Sony cdx-s2050c s2050v Ver.1.0

CDX-S2050C/S2050V
SERVICE MANUAL AEP Model

UK Model
Ver. 1.0 2005.01
• The tuner and CD sections have no adjustments.

Model Name Using Similar Mechanism CDX-S2050
CD Drive Mechanism Type MG-611XE-186//K
Optical Pick-up Name KSS1000E
SPECIFICATIONS
CD Player section Power amplifier section
Signal-to-noise ratio: 120 dB Outputs: Speaker outputs (sure seal connectors)
Frequency response: 10 – 20,000 Hz Speaker impedance: 4 – 8 ohms
Wow and flutter: Below measurable limit Maximum power output: 50 W × 4 (at 4 ohms)
Tuner section General

FM Outputs: Audio outputs terminal (rear/sub switchable)
Tuning range: 87.5 – 108.0 MHz Power aerial relay control terminal
Aerial terminal: External aerial connector Power amplifier control terminal
Intermediate frequency: 10.7 MHz/450 kHz Inputs: Telephone ATT control terminal
Usable sensitivity: 9 dBf Remote controller input terminal
Selectivity: 75 dB at 400 kHz Aerial input terminal
Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono) Tone controls: Low: ±10 dB at 60 Hz (XPLOD)
Harmonic distortion at 1 kHz: Mid: ±10 dB at 1 kHz (XPLOD)
0.5 % (stereo), 0.3 % (mono) High: ±10 dB at 10 kHz (XPLOD)
Separation: 35 dB at 1 kHz Power requirements: 12 V DC car battery (negative earth)
Frequency response: 30 – 15,000 Hz Dimensions: Approx. 178 × 50 × 178 mm (w/h/d)
Mounting dimensions: Approx. 182 × 53 × 161 mm (w/h/d)
MW/LW Mass: Approx. 1.2 kg
Tuning range: MW: 531 – 1,602 kHz Supplied accessories: Parts for installation and connections (1 set)
LW: 153 – 279 kHz Front panel case (1)
Aerial terminal: External aerial connector
Intermediate frequency: 10.7 MHz/450 kHz Design and specifications are subject to change
Sensitivity: MW: 30 µV, LW: 40 µV without notice.
FM/MW/LW COMPACT DISC PLAYER

9-879-403-01 Sony Corporation
2005A04-1 e Vehicle Company
© 2005.01 Published by Sony Engineering Corporation
1
CDX-S2050C/S2050V
SERVICE NOTES If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
CAUTION pick-up block.
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation optical pick-up
exposure.
This compact disc player is classified as a CLASS 1 LASER

product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
This label is located on the bottom of the chassis.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic semi-fixed resistor
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
TEST DISCS
parts.
This set can playback CD-R and CD-ROM discs. The following
The flexible board is easily damaged and should be handled with
test discs should be used to check the capability:
care.
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
NOTES ON LASER DIODE EMISSION CHECK
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
CDX-S2050C/S2050V
Notes on CD-DA/CD-R/CD-RW z UNLEADED SOLDER

• CD playback: Boards requiring use of unleaded solder are printed with the lead
You can play CD-DA and CD-R/CD-RW for audio use. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION

When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD J-2502-076-1

CNP301
SERVO BOARD
CN1
3
CDX-S2050C/S2050V
TABLE OF CONTENTS
1. GENERAL
Location of controls and basic operations ............................... 5
Connections ............................................................................. 6
2. DISASSEMBLY
2-1. Sub Panel (LCD) Assy ........................................................ 8
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 9
2-4. Chassis (T) Sub Assy .......................................................... 9
2-5. Roller Arm Assy ................................................................ 10
2-6. Chassis (OP) Assy ............................................................. 10
2-7. Optical Pick-up ................................................................. 11
2-8. SL Motor Assy (M902) ..................................................... 11
2-9. LE Motor Assy (M903) ..................................................... 12
2-10. Servo Board ....................................................................... 12
3. DIAGRAMS
3-1. Block Diagram – CD Section – ......................................... 13
3-2. Block Diagram – Main Section – ...................................... 14
3-3. Block Diagram – Display Section – .................................. 15
3-4. Printed Wiring Boards – Servo Board – ............................ 17
3-5. Schematic Diagram – Servo Board – ................................ 18
3-6. Printed Wiring Board – Main Board – .............................. 19
3-7. Schematic Diagram – Main Board (1/4) – ........................ 20
3-11. Printed Wiring Board – Key Board (S2050C) – ............... 24
3-12. Schematic Diagram – Key Board (S2050C) – .................. 25
3-13. Printed Wiring Board – Key Board (S2050V) – ............... 26
3-14. Schematic Diagram – Key Board (S2050V) – .................. 27
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 34
4-2. Front Panel Section ........................................................... 35
4-3. CD Mechanism Section (1) (MG-611XE-186//K) ............ 36
5. ELECTRICAL PARTS LIST ......................................... 40
4
CDX-S2050C/S2050V
SECTION 1
GENERAL This section is extracted
from instruction manual.
Location of controls and basic operations

Main unit
1 2 34 5 6 7 8 9 0
SEL
SOURCE MODE ATT EQ3 SEEK
DIM BTM REP SHUF

DSPL SENS 1 2 3 4 5 6 PTY AF/TA OFF
CDX-S2050V
qa qs qd qf qg qh qj qk CDX-S2050C
CDX-S2050 ql
Refer to the pages listed for details.
a Volume +/– button n RESET button (located behind the front
To adjust volume. panel) 4
b SEL (select) button 4, 9 o Number buttons
To select items. Radio:
c SOURCE button To receive stored stations (press); store
To power on/change the source (Radio/CD). stations (press and hold).
d MODE button 7 CD:
To select the radio band (FM/MW/LW). (3): REP
e Disc slot To play the current track/disc repeatedly.
Insert the disc (label side up), playback (4): SHUF
starts. To play the tracks in random order.
f Display window p PTY (Programme Type) button 8
g ATT (attenuate) button To select PTY in RDS.
To attenuate the sound. To cancel, press q AF (Alternative Frequencies)/TA
again. (Traffic Announcement) button 8
h EQ3 (equalizer) button 9 To set AF and TA/TP in RDS.
To select an equalizer curve (XPLOD, r OFF button
VOCAL, CLUB, JAZZ, NEW AGE, ROCK To power off/stop the source.
and CUSTOM). s Receptor for the card remote
i Z (eject) button commander 10
To eject the disc.
j SEEK +/– button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); fast-forward/reverse a
track (press and hold).
k (front panel release) button 4
l DSPL (display)/DIM (dimmer) button
4, 7
To change display items (press); change the
display brightness (press and hold).
m SENS/BTM button 7
To improve weak reception: LOCAL/MONO
(press); start the BTM function (press and
hold).
5
CDX-S2050C/S2050V
Connections
*1 Note for the aerial connecting *1 Remarque sur le raccordement de *1 Opmerking bij de antenne-aansluiting
If your car aerial is an ISO (International l’antenne Indien uw auto is uitgerust met een
Organisation for Standardisation) type, Si votre antenne de voiture est de type antenne van het type ISO (International
use the supplied adaptor 2 to connect ISO (Organisation internationale de Organisation for Standardization),
it. First connect the car aerial to the normalisation), utilisez l’adaptateur fourni moet u die aansluiten met behulp
supplied adaptor, then connect it to the 2 pour la raccorder. Raccordez d’abord van de bijgeleverde adapter 2. Sluit
aerial jack of the master unit. l’antenne de voiture à l’adaptateur fourni eerst de auto-antenne aan op de
*2 *2 RCA pin cord (not supplied) et, ensuite, à la prise d’antenne de meegeleverde adapter en vervolgens de
3
* AUDIO OUT can be switched REAR l’appareil principal. antennestekker op het hoofdtoestel.
or SUB. For details, see the Operating *2 Cordon à broche RCA (non fourni) *2 Tulpstekkersnoer (niet bijgeleverd)
AUDIO OUT REAR*3 Instructions manual. *3 AUDIO OUT peut être commuté sur *3 AUDIO OUT kan worden ingesteld
*4 Insert with the cord upwards REAR ou SUB. Pour obtenir plus de op REAR of SUB. Raadpleeg de
*4 *5 CDX-S2050V/S2050C/S2050 only détails, reportez-vous au mode d’emploi. handleiding met gebruiksaanwijzingen
*4 Insérez avec le câble vers le haut voor meer informatie.
*1 Hinweis zum Anschließen der Antenne *5 CDX-S2050V/S2050C/S2050 *4 Plaatsen met het snoer naar boven naar
Wenn Ihre Fahrzeugantenne der uniquement boven
ISO-Norm (ISO = International *5 Alleen voor de CDX-S2050V/S2050C/
AUDIO
OUT Organization for Standardization *1 Nota per il collegamento dell’antenna S2050
- Internationale Normungsgemeinschaft) Se l’antenna dell’auto è di tipo
entspricht, schließen Sie sie mithilfe des ISO (International Organization for
2 Fuse (10 A) mitgelieferten Adapters 2 an. Verbinden Standardization), utilizzare l’adattatore
*1 from car aerial Sicherung (10 A) REMOTE IN*5 Sie zuerst die Fahrzeugantenne mit dem 2 in dotazione per collegarla. Collegare
von Autoantenne mitgelieferten Adapter und verbinden Sie prima l’antenna della macchina
Fusible (10 A)
de l’antenne de la voiture diesen dann mit der Antennenbuchse all’adattatore in dotazione, quindi
Fusibile (10 A)
dall’antenna dell’auto des Hauptgeräts. collegarla alla presa dell’antenna
Zekering (10 A)
van een auto-antenne *2 Cinchkabel (nicht mitgeliefert) dell’apparecchio principale.
3 *3 AUDIO OUT kann zwischen REAR *2 Cavo a piedini RCA (non in dotazione)
und SUB umgeschaltet werden. *3 AUDIO OUT può essere impostato
Näheres hierzu finden Sie in der su REAR o su SUB. Per ulteriori
Bedienungsanleitung. informazioni, consultare il manuale di
Max. supply current 0.3 A Blue/white striped *4 Mit dem Kabel nach oben einsetzen istruzioni per l’uso.
max. Versorgungsstrom 0,3 A Blauweiß gestreift *5 Nur CDX-S2050V/S2050C/S2050 *4 Inserire con il cavo rivolto verso l’alto 1 3 5 7
Courant d’alimentation maximum 0,3 A Rayé bleu/blanc *5 Solo CDX-S2050V/S2050C/S2050
Alimentazione massima fornita 0,3 A Rigato blu e bianco from the car’s speaker connector
Max. voedingsstroom 0,3 A AMP REM Blauw/wit gestreept vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore del diffusore dell’auto
van de autoluidsprekerstekker
2 4 6 8
Light blue
Hellblau
Bleu ciel
5 7 Speaker, Rear, Right Speaker, Front, Left
Azzurro from the car’s power connector Lautsprecher hinten rechts Lautsprecher vorne links
ATT Lichtblauw vom Stromanschluss des Fahrzeugs 1 + Haut-parleur, arrière, droit 5 + Haut-parleur, avant, gauche
Purple Diffusore, posteriore, destro White Diffusore, anteriore, sinistro
du connecteur d’alimentation de la voiture
Violett Luidspreker, achter, rechts Weiß Luidspreker, voor, links
dal connettore di alimentazione dell’auto
Mauve Blanc
van de autovoedingsstekker Speaker, Rear, Right Speaker, Front, Left
Viola Bianco
Paars Lautsprecher hinten rechts Wit Lautsprecher vorne links
4 8 2 – Haut-parleur, arrière, droit 6 – Haut-parleur, avant, gauche
Diffusore, posteriore, destro Diffusore, anteriore, sinistro
See “Power connection diagram” on the reverse side for details. Luidspreker, achter, rechts Luidspreker, voor, links
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern Yellow continuous power supply Red switched power supply Speaker, Front, Right Speaker, Rear, Left
Sie dazu bitte um. Gelb permanente Stromversorgung Rot geschaltete Stromversorgung Lautsprecher vorne rechts Lautsprecher hinten links
Voir le « Schéma de raccordement d’alimentation » au verso pour 4 Jaune alimentation continue 7 Rouge alimentation commutée 3 + Haut-parleur, avant, droit 7 + Haut-parleur, arrière, gauche
plus de détails. Giallo alimentazione continua Rosso alimentazione commutata Grey Diffusore, anteriore, destro Green Diffusore, posteriore, sinistro
Geel continu voeding Rood geschakelde voeding Grau Luidspreker, voor, rechts Grün Luidspreker, achter, links
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
Gris Vert
alimentazione” che si trova sul retro. Blue power aerial control Black earth Speaker, Front, Right Speaker, Rear, Left
Grigio Verde
Zie "Voedingsaansluitschema" op de achterkant voor meer details. Blau Motorantennensteuerung Schwarz Masse Grijs Lautsprecher vorne rechts Groen Lautsprecher hinten links
5 Bleu antenne électrique 8 Noir masse 4 – Haut-parleur, avant, droit 8 – Haut-parleur, arrière, gauche
Blu comando dell’antenna elettrica Nero terra Diffusore, anteriore, destro Diffusore, posteriore, sinistro
Blauw automatische antenne Zwart aarding Luidspreker, voor, rechts Luidspreker, achter, links
Positions 1, 2, 3 and 6 do not have pins. Negative polarity positions 2, 4, 6, and 8 have striped leads.
An Position 1, 2, 3 und 6 befinden sich keine Stifte. An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions 1, 2, 3 et 6 ne comportent pas de broches. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni 1, 2, 3 e 6 non hanno piedini. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities 1, 2, 3 en 6 hebben geen pins. De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
Connection diagram (3) Anschlussdiagramm (3) Schémas de raccordement (3) Schema di collegamento (3) Aansluitschema (3)
A To AMP REMOTE IN of an optional power A An AMP REMOTE IN des gesondert A Au niveau du AMP REMOTE IN d’un A A AMP REMOTE IN di un amplificatore di A Naar AMP REMOTE IN van een optionele
amplifier erhältlichen Endverstärkers amplificateur de puissance facultatif potenza opzionale eindversterker
This connection is only for amplifiers. Connecting any other Dieser Anschluss ist ausschließlich für Verstärker gedacht. Ce raccordement existe seulement pour les amplificateurs. Questo collegamento è riservato esclusivamente agli Deze aansluiting is alleen bedoeld voor versterkers. Door
system may damage the unit. Schließen Sie nichts anderes daran an. Andernfalls kann Le raccordement à tout autre système peut endommager amplificatori. Non collegare un tipo di sistema diverso onde een ander systeem aan te sluiten kan het apparaat worden
B To the interface cable of a car telephone das Gerät beschädigt werden. l’appareil. evitare di causare danni all’apparecchio. beschadigd.
B An Schnittstellenkabel eines Autotelefons B Vers le cordon de liaison d’un téléphone de B Al cavo interfaccia di un telefono per auto B Naar het interface-snoer van een
Warning voiture autotelefoon
If you have a power aerial without a relay box, Warnung Avvertenza
connecting this unit with the supplied power connecting Wenn Sie eine Motorantenne ohne Relaiskästchen Avertissement Quando si collega l’apparecchio con il cavo di Waarschuwing
lead 3 may damage the aerial. verwenden, kann durch Anschließen dieses Geräts mit Si vous disposez d’une antenne électrique sans boîtier alimentazione in dotazione 3, si potrebbe danneggiare Indien u een elektrische antenne heeft zonder relaiskast,
Notes on the control power and suppy leads dem mitgelieferten Stromversorgungskabel 3 die de relais, le branchement de cet appareil au moyen du l’antenna elettrica se questa non dispone di scatola a relè. kan het aansluiten van deze eenheid met het bijgeleverde
• The power aerial control lead (blue) supplies +12 V DC when Antenne beschädigt werden. cordon d’alimentation fourni 3 risque d’endommager Note sui cavi di controllo e di alimentazione netsnoer 3 de antenne beschadigen.
you turn on the tuner, or when you activate the AF (Alternative Steuer- und Stromversorgungsleitungen l’antenne. • Il cavo (blu) di controllo dell’antenna elettrica fornisce Opmerkingen over de bedienings- en voedingskabels
Frequency) or TA (Traffic Announcement) function. • Die Motorantennen-Steuerleitung (blau) liefert +12 V Remarques sur les câbles de commande et de puissance alimentazione pari a +12 V CC quando si attiva il sintonizzatore • De antennevoedingskabel (blauw) levert +12 V gelijkstroom
• When your car has built-in FM/MW/LW aerial in the rear/side Gleichstrom, wenn Sie den Tuner einschalten oder die • Le câble de commande (bleu) fournit du courant continu de oppure la funzione TA (notiziario sul traffico) o AF (frequenza wanneer u de tuner inschakelt of de AF (Alternative
glass, connect the power aerial control lead (blue) or the AF- (Alternativfrequenzsuche) oder die TA-Funktion +12 V lorsque vous mettez le tuner sous tension ou lorsque alternativa). Frequency) of TA (Traffic Announcement) functie activeert.
accessory power input lead (red) to the power terminal of the (Verkehrsdurchsagen) aktivieren. vous activez la fonction AF (fréquence alternative) ou TA • Se l’automobile è dotata di antenna FM/MW/LW incorporata • Wanneer uw auto is uitgerust met een FM/MW/LW-antenne
existing aerial booster. For details, consult your dealer. • Wenn das Fahrzeug mit einer in der Heck-/ (informations circulation). nel vetro posteriore/laterale, collegare il cavo (blu) di in de achterruit/voorruit, moet u de antennevoedingskabel
• A power aerial without a relay box cannot be used with this Seitenfensterscheibe integrierten FM (UKW)/MW/LW- • Lorsque votre voiture est équipée d’une antenne FM/MW controllo dell’antenna elettrica o il cavo (rosso) di ingresso (blauw) of de hulpvoedingskabel (rood) aansluiten op de
unit. Antenne ausgestattet ist, schließen Sie die Motorantennen- (GO)/LW (PO) intégrée dans la vitre arrière/latérale, dell’alimentazione accessoria al terminale di alimentazione voedingsingang van de bestaande antenneversterker.
Memory hold connection Steuerleitung (blau) oder die Zubehörstromversorgungsleitung raccordez le câble de commande d’antenne (bleu) ou del preamplificatore dell’antenna esistente. Per ulteriori Raadpleeg uw dealer voor meer details.
When the yellow power input lead is connected, power will (rot) an den Stromversorgungsanschluss des vorhandenen l’entrée d’alimentation des accessoires (rouge) au bornier informazioni, consultare il proprio fornitore. • Met dit apparaat is het niet mogelijk een automatische antenne
always be supplied to the memory circuit even when the ignition Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem de l’amplificateur d’antenne existant. Pour plus de détails, • Non è possibile usare un’antenna elettrica senza scatola a relè zonder relaiskast te gebruiken.
switch is turned off. Händler. consultez votre revendeur. con questo apparecchio.
Instandhouden van het geheugen
• Es kann nur eine Motorantenne mit Relaiskästchen • Une antenne électrique sans boîtier de relais ne peut pas être Collegamento per la conservazione della memoria Zolang de gele stroomdraad is aangesloten, blijft de
Notes on speaker connection angeschlossen werden.
• Before connecting the speakers, turn the unit off. utilisée avec cet appareil. Quando il cavo di ingresso alimentazione giallo è collegato, viene stroomvoorziening van het geheugen intact, ook wanneer het
• Use speakers with an impedance of 4 to 8 ohms, and with Stromversorgung des Speichers Raccordement pour la conservation de la mémoire sempre fornita alimentazione al circuito di memoria anche quando contact van de auto wordt uitgeschakeld.
adequate power handling capacities to avoid its damage. Wenn die gelbe Stromversorgungsleitung angeschlossen ist, Lorsque le câble de commande d’antenne jaune est connecté, l’interruttore di accensione è spento.
Opmerkingen betreffende het aansluiten van de luidsprekers
• Do not connect the speaker terminals to the car chassis, or wird der Speicher stets (auch bei ausgeschalteter Zündung) mit le circuit de la mémoire est alimenté en permanence même si la Note sul collegamento dei diffusori • Zorg dat het apparaat is uitgeschakeld, alvorens de
connect the terminals of the right speakers with those of the Strom versorgt. clé de contact est en position d’arrêt. • Prima di collegare i diffusori spegnere l’apparecchio. luidsprekers aan te sluiten.
left speaker. Hinweise zum Lautsprecheranschluss Remarques sur le raccordement des haut-parleurs • Usare diffusori di impedenza compresa tra 4 e 8 ohm e con • Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm
• Do not connect the earth lead of this unit to the negative (–) • Schalten Sie das Gerät aus, bevor Sie die Lautsprecher • Avant de raccorder les haut-parleurs, mettre l’appareil hors capacità di potenza adeguata, altrimenti i diffusori potrebbero en let op dat die het vermogen van de versterker kunnen
terminal of the speaker. anschließen. tension. venir danneggiati. verwerken. Als dit wordt verzuimd, kunnen de luidsprekers
• Do not attempt to connect the speakers in parallel. • Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und • Utiliser des haut-parleurs ayant une impédance de 4 • Non collegare i terminali del sistema diffusori al telaio dell’auto ernstig beschadigd raken.
• Connect only passive speakers. Connecting active speakers 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die à 8 ohms et une capacité adéquate sous peine de les e non collegare i terminali del diffusore destro a quelli del • Verbind in geen geval de aansluitingen van de luidsprekers
(with built-in amplifiers) to the speaker terminals may damage Lautsprecher beschädigt werden. endommager. diffusore sinistro. met het chassis van de auto en sluit de aansluitingen van de
the unit. • Verbinden Sie die Lautsprecheranschlüsse nicht mit dem • Ne pas raccorder les bornes du système de haut-parleurs au • Non collegare il cavo di terra di questo apparecchio al terminale rechter- en linkerluidspreker niet op elkaar aan.
• To avoid a malfunction, do not use the built-in speaker leads Wagenchassis und verbinden Sie auch nicht die Anschlüsse châssis de la voiture et ne pas connecter les bornes du haut- negativo (–) del diffusore. • Verbind de aarddraad van dit apparaat niet met de negatieve
installed in your car if the unit shares a common negative (–) des rechten mit denen des linken Lautsprechers. parleur droit à celles du haut-parleur gauche. • Non collegare i diffusori in parallelo. (–) aansluiting van de luidspreker.
lead for the right and left speakers. • Verbinden Sie die Masseleitung dieses Geräts nicht mit dem • Ne pas raccorder le câble de mise à la masse de cet appareil • Assicurarsi di collegare soltanto diffusori passivi, poiché il • Probeer nooit de luidsprekers parallel aan te sluiten.
• Do not connect the unit’s speaker leads to each other. negativen (–) Lautsprecheranschluss. à la borne négative (–) du haut-parleur. collegamento di diffusori attivi, dotati di amplificatori incorporati, • Sluit geen actieve luidsprekers (met ingebouwde versterkers)
Note on connection • Versuchen Sie nicht, Lautsprecher parallel anzuschließen. • Ne pas tenter de raccorder les haut-parleurs en parallèle. ai terminali dei diffusori potrebbe danneggiare l’apparecchio. aan op de luidspreker-aansluiting van dit apparaat. Dit zal
If speaker and amplifier are not connected correctly, “FAILURE” • An die Lautsprecheranschlüsse dieses Geräts dürfen nur • Connectez uniquement des haut-parleurs passifs. La • Per evitare problemi di funzionamento, non utilizzare i cavi dei leiden tot beschadiging van de actieve luidsprekers. Sluit dus
appears in the display. In this case, make sure the speaker and Passivlautsprecher angeschlossen werden. Schließen Sie connexion de haut-parleurs actifs (avec des amplificateurs diffusori incorporati installati nell’automobile se l’apparecchio altijd uitsluitend luidsprekers zonder ingebouwde versterker
amplifier are connected correctly. keine Aktivlautsprecher (Lautsprecher mit eingebauten intégrés) aux bornes des haut-parleurs pourrait endommager condivide un cavo comune negativo (–) per i diffusori destro e aan.
Verstärkern) an, da das Gerät sonst beschädigt werden l’appareil. sinistro. • Om defecten te vermijden mag u de bestaande
könnte. • Pour éviter tout dysfonctionnement, n’utilisez pas les câbles • Non collegare fra loro i cavi dei diffusori dell’apparecchio. luidsprekerbedrading in uw auto niet gebruiken wanneer er een
• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die des haut-parleurs intégrés installés dans votre voiture si Nota sui collegamenti gemeenschappelijke negatieve (–) draad is voor de rechter- en
im Fahrzeug installierten, integrierten Lautsprecherleitungen, l’appareil dispose d’un câble négatif commun (–) pour les Se l’amplificatore e il diffusore non sono collegati correttamente, linkerluidsprekers.
wenn am Ende eine gemeinsame negative (–) Leitung für den haut-parleurs droit et gauche. “FAILURE” viene visualizzato nel display. In tal caso, accertarsi • Verbind de luidsprekerdraden niet met elkaar.
rechten und den linken Lautsprecher verwendet wird. • Ne raccordez pas entre eux les cordons des haut-parleurs de che l’amplificatore e il diffusore siano collegati correttamente. Opmerking over aansluiten
• Verbinden Sie nicht die Lautsprecherkabel des Geräts l’appareil. Als de luidspreker en versterker niet correct zijn aangesloten,
miteinander. wordt "FAILURE" in het display weergegeven. In dit geval moet u
Remarque sur le raccordement
Hinweis zum Anschließen Si les enceintes et l’amplificateur ne sont pas raccordés zorgen dat de luidspreker en versterker correct zijn aangesloten.
Wenn Lautsprecher und Verstärker nicht richtig angeschlossen correctement, le message « FAILURE » s’affiche. Dans ce cas,
sind, erscheint „FAILURE“ im Display. Vergewissern Sie sich assurez-vous que les enceintes et l’amplificateur sont raccordés
in diesem Fall, dass Lautsprecher und Verstärker richtig correctement.
angeschlossen sind.
6
CDX-S2050C/S2050V
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1. SUB PANEL (LCD) ASSY

(Page 8)
2-2. CD MECHANISM BLOCK

(Page 8)
2-3. MAIN BOARD 2-4. CHASSIS (T) SUB ASSY 2-10. SERVO BOARD
(Page 9) (Page 9) (Page 12)
2-5. ROLLER ARM ASSY

(Page 10)
2-6. CHASSIS (OP) ASSY

(Page 10)
2-8. SL MOTOR ASSY (M902)

(Page 11)
2-7. OPTICAL PICK-UP 2-9. LE MOTOR ASSY (M903)

(Page 11) (Page 12)
7
CDX-S2050C/S2050V
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (LCD) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 x 6)
4 sub panel (LCD) assy
2-2. CD MECHANISM BLOCK
7 bracket (CD)
5 CD mechanism block
6 two screws
(+PTT 2.6 x 4)
2 screw 3
(+PTT 2.6 x 6)
1 screw
(+PTT 2.6 x 6)
4 CNP301
8
CDX-S2050C/S2050V
2-3. MAIN BOARD
1 three screws
(+BTT)
2 two screws
(+PTT 2.6 x 8)
3 MAIN board
4 insulating sheet
2-4. CHASSIS (T) SUB ASSY
4 claw
2 two screws
(+P 1.7 x 2.2)
1 two screws
(+P 1.7 x 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
9
CDX-S2050C/S2050V
2-5. ROLLER ARM ASSY
3 washer (1.1-2.5)
5 roller arm assy
4 gear (RA1)
2 spring (RAR)
1 spring (RAL)
2-6. CHASSIS (OP) ASSY
8
qa chassis (OP) assy
0 coil spring (damper)
lever (D)
4 washer
1 CN2 (16P)
6
5 gear (LE1) 9 two coil springs (damper)
slider (R)
3 tension coil spring (KF60)

2 Remove the six solderings.
10
CDX-S2050C/S2050V
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL)
3 screw
(+B 1.4 x 5)
2-8. SL MOTOR ASSY (M902)
1 screw
(+P 1.4 x 1.8)
2 SL motor assy (M902)
11
CDX-S2050C/S2050V
2-9. LE MOTOR ASSY (M903)
0 gear (LE) assy 8 screw

(+M 1.7 x 2.5)
9 bearing (LEB-N)
qa screw 2 washer
qf two toothed lock screws (+M 1.7 x 2.5)
3 gear (LE1)
(+M 1.4 )
lever (D)
4
bracket (LEM-N)
qs screw qg LE motor assy 5
(+M 1.7 x 2.5) (M903)
qd
6 screw
(+P 1.7 x 2.2)
slider (R)
7 leaf spring (LE)
1 Remove the soldering.
2-10. SERVO BOARD
1 Remove the eight solderings. 6 SERVO board
2 Remove the three solderings.
4 toothed lock screw

(M 1.7)
5 claw
3 CN2(16P)
12
CDX-S2050C/S2050V
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM – CD SECTION –
• R-ch is omitted due to same as L-ch.

• Siganal Path
DETECTOR : CD PLAY
PD1
PD1 AGCO 76 EFM 68 MAIN
82 A RFO 78 77 AGCI 71 RFI 69 ASY LOUT 20 CD-L A SECTION
PD2
PD2 ROUT 16 R-CH (Page 14)
84 B
83 C
85 D RF AMP,DIGITAL SERVO,
I-V AMP DIGITAL SIGNAL PROCESSOR LMUTE 30 94 CD_MUTE-L
IC1
RMUTE 29 93 CD_MUTE-R
E
E
87 E FEO 93 92 FE–
F
F
86 F TEO 96 95 TE– TE2 97 98 TEC
SO 12 18 CD_SI
SI 13 19 CD_SO
LASER DIODE SCK 11 20 CD_SCK
AUTOMATIC
LD POWER
1 LD PD 2 RFOK 6 89 CD RFOK
CONTROL
Q1 INTQ 7 55 OP INTQ
PD LD
STB 10 92 CD_STB
A0 9 91 CD_A0
RST 8 90 CD RST
PD
SYSTEM CONTROL
OPTICAL IC501 (1/3)
PICK-UP BLOCK
(KSS1000E) FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING
MOTOR DRIVE
IC2
XTAL 23
2-AXIS DEVICE FCS+ X1
11 VO2– OPIN2+ 5 52 FD+ 16.934MHz
FCS–
12 VO2+ OPIN2– 6 53 FD– XTAL 24
(FOCUS)
(TRACKING)
TRK+ SW1 99 CD_DSW
13 VO1– OPIN1+ 2 54 TD+
(DOWN)
TRK–
14 VO1+ OPIN1– 3 55 TD–
SW2 96 CD_SELFSW
(SELF)
15 VO4+ OPIN4+ 27 56 SD+
M902 M
(SLED) 16 VO4– OPIN4– 26 57 SD– SW3 95 CD_INSW
(DISC IN)
M901 17 VO3+ OPIN3+ 24 58 MD+ SW4 100 CD_LIMIT

(SPINDLE) M (LIMIT)
18 VO3– OPIN3– 23 59 MD–
M903 10 VOL+ FWD 1 97 CD LM LO

(LOADING) M
9 VOL– REV 28 98 CD LM EJ
CDX-S2050C/S2050V
13 13
CDX-S2050C/S2050V
3-2. BLOCK DIAGRAM – MAIN SECTION –
ELECTRONIC VOLUME
IC401
CD
SECTION A CD-L 9 CD LCH
J330
R-CH 8 CD RCH OUT SUB-L 17 L
(Page 13) OUT SUB-R 18 R-CH
AUDIO OUT
R-CH R
POWER AMP,
POWER SUPPLY
TU1 MUTE IC750
(TUNER UNIT) Q481
CN601
J1 1 ANT L-CH 4 7 TU LCH 1
(ANTENNA) OUT FL 23 12 IN FL OUT FL+ 5 FL+
R-CH 3 6 TU RCH 9
OUT FL- 3 FL-
OUT RL 22 11 IN RL
OUT FR 25 R-CH (FRONT) 2
MUTE MUTE OUT RL+ 9 RL+
OUT RR 24 R-CH (REAR) 10
Q441 Q461 OUT RL- 7 RL-
VCC 10 AUDIO+8.3V MUTE 29
4
TU VDD 11 TU+5V SCL FR+
SCL 30 12
E2P VDD 15 BU+3.3V SDA D479 FR-
SDA 31 MUTE DRIVE R-CH 3
BATT RR+
Q478,479 11
RR-
SCL 5
TU-SCL 13 AMP-REM 29 AMP-REM
SDA 6
TU-SDA 14 SYSTEM CONTROL ANT-REM 27 ANT-REM
IC501 (2/3)
FU601
SCL SDA 16
I2C CKO 33 2 SDA BATT
SDA SCL
I2C SIO 34 4 SCL
S-METER 6 39 VSM
VOL ATT 9
TU MUTE 7 12 TU ATT
AUDIO8.3V 30 AUDIO+8.3V
ATT 86 B.UP+B 37
E2P SCL 16 25 EEP CKO BU+3.3V
BEEP 5 16 BEEP SERVO3.3V 31
E2P SDA 17 24 EEP SIO SERVO+3.3V
AMP STB 26 22 STB MECHA6V 33 MECHA+6V
MUTE CONDITION 8 53 TU ATT IN DIAG 8 25 DIAG PANEL+B 34 PANEL+B
QUALITY 5 38 QUALITY
NS MASK 35 VP
BATT
CONTROL 13 NS MASK
Q22
RDS DECODER TEL MUTE 13

IC51 TEL MUTE 74 Q651 TEL-MUTE
SCL
9 XTI SCL 11 ACC CHECK 7
X51 SDA ACC IN 72 Q631 ACC
SDA 12
8.664MHz
10 XTO 15
INTN 15 56 DAVN TEST IN 73 TEST
RDS 9 16 MPX D580,581
BU IN 54 BATTERY CHECK
VDDA VDDD 30 RDS ON BATT
Q580-582
1 7 +5V REG
TU+5V AUDIO+8.3V
Q1
RDS POWER • R-CH is omitted due to same as L-CH.
CONTROL BU+3.3V • Signal Path
Q51
: CD PLAY
: FM
: MW/LW
CDX-S2050C/S2050V
14 14
CDX-S2050C/S2050V
3-3. BLOCK DIAGRAM – DISPLAY SECTION – • Circuit Boards Location
LCD DRIVER
IC901
SYSTEM CONTROL (S2050C)
IC501 (3/3) (S2050V)
KEY MATRIX
41 KEYIN0 SERVO board
4
LSW901-921 S1 | LCD901
40 KEYIN1 LCD SO 28 64 DI
| SENSOR board
LCD CKO 29 50
63 CL
CLK S48 • LIQUID
D501 (1/2) LCD CE 27 62 CE 55 CRYSTAL
COM4 51 DISPLAY
| | PANEL
KEY ACK ON COM1 54
Q664 52 KEY ACK
DIMMER
76 XKEY ON 3 2 1 PANEL+B
LED931,932
D501 (2/2) ( LCDLIGHT
BACK
)
71 RC IN1 LED951,952
J561
(REMOTE IN) 43 RC IN0 LSW901-921
tuner unit
(TU1)
LED COLOR
SELECT
Q991,992
KEY board MAIN board
7 NOSE DET Q921
LED
CONTROL
IR RECEIVER
IC971 S2050C S2050V
RESET (S2050C)
IC602 (S2050V)
BU+3.3V 2 VDD VOUT 1 77 RESET

SIRCS 64 2 OUT IR
S702
RESET
OSC IN 82
79 XOUT X501
X502 18.432MHz
32.678kHz OSC OUT 83
80 XIN
CDX-S2050C/S2050V
15 15
CDX-S2050C/S2050V
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Waveforms
THIS NOTE IS COMMON FOR PRINTED WIRING — MAIN Board — — SERVO Board —
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.) 1 IC51 0 (XTO) 1 IC1 wd (XTAL)
For schematic diagrams. For printed wiring boards.

Note: Note:
1.6Vp-p 1.2Vp-p
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • a : Through hole.
• All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing. 8.664MHz 16.9344MHz
specified. (The other layers' patterns are not indicated.)
• f : internal component.
• C : panel designation. Caution:
Pattern face side: Parts on the pattern face side seen from the
Note: The components identified by mark 0 or dotted line (Side B) pattern face are indicated. 2 IC501 i; (XIN) 2 IC1 uj (AGCI)
with mark 0 are critical for safety. Parts face side: Parts on the parts face side seen from the
Replace only with part number specified. (Side A) parts face are indicated.
• A : B+ Line.
1.4Vp-p 1.6Vp-p
• B : B– Line.
• H : adjustment for repair. C
• Voltages and waveforms are dc with respect to ground Q These are omitted 32.678kHz
under no-signal (detuned) conditions.
• CD mechanism section B E
no mark : CD PLAY
• Main (1/2), (2/2) and Display sections
no mark : FM 3 IC501 id (OSCOUT) 3 IC1 od (FEO)
( ) : MW/LW
< > : CD PLAY
∗ : Impossible to measure
BE C
• Voltages are taken with a VOM (Input impedance 10 MΩ). 1.2Vp-p 0V
Voltage variations may be noted due to normal produc- These are omitted
tion tolerances.
• Waveforms are taken with a oscilloscope. 18.432MHz Approx. 620mVp-p
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms. ECB
• Signal path. These are omitted
J : CD PLAY 4 IC1 oh (TEO)
F : FM
f : MW/LW
0V
Approx. 200mVp-p
CDX-S2050C/S2050V
16 16
CDX-S2050C/S2050V
3-4. PRINTED WIRING BOARDS – SERVO BOARD – • See page 15 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
FMB9
R45
R2
C6
R5
R8
C5
C2
R44
FB2
B
X1
C11
C1
C32
FB3
R41
R42
R10
C31
JR90
C29
R3
JR91
C7
C30
R11
JR41
C36
R13
R4
IC1
C C28
C38
JR40
R1
C13
C27 TP21
Q1
C17
C26
FM
R9 MAIN
B7
FB1
R72
R82
R78
C37
R74
R76
C25 BOARD
C20
R6
R7
CNP301
R14
C23 R15
(Page 19)
C35
C21 R12
C39
CN
D
2
R84
R80
R70
C19
C18
C34
FM
B8
E
R71
C70
CN1
C72 C71
R75 R73
R83 R85
C78 C79
SW3
R81
C77
R79
C76
R77
C73
IC2
F
C75
SW2
C74
1-863-346-
SW1
(DOWN) 1-688-288-
G FMB10
1-863-346-
CDX-S2050C/S2050V
17 17
CDX-S2050C/S2050V
3-5. SCHEMATIC DIAGRAM – SERVO BOARD – • See page 28 for IC Block Diagram. • See page 16 for Waveforms. • See page 30 for IC Pin Descriptions.
C20
TP19 R9 R7 C18
C17
CN2 C25 C23
C19
C21 R6
Q1
TP32 TP33
R14 R15
R13 C36
TP31
C38 TP20
TP30 C37
C39 C26
TP29
TP14 R12 C35 TP21
C27
TP28
TP27
C34 R1
TP26
R11 TP13 C13
IC1 TP12
C28
TP22 TP11
TP10
TP9
C29 TP23
TP8
C30
TP7
TP24 TP6
TP25 TP5
C31 TP4
TP3
SW4
TP2
TP81 C32
TP1
TP80 CN1
FB3 C11
TP65
TP64
JR90
JR91
TP63
TP62
M901 TP85 TP61
TP83 TP60
FB2
C1
R10
TP84 R45 TP59
R2
R3
R4
R5
R8
M902 TP82 C5 X1 R44 TP58
TP57
C6 TP56
FB1
C2 TP55
TP54
C7 TP48
TP27 TP87 R41 TP52
SW3 JR41 TP51
JR40 TP53
TP28 TP88
TP49
(Page 22)
TP29 TP89 R42 TP50
SW2 TP47
TP46
TP45
SW1 TP44
TP90
IC B/D TP43
TP42
TP91
TP41
TP40
R70 R71 C70 IC2 C79 R85 R84
R72 R73 C71 C78 R83 R82
R74 R75 C72 C77 R81 R80
R76 R77 C73 C76 R79 R78
TP100
C74
TP75
TP92
M903
TP93 TP74
TP71
TP70
TP73
TP72
C75
CDX-S2050C/S2050V
18 18
CDX-S2050C/S2050V
3-6. PRINTED WIRING BOARD – MAIN BOARD – • See page 15 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
J330
AUDIO OUT
A J561
(REMOTE IN)
J1
CN601
JC753
JC755
JC754
FB561
C484 C474 C776 C775 C774 JW144
R442 FU601
R472 R432 C751 JW9
R482 C771 C765 C764
JC12
FB562
IC750
Q441
JW3 JW1
Q431
Q471 C763
JC756
JW2
JW13
JW22
JW10
JW14
JW12
JC446 C442
C617
JW11
JW137
JC445
R443 C432 JW15
JW8
JW6
D617
JW7
R431 R433 JW16 C601
C753
Q481 C618
JW143
C R453 C452
JW142
JW17
JW5
D601
R471
D651
Q451
D757
R481 C462 R651
D761
D755
D756
D758
L601
D754
D753
D751
D752
R652
C758
R463 R452
R653 C602
JC1
R451
R462 D609
C471
C623
R654
JW20
D760
D762
D759
C451
Q461
D764
C441 C750 R609 FB563
C769
C761
Q651
R441
C481
D JW110
R461 C461
C759
C770
C760
D763 JW31
C752
C11 C431
JW88 JW32
JW18
TU1 C404 JW92 JW39
JW98
R401
C412
TUNER
JW25
C401
JW24
UNIT JC401 JW111
JW59
JW26
JW102
CNP301
C405 C622 JW113
JW23
R405 Q478
C3
JW42
JW27
C413 JW93
C479 R479 L301
IC401
R406
E R29 JC681 FB304
FB303
R408
C1 Q22 D479
JW132
JW131
C343
R407 JW106
C301
C2 C754 FB302
R409 Q479
R752 C302
R583
C12 R1 R411 FB305 JW115
JW95 C308
C4
C406
C755 FB306
C13 C6 R410 FB301
R302 JW107 D581
JW29
JW91
R582
D1
FB307 (Page 17)
JW94
JW30
JW97
Q580
R2 JW129 C307
C303
FB310
JW73
JW130
FB605 R301 • Semiconductor Location
F
C5
C407
JW66
R3 L1 JW81 D580
JW101
Q1 R531 FB604 FB311 Ref. No. Location Ref. No. Location
R12
JW90
JW150
D1 F-3 D764 D-8

JW72
JC534 JW57
R13 R551
FB1
JW89 D479 E-6
JW118
S2050C R677
C7
R7 R559 JW117
JW99
JW28
R548
R572 R681 D501 I-5 IC51 G-2
JW55
R6 C306
R515
C305
JW109
R516
JW123
JW56
D502 I-7 IC401 E-3
JW50
JW60
C62 R550 R560 R528 R571

R61
JC581
JW100 JW121
R58 R557 R534 S2050V
R573 D580 F-11 IC501 H-6
JC506
JW122 R526
C55 C56 R59 R532 R527 R530 R675 JC536 D581 F-11 IC602 I-9
R631
G R4
R5
IC51 JW80
C756
R537 FMB3
R676
R566
S2050V
R525
R523
R539
D601 C-10 IC750 B-6
C54
R51 C60 X51 JW83 C531 R756 D609 D-8
R8 C53
C59 C511 L501 S2050C R634 D617 C-9 Q1 F-3
R9 R52 C57 R524 R632
R55 C510 R562 R633 D651 C-9 Q22 E-3
JW127
JW34
JW40
R53 C58 R544

JW35
R509
JW38
JW69
JW67
R56 Q631
D701 I-3 Q51 H-3
X501
JW103
JW46
R575
R54 R60
R508 D702 I-3 Q431 B-4
JW52
C631
1
JW79 R57
50
JW51
D719 I-4 Q441 B-4
JW53
IC
JW85 C504
R577
C51
JW78
D751 C-7 Q451 C-4
H JW77
JW84 R570
FB501
C503
C508
R636 R563
JW119
D752 C-7 Q461 D-4
L51 R510 JC505
Q51 D753 C-7 Q471 B-3
JW54
R521 X502
R511 C507
R501 R564 R540 D754 C-7 Q478 E-6
R529 R533
JW44
JW71
R703 JW128 R512 D755 C-6 Q479 E-5

JW70
R680 R541
JW76
R522 C513
JW108
R518 R674 R543

JW133
JC503
D756 C-6 Q481 C-3
JW126
JW74
R502 C512 R561 JW82

C516 C519 R601
JW68
R672 Q582
D757 C-6 Q580 F-11
JW86
D502 R584
C514 R519 JW65 Q581
R707 C501 C509
R504
C502 IC602 R585 D758 C-6 Q581 I-10
I JW139
JW138
JW58
R517 R536
R705
FB603 R567 R673
FB606 D759 D-8 Q582 I-10
JW141
D701 JC504
JW140
R513 R535 D760 D-8 Q631 H-10

JW104
JW63
JW105
JW75
R503 JW62
JW125
D702 JC501
R706
R514 D501 R671
R565 FMB4
Q664 D761 C-9 Q651 D-9
D719 R505
S702 D762 D-9 Q664 I-7
1-864-520- 21 D763 D-8
CN701
J S702
RESET
B1 B2
(S2050C) (S2050V)
(Page 24) (Page 26)

CDX-S2050C/S2050V
19 19
CDX-S2050C/S2050V
3-7. SCHEMATIC DIAGRAM – MAIN BOARD (1/4) – • See page 28 for IC Block Diagram. • See page 16 for Waveforms.
TU1
J330
J1
R12
R13
R2
R3
JC1
JW102
C3 JC12 C484 C474
C2 FB1 R29
C13 C1 R8 C11
C7
R6
Q22
R433 C432
R9
C5 R7 R4
C431 R431 R432
IC401 JC401
JW126
JW77 JW72 Q431

C12 R5
C4 R1 R452
C401
C6 C413
Q451
C451 R451 R453 C452
R405 C412
C404
D1 C405
Q1
C406 R406
L1 C407 R407 C441 R441 R443 C442
L51
JW79 R408
R409 R442
R51 R52 C51 JC446
Q51
Q441
C57 C58 R60
R411
R53 R54
C53
C54
C55
C56
R462
R61
R410 C461 R461 Q461 R463 C462
Q479 (Page 21)

D479 R479
IC51 JC445
IC B/D C481 R481 R482
IC B/D Q481
Q478
R59
JW84 R57
JW85 R56
R472
C62 C479
R55
R401 C471 Q471

X51 R471
R58
C59
C60
(Page 22)
CDX-S2050C/S2050V
20 20
CDX-S2050C/S2050V
3-8. SCHEMATIC DIAGRAM – MAIN BOARD (2/4) – • See page 29 for IC Block Diagram.
C775 C765 C764 C774
C776
C751 D751
IC B/D
C752
D752
C750
D753
D754
JC754
JC755
D755
D756
IC750
D757 CN601
D758
D763
D764
D759
D760
R651
R609
FU601
D651
C753 JC753 C617 C618
C763
D617
(Page 20)
D761
D762
C754
JC756 C758 L601
C602 C601 D601
C769
R752 C755
C770
C760
(Page 23)
CDX-S2050C/S2050V
21 21
CDX-S2050C/S2050V
3-9. SCHEMATIC DIAGRAM – MAIN BOARD (3/4) – • See page 16 for Waveforms. • See page 32 for IC Pin Descriptions.
(Page 20)
JC534 R531
R564 R533 R519 R536 R535
R543
JW86
JW46
R674 C509 JC501
D502
C507 X502
R636 R517
JW125
R680
R518
R672
R529
C508
JC503
R563
Q664
R561
X501
R508
R565 D501
C511
C510
(Page 18) R509
L301 R567 JC504

L501
JC505 R562
FB304 R566
C502 R505 R673
CNP301
R675 R671 C514
R516 R676 (Page 23)
R515 R539 R504
JW55 R524 C512 R503
FB303 IC501
C308 R525 R502
C343 C301 C302 R523 R501
FB305 C303 FB310 R302
FB307 C501 C516
FB306 FB311 R301 JC536 C513
R526
JW107 FB301 C307 R527
R681
R677
FB302
R572 R571 R530
R521 R522
R528 R559 R560
C305 C306
JW34
JW35
JW38
R570
R557
R532
R511
R510
R512
R544
R756 C504
C756
R575
C503
R548 R550
R573
R537
R551
R534 R577 R514 R513

FB501
C531
CDX-S2050C/S2050V
22 22
CDX-S2050C/S2050V
3-10. SCHEMATIC DIAGRAM – MAIN BOARD (4/4) –
(Page 21)
C759 CN701
FB603
R705 (Page 25)

R706
FB604 JC681 R707
C771
IC602 C623
(Page 27)
FB606
C761
R601 JW98
(Page 22) S702
C519 C622
JC506 FB605
D701 D702
R652
R703
JW53
R633 R631 R653
R541 Q631 Q651
FB563
R634 C631 R632 R654
D609 D719 FB562 J561
R540
FB561
R585
JC581
R584 Q581
Q582 D580 R582
Q580
D581 R583
CDX-S2050C/S2050V
23 23
CDX-S2050C/S2050V
3-11. PRINTED WIRING BOARD – KEY BOARD (S2050C) – • See page 15 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A LSW905 LSW906 LSW901

LED951 R923 LSW910
LED952
(DISC-L) (DISC-R) LSW901
LSW905 LSW910,
R924
LSW906 R933 LED941
R955
R960 R957
R921 R922
B R956
R929
R958 R973 LED941
R959
(LCD BACK LIGHT)

R952 R951 R909
R927
R953 R930
LED932
LED931
VOL LCD901 R928
R954 R931
R908
(LCD BACK LIGHT)
LIQUID CRYSTAL DISPLAY PANEL R925 SEEK
LSW903 LSW907 LSW908 R907 LSW909 R926

C SOURCE MODE ATT EQ3 LED942
LSW904 LSW911,
LSW904 LED942
50 20 LSW911
52 40 30 10 1
R910
JP935
IC971
R949 R950 R944 R943 R940 R939 R936 R938 R935 JP936 R937
D 1-864-521- 11
LSW921 LSW920 LSW919 LSW918 LSW917 LSW916 LSW915 LSW914 LSW913 LSW912 LSW902 IC971
DSPL/DIM SENS/BTM 1 2 3/REP 4/SHUF 5 6 PTY AF/TA OFF
(Page 19)
MAIN
E B1 BOARD
CN701
R918 R916 R914

R917
R941
R912
R911
CN901
R919
R913
R947 R948 R946 R945 R915 R942
F FMB3
C971
R904
R974
R972
R903
R967 R977 R961 R901
R976
D902
G Q991
R981
IC901
R979 R978
D901 R902
Q921 Q992 R983
C982
R932
R905
R962 JP961
C981
R963
C986
C985
R906
D981
D982
R987
R982
R985
R984
C984
C983
R986
FMB4
R934
H
1-864-521- 11
• Semiconductor Location
Ref. No. Location Ref. No. Location
D901 G-11 LED932 C-4
D902 G-11 LED941 B-14
D981 G-6 LED942 C-14
D982 G-10 LED951 A-12
LED952 A-3
IC901 G-8
IC971 D-14 Q921 G-4
Q991 G-5
LED931 C-12 Q992 G-5
CDX-S2050C/S2050V
24 24
CDX-S2050C/S2050V
3-12. SCHEMATIC DIAGRAM – KEY BOARD (S2050C) –
JP935 R981
LED951 LED952
LSW909(2/2) LSW914(2/2) LSW904(2/2)
D902
R982 R972
CN901 LED941 R973
LED931
LSW902(2/2) LSW917(2/2)
LSW907(2/2) R955 R958 IC971
R939
JP961
R921 R923 R929 R937 R945 R949 R956 R959
R931 R935 R940 R943
R922 R924 R930 R946 R957 R960 C971
JP936 LSW921(2/2)
R974 R925 R927 LSW915(2/2)
R961 R951 R953
LSW912(2/2)
R926 R928
(Page 23) R962 R941 R947 R952 R954
R976
R950
LSW901(2/2) LSW908(2/2)
R963 R942 R948
R983
LED942 R932 R936 R938

C982 R984
LED932 LSW918(2/2) LSW903(2/2) C983 IC901
D901 D982 C984 R985
R986
LSW910(2/2) LSW916(2/2) LSW920(2/2) LSW905(2/2) C981
D981
R933 R934 R987
R944
R977
C985 C986
LSW913(2/2) LSW919(2/2) LSW906(2/2) R978
LSW911(2/2) R979
Q921
R967
Q992 Q991
R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
LSW912(1/2)
LSW913(1/2)
LSW914(1/2)
LSW915(1/2)
LSW916(1/2)
LSW917(1/2)
LSW918(1/2)
LSW919(1/2)
LSW920(1/2)
LSW921(1/2)
LCD901
R901 R902 R903 R904 R905 R906

LSW901(1/2)
LSW902(1/2)
LSW903(1/2)
LSW904(1/2)
LSW905(1/2)
LSW906(1/2)
LSW907(1/2)
CDX-S2050C/S2050V
25 25
CDX-S2050C/S2050V
3-13. PRINTED WIRING BOARD – KEY BOARD (S2050V) – • See page 15 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A LSW905
LED952 LSW901
LED952 LSW910
(DISC-L) LED951
LSW905 LSW901
(DISC-R) LED951 LSW910,
LSW906 R933 LED941
LSW906
R921
R955
R957
R922
B R956
R973
R952 R951 R909 LED941
LED932 LED931
R929
(LCD BACK LIGHT) (LCD BACK LIGHT) R930
VOL LCD901
R908
LIQUID CRYSTAL DISPLAY PANEL R925 SEEK
LSW903 LSW907 LSW908 R907 LSW909 R926

C SOURCE MODE ATT
EQ3
LSW904 LED942 LSW911,
LSW904 LED942
50 20
52 40 30 10 1
R910
JP935
IC971
R944 R943 R940 R939 R936 R935
LSW911
D
LSW921 LSW920 LSW919 LSW918 LSW917 LSW916 LSW915 LSW914 LSW913 LSW912 LSW902 IC971
DSPL/DIM SENS/BTM 1 2 3/REP 4/SHUF 5 6 PTY AF/TA OFF
(Page 19)
MAIN
E B2 BOARD
CN701
R918 R916 R914

R917
R912
R919
R911
R913
R947 R948 R915
F FMB3
C971
R904
R974
R972
R903
D902
R967 R977 R961 R901
R978
R976
R979
G
Q921
R981 IC901 R90 2

D901
R983
R905
R963 R962 JP961

C981
R906
C986
C985
R987
D981
R982
D982
R984
C982
R986
C984
C983
R985
FMB4
• Semiconductor Location
Ref. No. Location Ref. No. Location
D901 G-11 LED931 B-11
D902 G-11 LED932 B-4
D981 G-6 LED941 B-14
D982 G-10 LED942 C-14
LED951 A-12
IC901 G-8 LED952 A-2
IC971 D-14
Q921 G-4
CDX-S2050C/S2050V
26 26
CDX-S2050C/S2050V
3-14. SCHEMATIC DIAGRAM – KEY BOARD (S2050V) –
JP935 R981
LED951 LED952
LSW909(2/2) LSW914(2/2) LSW904(2/2)
D902
R982 R972
CN901 LED941 R973
LED931
LSW902(2/2) LSW917(2/2)
LSW907(2/2) R955 IC971
R939
JP961
R921 R929 R956
R935 R940 R943
R922 R930 R957 C971
LSW921(2/2)
R925
R974 LSW915(2/2)
R961
LSW912(2/2)
R926
R947 R951
(Page 23) R962
R976
LSW901(2/2) LSW908(2/2) R948 R952
R963
R983
LED942 R936
LED932 LSW918(2/2) LSW903(2/2) C982 C983 R984 IC901
D901 D982 C984 R985
R986
LSW910(2/2) LSW916(2/2) LSW920(2/2) LSW905(2/2) C981
D981
R933 R987
R944
R977
C985 C986
LSW913(2/2) LSW919(2/2) LSW906(2/2) R978
LSW911(2/2) R979
Q921
R967
R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
LSW912(1/2)
LSW913(1/2)
LSW914(1/2)
LSW915(1/2)
LSW916(1/2)
LSW917(1/2)
LSW918(1/2)
LSW919(1/2)
LSW920(1/2)
LSW921(1/2)
LCD901
R901 R902 R903 R904 R905 R906

LSW901(1/2)
LSW902(1/2)
LSW903(1/2)
LSW904(1/2)
LSW905(1/2)
LSW906(1/2)
LSW907(1/2)
CDX-S2050C/S2050V
27 27
CDX-S2050C/S2050V
• IC Block Diagrams
– SERVO Board – – MAIN Board –
IC2 BA5966FP-FE2 IC401 BD3808FS-FE2

OPIN4(+)
OPIN4(–)
OPIN3(+)
OPIN3(–)
OPOUT4
OPOUT3
OUTR1
OUTR2
OUTS1
OUTS2
OUTF1
OUTF2
VO3(–)
VO3(+)
VO4(–)
VO4(+)
DGND
MUTE
MUTE
SDA
VCC
BIAS
SCL
ADJ
SEL
GND
REV
NC
NC
NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
VCC
+ – + – MUTE
– + + – – + + –
FADER FADER FADER FADER

I2C BUS (0~-58, (0~-58, (0~-58, (0~-58,
– – + VCO -∞dB) -∞dB) -∞dB) -∞dB)
LEVEL LOGIC GAIN+ATT
+ SHIFT – + (+10~-29,
–
LEVEL -∞dB)
LOADING DRIVER EFFECT (0dB~ EFFECT (0dB~ 2ND ORDER LPF
+ SHIFT
+20dB,2dB STEP) +20dB,2dB STEP) fc:OFF,80,120,160Hz
REV OUT F 2ND ORDER
Q: 0.707
LPF
FWD OUT R BASS MIX
+ LEVEL fo:60,70,80,100,120,140,160,200Hz
– SHIFT TONE TONE
+ – + Q:0.5,0.75,1,1.25
LEVEL PASS PASS
– SHIFT
– +
MIDDLE BASS,TREBLE, MIDDLE BASS,TREBLE, MIDDLE
fo:500Hz,1kHz (-15dB~+15dB,1dB STEP) (-15dB~+15dB,1dB STEP)
Q:1
– + + – – + + –
+ – + – VOLUME VOLUME
VCC TABLE (+23~-79dB,-∞dB (+23~-79dB,-∞dB
fo:5,7.5,10,12.5kHz 1dB STEP) 1dB STEP)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
FWD
OPIN1(+)
OPIN1(–)
OPOUT1
OPIN2(+)
OPIN2(–)
OPOUT2
VCC
VOL(–)
VOL(+)
VO2(–)
VO2(+)
VO1(–)
VO1(+)
fc:40kHz fc:40kHz
ANTI-ALIASING ANTI-ALIASING
FILTER FILTER
INPUT GAIN INPUT GAIN

(0~15dB,1dB STEP) (0~15dB,1dB STEP)
MUTE MUTE
INPUT SELECTOR
(4 STEREO INCLUDE 1 ISOLATION INPUT)
VCC/2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
AGND
FIL
AP1
AN
AP2
B1
B2
C1
C2
NC
NC
NC
NC
NC
NC
NC
IC51 TDA7333013TR
INTERPOLATOR BAND PASS SINC4 SIGMA DELTA

16 MPX
FILTER FILTER CONVERTER
VDDA 1
SINC4REG
15 INTN
MPX
REF3 2
REF2 3 SDAOUT
RAM SDAIN 14 CSN
RDS RDSREG BUFFER 2 TEST LOGIC
REF1 4 INTN DEMODULATOR & I C/SPI SCK 13 SA_DATAOUT
& &
SYNCHRONIZATION INTERFACE SPI 12 SDA_DATAIN
CONTROL PIN MUX'S
TESTREG 11 SCL_CLK
LOGIC
VSS 5
TM 6 2
10 XTO
OSCILLATOR
VDDD 7 9 XTI
RESETN 8
CDX-S2050C/S2050V
28 28
CDX-S2050C/S2050V
IC750 TDA8588BJ/N2/R1
TAB 1
2 SDA
OUT-FL- 3 I2C BUS
4 SCL
FL
OUT-FL+ 5
6 VP2
OUT-RL- 7
RL 8 PGND3
OUT-RL+ 9
10 SVR
IN-RL 11
MUTE
12 IN-FL
S-GND 13
PROTECTION/
DIAGNOSTIC 14 IN-FR
MUTE
IN-RR 15
16 BEEP
VP
OUT-RR+ 17
RR 18 PGND2
OUT-RR- 19
20 VP1
OUT-FR+ 21
STANDBY/
FR MUTE 22 STB
OUT-FR- 23
CHIP DETECT/
DIAGNOSTIC 24 PGND1
BATTERY TEMPERATURE
DIAG 25 DETECTION PROTECTION ENABLE
LOGIC
26 RST
ANT-REM 27 SWITCH
28 CRES
AMP-REM 29 SWITCH
30 AUDIO8.3V
REGULATOR
SERVO5V 31
32 GND
MECH6V 33
34 PANEL+B
VP 35
REFERENCE 36 CBU
VOLTAGE
LOADDUMP BACK-UP
B.UP+B 37 REGULATOR PROTECTION SWITCH
29
CDX-S2050C/S2050V
• IC Pin Descriptions
IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No. Pin Name I/O Pin Description

1 LD O Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
2 PD I Dimmer monitor input from optical pick-up laser diode.
3 PN I Not used. (Fixed at L in this set)
4 AVDD — Analog power supply pin (+3.3 V)
5 DGND — Ground
6 RFOK O RFOK signal output to system control IC.
7 INTQ O CD text pack synchronization signal output to system control IC.
8 RST I CD reset signal input from system control IC.
Command/parameter discrimination signal input from system control IC.
9 A0 I
(L: command transmission, H: parameter transmission)
10 STB I Data strobe signal input from system control IC.
11 SCK I Serial clock input from system control IC.
12 SO O Serial data output to system control IC.
13 SI I Serial data input from system control IC.
14 DVDD — Power supply pin (+3.3 V)
15 DAVDD — D/A converter power supply (+) pin (+3.3 V)
16 ROUT O Analog audio signal output (R-ch)
17 DAGND — Ground
18 REGC — Capacitor connection pin for SCF regulator.
19 DAGND — Ground
20 LOUT O Analog audio signal output (L-ch)
21 DAVDD — D/A converter power supply (+) pin (+3.3 V)
22 XVDD — Power supply pin (+3.3 V)
23 XTAL O Main system clock output (16.9344 MHz)
24 XTAL I Main system clock input (16.9344 MHz)
25 XGND — Ground
27 C1D1/FZD O Not used. (Open)
28 C1D2/TZD O Not used. (Open)
29 C2D1/RMUTE O CD R-ch data zero detection signal output
30 C2D2/LMUTE O CD L-ch data zero detection signal output
31 C2D3/SHOCK/SBSY O Not used. (Open)
32 LOCK/FR O Not used. (Open)
33 WFCK/MIRR O Not used. (Open)
34 RFCK/HOLD O Not used. (Open)
35 PLCK O Not used. (Open)
36 C16M O Not used. (Open)
37 DGND — Ground
38 TX O Not used. (Open)
39 EMPH/RAMOVER O Not used. (Open)
40 FLAG O Not used. (Open)
42 LIMIT I Not used. (Fixed at L in this set)
Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
43 XTALEN I
(Fixed at L in this set)
44 DGND — Ground
45 DIN I Not used. (Connect to DOUT in this set)
46 DOUT O Not used. (Connect to DIN in this set)
47 SCKIN I Not used. (Connect to SCKO in this set)
48 SCKO O Not used. (Connect to SCKIN in this set)
49 LRCKIN I Not used. (Connect to LRCK in this set)
30
CDX-S2050C/S2050V

50 LRCK O Not used. (Connect to LRCKIN in this set)
52 FD+ O Focus servo drive PWM signal output (+)
53 FD– O Focus servo drive PWM signal output (–)
54 TD+ O Tracking servo drive PWM signal output (+)
55 TD– O Tracking servo drive PWM signal output (–)
56 SD+ O Sled servo drive PWM signal output (+)
57 SD– O Sled servo drive PWM signal output (–)
58 MD+ O Spindle servo drive PWM signal output (+)
59 MD– O Spindle servo drive PWM signal output (–)
60 DGND — Ground
61 TESTEN I Test setting input (Fixed at L in this set)
62 to 66 TEST4 to TEST0 I Test setting input (Fixed at L in this set)
67 ADGND — A/D converter power supply (–) pin
68 EFM O EFM signal output
69 ASY I EFM comparator reference voltage input
70 ADVDD — A/D converter power supply pin (+3.3 V)
71 RFI I RF signal input for EFM data growing.
72 EQ2 — Not used. (Open)
73 EQ1 — RF amplifier equalizer parts connection pin
74 RF– I Not used. (Open)
75 RF2– I RF amplifier inversion input
76 AGCO O RF signal output after on AGC.
77 AGCI I RF AGC signal amplifier input
78 RFO O RF signal output before on AGC.
79 ATEST I Not used. (Open)
80 C3T — Capacitor connection pin for 3T detection.
81 AGND — Ground
82 A I Signal input (A) from optical pick-up detector.
83 C I Signal input (C) from optical pick-up detector.
84 B I Signal input (B) from optical pick-up detector.
85 D I Signal input (D) from optical pick-up detector.
86 F I Signal input (F) from optical pick-up detector.
87 E I Signal input (E) from optical pick-up detector.
88 VREFIN I Reference voltage (+1.65 V) input
89 AVDD — Analog power supply pin (+3.3 V)
90 REFOUT O Reference voltage (+1.65 V) output
91 REFC — Capacitor connection pin for reference voltage output.
92 FE– I Focus error signal amplifier inversion input
93 FEO O Focus error signal amplifier output
94 ADCIN I Not used. (Open)
95 TE- I Tracking error signal amplifier inversion input
96 TEO O Tracking error signal amplifier before output
97 TE2 O Tracking error signal amplifier after output
98 TEC I Tracking error signal comparator input
99 AGND — Ground
100 PWMSW I Not used. (Fixed at L in this set)
31
CDX-S2050C/S2050V
IC501 MB90488BPF-G-117-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (3/4))

1 AREA SEL2 I Destination setting pin
4 COL SW I Illumination color select signal input
5 BEEP O Beep signal output
6 NCO O Not used
7 NOSE SW I Front panel open/close detect signal input
8 DIAG I Power AMP status signal input
9 VOL ATT O Electronic volume attenuate control signal output
10 NCO O Not used
11 VSS — Ground
12 TU ATT O Tuner mute control signal output
13 NS MASK O Noise mask signal output
14 ILLUMI SEL1 I Illumination voltage setting pin
15 ILLUMI SEL2 I Illumination voltage setting pin
16 NCO O Not used
17 NCO O Not used
18 CD SI I CD servo IC serial data input
19 CD SO O CD servo IC serial data output
20 CD SCK O CD servo IC serial clock output
21 NCO O Not used
22 NCO O Not used
23 VCC5 — Power supply pin (+3.3V)
24 EEP SIO I/O EEPROM bus serial data input/output
25 EEP CKO O EEPROM bus serial clock output
26 AMP STB O Power AMP satandby signal output
27 LCD CE O LCD driver chip enable output
28 LCD SO O LCD driver serial data output
29 LCD SCK O LCD driver serial clock output
30 RDS ON O RDS ON signal output
31 NCO O Not used
32 NCO O Not used
33 I2C SCK O I2C bus serial clock output
34 I2C SIO I/O I2C bus serial data input/output
35 DAVDD — A/D converter power supply pin (+3.3V)
36 AVRH — A/D converter reference power supply pin (+3.3V)
37 DAVSS — Ground
38 QUALITY I Noise detect signal input
39 VSM I S-meter voltage detect signal input
40 KEY IN1 I Key signal input
41 KEY IN0 I Key signal input
42 VSS — Ground
43 RC IN0 I Rotary commander key signal input
44 NCO O Not used
45 NCO O Not used
46 NCO O Not used
47 NCO O Not used
48 NCO O Not used
49 MD0 I Operation mode setting pin
32
CDX-S2050C/S2050V

52 KEY ACK I Key acknowledgment detect signal input
53 TU ATT IN I Tuner mute zero cross detect signal input
54 BU IN I Back-up power supply detect signal input
55 CD INTQ I CD text pack synchronized signal input
56 DAVN I RDS data block synchronized detect signal input
57 NCO O Not used
58 UNI SI I SONY bus data input
59 UNI SO O SONY bus data output
60 UNI SCK O SONY bus clock output
61 NCO O Not used
62 NCO O Not used
63 NCO O Not used
64 SIRCS I Remote control signal input
65 NCO O Not used
66 NCO O Not used
67 NCO O Not used
68 FLASH W I Memory mode select signal input
69 NCO O Not used
70 NCO O Not used
71 RC IN1 I Rotary commander shift key signal input
72 ACC IN I Accessory power supply detect signal input
73 TEST IN I Test mode detect signal input
74 TEL ATT I Telephone attenuate detect signal input
75 NCO O Not used
76 XKEY ON O A/D converter power supply control signal output
77 RESET I CPU reset input
78 NCO O Not used
79 XOUT — Sub-clock output (32.768kHz)
80 XIN — Sub-clock input (32.768kHz)
81 VSS1 — Ground
82 OSC IN — Main-clock input (3.68MHz)
83 OSC OUT — Main-clock output (3.68MHz)
84 VCC3 — Power supply pin (+3.3V)
85 DEMO SEL I Demo select signal input
86 ATT O Audio mute control signal output
87 BUS ON O Bus ON signal output
88 SYS RST O System reset output
89 CD RFOK I CD shutter-open information signal input
90 CD RST O CD servo reset output
91 CD A0 O CD servo command/parameter signal output
92 CD STB O CD servo daata strobe signal output
93 CD MUTE R I CD zero cross mute detect signal input (Rch)
94 CD MUTE L I CD zero cross mute detect signal input (Lch)
95 CD IN SW I CD disc-in switch detect signal input
96 CD SELF SW I CD self switch signal input
97 CD LM LO O CD loading motor control signal output
98 CD LM EJ O CD eject motor control signal output
99 CD D SW I CD D-switch detect signal input
100 CD LIMIT I CD limit switch detect signal input
33
CDX-S2050C/S2050V
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark 0 or dotted line with mark
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) 0 are critical for safety.
they are seldom required for routine service. R R Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories are given in the last of this parts list.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
4-1. MAIN SECTION

A
MG-611XE-186//K #2
#1
not supplied
B
6
A
FU601
5 #3
4
7
3 8
#1
TU1
not supplied
2
#1
not supplied
#1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2023-967-1 PANEL (LCD) ASSY, SUB 8 A-1082-337-A MAIN BOARD, COMPLETE (S2050V)
2 2-583-939-01 SCREW (+B 2X4) 8 A-1083-043-A MAIN BOARD, COMPLETE (S2050C)
3 X-2024-365-1 LOCK ASSY (S) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
4 3-246-006-31 COVER TU1 A-3220-961-A TUNER UNIT (TUX-032)
5 2-583-940-01 SCREW (+BTT) #1 7-685-792-09 SCREW +PTT 2.6X6 (S)
6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER) #2 7-685-790-01 SCREW +PTT 2.6X4 (S)
7 2-345-298-01 PLATE (TU), GROUND #3 7-685-793-09 SCREW +PTT 2.6X8 (S)
34
CDX-S2050C/S2050V
4-2. FRONT PANEL SECTION
61
60
LCD901
56 61
not supplied
58
59
57
not supplied
(DISPLAY board)
not supplied
51
54
53
55
not supplied
55
62 not supplied
not supplied
52
not supplied
51 X-2024-366-3 BUTTON ASSY (S) 58 2-187-728-02 PANEL, FRONT BACK
52 2-187-736-01 FILTER (IR) 59 X-2024-133-2 CASE ASSY (for FRONT PANEL)
53 2-187-738-01 SPRING (RELEASE) 60 A-1083-034-A PANEL COMPLETE ASSY, FRONT (S2050V)
54 X-2048-521-2 PANEL SUB ASSY, FRONT (S2050V) 60 A-1083-045-A PANEL COMPLETE ASSY, FRONT (S2050C)
54 X-2048-522-2 PANEL SUB ASSY, FRONT (S2050C) 61 3-250-543-31 SCREW (+B P-TITE M2)
55 2-187-737-01 PLATE (CD), LIGHT GUIDE 62 3-251-320-01 EMBLEM (NO. 2.5), SONY
56 1-780-199-11 CONDUCTIVE BOARD, CONNECTION LCD901 1-805-728-11 DISPLAY PANEL, LIQUID CRYSTAL (S2050C)
57 X-2023-711-1 HOLDER (LCD) ASSY LCD901 1-805-729-11 DISPLAY PANEL, LIQUID CRYSTAL (S2050V)
35
CDX-S2050C/S2050V
4-3. CD MECHANISM SECTION (1)

(MG-611XE-186//K)
not supplied
102 (SENSOR board)
101
not supplied
#4
not supplied
not supplied
not supplied
103
104
106
105
108
107
101 A-3372-455-A CHASSIS (T) SUB ASSY 106 3-253-748-01 DAMPER (S)
102 3-253-729-01 SPRING (LTR), TENSION COIL 107 3-352-758-31 SCREW (M1.7), TOOTHED LOCK
103 3-253-746-14 SPRING (DAMPER), COMPRESSION 108 A-1082-670-A SERVO BOARD, COMPLETE
104 3-253-746-03 SPRING (DAMPER), COMPRESSION #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
105 2-345-767-01 SPRING (KF60), TENSION
36
CDX-S2050C/S2050V

(MG-611XE-186//K)
155
156
157
154
(including M901)
#5
M902
SW4
not supplied
not supplied
158
153
not supplied
not supplied
152
151
The components identified by

mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
151 A-1075-786-A CHASSIS (OP) COMPLETE ASSY 157 X-3383-454-3 LEVER (SL) ASSY
152 3-316-938-91 SCREW (B1.4X5), TAPPING 158 3-261-959-02 SPRING (SL), TORSION
0 153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP) M902 A-3337-638-A MOTOR ASSY, SL (SLED)
154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
155 A-3337-641-A ARM SUB ASSY, CHUCKING #5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8
156 A-3337-639-A LEVER (SL) SUB ASSY
37
CDX-S2050C/S2050V

(MG-611XE-186//K)
201 203
202
207
211
204
209
208 210 205
207
207
M903
#4
206
201 3-262-755-01 WASHER (1.1-2.5) 208 2-186-696-11 BRACKET (LEM-N)
202 2-186-699-11 GEAR (RA1) 209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK
203 A-1075-789-A ARM ASSY, ROLLER 210 A-1083-637-A GEAR (LE) ASSY
204 3-259-455-02 SPRING (RAL) 211 2-186-697-11 BEARING (LEB-N)
205 3-253-713-01 SPRING (RAR) M903 A-1075-792-A MOTOR ASSY, LE (LOADING)
206 3-259-469-01 SPRING (LE), LEAF #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

207 2-134-636-31 SCREW (M1.7X2.5)
38
CDX-S2050C/S2050V

(MG-611XE-186//K)
254
252
255
252
256
251 253
257
251 2-186-700-11 GEAR (CHK1) 255 3-899-829-01 WASHER (SLIT)
252 3-344-223-01 WASHER 256 3-259-032-01 GEAR (LE2)
253 3-259-470-01 GEAR (LE1) 257 A-1075-791-A CHASSIS (M) BLOCK ASSY
254 3-253-755-02 LEVER (D)
39
CDX-S2050C/S2050V
SECTION 5
KEY (S2050C)
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. When indicating parts by reference
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. number, please include the board.
All resistors are in ohms. • CAPACITORS
METAL:Metal-film resistor. uF : µF
METAL OXIDE: Metal oxide-film resistor. • COILS
F:nonflammable uH : µH
KEY BOARD (S2050C) < SWITCH >
**********
LSW901 1-786-808-11 SWITCH, TACTILE (WITH LED) (Z)
1-780-199-11 CONDUCTIVE BOARD, CONNECTION LSW902 1-786-808-11 SWITCH, TACTILE (WITH LED) (OFF)
LSW903 1-786-808-11 SWITCH, TACTILE (WITH LED) (SOURCE)
< CAPACITOR > LSW904 1-786-803-11 SWITCH, TACTILE (WITH LED) (VOL –)
LSW905 1-786-808-11 SWITCH, TACTILE (WITH LED) (SEL)
C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C981 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V LSW906 1-786-803-11 SWITCH, TACTILE (WITH LED) (VOL +)
C982 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V LSW907 1-786-808-11 SWITCH, TACTILE (WITH LED) (MODE)
C983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LSW908 1-786-808-11 SWITCH, TACTILE (WITH LED) (ATT)
C984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LSW909 1-786-808-11 SWITCH, TACTILE (WITH LED) (EQ3)
LSW910 1-786-803-11 SWITCH, TACTILE (WITH LED)
C985 1-131-664-11 CERAMIC CHIP 0.15uF 10% 10V (SEEK +/> M)
< CONNECTOR > (SEEK –/m .)
LSW912 1-786-808-11 SWITCH, TACTILE (WITH LED) (AF/TA)
CN901 1-794-312-11 PIN, CONNECTOR 12P LSW913 1-786-808-11 SWITCH, TACTILE (WITH LED) (PTY)
LSW914 1-786-808-11 SWITCH, TACTILE (WITH LED) (6)
< DIODE > LSW915 1-786-808-11 SWITCH, TACTILE (WITH LED) (5)
D901 6-500-886-01 DIODE RSA6.1ENTR LSW916 1-786-808-11 SWITCH, TACTILE (WITH LED) (4/SHUF)
D902 8-719-083-66 DIODE UDZSTE-1718B LSW917 1-786-808-11 SWITCH, TACTILE (WITH LED) (3/REP)
D981 8-719-069-54 DIODE UDZSTE-175.1B LSW918 1-786-808-11 SWITCH, TACTILE (WITH LED) (2)
D982 8-719-988-61 DIODE 1SS355TE-17 LSW919 1-786-808-11 SWITCH, TACTILE (WITH LED) (1)
LSW920 1-786-808-11 SWITCH, TACTILE (WITH LED) (SENS/BTM)
< IC >
LSW921 1-786-808-11 SWITCH, TACTILE (WITH LED) (DSPL/DIM)
IC901 6-707-063-01 IC LC75826WH-US-E
IC971 6-600-163-01 IC RS-770 ( ) < TRANSISTOR >
< JUMPER RESISTOR > Q921 8-729-027-58 TRANSISTOR DTC143ZKA-T146

Q991 6-550-752-01 TRANSISTOR DTC614TKT146
JP935 1-216-864-11 SHORT CHIP 0 Q992 6-550-752-01 TRANSISTOR DTC614TKT146
JP936 1-216-864-11 SHORT CHIP 0
JP961 1-216-864-11 SHORT CHIP 0 < RESISTOR >
< LIQUID CRYSTAL DISPLAY > R901 1-216-819-11 METAL CHIP 680 5% 1/10W
R902 1-216-819-11 METAL CHIP 680 5% 1/10W
LCD901 1-805-728-11 DISPLAY PANEL, LIQUID CRYSTAL R903 1-216-819-11 METAL CHIP 680 5% 1/10W
R904 1-216-821-11 METAL CHIP 1K 5% 1/10W
< DIODE > R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
LED931 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT) R906 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
LED932 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT) R907 1-216-819-11 METAL CHIP 680 5% 1/10W
LED941 6-500-509-01 LED CL-165D/PG-D-T (> M) R908 1-216-819-11 METAL CHIP 680 5% 1/10W
LED942 6-500-509-01 LED CL-165D/PG-D-T (. m) R909 1-216-819-11 METAL CHIP 680 5% 1/10W
LED951 6-500-509-01 LED CL-165D/PG-D-T (DISC-R ILLUMI) R910 1-216-821-11 METAL CHIP 1K 5% 1/10W
LED952 6-500-509-01 LED CL-165D/PG-D-T (DISC-L ILLUMI) R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R912 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
40
CDX-S2050C/S2050V
KEY (S2050C) KEY (S2050V)
R914 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R982 1-216-811-11 METAL CHIP 150 5% 1/10W
R915 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R983 1-216-864-11 SHORT CHIP 0
R916 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R984 1-216-821-11 METAL CHIP 1K 5% 1/10W
R917 1-216-833-11 METAL CHIP 10K 5% 1/10W R985 1-216-821-11 METAL CHIP 1K 5% 1/10W
R919 1-216-837-11 METAL CHIP 22K 5% 1/10W R987 1-216-857-11 METAL CHIP 1M 5% 1/10W
R921 1-216-813-11 METAL CHIP 220 5% 1/10W *************************************************************
R922 1-216-813-11 METAL CHIP 220 5% 1/10W
R923 1-216-811-11 METAL CHIP 150 5% 1/10W KEY BOARD (S2050V)
R924 1-216-811-11 METAL CHIP 150 5% 1/10W **********
R925 1-216-809-11 METAL CHIP 100 5% 1/10W 1-780-199-11 CONDUCTIVE BOARD, CONNECTION
R926 1-216-805-11 METAL CHIP 47 5% 1/10W
R927 1-216-807-11 METAL CHIP 68 5% 1/10W < CAPACITOR >
R928 1-216-807-11 METAL CHIP 68 5% 1/10W
R929 1-216-809-11 METAL CHIP 100 5% 1/10W C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R933 1-216-811-11 METAL CHIP 150 5% 1/10W
R935 1-216-809-11 METAL CHIP 100 5% 1/10W
R936 1-216-805-11 METAL CHIP 47 5% 1/10W < CONNECTOR >
R937 1-216-807-11 METAL CHIP 68 5% 1/10W
R938 1-216-805-11 METAL CHIP 47 5% 1/10W CN901 1-794-312-11 PIN, CONNECTOR 12P
R939 1-216-809-11 METAL CHIP 100 5% 1/10W
< DIODE >
R940 1-216-805-11 METAL CHIP 47 5% 1/10W
R941 1-216-807-11 METAL CHIP 68 5% 1/10W D901 6-500-886-01 DIODE RSA6.1ENTR
R942 1-216-805-11 METAL CHIP 47 5% 1/10W D902 8-719-083-66 DIODE UDZSTE-1718B
R943 1-216-809-11 METAL CHIP 100 5% 1/10W D981 8-719-069-54 DIODE UDZSTE-175.1B
R944 1-216-805-11 METAL CHIP 47 5% 1/10W D982 8-719-988-61 DIODE 1SS355TE-17
R945 1-216-807-11 METAL CHIP 68 5% 1/10W < IC >

R946 1-216-805-11 METAL CHIP 47 5% 1/10W
R947 1-216-809-11 METAL CHIP 100 5% 1/10W IC901 6-707-063-01 IC LC75826WH-US-E
R948 1-216-805-11 METAL CHIP 47 5% 1/10W IC971 6-600-163-01 IC RS-770 (IR)
R949 1-216-807-11 METAL CHIP 68 5% 1/10W
< JUMPER RESISTOR >
R950 1-216-805-11 METAL CHIP 47 5% 1/10W
R951 1-216-809-11 METAL CHIP 100 5% 1/10W JP935 1-216-864-11 SHORT CHIP 0
R952 1-216-805-11 METAL CHIP 47 5% 1/10W JP961 1-216-864-11 SHORT CHIP 0
R953 1-216-807-11 METAL CHIP 68 5% 1/10W
R954 1-216-807-11 METAL CHIP 68 5% 1/10W < LIQUID CRYSTAL DISPLAY >
R955 1-216-813-11 METAL CHIP 220 5% 1/10W LCD901 1-805-729-11 DISPLAY PANEL, LIQUID CRYSTAL
R956 1-216-813-11 METAL CHIP 220 5% 1/10W
R957 1-216-811-11 METAL CHIP 150 5% 1/10W < DIODE >
R958 1-216-811-11 METAL CHIP 150 5% 1/10W
R959 1-216-811-11 METAL CHIP 150 5% 1/10W LED931 6-500-206-01 LED LBA676-K2L1L2 (LCD BACK LIGHT)
LED932 6-500-206-01 LED LBA676-K2L1L2 (LCD BACK LIGHT)
R960 1-216-811-11 METAL CHIP 150 5% 1/10W LED941 6-500-450-01 LED CL-195SR-CD-T (> M)
R961 1-216-807-11 METAL CHIP 68 5% 1/10W LED942 6-500-450-01 LED CL-195SR-CD-T (. m)
R962 1-216-805-11 METAL CHIP 47 5% 1/10W LED951 6-500-450-01 LED CL-195SR-CD-T (DISC-R ILLUMI)
R963 1-216-803-11 METAL CHIP 33 5% 1/10W
R967 1-216-815-11 METAL CHIP 330 5% 1/10W LED952 6-500-450-01 LED CL-195SR-CD-T (DISC-L ILLUMI)
R972 1-216-809-11 METAL CHIP 100 5% 1/10W < SWITCH >

R973 1-216-864-11 SHORT CHIP 0
R974 1-216-864-11 SHORT CHIP 0 LSW901 1-786-805-11 SWITCH, TACTILE (WITH LED) (Z)
R976 1-216-864-11 SHORT CHIP 0 LSW902 1-786-805-11 SWITCH, TACTILE (WITH LED) (OFF)
R977 1-216-809-11 METAL CHIP 100 5% 1/10W LSW903 1-786-805-11 SWITCH, TACTILE (WITH LED) (SOURCE)
LSW904 1-786-800-11 SWITCH, TACTILE (WITH LED) (VOL –)
R978 1-216-809-11 METAL CHIP 100 5% 1/10W LSW905 1-786-805-11 SWITCH, TACTILE (WITH LED) (SEL)
R979 1-216-809-11 METAL CHIP 100 5% 1/10W
R981 1-216-811-11 METAL CHIP 150 5% 1/10W LSW906 1-786-800-11 SWITCH, TACTILE (WITH LED) (VOL +)
41
CDX-S2050C/S2050V
KEY (S2050V) MAIN
LSW907 1-786-805-11
SWITCH, TACTILE (WITH LED) (MODE) R955 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW908 1-786-805-11
SWITCH, TACTILE (WITH LED) (ATT) R956 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW909 1-786-805-11
SWITCH, TACTILE (WITH LED) (EQ3) R957 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW910 1-786-800-11
SWITCH, TACTILE (WITH LED) R961 1-216-805-11 METAL CHIP 47 5% 1/10W
(SEEK +/> M) R962 1-216-803-11 METAL CHIP 33 5% 1/10W
(SEEK –/m .) R963 1-216-864-11 SHORT CHIP 0
R967 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW912 1-786-805-11 SWITCH, TACTILE (WITH LED) (AF/TA) R972 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW913 1-786-805-11 SWITCH, TACTILE (WITH LED) (PTY) R973 1-216-864-11 SHORT CHIP 0
LSW914 1-786-805-11 SWITCH, TACTILE (WITH LED) (6) R974 1-216-864-11 SHORT CHIP 0
LSW915 1-786-805-11 SWITCH, TACTILE (WITH LED) (5)
LSW916 1-786-805-11 SWITCH, TACTILE (WITH LED) (4/SHUF) R976 1-216-864-11 SHORT CHIP 0
R977 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW917 1-786-805-11 SWITCH, TACTILE (WITH LED) (3/REP) R978 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW918 1-786-805-11 SWITCH, TACTILE (WITH LED) (2) R979 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW919 1-786-805-11 SWITCH, TACTILE (WITH LED) (1) R981 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW920 1-786-805-11 SWITCH, TACTILE (WITH LED) (SENS/BTM)
LSW921 1-786-805-11 SWITCH, TACTILE (WITH LED) (DSPL/DIM) R982 1-216-811-11 METAL CHIP 150 5% 1/10W
R983 1-216-864-11 SHORT CHIP 0
< TRANSISTOR > R984 1-216-821-11 METAL CHIP 1K 5% 1/10W
R985 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q921 8-729-027-58 TRANSISTOR DTC143ZKA-T146 R986 1-216-821-11 METAL CHIP 1K 5% 1/10W
< RESISTOR > R987 1-216-857-11 METAL CHIP 1M 5% 1/10W

*************************************************************
R901 1-216-819-11 METAL CHIP 680 5% 1/10W
R902 1-216-819-11 METAL CHIP 680 5% 1/10W A-1082-337-A MAIN BOARD, COMPLETE (S2050V)
R903 1-216-819-11 METAL CHIP 680 5% 1/10W A-1083-043-A MAIN BOARD, COMPLETE (S2050C)
R904 1-216-821-11 METAL CHIP 1K 5% 1/10W *********************
R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
7-621-284-40 SCREW +P 2.6X10
R906 1-216-823-11 METAL CHIP 1.5K 5% 1/10W 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
R907 1-216-819-11 METAL CHIP 680 5% 1/10W 7-685-793-09 SCREW +PTT 2.6X8 (S)
R908 1-216-819-11 METAL CHIP 680 5% 1/10W 7-685-795-09 SCREW +PTT 2.6X12 (S)
R909 1-216-819-11 METAL CHIP 680 5% 1/10W
R910 1-216-821-11 METAL CHIP 1K 5% 1/10W < CAPACITOR >
R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10W C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R912 1-216-823-11 METAL CHIP 1.5K 5% 1/10W C2 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C3 1-126-963-11 ELECT 4.7uF 20% 50V
R914 1-216-827-11 METAL CHIP 3.3K 5% 1/10W C4 1-126-947-11 ELECT 47uF 20% 35V
R915 1-216-829-11 METAL CHIP 4.7K 5% 1/10W C5 1-126-947-11 ELECT 47uF 20% 35V
R916 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R917 1-216-833-11 METAL CHIP 10K 5% 1/10W C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R918 1-216-835-11 METAL CHIP 15K 5% 1/10W C11 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
R922 1-216-811-11 METAL CHIP 150 5% 1/10W C51 1-126-947-11 ELECT 47uF 20% 35V
R936 1-216-807-11 METAL CHIP 68 5% 1/10W C59 1-164-237-11 CERAMIC CHIP 16PF 5% 50V
42
CDX-S2050C/S2050V
MAIN
C308 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C769 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C401 1-126-964-11 ELECT 10uF 20% 50V C771 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C406 1-126-960-11 ELECT 1uF 20% 50V C776 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C407 1-126-960-11 ELECT 1uF 20% 50V
C412 1-104-665-11 ELECT 100uF 20% 25V < CONNECTOR >
C431 1-126-964-11 ELECT 10uF 20% 50V CN601 1-774-701-21 PIN, CONNECTOR 16P
CN701 1-794-311-21 PLUG, CONNECTOR 12P
C432 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P
C441 1-126-964-11 ELECT 10uF 20% 50V
C442 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V < DIODE >
C451 1-126-964-11 ELECT 10uF 20% 50V
C452 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V D1 8-719-069-55 DIODE UDZSTE-175.6B
D479 8-719-988-61 DIODE 1SS355TE-17
C461 1-126-964-11 ELECT 10uF 20% 50V D501 8-719-914-44 DIODE DAP202K
C462 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V D502 8-719-060-48 DIODE RB751V-40TE-17
C471 1-126-964-11 ELECT 10uF 20% 50V D580 8-719-056-84 DIODE UDZ-TE-17-7.5B
C474 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C479 1-126-947-11 ELECT 47uF 20% 35V D581 8-719-083-66 DIODE UDZSTE-1718B
D601 8-719-049-38 DIODE 1N5404TU
C481 1-126-964-11 ELECT 10uF 20% 50V D609 8-719-978-33 DIODE DTZ-TT11-6.8B
C484 1-163-251-11 CERAMIC CHIP 100PF 5% 50V D617 8-719-083-66 DIODE UDZSTE-1718B
C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D651 8-719-083-66 DIODE UDZSTE-1718B
C503 1-104-665-11 ELECT 100uF 20% 25V D701 6-500-886-01 DIODE RSA6.1ENTR
D702 6-500-886-01 DIODE RSA6.1ENTR
C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D719 8-719-083-66 DIODE UDZSTE-1718B
C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V D751 6-500-522-01 DIODE 10EDB40-TA1B2
C508 1-162-917-11 CERAMIC CHIP 15PF 5% 50V D752 6-500-522-01 DIODE 10EDB40-TA1B2
C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D753 6-500-522-01 DIODE 10EDB40-TA1B2
D754 6-500-522-01 DIODE 10EDB40-TA1B2
C511 1-104-665-11 ELECT 100uF 20% 25V D755 6-500-522-01 DIODE 10EDB40-TA1B2
D759 6-500-522-01 DIODE 10EDB40-TA1B2
C601 1-131-868-81 ELECT 3300uF 20% 16V D762 6-500-522-01 DIODE 10EDB40-TA1B2
C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D763 8-719-988-61 DIODE 1SS355TE-17
D764 8-719-988-61 DIODE 1SS355TE-17
C622 1-126-916-11 ELECT 1000uF 20% 6.3V < FERRITE BEAD >
C623 1-126-916-11 ELECT 1000uF 20% 6.3V
C631 1-126-960-11 ELECT 1uF 20% 50V FB1 1-469-844-11 INDUCTOR 2.2uH
C750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V FB301 1-216-864-11 SHORT CHIP 0
FB302 1-216-864-11 SHORT CHIP 0
C751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V FB303 1-469-876-11 INDUCTOR, FERRITE BEAD
C752 1-126-947-11 ELECT 47uF 20% 35V FB304 1-216-295-11 SHORT CHIP 0
C753 1-128-551-11 ELECT 22uF 20% 63V
C754 1-126-961-11 ELECT 2.2uF 20% 50V FB305 1-500-245-11 INDUCTOR, FERRITE BEAD
C755 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V FB306 1-500-245-11 INDUCTOR, FERRITE BEAD
FB307 1-469-876-11 INDUCTOR, FERRITE BEAD
C758 1-126-964-11 ELECT 10uF 20% 50V FB311 1-216-864-11 SHORT CHIP 0
C759 1-126-964-11 ELECT 10uF 20% 50V
C760 1-104-665-11 ELECT 100uF 20% 25V FB501 1-500-245-11 INDUCTOR, FERRITE BEAD
C761 1-126-964-11 ELECT 10uF 20% 50V FB561 1-469-876-11 INDUCTOR, FERRITE BEAD
FB562 1-216-864-11 SHORT CHIP 0
43
CDX-S2050C/S2050V
MAIN
FB604 1-216-295-11 SHORT CHIP 0 Q651 8-729-120-28 TRANSISTOR 2SC1623-L5L6
FB605 1-216-864-11 SHORT CHIP 0 Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146
FB606 1-216-864-11 SHORT CHIP 0
< RESISTOR >
< IC >
R1 1-216-821-11 METAL CHIP 1K 5% 1/10W
IC51 6-803-747-01 IC TDA7333013TR R2 1-414-595-11 INDUCTOR, FERRITE BEAD
IC401 6-705-372-01 IC BD3808FS-FE2 R3 1-414-595-11 INDUCTOR, FERRITE BEAD
IC501 6-804-911-01 IC MB90488BPF-G-117-BNDE1 R4 1-216-839-11 METAL CHIP 33K 5% 1/10W
IC602 8-759-659-13 IC PST3428UL R5 1-216-843-11 METAL CHIP 68K 5% 1/10W
IC750 6-705-360-02 IC TDA8588BJ/N2/R1
R6 1-216-839-11 METAL CHIP 33K 5% 1/10W
< JACK > R7 1-216-843-11 METAL CHIP 68K 5% 1/10W
R8 1-216-839-11 METAL CHIP 33K 5% 1/10W
J1 1-815-185-13 JACK (ANTENNA) R9 1-216-843-11 METAL CHIP 68K 5% 1/10W
J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT) R12 1-216-864-11 SHORT CHIP 0
J561 1-566-822-41 JACK (REMOTE IN)
R13 1-216-864-11 SHORT CHIP 0
< JUMPER RESISTOR > R29 1-216-809-11 METAL CHIP 100 5% 1/10W
R51 1-216-797-11 METAL CHIP 10 5% 1/10W
JC1 1-216-864-11 SHORT CHIP 0 R52 1-216-797-11 METAL CHIP 10 5% 1/10W
JC12 1-216-864-11 SHORT CHIP 0 R53 1-414-595-11 INDUCTOR, FERRITE BEAD
JC401 1-216-864-11 SHORT CHIP 0
JC445 1-216-296-11 SHORT CHIP 0 R54 1-216-833-11 METAL CHIP 10K 5% 1/10W
JC446 1-216-864-11 SHORT CHIP 0 R55 1-216-864-11 SHORT CHIP 0
R56 1-414-595-11 INDUCTOR, FERRITE BEAD
JC504 1-216-864-11 SHORT CHIP 0
R61 1-216-821-11 METAL CHIP 1K 5% 1/10W
JC581 1-216-296-11 SHORT CHIP 0
JC753 1-216-296-11 SHORT CHIP 0 R405 1-218-881-11 METAL CHIP 27K 0.5% 1/10W
R406 1-216-809-11 METAL CHIP 100 5% 1/10W
JC756 1-216-864-11 SHORT CHIP 0
R409 1-216-809-11 METAL CHIP 100 5% 1/10W
< COIL > R410 1-216-809-11 METAL CHIP 100 5% 1/10W
R411 1-216-809-11 METAL CHIP 100 5% 1/10W
L1 1-469-844-11 INDUCTOR 2.2uH R431 1-216-809-11 METAL CHIP 100 5% 1/10W
L51 1-216-295-11 SHORT CHIP 0 R432 1-216-841-11 METAL CHIP 47K 5% 1/10W
L301 1-469-844-11 INDUCTOR 2.2uH
L501 1-500-245-11 INDUCTOR, FERRITE BEAD R433 1-216-864-11 SHORT CHIP 0
L601 1-456-617-11 COIL, CHOKE R441 1-216-809-11 METAL CHIP 100 5% 1/10W
R442 1-216-841-11 METAL CHIP 47K 5% 1/10W
< TRANSISTOR > R443 1-216-864-11 SHORT CHIP 0
R451 1-216-809-11 METAL CHIP 100 5% 1/10W
Q1 8-729-106-68 TRANSISTOR 2SD1615A-GP
Q22 1-801-806-11 TRANSISTOR DTC144EKA R452 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q51 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R R453 1-216-864-11 SHORT CHIP 0
Q431 6-550-752-01 TRANSISTOR DTC614TKT146 R461 1-216-809-11 METAL CHIP 100 5% 1/10W
Q441 6-550-752-01 TRANSISTOR DTC614TKT146 R462 1-216-841-11 METAL CHIP 47K 5% 1/10W
R463 1-216-864-11 SHORT CHIP 0
Q461 6-550-752-01 TRANSISTOR DTC614TKT146 R471 1-216-809-11 METAL CHIP 100 5% 1/10W
Q471 6-550-752-01 TRANSISTOR DTC614TKT146 R472 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q478 1-801-806-11 TRANSISTOR DTC144EKA R479 1-216-805-11 METAL CHIP 47 5% 1/10W
Q479 8-729-027-23 TRANSISTOR DTA114EKA-T146 R481 1-216-809-11 METAL CHIP 100 5% 1/10W
R482 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146 R501 1-216-864-11 SHORT CHIP 0
Q581 1-801-806-11 TRANSISTOR DTC144EKA R502 1-216-809-11 METAL CHIP 100 5% 1/10W
Q582 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R503 1-216-809-11 METAL CHIP 100 5% 1/10W
Q631 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R504 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
44
CDX-S2050C/S2050V
MAIN SENSOR SERVO
R505 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R583 1-216-821-11 METAL CHIP 1K 5% 1/10W
R508 1-216-864-11 SHORT CHIP 0 R584 1-216-841-11 METAL CHIP 47K 5% 1/10W
R509 1-216-811-11 METAL CHIP 150 5% 1/10W R585 1-216-849-11 METAL CHIP 220K 5% 1/10W
R512 1-216-809-11 METAL CHIP 100 5% 1/10W R631 1-249-425-11 CARBON 4.7K 5% 1/4W
R515 1-247-807-31 CARBON 100 5% 1/4W R634 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R516 1-247-807-31 CARBON 100 5% 1/4W R636 1-216-845-11 METAL CHIP 100K 5% 1/10W
R518 1-216-864-11 SHORT CHIP 0 R652 1-216-841-11 METAL CHIP 47K 5% 1/10W
R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R654 1-216-833-11 METAL CHIP 10K 5% 1/10W
R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R671 1-216-809-11 METAL CHIP 100 5% 1/10W
R523 1-216-821-11 METAL CHIP 1K 5% 1/10W R672 1-216-809-11 METAL CHIP 100 5% 1/10W
R524 1-216-821-11 METAL CHIP 1K 5% 1/10W R673 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R528 1-216-845-11 METAL CHIP 100K 5% 1/10W R677 1-216-864-11 SHORT CHIP 0
R537 1-216-845-11 METAL CHIP 100K 5% 1/10W
< SWITCH >
R539 1-216-864-11 SHORT CHIP 0
R540 1-216-845-11 METAL CHIP 100K 5% 1/10W S702 1-786-826-11 SWITCH, TACTILE (RESET)
R541 1-216-845-11 METAL CHIP 100K 5% 1/10W
R543 1-216-821-11 METAL CHIP 1K 5% 1/10W < TUNER >
R544 1-216-821-11 METAL CHIP 1K 5% 1/10W
TU1 A-3220-961-A TUNER UNIT (TUX-032)
R548 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2050C) < VIBRATOR >
R550 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2050V) X51 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz)
R551 1-216-845-11 METAL CHIP 100K 5% 1/10W X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
R557 1-216-809-11 METAL CHIP 100 5% 1/10W X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
R559 1-216-845-11 METAL CHIP 100K 5% 1/10W *************************************************************
R560 1-216-845-11 METAL CHIP 100K 5% 1/10W SENSOR BOARD

R561 1-216-845-11 METAL CHIP 100K 5% 1/10W **************
R562 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2050C) < SWITCH >
R563 1-216-845-11 METAL CHIP 100K 5% 1/10W
R564 1-216-845-11 METAL CHIP 100K 5% 1/10W SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
R565 1-216-845-11 METAL CHIP 100K 5% 1/10W *************************************************************
R566 1-216-845-11 METAL CHIP 100K 5% 1/10W
(S2050V) A-1082-670-A SERVO BOARD, COMPLETE
R567 1-216-845-11 METAL CHIP 100K 5% 1/10W **********************
R570 1-216-817-11 METAL CHIP 470 5% 1/10W
R571 1-216-845-11 METAL CHIP 100K 5% 1/10W < CAPACITOR >
R577 1-216-845-11 METAL CHIP 100K 5% 1/10W C6 1-100-381-11 ELECT CHIP 10uF 20% 16V
45
CDX-S2050C/S2050V
SERVO
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R2 1-216-809-11 METAL CHIP 100 5% 1/10W
C19 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R6 1-216-833-11 METAL CHIP 10K 5% 1/10W
C21 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R8 1-414-760-21 FERRITE, EMI (SMD) (1608)
C23 1-162-923-11 CERAMIC CHIP 47PF 5% 50V R9 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
C25 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V R10 1-414-760-21 FERRITE, EMI (SMD) (1608)
C30 1-162-921-11 CERAMIC CHIP 33PF 5% 50V R15 1-216-797-11 METAL CHIP 10 5% 1/10W
C31 1-162-925-11 CERAMIC CHIP 68PF 5% 50V R41 1-216-821-11 METAL CHIP 1K 5% 1/10W
C38 1-104-609-11 ELECT CHIP 100uF 20% 4V R72 1-216-842-11 METAL CHIP 56K 5% 1/10W
R84 1-216-837-11 METAL CHIP 22K 5% 1/10W
< CONNECTOR > R85 1-216-833-11 METAL CHIP 10K 5% 1/10W
CN1 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P < SWITCH >

CN2 1-815-016-21 CONNECTOR, FFC/FPC (ZIF) 16P
SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< FERRITE BEAD >
< VIBRATOR >
FB1 1-216-864-11 SHORT CHIP 0
FB2 1-414-760-21 FERRITE, EMI (SMD) (1608) X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz)
FB3 1-414-760-21 FERRITE, EMI (SMD) (1608) *************************************************************
< IC > MISCELLANEOUS

***************
IC1 6-703-699-01 IC uPD63712GC-8EU-A
IC2 6-705-002-01 IC BA5966FP-FE2 6 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
0 153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)
< FERRITE BEAD > 154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901)
FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
JR40 1-414-760-21 FERRITE, EMI (SMD) (1608) M902 A-3337-638-A MOTOR ASSY, SL (SLED)
JR41 1-414-760-21 FERRITE, EMI (SMD) (1608)
JR90 1-414-760-21 FERRITE, EMI (SMD) (1608) M903 A-1075-792-A MOTOR ASSY, LE (LOADING)
JR91 1-414-760-21 FERRITE, EMI (SMD) (1608) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
*************************************************************
< TRANSISTOR >
Q1 8-729-904-87 TRANSISTOR 2SB1197K-R
< RESISTOR >
R1 1-216-841-11 METAL CHIP 47K 5% 1/10W
The components identified by

mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
46 specified.
CDX-S2050C/S2050V
Ref. No. Part No. Description Remark

ACCESSORIES
************
2-348-403-21 MANUAL, INSTRUCTION (ENGLISH,GERMAN,

FRENCH,ITALIAN,DUTCH)
2-348-404-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN,FRENCH,ITALIAN,DUTCH)
X-2024-133-1 CASE ASSY (for FRONT PANEL)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS

***************************************
301 X-3382-647-1 FRAME ASSY, FITTING

302 1-465-459-41 ADAPTOR, ANTENNA
303 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)
304 3-246-011-01 KEY (FRAME)
305 2-187-743-01 COLLAR
306 X-3366-972-2 SCREW ASSY (EXP), FITTING
301 302 303
304 305
×2
306
47
CDX-S2050C/S2050V
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision

1.0 2005.01 New
48

Sony cdx-s2050c s2050v Ver.1.0

Uploaded by

Copyright:

Available Formats

Sony cdx-s2050c s2050v Ver.1.0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony cdx-s2050c s2050v Ver.1.0

Uploaded by

Copyright:

Available Formats

CDX-S2050C/S2050V

SERVICE MANUAL AEP Model

• The tuner and CD sections have no adjustments.

Tuner section General

FM/MW/LW COMPACT DISC PLAYER

This compact disc player is classified as a CLASS 1 LASER

This label is located on the bottom of the chassis.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

Notes on Chip Component Replacement

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

Notes on CD-DA/CD-R/CD-RW z UNLEADED SOLDER

: LEAD FREE MARK

EXTENSION CABLE AND SERVICE POSITION

MAIN BOARD J-2502-076-1

5. ELECTRICAL PARTS LIST ......................................... 40

Location of controls and basic operations

SOURCE MODE ATT EQ3 SEEK

DIM BTM REP SHUF

2-1. SUB PANEL (LCD) ASSY

2-2. CD MECHANISM BLOCK

2-5. ROLLER ARM ASSY

2-6. CHASSIS (OP) ASSY

2-8. SL MOTOR ASSY (M902)

2-7. OPTICAL PICK-UP 2-9. LE MOTOR ASSY (M903)

Note : Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (LCD) ASSY

4 sub panel (LCD) assy

2-2. CD MECHANISM BLOCK

2-3. MAIN BOARD

2-4. CHASSIS (T) SUB ASSY

6 chassis (T) sub assy

2-5. ROLLER ARM ASSY

5 roller arm assy

2-6. CHASSIS (OP) ASSY

0 coil spring (damper)

5 gear (LE1) 9 two coil springs (damper)

3 tension coil spring (KF60)

2-7. OPTICAL PICK-UP

2 chucking arm sub assy

1 tension coil spring (CHKG)

2-8. SL MOTOR ASSY (M902)

2 SL motor assy (M902)

2-9. LE MOTOR ASSY (M903)

0 gear (LE) assy 8 screw

1 Remove the soldering.

2-10. SERVO BOARD

1 Remove the eight solderings. 6 SERVO board

2 Remove the three solderings.

4 toothed lock screw

• R-ch is omitted due to same as L-ch.

M901 17 VO3+ OPIN3+ 24 58 MD+ SW4 100 CD_LIMIT

M903 10 VOL+ FWD 1 97 CD LM LO

3-2. BLOCK DIAGRAM – MAIN SECTION –

RDS DECODER TEL MUTE 13

3-3. BLOCK DIAGRAM – DISPLAY SECTION – • Circuit Boards Location

BU+3.3V 2 VDD VOUT 1 77 RESET

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Waveforms

For schematic diagrams. For printed wiring boards.