
122 Through-rod No stick slip 50 look at the technical standard for all cylinders P polyurethane
124 Double-acting, 5 Series 3 63 data with ≥ 1000 mm-stroke gaskets
non-cuschioned Non 80 cylinders and for cylinder
125 Opposed A1=100 with Ø 80 mm and over V FKM/FPM
magnetic gaskets
 126 Single-acting A2=125 C C45 chromed rod,
127 Tandem technopolymer piston: ●B low
134 Rod lock version standard for cylinders of temperature
136 Version with Ø 32 to Ø 63 mm with
piston rod lock < 1000 mm strokes
 137 Piston rod lock + Z Stainless steel piston
guide unit rod and nut aluminium
piston
X Stainless steel piston
rod and nut
technopolymer piston

● Only available for versions with aluminium piston (A or Z)

 Available until Ø63 and only the versions with piston in aluminum (A or Z)
 For speeds lower than 0.2m/s, to prevent surging. Use no-lubricated air only
 Available until Ø100

4
 ACCESSORIES:
MECHANICAL ROD BLOCK

Pilot pressure bar 4÷8

MPa 0.4÷0.8
Ambient temperature °C Max 80
°F Max 176
Fluid temperature °C Max 70
°F Max 154
Operation NC - bidirectional
Mechanics Double shoe with mechanical lock
Locking force F Ø32 Ø40 Ø50 Ø63 Ø80 Ø100 Ø125
(N) 650 1100 1600 2500 4000 6300 8700
Body material Aluminium
Shoe material Brass
Spring material NBR
Piston material Synthetic material with added teflon®
Gasket material NBR
Pilot port 1/8’’

Usable on cylinders type 134 or 137

OPERATING PRINCIPLE

The mechanical piston rod lock is a normally-closed mechanism. Fig. 1 Fig. 2

In the absence of pneumatic piloting, the two shoes (A) lock the
cylinder rod in both directions (Fig. 1). With pneumatic piloting,
the piston rod guide forces the shoes to come right up to each B
other and overcome the counter spring (B) force and the piston
rod can slide (Fig. 2). It is important to remember that the
mechanical piston rod lock is a static type, which means that it
is necessary to stop the cylinder piston rod pneumatically before
locking the part mechanically.
A

DIMENSIONS

L+
L1 L0+
L2 L7
T1 L4 M
D3 f8
D1

D2
D

L7

Q Z A

L8 H
+ = ADD THE STROKE

Code Ø L1 L2 L4 L7 L8 D D1 D2 D3 H A T1 M Z Q L0 L Weight [g]

W5010001102 32 58 48 8 45 34 12 30 35 25 46.5 32.5 13 M6 M6x20 M5 94 162 150
W5010001103 40 65 55 8 50 38 16 35 40 28 53 38 13 M6 M6x20 G1/8 105 180 200
W5010001104 50 82 70 15 60 48 20 40 50 35 64 46.5 16 M8 M8x30 G1/8 106 200 500
W5010001109 63 82 70 15 70 49.5 20 45 60 38 75 56.5 16 M8 M8x30 G1/8 121 215 700
W5010001106 80 110 90 18 90 61 25 45 80 48 95 72 20 M10 M10x35 G1/8 128 251 1700
W5010001107 100 115 100 18 105 68 25 55 100 58 110.5 89 20 M10 M10x35 G1/8 138 266 2700
W5010001108 125 167 122 22 140 86.5 32 60 130 65 150 110 30 M12 M12x40 G1/8 160 347 5600

5
ACCESSORIES: FIXINGS
FOOT - MODEL A Code Ø Ø AB AH AO AT AU TR E XA SA Weight [g]

XA+ W0950322001 32 7 32 11 4 24 32 45 144 142 76

W0950402001 40 9 36 15 4 28 36 52 163 161 100
W0950502001 50 9 45 15 4 32 45 65 175 170 162
W0950632001 63 9 50 15 6 32 50 75 190 185 266
W0950802001 80 12 63 20 6 41 63 95 215 210 456
W0951002001 100 14 71 25 6 41 75 115 230 220 572
AH

AT
W0951252001 125 16 90 15 7 45 90 140 270 250 1130

AB Note: ndividually packed with 2 screws.

TR AU A0
E SA+

+= ADD THE STROKE

FEMALE HINGE - MODEL B Code Ø UB CB FL ØCD XD MR L Weight [g]

W0950322003 32 45 26 22 10 142 10 10 116

W0950402003 40 52 28 25 12 160 12 10 160
W0950502003 50 60 32 27 12 170 12 12 252
R
M

W0950632003 63 70 40 32 16 190 16 12 394

W0950802003 80 90 50 36 16 210 16 16 670
W0951002003 100 110 60 41 20 230 20 16 1085
H9

W0951252003 125 130 70 50 25 275 25 20 2000

øCD

CB L Note: Supplied with 4 screws, 4 washers, 2 snap-rings, 1 pin.

UB FL
XD+

+= ADD THE STROKE

MALE HINGE - MODEL BA Code Ø EW FL MR Ø CD L XD Weight [g]

W0950322004 32 26 22 11 10 12 142 94
W0950402004 40 28 25 13 12 15 160 124
W0950502004 50 32 27 13 12 15 170 220
W0950632004 63 40 32 17 16 20 190 316
R
M

W0950802004 80 50 36 17 16 20 210 578

W0951002004 100 60 41 21 20 25 230 850
W0951252004 125 70 50 26 25 30 275 1590
øCD H9

EW L
Note: Supplied with 4 screws, 4 washers
FL
XD+

+= ADD THE STROKE

ARTICULATED MALE HINGE - MODEL BAS Code Ø DL MS L XN CX EX Weight [g]

W0950322006 32 22 16 12 142 10 14 106

W0950402006 40 25 19 15 160 12 16 142
W0950502006 50 27 19 15 170 12 16 236
MS

W0950632006 63 32 24 20 190 16 21 336

W0950802006 80 36 24 20 210 16 21 572
W0951002006 100 41 30 25 230 20 25 840
W0951252006 125 50 36 30 275 25 31 1520
H9
øCX

EX L Note: Supplied with 4 screws, 4 washers

DL
XN+

+= ADD THE STROKE

6
 CETOP HINGE FOR Code Ø A B C D E F G H I L M N Weight [g]
MODEL B - MODEL GL
D A W0950322008 32 26 19 7 10 25 20 32 37 41 18 8 10 96
W0950402008 40 28 26 9 12 32 32 45 54 52 25 10 12 216
W0950502008 50 32 26 9 12 32 32 45 54 52 25 10 12 212
W0950632008 63 40 33 11 16 40 50 63 75 63 32 12 15 440
W0950802008 80 50 33 11 16 40 50 63 75 63 32 12 15 464

B
W0951002008 100 60 44 14 20 50 70 90 103 80 40 16 22 985
W0951252008 125 70 44 14 25 50 70 90 103 80 40 16 22 1000
G

Note: Supplied with 4 screws, 4 washers

M

C N
F L E
H I

ISO HINGE FOR MODEL B - MODEL GS Code Ø B C D E G J L M N Weight [g]

B G W0950322108 32 25.5 32.5 45 7 32 11 10 10 10 106

W0950402108 40 27.5 38 52 7 36 13 10 12 12 138
J
W0950502108 50 31.5 46.5 65 9 45 13 12 12 12 252
W0950632108 63 39.5 56.5 75 9 50 17 12 16 15 350
W0950802108 80 49.5 72 95 11 63 17 16 16 15 655
W0951002108 100 59.5 89 115 11 73 21 16 20 22 980
D
C

M Note: Supplied with 4 screws, 4 washers

E

N L
C
D

FRONT FLANGE - MODEL C Code Ø TF UF E MF R ØFB W Weight [g]

W0950322002 32 64 80 50 10 32 7 16 246
MF øFB W0950402002 40 72 90 55 10 36 9 20 290
W0950502002 50 90 110 65 12 45 9 25 522
W0950632002 63 100 120 75 12 50 9 25 670
W0950802002 80 126 153 95 16 63 12 30 1420
W0951002002 100 150 178 115 16 75 14 35 2040
W0951252002 125 180 220 140 20 90 16 45 4300
UF
TF

Note: Supplied with 4 screws.

W R
E

REAR FLANGE - MODEL C Code Ø TF UF E MF R ØFB ZF Weight [g]

øFB MF W0950322002 32 64 80 50 10 32 7 130 246

W0950402002 40 72 90 55 10 36 9 145 290
W0950502002 50 90 110 65 12 45 9 155 522
W0950632002 63 100 120 75 12 50 9 170 670
W0950802002 80 126 153 95 16 63 12 190 1420
W0951002002 100 150 178 115 16 75 14 205 2040
UF
TF

W0951252002 125 180 220 140 20 90 16 245 4300

Note: Supplied with 4 screws.

R ZF+
E

+= ADD THE STROKE

7
ROD NUT - MODEL S Code Ø F H CH Weight [g]

0950322010 32 M10x1.25 6 17 6
0950402010 40 M12x1.25 7 19 12
0950502010 50 M16x1.5 8 24 20
0950502010 63 M16x1.5 8 24 20
0950802010 80 M20x1.5 9 30 32
0950802010 100 M20x1.5 9 30 32
F

0951252010 125 M27x2 12 41 74

Note: Individually packed.

CH H

FORK MODEL GK-M Code Ø ØM C B A L F D N Weight [g]

L W0950322020 32 10 20 10 20 52 40 M10x1.25 26 92
W0950402020 40 12 24 12 24 62 48 M12x1.25 32 148
F
W0950502020 50 16 32 16 32 83 64 M16x1.5 40 340
W0950502020 63 16 32 16 32 83 64 M16x1.5 40 340
W0950802020 80 20 40 20 40 105 80 M20x1.5 40 690
A

W0950802020 100 20 40 20 40 105 80 M20x1.5 48 690

W0951252020 125 30 54 30 55 148 110 M27x2 65 1835
øM

Note: Individually packed.

B B12
N

ROD EYE - MODEL GA-M Code Ø Ø M C B1 B A L F D Ø G CH Ø G1 Weight [g]

W0950322025 32 10 15 10.5 14 28 57 43 M10x1.25 15 17 19 78

C CH
W0950402025 40 12 17 12 16 32 66 50 M12x1.25 17.5 19 19 116
W0950502025 50 16 22 15 21 42 85 64 M16x1.5 22 22 22 226
W0950502025 63 16 22 15 21 42 85 64 M16x1.5 22 22 22 226
øG1
øG
A

W0950802025 80 20 26 18 25 50 102 77 M20x1.5 27.5 30 27 404

W0950802025 100 20 26 18 25 50 102 77 M20x1.5 27.5 30 27 404
W0951252025 125 30 36 25 37 70 145 110 M27x2 40 41 50 1190
øM H7

Note: Individually packed

-0.12
+0

B1

D
B

SELF ALIGNING ROD COUPLER - MODEL GA-K Code Ø A B C D ØF ØE SW1 SW2 SW3 SW4 SW5 Weight [g]

W0950322030 32 M10x1.25 20 20 71 22 4 12 30 30 19 17 216

C
SW5 SW1 SW4 W0950402030 40 M12x1.25 24 20 75 22 4 12 30 30 19 19 220
W0950502030 50 M16x1.5 32 32 103 32 4 20 41 41 30 24 620
øE

W0950502030 63 M16x1.5 32 32 103 32 4 20 41 41 30 24 620

W0950802030 80 M20x1.5 40 40 119 32 4 20 41 41 30 30 680
W0950802030 100 M20x1.5 40 40 119 32 4 20 41 41 30 30 680
5°

øF
A

5° Note: Individually packed

B SW2 SW3
D

8
 ACCESSORIES: MAGNETIC SENSORS
RETRACTABLE SENSOR WITH INSERTION Code Description
FROM ABOVE
W0952025390 HALL N.O. SENSOR, VERTICAL INSERTION 2.5m
W0952029394 HALL N.O. SENSOR, VERTICAL INSERTION 300 mm M8
W0952022180 REED N.O. SENSOR, VERTICAL INSERTION 2.5m
W0952028184 REED N.O. SENSOR, VERTICAL INSERTION 300 mm M8
W0952125556 HALL N.O. SENSOR, VERTICAL INSERTION 2m ATEX

This type of sensor can be inserted in the slot of the sensor from above. This means the
cylinder heads do not require a through opening.

WIRING DIAGRAM TECHNICAL DATA ATEX

Reed Effetto Hall Effetto Hall
Type of contact N.O. N.O. N.O.
Switch - PNP PNP
Supply voltage (Ub) V 10 ÷ 30 AC/DC 10 ÷ 30 DC 18 ÷ 30 DC
Power W 3 (peak valve=6) 3 ≤ 1.7
Voltage variation - ≤ 10% di Ub ≤ 10% di Ub
REED EFFECT brown +
Voltage drop V - ≤2 ≤ 2.2
Input current mA - ≤ 10 ≤ 10
-
blue + Output current mA ≤ 100 ≤ 100 ≤ 70
Switching frequency Hz ≤ 400 ≤ 5000 1000
M8

4
blue 1 3 Short-circuit protection - Yes Yes
brown Over-voltage suppression - Yes Yes
Polarity inversion protection - Yes Yes
brown + EMC
HALL EFFECT EN 60 947-5-2 EN 60 947-5-2 EN 60 947-5-2
black + LED display Yellow Yellow Yellow
-
PNP Magnetic sensitivity 2,8 mT ±25% 2,8 mT ±25% 2.6
Repeatability ≤ 0,1 mT ≤ 0,1 mT ≤ 0,1 (Ub and ta fixed)
blue
Degree of protection (EN 60529) IP 67 IP 67 IP 68, IP 69K
M8

4
black 1 3 Vibration and shock resistance 30 g, 11 ms, 10÷55 Hz, 1mm 30 g, 11 ms, 10÷55 Hz, 1mm 30 g, 11 ms, 10÷55 Hz, 1mm
brown blue Temperature range °C -25 ÷+75 -25 ÷ +75 -20 ÷ +45
Sensor capsule material PA66 + PA6I/6T PA66 + PA6I/6T PA
2.5m/2m connecting cable PVC; 2 x 0,12 mm2 PVC; 3 x 0,14 mm2 PVC; 3 x 0,12 mm2
Connecting cable with M8x1 Polyurethane; 2 x 0,14 mm2 Polyurethane; 3 x 0,14 mm2 -
Wire NO. 2 3 3

STRIP

Code Description
5.8 500
W0950000160 SLOT STRIP 500 mm

Note: The code corresponds to 1 piece.

4.9

KIT FOR CYLINDER ASSEMBLY Code Description Weight [g]

WITH SENSOR SLOTS
0950003001 ACC. M4 T-SLOTTED FIXING PLATE 1
0950003002 ACC. M3 T-SLOTTED FIXING PLATE 1

Note: Individually packed

9
SENSOR MOD. DSM
Code Description
W0950000201 REED SENSOR ACC. DSM2-C525 HS
9.1
W0950000222 E.HALL PNP SENSOR ACC. DSM3-N225
W0950000232 E. HALL NPN SENSOR ACC. DSM3-M225

17

11.5
34 25.5

SENSOR SUPPORT BRACKETS

Ø 32÷40 Ø 50÷63 Ø 80÷100÷125

M5

25.9
M5

26
18.5

19.2

20.4

20.9
1.7

2.7 20.6 7.5

14 14 1.6
47.8
13.2 5.9 14.8 1.8

M5
29.5 29.8

14
Code Description Code Description Code Description
W0950000711 BRACKET ACC. D.32 DST 80 W0950000712 BRACKET ACC. D.50 DST 81 W0950000713 BRACKET ACC. D.80-100-125 DST 82

TECHNICAL DATA
Type REED + VARISTORE + LED 2 fili HALL VERSION PNP/NPN 3 wires
Contact REED + VARISTORE + LED N.O. HALL EFFECT NO PNP/NPN
Max AC/DC voltage V 3÷48 V(DC); 3÷220 (AC) 6-24 V DC
Max current at 25°C mA 500 250
Power with inductive load VA 10 –
Power with resistive load Watt 50 6
Switch-on time m sec 1.2 0.8
Switch-off time m sec 0.1 3
Switch-on point Gauss 110 15
Switch-off point Gauss 95 8
Operating life – 107 impulsi 109 impulses
Contact resistance 0.1 –
Cable length m 2.5 2.5
Cable cross section mm2 0.35 0.35
Cable material PVC Morbido Soft PVC
Circuit
DC Versione NPN
brown + brown +

blue
black

blue -

24VAC
AC Versione PNP
brown ~ brown +

blue black

blue
-

10
 ADAPTOR FOR RETRACTABLE SENSOR

Code Description
W0950001001 Adaptor DSS005 for DST/ST brackets

ASSEMBLY DIAGRAM

 ISO 15552 cylinder with traditional barrel

 Sensor bracket mod. DST (Ø32÷125) 4 2 1
 Adaptor
 Retractable sensor with insertion from above

SPARES

1 4 15 9 13 11 17 5 8

2 3 16 10 12 18

Type Parts Bore Code

Complete set of polyurethane gaskets 2-4-5-9-10 Ø 32÷125 009 . . . 0101
Complete set of NBR gaskets 2-4-5-9-10 Ø 32÷125 009 . . . 0502
Complete polyurethane front head kit 1-2-3-4-5-17-18 Ø 32÷125 009 . . . 0110N
Complete NBR front head kit 1-2-3-4-5-17-18 Ø 32÷125 009 . . . 0304N
Complete polyurethane rear head kit 4-5-8-17-18 Ø 32÷125 009 . . . 0111N
Complete NBR rear head kit 4-5-8-17-18 Ø 32÷125 009 . . . 0305N
Complete polyurethane piston kit 9-10-16-17 Ø 32÷63 009 . . . 0604
Complete polyurethane piston kit 9-10-11-13-15-18 Ø 80÷125 009 . . . 0604
Complete NBR piston kit 9-10-16-17 Ø 32÷63 009 . . . 0602
Complete NBR piston kit 9-10-11-13-15-18 Ø 80÷125 009 . . . 0602
Complete polyurethane head A+P+piston kit 1-2-3-4-5-8-9-10-16-17-18 Ø 32÷63 009 . . . 0704N
Complete polyurethane head A+P+piston kit 1-2-3-4-5-8-9-10-11-13-15-17-18 Ø 80÷125 009 . . . 0704N
Complete NBR head A+P+pistion kit 1-2-3-4-5-8-9-10-14-16-17-18 Ø 32÷63 009 . . . 0702N
Complete NBR head A+P+piston kit 1-2-3-4-5-8-9-10-11-13-15-17-18 Ø 80÷125 009 . . . 0702N
Magnet 12 Ø 32÷125 009 . . . 0800
11
ACCESSORIES: GUIDE UNITIS

Guide units series DS-DH-DM ensure optimal alignment

and anti-rotation effect of the pneumatic cylinder connected
to it. The guide units can be used separately or combined
in order to get complete handling units, in which case the
guide units can be coupled using the type A and C
anchorage (pin and flange).
The guide units can be coupled to ISO 15552 cylinders
(Ø 32 - Ø 100). The following versions are available:
U PROFILE*: for limited loads and speeds (GDS)
H PROFILE*: for high loads (GDH)
H PROFILE**: for high speeds (GDM)

STANDARD STROKES:
Ø 32-100: 50-100-150-200-250-320-400-500

**Bronze guide bushings

**Ball guide bushings
(For weights, refer to the data sheet on page 16)

GUIDE UNIT ELEMENTS

SERIES GDS-GDH Body: aluminium alloy
Guide bushing: self-lubricating sintered bronze and wiper rings
Piston rod: chromed rolled steel

SERIES GDM Body: aluminium alloy

Guide bushing: ball linear bearings and scraper ring
Piston rod: tempered stainless steel

12
 GRAPH OF GUIDE UNIT LOADS

1000

900
S
800

700
B

600

P
GD

500 S = PROJECTION
H

B = BARYCENTRE
80

P = PAY LOAD
GD

•1
G
DM

00
M
50

80

400
•
10
GD

0
GD

GD
GD 63

H
M
P (N)

M4

H4

63

300
0

200
DH
GD

50
GD
M3

S8
2

0
•

160
10
0
GD

120
S 32

G
DS
•

100 50
40

G
D

•
H

63
32

80

50

30

10
50 100 150 200 250 300 350 400 450 500 550 600
S (mm)

13
DIMENSIONS TYPE GDS

E1 O G C1
H
Y

B1
E2

E3
B
E

I
D*
F2 depth 10
F CH

F1

E L1+ N M
X
A L+
F2 depth 10 F

A1
øS

E
VIEW X-Y
E O1
+ = ADD THE STROKE
C
 CENTERING PINHOLES

Ø A A1 B B1 C C1 DH7 E E1 E2 E3 F F1 F2H7 G H I L L1 M N O O1 ØS Ch
32 48 45 100 95 48 12 6 32.5 32.5 78 58 M6 6.5 6 18 31 74 108 94 46 17 7.8 7.8 12 15
40 56 53 106 101 58 15 6 38 38 84 64 M6 6.5 6 21 36 80 120 105 52 21 10 10 12 15
50 66 63 125 120 59 15 6 46.5 46.5 100 80 M8 8.5 6 24 45 96 130 106 65 25 6.3 6.3 16 22
63 76 73 132 127 76 15 6 56.5 56.5 105 95 M8 8.5 6 24 45 104 145 121 65 25 9.8 9.8 16 22
80 98 95 165 160 90 16 6 72 50 130 130 M10 11 6 31 56 130 170 128 71 34 20 9 20 27
100 118 115 185 180 110 16 6 89 70 150 150 M10 11 6 31 56 152 190 138 71 39 20 10.5 20 27

DIMENSIONS TYPE GDH-GDM

E
H G C1 Y
O

U F
B1
E2

E3
B
E

D*
F2 depth 10
CH
F

F1

E L1+ N M
X
L+
A
C

F2 depth 10
A1
øS

VIEW X-Y
F
+ = ADD THE STROKE
E
 CENTERING PINHOLES

Ø A A1 B B1 C C1 Ch DH7 E E2 E3 F F1 F2H7 G H I L L1 M N O ØS U
32 49 45 97 90 125 12 13 6 32.5 78 61 M6 6.5 6 18 31 74 177 94 47 17 4.3 12 76
40 58 54 115 110 139 15 15 6 38 84 69 M6 6.5 6 21 36 87 192 105 53 21 11 16 81
50 69 63 137 130 148 15 22 6 46.5 100 85 M8 8.5 6 24 45 104 205 106 63 26 18.5 20 78
63 85 79 152 145 182 15 22 6 56.5 105 100 M8 8.5 6 24 45 119 237 121 62 26 15.3 20 111
80 105 99 189 180 215 20 27 6 72 130 130 M10 11 6 31 56 148 280 128 76 34 21 25 128
100 129 120 213 200 220 20 27 6 89 150 150 M10 11 6 31 56 172 280 138 76 39 24.5 25 128

14
 GUIDE UNIT

Version Bore Type Code

32 UNIT MW DS 032... W 0700321...
Sliding on bronze bushings (GDS) 40 UNIT MW DS 040... W 0700401...
50 UNIT MW DS 050... W 0700501...
63 UNIT MW DS 063... W 0700631...
80 UNIT MW DS 080... W 0700801...
100 UNIT MW DS 100... W 0701001...

32 UNIT MW DH 032... W 0700322...

Sliding on bronze bushings (GDH) 40 UNIT MW DH 040... W 0700402...
50 UNIT MW DH 050... W 0700502...
63 UNIT MW DH 063... W 0700632...
80 UNIT MW DH 080... W 0700802...
100 UNIT MW DH 100... W 0701002...

32 UNIT MW DM 032... W 0700323...

Sliding on ball bearing (GDM) 40 UNIT MW DM 040... W 0700403...
50 UNIT MW DM 050... W 0700503...
63 UNIT MW DM 063... W 0700633...
80 UNIT MW DM 080... W 0700803...
100 UNIT MW DM 100... W 0701003...

Note: To complete the type and code, add the 3-digit stroke (e.g. 50=050)

DIMENSIONS PISTON ROD LOCK + GUIDE UNIT COD. 137

Bore C
32 74
40 85
50 107
63 107
80 136
100 143

15
GENERALE TECHNICAL DATE
FORCES GENERATED DURING THRUST AND TRACTION (THEORETICAL)

Cylinder Piston rod Useful Thrust and traction force in daN depending on the operating pressure in bar.
bore D diameter d Motion area
mm mm cm2 1 bar 2 bar 3 bar 4 bar 5 bar 6 bar 7 bar 8 bar 9 bar 10 bar
32 12 thrust 8.04 8.0 16.1 24.1 32.2 40.2 48.3 56.3 64.3 72.4 80.4
traction 6.91 6.9 13.8 20.7 27.6 34.6 41.5 48.4 55.3 62.2 69.1
40 16 thrust 12.57 12.6 25.1 37.7 50.3 62.8 75.4 88.0 100.5 113.1 125.7
traction 10.56 10.6 21.1 31.7 42.2 52.8 63.3 73.9 84.4 95.0 105.6
50 20 thrust 19.63 19.6 39.3 58.9 78.5 98.2 117.8 137.4 157.1 176.7 196.3
traction 16.49 16.5 33.0 49.5 66.0 82.5 99.0 115.5 131.9 148.4 164.9
63 20 thrust 31.17 31.2 62.3 93.5 124.7 155.9 187.0 218.2 249.4 280.6 311.7
traction 28.03 28.0 56.1 84.1 112.1 140.2 168.2 196.2 224.2 252.3 280.3
80 25 thrust 50.27 50.3 100.5 150.8 201.1 251.3 301.6 351.9 402.1 452.4 502.7
traction 45.36 45.4 90.7 136.1 181.4 226.8 272.1 317.5 362.9 408.2 453.6
100 25 thrust 78.54 78.5 157.1 235.6 314.2 392.7 471.2 549.8 628.3 706.9 785.4
traction 73.63 73.6 147.3 220.9 294.5 368.2 441.8 515.4 589.0 662.7 736.3
125 32 thrust 122.72 122.7 245.4 368.2 490.9 613.6 736.3 859.0 981.7 1104.5 1227.2
traction 114.68 114.7 229.4 344.0 458.7 573.4 688.1 802.7 917.4 1031.1 1146.8

WEIGHT OF CYLINDERS

Cylinder “ISO 15552” Series 3 Guide unit

Single-rod Through-rod Type GDS Type GDH and GDM
Ø Weight [g] Weight [g] Weight [g] Weight [g] Ø Weight [g] Weight [g] Weight [g] Weight [g]
Stroke=0 each mm Stroke=0 each mm Stroke=0 each mm Stroke=0 each mm
32 434 2.30 495 3.19 32 772 1.76 1200 1.76
40 660 3.22 783 4.80 40 1000 1.76 2000 3.13
50 1079 4.50 1340 6.97 50 1900 3.13 3300 4.9
63 1427 4.78 1702 7.24 63 2300 3.13 4750 4.9
80 2774 6.73 3219 10.58 80 3800 4.9 8500 7.26
100 3836 7.73 4364 11.58 100 7000 4.9 12000 7.26
125 6529 11.63 7581 17.94

NOTES

www.metalwork.eu
The dimensions shown in this catalogue are subject to variations at any time without prior notice

MNWS01064 - IM01 - 01/2011 16