SRV ENGINEERING COLLEGE B.

E (ELECTRONICS & COMMUNICATION ENGINEERING)

CIRCUIT DIAGRAM:
VCC
5V Transformer

R1 L2 L1 C2
1kΩ 1mH 1mH 1µF

C1
Output
1µF U1
Q
2N2219
R2
1kΩ
R3 C3
1kΩ 1µF

Ex. no:
Date:
SPICE SIMULATION OF TUNED COLLECTOR OSCILLATOR
Aim:
To simulate a Tuned collector oscillator circuit and to plot the frequency response
characteristics.

Apparatus required :

i)Personal Computer
ii) SPICE (PSPICE 9.0 v& above or MULTISIM 10.0 v & above) Software.

Procedure:

i) Draw the circuit diagram after loading components from library.

ii) A DC source with 0 V is place as the dummy voltage source to obtain the current waveform.
iii) Wiring and proper net assignment has been made. The circuit is preprocessed. The VI
characteristics may be obtained by performing DC transfer function Analysis. Place the current
waveform marker at the positive terminal of the dummy voltage source (voltage =0 volts).
Iv) For placing waveform markers, select tools instruments set wave form conent current waveform
click on the required net and place the waveform marker.The sweep parameter (voltage) for input
source is set in the Analysis window.
V) The applied voltage is swept from an initial value to final value with the steps provided To get VI
characteristics, the currents corresponding to varying input voltages are noted.
vi) The VI graph is observed in the Waveform Viewer

Result :

Thus the Tuned collector oscillator is simulated successfully.

58
EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC
SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

Circuit Diagram :
WEIN BRIDGE OSCILLATOR
VCC
5V

R5 R8 R7 R10
1kΩ 1kΩ 1kΩ 1kΩ

C3
C4
C2 R2
750nF
1kΩ U1 U2 750nF
750nF
R3
R1 Tank circuit 1kΩ

1kΩ R4 BC107BP BC107BP

R6 R9
C1 1kΩ 1kΩ Output
1kΩ C5
R11 750nF
750nF 1kΩ

TWIN T OSCILLATOR:

EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC

SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

Ex. no:
Date:
SPICE SIMULATION OF WEIN BRIDGE AND TWIN T OSCILLATOR
Aim:
To simulate a Wein Bridge and Twin T oscillator circuit and to plot the frequency response
characteristics.

Apparatus required :

i)Personal Computer
ii) SPICE (PSPICE 9.0 v& above or MULTISIM 10.0 v & above) Software.

Procedure:

i) Draw the circuit diagram after loading components from library.

ii) A DC source with 0 V is place as the dummy voltage source to obtain the current waveform.
iii) Wiring and proper net assignment has been made. The circuit is preprocessed. The VI
characteristics may be obtained by performing DC transfer function Analysis. Place the current
waveform marker at the positive terminal of the dummy voltage source (voltage =0 volts).
Iv) For placing waveform markers, select tools instruments set wave form conent current waveform
click on the required net and place the waveform marker. The sweep parameter (voltage) for input
source is set in the Analysis window.
V) The applied voltage is swept from an initial value to final value with the steps provided To get VI
characteristics, the currents corresponding to varying input voltages are noted.
vi) The VI graph is observed in the Waveform Viewer
.

Result :

Thus the Wein Bridge and Twin T oscillator circuit is simulated successfully.

60
EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC
SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

CIRCUIT DIAGRAM:

DOUBLE TUNED AMPLIFIER

V1
12 V

C3 T1 C4
R4
30pF 30pF 1mΩ Output
50% 40%
Key=A Key=A
NLT_PQ_4_10
R1
1mΩ
U1
C2

750nF
BC107BP
V2

120 Vrms R3 C1
R2 1mΩ 750nF
60 Hz 1mΩ
0°

STAGGER TUNED AMPLIFIER

VCC
5V

C6 L2
C3 L1 750nF 1mH
750nF 1mH C7
R1 C5 R3 Output
1mΩ 1mΩ 750nF
U2
750nF
U1
C1

BC107BP
750nF
BC107BP
R2 R4 R5
1mΩ R6 C2 1mΩ 1mΩ C4
1mΩ 750nF 750nF

EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC

SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

Ex. no:
Date:
SPICE SIMULATION OF DOUBLE AND STAGGER TUNED AMPLIFIERS
Aim:
To simulate a Double and Stagger tuned Amplifiers circuit and to plot the frequency response
characteristics.

Apparatus required :

i) Personal Computer
ii) SPICE (PSPICE 9.0 v& above or MULTISIM 10.0 v & above) Software.

Procedure:

i) Draw the circuit diagram after loading components from library.

ii) A DC source with 0 V is place as the dummy voltage source to obtain the current waveform.
iii) Wiring and proper net assignment has been made. The circuit is preprocessed. The VI
characteristics may be obtained by performing DC transfer function Analysis. Place the current
waveform marker at the positive terminal of the dummy voltage source (voltage =0 volts).
Iv) For placing waveform markers, select tools instruments set wave form conent current waveform
click on the required net and place the waveform marker.The sweep parameter (voltage) for input
source is set in the Analysis window.
V) The applied voltage is swept from an initial value to final value with the steps provided To get VI
characteristics, the currents corresponding to varying input voltages are noted.
vi) The VI graph is observed in the Waveform Viewer

Result :

Thus the Double and Stagger tuned Amplifier were simulated successfully.

62
EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC
SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

CIRCUIT DIAGRAM:

BI STABLE MULTIVIBRATOR
Ex. no:
Date:
SPICE SIMULATION OF BI STABLE MULTIVIBRATOR
Aim:
To simulate a Bistable Multivibrator circuit and to plot the frequency response characteristics.

Apparatus required :

i) Personal Computer
ii) SPICE (PSPICE 9.0 v& above or MULTISIM 10.0 v & above) Software.

Procedure:

i) Draw the circuit diagram after loading components from library.

ii) A DC source with 0 V is place as the dummy voltage source to obtain the current waveform.
iii) Wiring and proper net assignment has been made. The circuit is preprocessed. The VI
characteristics may be obtained by performing DC transfer function Analysis. Place the current
waveform marker at the positive terminal of the dummy voltage source (voltage =0 volts).
Iv) For placing waveform markers, select tools instruments set wave form conent current waveform
click on the required net and place the waveform marker.The sweep parameter (voltage) for input
source is set in the Analysis window.
V) The applied voltage is swept from an initial value to final value with the steps provided To get VI
characteristics, the currents corresponding to varying input voltages are noted.
vi) The VI graph is observed in the Waveform Viewer
Result :

Thus the Bistable Multivibrator was simulated successfully.

EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC

SRV ENGINEERING COLLEGE B.E (ELECTRONICS & COMMUNICATION ENGINEERING)

CIRCUIT DIAGRAM:

SCHMITT TRIGGER

Ex. no:
Date:
SPICE SIMULATION OF SCHMITT TRIGGER
Aim:
To simulate a Schmitt trigger circuit and to plot the frequency response characteristics.

Apparatus required :

i) Personal Computer
ii) SPICE (PSPICE 9.0 v& above or MULTISIM 10.0 v & above) Software.

Procedure:

i) Draw the circuit diagram after loading components from library.

ii) A DC source with 0 V is place as the dummy voltage source to obtain the current waveform.
iii) Wiring and proper net assignment has been made. The circuit is preprocessed. The VI
characteristics may be obtained by performing DC transfer function Analysis. Place the current
waveform marker at the positive terminal of the dummy voltage source (voltage =0 volts).
Iv) For placing waveform markers, select tools instruments set wave form conent current waveform
click on the required net and place the waveform marker.The sweep parameter (voltage) for input
source is set in the Analysis window.
V) The applied voltage is swept from an initial value to final value with the steps provided To get VI
characteristics, the currents corresponding to varying input voltages are noted.
vi) The VI graph is observed in the Waveform Viewer

Result :

Thus the Schmitt Trigger was simulated successfully.

64
EC6411-CIRCUITS & SIMULATION INTEGRATED LAB R.SHANKARANARAYANAN,AP/ECE/SRVEC