Boqpdf

BILL OF QUANTITY
dk;Z dk uke& tuin dUUkkSt esa fLFkr yk[k cgkslh LFky dk lkSUn;hZdj.k ,ao i;ZVu fodkl dk;ZA
S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

1 Earth work in excavation by mechanical means 2.8.1 116.64 CUM 181.75 21200.21
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10
sqm on plan), including dressing of sides and ramming
of bottoms, lift upto 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m.
2 Supplying and stacking of good earth at site. 16.3.9 16.20 CUM 541.49 8772.18
3 Filling available excavated earth (excluding rock) in 2.25 86.48 CUM 489.12 42299.45
trenches, plinth, sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
4 Providing and laying in position cement concrete of 4.1.8 26.80 CUM 4756.48 127473.64
specified grade excluding the cost of centering and
shuttering - All work up to plinth level : 1:4:8 (1 Cement
: 4 coarse sand (zone-III) : 8 graded stone aggregate 40
mm nominal size)
5.00
5 Supplying and filling in plinth with sand under floors, 2.27 14.82 CUM 1482.91 21978.93
including watering, ramming, consolidating and
dressing complete.
6 Treatment of soil under existing floors using chemical 2.35.3.1 117.19 SQM 216.49 25370.75
emulsion @ one litre per hole, 300 mm apart including
drilling 12 mm diameter holes and plugging with
cement mortar 1 :2 (1 cement : 2 Coarse sand) to match
the existing floor: With Chlorpyriphos E.C. 20% with 1%
concentration
7 Providing and laying in position specified grade of 5.10

reinforced cementconcrete, excluding the cost of
centering, shuttering, finishing andreinforcement 1:1.5:3
(1 cement : 1.5 coarse sand (zone-III) derived from
naturalsources : 3 graded stone aggregate 20 mm
nominal size derived from natural sources)
(I) Upto plinth level
(i) R.C.C. work in Footing 5.1.2 19.47 CUM 6316.19 122958.72
(ii) R.C.C. work in Beam 5.1.2 6.36 CUM 6316.19 40182.37
(iii) R.C.C. work in Columns 5.1.2 3.97 CUM 6316.19 25087.74
Above plinth to Floor-v level

Providing and laying in position specified grade of
reinforced cementconcrete, excluding the cost of
centering, shuttering, finishing andreinforcement 1:1.5:3
(1 cement : 1.5 coarse sand (zone-III) derived from
naturalsources : 3 graded stone aggregate 20 mm
nominal size derived from natural sources)
(iii) R.C.C. work in Columns 5.2.2 4.95 CUM 7578.07 37485.69
(i) R.C.C. work in Lintel 5.2.2 2.50 CUM 7578.07 18945.18
(ii) R.C.C. work in Beam 5.2.2 18.35 CUM 7578.07 139054.50
(iv) R.C.C. work in Slab 5.2.2 20.88 CUM 7578.07 158208.17

8 Brick work with common burnt clay F.P.S. (non 6.1.2 84.80 CUM 4980.09 422323.82
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and sizes in :Cement mortar 1:6 (1 cement : 6
coarse sand)
9 Providing and laying damp-proof course 40mm thick 4.1 17.11 SQM 286.88 4909.75
with cement concrete 1:2:4 (1 cement : 2 coarse sand
(zone-III) derived from natural sources : 4 graded stone
aggregate 12.5mm nominal size derived from natural
sources)
10 Providing & applying a coat of residual petroleum 4.13 17.11 SQM 102.05 1746.53
bitumen of grade of VG-10 of approved quality using
1.7kg per square metre on damp proof course after
cleaning the surface with brushes and finally with a
piece of cloth lightly soaked in kerosene oil.
11 Brick Work with common burnt clay ( non modular) 6.4.1

bricks of class - 150 in superstructure above plinth level
up to floor V level in all shapes and sizes in: Cement
mortar 1:4 ( 1 cement : 4 coarse sand)
(a) Ground Floor 13.99 CUM 6524.69 91255.98
12 Steel reinforcement for R.C.C. work including 5.22.6

straightening, cutting, bending, placing in position and
binding all complete upto plinth level. Thermo-
Mechanically Treated bars of grade Fe-500D or more.
(a) Ground Floor 110.29 QTL 7530.63 830552.77
13 15 mm plinth plaster (1 cement :4 coarse sand) 13.5.1 16.45 SQM 287.50 4729.16
14 12mm cement plaster in single coat on fair side of single 13.4.2

or half brick wall for exterior plastering up to floor two
level including internal rounded angles chamfers,
and/or rounded angles not exceeding 80mm in girth
and finished even and smooth no extra for mixing any
additive. 1:6 (1 cement: 6 coarse sand)
(a) Ground Floor 142.74 SQM 239.95 34251.58
15 15 mm cement plaster on the rough side of single or half 13.5.2

brick wall of mix : 1:6 (1 cement: 6 coarse sand)
16 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine 13.16.1 100.34 SQM 209.79 21050.25
sand)
17 Making plinth protection 50mm thick of cement 4.17 30.60 SQM 523.20 16009.88
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) over 75mm thick bed of
dry brick ballast 40 mm nominal size, well rammed and
consolidated and grouted with fine sand, including
necessary excavation, levelling & dressing & finishing
the top smooth.
18 Add for plaster drip course/ groove in plastered surface 5.3 116.62 RM 54.74 6384.11
or moulding to R.C.C. projections.

19 Kota stone slab flooring over 20 mm (average) thick 11.26.1
base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab,
including rubbing and polishing complete with base of
cement mortar 1 : 4 (1 cement : 25 mm thick
20 Kota stone slabs 20 mm thick in risers of steps, skirting, 11.26.1

dado and pillars laid on 12 mm (average) thick cement
mortar 1:3 (1 cement: 3 coarse sand) and jointed with
grey cement slurry mixed with pigment to match the
shade of the slabs, including rubbing and polishing
complete.
21 Supply and fixing 6 mm China white glazed tiles in 11.37

flooring or in skirting or dado laid with 1:3 cement and
approved coarse sand mortar finished with white
cement slurry jointing and polishing complete including
supply of all materials, labour and tool sand plants etc.
required for proper completion of the work. (Size of tiles
upto 300x300mm).
22 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand 11.3.1 81.81 SQM 447.72 36627.80
: 4 gradedstone aggregate) finished with a floating coat
of neat cement, includingcement slurry, but excluding
the cost of nosing of steps etc. complete 40 mm thick
with 20 mm nominal size stone aggregate
23 Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) non-decorative type, core
of block board construction with frame of 1st class hard
wood and well matched commercial 3 ply veneering
with vertical grains or cross bands and face veneers on
both faces of shutters :
a) 35 mm thick Single leaf 9.20.1 12.18 SQM 2425.62 29544.00
24 Mild steel or iron work of small sizes and sections such

as holding down bolts, hold fast tierods,gratings etc. (
when not included in an over all rates) wrought to
required from including supply of steel and its wastage
including cost of bolts, nuts if required for and welding,
grinding and making holes as required completion of
work fabrication of holes doors, chaukhats nosing.
(a) Fabrication of hold fast for door, chaukhats and 10.1 36.00 KG 81.94 2949.83
windows.
(b) Providing & fixing of door / windows grill. 9.48.1 2.57 KG 152.99 392.41
(c) Angle iron chaukhat (40x40x5) 10.13.1 123.00 KG 98.94 12169.87
25 Fixing of Door, windows / ventilators chaukhats in MR

position.
(a) Door chaukhats 7.00 NOS 104.50 731.50
(b) Ventilator chaukhats 9.00 NOS 57.00 513.00

26 Steel Painting:Applying priming coat:(a) With ready 13.62.1 31.73 SQM 157.98 5013.07
mixed red oxide zink chromate primer of approved
brand and manufacture on steel galvanised iron/steel
works.(b) Painting with synthetic enamel paint of
approved brand and manufacture to give an even
shade: Two or more coats on new work.
27 Steel Painting:Applying priming coat:(a) With ready 24.36 SQM 157.98 3848.37
mixed red oxide zink chromate primer of approved
brand and manufacture on steel galvanised iron/steel
works.(b) Painting with synthetic enamel paint of
approved brand and manufacture to give an even
shade: Two or more coats on new work.
28 Painting with silicon & acrylic emulsion based water 13.60.1

thinnable sealer of approved brand and manufacture on
wet or patchy portion of plastered surfaces : Two coats
Internal wall surface)
29 Finishing walls (Two coats ) with exterior paint (Apex) 13.47.1

of approved brand and manufacture and of required
shade on undercoated wall surface to give even shade
@1.25 ltr./10 sqm including one coat of primer applied
@0.75 ltr./10sqm curing, cost of all materials, labours, T
& P etc. required for proper completion of the work.
30 Painting with silicon & acrylic emulsion based water 13.60.1

thinnable sealer of approved brand and manufacture on
wet or patchy portion of plastered surfaces : Two coats
Ceiling surface)
31 Providing and applying white cement based putty of 13.8

average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to prepare
the surface even and smooth complete.
32 Providing and fixing 150 mm bright finished floor 14.34 7.00 NOS. 189.54 1326.78
stainless steel door stopper with rubber cushion,
necessary brass screws etc. to suit shutter thickness
complete.
33 Providing and fixing aluminium sliding door bolts, ISI 9.96.2 7.00 NOS 181.96 1273.75
marked anodised (anodic coating not less than grade
AC 10 as per IS : 1868),transparent or dyed to required
colour or shade, with nuts and screws etc. complete. (a)
250mm x 16mm.
34 Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than grade
AC 10 as per IS : 1868 ) transparent or dyed to required
colour or shade, with necessary screws etc. complete
300 x 10mm 9.97.1 7.00 NOS 90.84 635.90

200 x 10mm 9.97.3 7.00 NOS 69.62 487.31

35 Providing and fixing aluminium handles, ISI marked, 9.100.1 14.00 NOS 46.26 647.63
anodised (anodic coating not less than grade AC 10 as
per IS : 1868) transparent or dyed to required colour or
shade, with necessary screws etc. complete (a) 125 mm.
36 Providing & laying "brick Coba" 12mm thick laid with

M-150 class brick bat coba 7.50 cm thick with gap of
15mm to each other, over 20mm thick base of cement
mortar 1:4 cement and coarse sand mixed with water
proofing compound spreading cement slurry mixed
with acrylic cement concrete water proofing compound
filled gaps of
coba & top of coba mortar mixed with water proofing
compound in 1:4 cement and coarse sand mortar
finished smooth & top mashed false square 30 cm x 30
cm and side wall parapet shall be mono lythic plaster
wall upto 30cm higher and junction and corner shall be
rounded by brick
ballast cement and coarse sand masonry coba with top 22.7.1 123.61 SQM 1176.27 145398.74
finished plaster mixed with acetic water proofing
compound @ 2% by weight & including S/o all material,
labour T & P etc complete for proper completion of
work.
37 Providing & fixing glass panes with putty and glazing 10.30.1 2.57 SQM 743.39 1906.80
clips in steel doors, windows, clerestory windows, all
complete with : 4.0 mm thick glass panes
38 Providing & fixing on roof pressed clay tile (Mangalore 161.64 SQM 302.66 48921.39
tile) of 20 mmnominal thickness and of approved size
and as per approved patternon steel frame work
complete (steel frame work to be paidseparately).
39 Providing & laying on roof pressed clay tile ridge 68.00 RM 67.66 4600.91
(Mangalore tile) of20mm thickness and of approved
pattern on steel frame workcomplete (steel frame work
to be paid separately).
40 Ornamental Work 72.00 SQM 11827.50 851580.00
41 Birds 1.00 NO 42750.00 42750.00

42 Crane 2.00 NO 71250.00 142500.00
43 Monkey 1.00 NO 80750.00 80750.00
44 Peacock 1.00 NO 128250.00 128250.00
45 Snake 1.00 NO 33250.00 33250.00
46 Centering and shuttering including strutting, propping
etc. and removal of form for all heights :
(a) Foundations, footings, bases of columns, etc. for mass 5.9.1 58.18 SQM 273.82 15930.77
concrete.
(b) Lintels, beams, plinth beams, girders, bressumers and 5.9.21 310.87 SQM 587.89 182756.21
cantilevers. with water proof ply 12 mm thick
(c) Columns,Pillars, Piers, Abutments, Posts and Struts. 5.9.6 181.17 SQM 671.23 121603.89
(d) Edges of slabs and breaks in floors and walls Under 20 5.9.16.1 123.61 RM 145.62 18000.06
cm wide.
PLUMBING WORKS

47 Providing and fixing water closet squatting pan (Indian 2.00 Each 4725.06 9450.12
type W.C. pan ) with 100 mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing cistern, including
flush pipe, with manually controlled device (handle
lever) conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good
the walls and floors wherever required:White Vitreous
china Orissa pattern W.C. pan of size 580x440 mm with
integral type foot rests
48 Providing and fixing white vitreous china pedestal type 3.00 Each 4409.45 13228.35
water closet ( European type W.C. pan ) with
seat and lid, 10 litre low level white P.V.C. flushing
cistern, including flush pipe, with manually controlled
device (handle lever) conforming to IS : 7231, with all
fittings and fixtures complete, including cutting and
making good the walls and floors wherever
required:W.C. pan with ISI marked white solid plastic
seat and lid.
49 Providing and fixing wash basin with C.I. brackets, 15

mm C.P. brass pillar taps, 32 mm C.P. brass waste of
standard pattern, including painting of fittings and
brackets, cutting and making good the walls wherever
require
White Vitreous China Flat back wash basin size 630x 5.00 Each 1848.97 9244.83
450 mm with a pair of 15 mm C.P. brass pillar tap.
50 Providing and fixing 600x450 mm beveled edge mirror 5.00 Each 1122.09 5610.44
of superior glass (of approved quality) complete with 6
mm thick hard board ground fixed to wooden cleats
with C.P. brass screws and washers complete.
51 Providing and fixing white vitreous china flat back half

stall urinal of size 580x380x350 mm with white PVC
automatic flushing cistern, with fittings, standard size
C.P. brass flush pipe, spreaders with unions and clamps
(all in C.P. brass) with waste fitting as per IS :2556, C.I.
trap with outlet grating and other couplings in C.P.
brass including painting of fittings and brackets,
cutting and making good the walls and floors wherever
required
Single half stall urinal with 5 litre P.V.C. automatic 3.00 Each 8429.10 25287.30
flushing cistern
Providing and fixing stone slab table rubbed, edges

rounded and polished of size 75x50cm deep and 1.8cm
thick fixed in Urinal partitions by cutting a chase of
appropriate width with chase cutter and embedding the
52
stone in the chase with epoxy grout or with cement
concrete 1:2:4 (1cement: 2coarse sand: 4graded stone
aggregate 6mm nominal size) as per direction of
Engineer-in-charge and finished smooth.
Granite Stone of approved shade 1.00 Sqm. 1865.21 1865.21
53 Providing and fixing CP Brass 32 mm size Bottal Trap 4.00 Each 721.99 2887.96
of approved quality & make and as per thedirection of
Enginer-in-charge.

54 Providing & fixing PTMT towl rail complete with 2.00 Each 495.02 990.05
brackets fixed to wooden cleats with cp brass screws
with concealed fitting arrangement of approved quality
and colour. 600 mm. long towl rail length of 645 mm.
width 78 mm. and effective height of 88 mm, weighing
not less than 190 gms.
55 Providing and fixing PTMT Liquid soap container 109 2.00 Each 117.55 235.10
mm wide ,125 mm high and 112 mm distance from wall
of standerd shape with bracket of the same material
with snap fittings of approved quality and colour
weighing not less than 105 gms
56 Providing and fixing on wall face unplasticised Rigid

PVC rain water pipes conforming to IS : 13592 Type A
including jointing with seal ring conforming to IS : 5382
leaving 10 mm gap for thermal expansion . (i) Single
socketed pipes.
a) 110mm diameter 75.00 RM 263.52 19763.97
57 Supply and fixing of UPVC S.W.R. pipe type-B

confirming to IS-13592 including jointing the pipes with
rubber ring,lubricant and UPVC SWR cupler confirming
to IS-14735. Also including excavation of treanches
cutting of walls and holes and repairing the walls,floors
and refilling the trenches as before but excluding supply
and cost of other fIttlings such as elbow,bend,tee and y-
tee including supply of al marerial labour and
T&P.Required for proper completion of work.
110 mm O.D. 10.00 Rm. 301.64 3016.44
58 Supply and fixing of UPVC S.W.R. pipe nahni trap size 5.00 Each 607.48 3037.39
100x75,110/90 mm confirming to IS-14735 self cleaning
design fixed in PCC 1:2:4 and supply and fixing of 125
mm dia heavy duty CP brass jali.
59 Supply and fixing of UPVC S.W.R. plain bend

confirming to IS-14735.
Size 110 mm 14.00 Each 136.16 1906.22
60 Supply and fixing of UPVC S.W.R. plain tee confirming

to IS-14735.
Size 110x110x110 mm 6.00 Each 178.05 1068.32
61 Supply and fixing of UPVC S.W.R. plain Y confirming to

IS-14735.
Size 110 mm 6.00 Each 199.00 1194.01
62 Laying cement concrete 1:5:10 in haunching P.V.C./

S.W. Pipes including conccrete for bedding necessary
form work and curing complete.around P.V.C Soil and
waste pipe including bed concrete as per standard
design(embedded in the flooring / ground)
110 mm diameter 28.00 Metre 309.74 8672.82

63 Making khurras 45x45 cm with average minimum
thickness of 5 cm cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate of 20 mm
nominal size) over PVC sheet 1m x 1 m x 400 micron,
finished with 12 mm cement plaster 1:3 (1 cement : 3
coarse sand) and a coat of neat
cement,punning,rounding the edges and making and
finishing the outlet complete.
a) 110mm 12.00 Nos. 208.25 2499.04
64 Providing and fixing unplasticised -PVC pipe clips of

approved design to unplasticised - PVC rain water
pipes by means of 50x50x50mm hard wood plugs,
screwed with M.S. screws of required length including
cutting brick work and fixing in cement mortar 1:4 (1
cement : 4 coarse sand) and making good the wall etc.
complete.
a) 110mm 12.00 Nos. 259.26 3111.12
65 Providing and fixing to the inlet mouth of rain water 12.00 Nos. 38.19 458.33
pipe cast iron grating 15 cm diameter and weighing not
less than 440 grams.
66 Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold
water supply including all CPVC plain & brass
threaded fittings including fixing the pipe with clamps
at 1.00m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement and testing
of joints complete as per direction of Engineer in
Charge.
Internal work-Exposed on wall
20mm dia nominal outer dia pipes 10.00 Rm. 233.91 2339.14

water supply including all CPVC plain & brass
threaded fittings i/c fixing the pipe with clamps at
1.00m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and the cost of
cutting chases and making good the same including
testiang of joints complete as per direction of Engineer
in Charge. Concealed work including cutting chases and
making good the walls etc.
a) 15mm dia nominal outer dia pipes 18.8.1 10.00 Rm. 347.59 3475.89
b) 20mm dia nominal outer dia pipes 18.8.2 10.00 Rm. 375.38 3753.79
c) 25mm dia nominal outer dia pipes 18.8.3 8.00 Rm. 437.98 3503.82
d) 32mm dia nominal outer dia pipes 18.8.4 5.00 Rm. 516.22 2581.08
68 Providing & fixing CP brass bib cock of approved

quality conforming to IS 8931
15mm nominal bore 18.49.1 2.00 Each 353.87 707.75
69 Providing & fixing C.P. brass long body bib cock of

approved quality conforming to IS standards and
weighing not less than 690 gms.
15mm nominal bore 18.51.1 4.00 Each 557.87 2231.47
70 Providing and fixing gun metal gate valve with wheel of

approved quality(screwed end)..

25mm dia nominal bore 2.00 Each 434.59 869.18
71 Providing and fixing ball valve (brass) of approved 18.18.3

quality, High or low pressure, with plastic floats
complete
25 mm nominal bore 2.00 Each 324.02 648.05
72 Supply and hoisting of Sintex or equivalent high density New

polyethylene seemless of piece moulded tanks and
placing the same in proper position including all taxes,
labour and T&P etc. for proper completion of work.
Tnak should be ISI marked, Sintex or equivalent.
For 500 litres 1000.00 Per Ltrs 6.98 6982.50
73 Providing and fixing gun metal gate valve with wheel of 18.17.1A
approved quality.
a) 20 mm dia nominal bore 2.00 Each 377.02 754.04
74 Excavating trenches in all kind of soil of required width

for pipes, cables etc. including excavation for sockets
and dressing of sides, ramming of bottoms, depth upto
1.5 m. including getting out the excavated soil & then
returning the soil as required,
in layers not exceeding 20cm in depth including
consolidating each deposited layer by ramming,
watering, etc & disposig of surplus excavated soil as
directed within a lead of 50m.
a) Pipes 80mm to 300mm diameter. 2.10.1.2 8.00 RM 245.89 1967.11
75 Providing, laying and joining PVC/swr pipes grade 'A'

with stiff mixture of cement mortar in the proportion of
1:1 (1 cement : 1 fine sand) including testing of joints etc.
complete.
a) 110mm diameter MR 8.00 RM 298.85 2390.81
76 Laying cement concrete 1:2:4 in haunching P.V.C./ PWD 279a

S.W.R Pipes including conccrete for bedding necessary
form work and curing complete.
a) 110mm dia. 0.36 CUM 4748.10 1709.32
77 Providing and fixing S.W. Gully trap grade 'A' complete

with C.I. grating brick masonry chamber and water
tight C.I.cover frame of 300 x 300mm. size (inside)
square mouth traps of "P" or "S" type traps.
a) 100 x 150 mm. dia. 19.4.2.1 2.00 Each 1909.02 3818.03
78 Constructing brick masonry manhole in cement mortar 19.7

1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4
mix (1 cement :2 coarse sand :4 graded stone aggregate
20mm nominal size), foundation concrete 1:4:8 mix (1
cement :4 coarse sand :8 graded stone aggregate 40mm
nominal size) inside plastering 12mm thick with cement
mortar 1:3 (1 cement :3 coarse sand) finished with
floating coat fo neat cement and making channels in
cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded
stone aggregate 20mm nminal size) finished with a
floating coat of neat cement complete as per standard
design

Inside size 900x800mm and 500mm deep including CI 19.7.1
cover with frame
With FPS bricks of class designation 75 19.7.1.1 1.00 Each 8917.04 8917.04
79 Replacement of M.S. foot rests including dismantiling

concrete blocks and fixing in manholes with 20x20x10
cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand
:6graded stone aggregate 20 mm nominal size) as per
standard design
With 20x20 mm square bar 19.17.1 4.00 Each 467.97 1871.87
ELECTRIFICATION WORKS
Wiring for light point/ fan point/ exhaust fan point/ 1.1
call bellpoint with 1.5 sq.mm FRLS PVC insulated
copper conductorsingle core cable in surface / recessed
steel conduit, with pianotype switch, phenolic
80 laminated sheet, suitable size MS box and
earthing the point with 1.5 sq.mm FRLS PVC insulated
copperconductor single core cable etc. as required..
Group A 1.1.1 Each 23 90.70 2086.00

Wiring for circuit/ submain wiring alongwith earth 1.7
wire with thefollowing sizes of FRLS PVC insulated
81
copper conductor, singlecore cable in surface/ recessed
steel conduit as required
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 1.7.2 Meter 50 276.58 13829.20
2 X 4 sq. mm + 1 X 4 sq. mm earth wire 1.7.3 Meter 25 320.81 8020.19
Supplying and fixing following modular switch/ socket 1.24

on theexisting modular plate & switch box including
82
connections butexcluding modular plate etc. as
required.
5/6 A Switch 1.24.1 Each 6 77.20 463.22
15/16 A Switch 1.24.3 Each 1 116.93 116.93
3 pin 5/6 A Socket outlet 1.24.4 Each 2 91.45 182.89
Supplying and fixing following size/ modules, GI box 1.27

83 alongwith modular base & cover plate for modular
switches in recess etc as required.
1 or 2 Module (75mmX75mm) 1.27.1 Each 4 223.37 893.46
3 Module 100mmX75mm) 1.27.2 Each 2 245.10 490.21
4 Module 125mmX75mm) 1.27.3 Each 4 257.10 1028.38
Supplying and fixing of following sizes of medium class 1.21

PVC conduit along with accessories in surface/recess
84 including cutting the wall and making good the same in
case of recessed conduit as required.
25mm 1.21.2 Meter 30 108.68 3260.54
Supplying and fixing modular blanking plate on the 1.26 Each 5 29.98 149.91
85 existing modular plate & switch box excluding modular
plate as
Supplying and fixing 3 pin, 5 A ceiling rose on the 1.33 Each 5 65.21 326.05
86 existing junction box/ wooden block including
connections etc. as required.

Installation ,Testing, Commissioning of wall bracket 1.35 Each 14 89.20 1248.75
/ceiling fittings of all sizes and shapes containing upto
87
two GLS/CFL/LED lamps per fitting, complete with all
accessories including connections etc. as required.
Installation of exhaust fan in the existing opening, 1.5

88 including making good the damage, connection, testing,
commissioning etc. as required.
Upto 450 mmsweep 1.50.1 Each 5 337.30 1686.49
Supplying and fixing following way, single pole and 2.3

neutral,sheet steel, MCB distribution board, 240 V, on
surface/ recess,complete with tinned copper bus bar,
89
neutral bus bar, earthbar, din bar, interconnections,
powder painted includingearthing etc. as required. (But
without MCB/RCCB/Isolator)
6 way , Double door 2.3.1 Each 1 1245.00 1245.00
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 2.1

kA, "C"curve, miniature circuit breaker suitable for
90 inductive load offollowing poles in the existing MCB DB
complete withconnections, testing and commissioning
etc. as required.
Single pole and neutral 2.10.2 Each 3 448.98 1346.94
Supplying and fixing single pole blanking plate in the 2.11 Each 4 9.74 38.98
91
existing MCB DB complete etc. as required.
Supply of AC 230/250 volts, 50 HZ exhaust fans NS Each 5 1386.67 6933.34

92 including providing nuts, bolts, mounting frame and
other accessories etc. complete
Supply and Fixing of LED Tube Light with batten

suitable for up to 1X22 watt LED tube light fitting
93
complete, excluding tube on surface complete in all
respect.
a) 1 X 22 W NS Each 4 891.96 3567.86
EXTERNAL , PLUMBING WORKS
94 Constructing brick masonry manhole in cement mortar 19.7
1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4
mix (1 cement :2 coarse sand :4 graded stone aggregate
20mm nominal size), foundation concrete 1:4:8 mix (1
cement :4 coarse sand :8 graded stone aggregate 40mm
nominal size) inside plastering 12mm thick with cement
mortar 1:3 (1 cement :3 coarse sand) finished with
floating coat fo neat cement and making channels in
cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded
stone aggregate 20mm nminal size) finished with a
floating coat of neat cement complete as per standard
design
95 Inside size 900x800mm and 450mm deep including CI 19.7.1

cover with frame (light duty) 455x610 mm internal
dimensions, total weight of cover and frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) :
With common burnt clay F.P.S. (non modular) bricks of 19.7.1.1 4.00 Each 8917.04 35668.15
class designation 7.5

96 Making connection of drain or sewer line with existing
manhole including breaking into and making good the
walls, floors with cement concrete 1:2:4 mix (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm nominal
size) cement plastered on both sides with cement mortar
( 1 cement : 3 coarse sand) finished with a floating coat
of neat cement and making necessary channels for the
drain etc. complete :
For pipes 100 to 250 mm diameter 19.21.1 4.00 Each 565.90 2263.59
97 Providing and laying cement concrete 1:5:10 (1 cement : 19.2

5 coarse sand : 10 graded stone aggregate 40 mm
nominal size) all-round S.W. pipes including bed
concrete as per standard design :
100 mm diameter S.W. pipe 19.2.1 25.00 Meter 673.64 16840.92
150 mm diameter S.W. pipe 19.2.2 15.00 Meter 823.83 12357.45

water supply, including all CPVC plain & brass
threaded fittings, including fixing the pipe with clamps
at 1.00 m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement
trenches,refiling and testing of joints complete as per
direction of e/ i external work
32mm nominal bore. 18.9.4 30.00 Rm. 306.25 9187.57
40mm nominal bore. 18.9.5 25.00 Rm. 393.15 9828.74
99 Providing and fixing gate valve with C.I wheel of

approved quility (screwed end):
32mm 18.17.2 2.00 Nos. 481.51 963.03
40mm 18.17.3 2.00 Nos. 576.82 1153.65
100 Constructing masonry Chamber 60x60x75 cm inside, in 18.33

brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.I. surface box 100 mm top
diameter, 160 mm bottom diameter and 180 mm deep (
inside) with chained lid and RCC top slab 1:1.5:3 mix (1
cement : 1.5 coarse sand : 3 graded stone aggregate 20
mm nominal size), including necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand : 10
graded stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of 18.33.1 1.00 Each 7584.67 7584.67
class designation 7.5
101 Hanching of CPVC pipe with PCC 1:2:4 ( 1 cement: 2 AR 15.00 Rm. 186.43 2796.49
coarse sand: 4 stone grit) of cross section 200 x 200 mm
concrete
102 Making connection of G.I. distribution branch with G.I. 18.13

main of following sizes by providing and fixing tee,
including cutting and threading the pipe etc. complete :
25 to 40 mm dia nominal bore 18.13.1 2.00 Each 636.73 1273.47
LANDSCAPING WORK

103 Supplying and stacking sludge at site including royalty DSR-2.3 37.50 CUM 266.45 9991.96
and carriage up to 5 km (sludge measured in stacks will
be reduced by 8% for payment).
104 Carrigae of sludge upto 5 K.M. DSR-1.1.3 50.00 CUM 169.97 8498.38
105 Supplying and stacking at site dump manure from DSR-2.4.3 12.50 CUM 289.93 3624.07
approved source including carriage upto 1 km (manure
measured in stacks will be reduced by 8% for payment)
: Screened through sieve of I.S. designation 4.75 mm
106 Mixing earth and sludge or manure in the required DSR-2.4.3 50.00 CUM 33.13 1656.26
proportion specified or directed by the Officer-in-
charge.
107 Spreading of sludge, dump manure or/and good earth DSR-2.8 50.00 CUM 47.44 2372.24
in required thickness (cost of sludge dump manure
or/and good earth to be paid separately).
108 Digging holes in ordinary soil and refilling the same

with the excavated earth mixed with manure or sludge
in the ratio of 2:1 by volume (2 parts of stacked volume
of earth after reduction by 20% : 1 part of stacked
volume of manure after reduction by 8%), flooding with
water, dressing, including removal of rubbish and
surplus earth, if any with all leads and lifts ( cost of
manure, sludge or extra good earth if needed to be paid
for separately).
Holes 0.9 m dia. and 0.90 m deep. DSR-2.14.2 5.00 NO. 129.69 648.46
Plantation of trees
109 Supply and stacking of Azadirachta indica (Neem) DSR-7.5 2.00 No. 58.91 117.82
plant of height 120- 130 cm. in big polybag of size 25
cm as per direction of the officer -in-
charge.
110 Supply and stacking of Cassia fistula (Amaltash) DSR-7.16 2.00 No. 58.91 117.82
plant of height 120-135 cm. in big polybag of size
25 cm as per direction of the officer -in-charge.
111 Supply and stacking of Ficus religiosa (Peepal) plant DSR-7.36 1.00 No. 58.91 58.91
of height 150-165 cm. in big polybag of size 30 cm
as per direction of the officer -in-charge.
112 Grassing with selection No.1 grass including watering DSR-2.10.2 250.00 Sqm 12.05 3013.45
and maintenance of the lawn for 30 days or more till the
grass forms a thick lawn, free from weeds and fit for
mowing including supplying good earth, if needed (the
good earth shall be paid for separately). With grass
Turf.
113 Providing and fixing M.S. flat iron tree guard 60 cm dia DSR-2.16 5.00 Each 4108.35 20541.74
and 2 m high, above ground consisting 4 nos 25 x 6 mm,
2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S.
flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in
two halves, fixing together at site with required six
numbers of 8 mm dia. and 30 mm long bolts, including
painting two coats with synthetic enamel paint of
approved brand and manufacture over a coat of primer.
One name plate of 1 mm thick M.S. sheet of size 250x100
mm shall be welded to the treeguard near the middle
height and lettered CPWD / PWD/ any other approved
name. The tree guard shall be suitably fixed to the
ground by embedding four legs of tree guard in pits of
suitable dia and to a depth of 25 cm, refilling the pits
with soil and ramming, complete in all respect as per
satisfaction and direction of Officer-in-charge.
114 COST OF SEPTIC TANK WITH SOAK PIT AR 1.00 Each 111860.60 111860.60
115 COST OF BORING AR 1.00 Each 109118.90 109118.90
116 COST OF APPROCH ROAD AR 391.00 SQM 1715.45 670742.12
117 COST OF INTERLOCKING AR 200.00 SQM 1715.45 343090.60
118 COST OF STONE SITTING BENCH MR 12.00 NOS. 19000.00 228000.00
119 COST OF SOLAR LIGHT MR 2.00 NOS. 33250.00 66500.00
MR 4.00 NOS. 20425.00 81700.00

120 COST OF RED SAND STONE DUSTBIN & BUCKET
121 ART WORK IN PILLAR MR 2.00 NOS. 256500.00 513000.00


SIGNAGE OF TREE SHAPED ART WORK IN R.C.C MR 2.00 NOS. 61750.00 123500.00
PILLAR (200 MM DIA) WITH M.S PIPE AND
122
HALLOW PIPE 50X50 MM , M.S SHEET 18 GAUGE
PAINTED WITH WOOD CLOURE.
123 COST OF PLAYING EQUIPMENT

(i) PARALLEL BARS 1.00 NOS. 33250.00 33250.00
(ii) MONKEY BAR SIMPLE 1.00 NOS. 55462.90 55462.90
(iv) SWING ECONOMY 1.00 NOS. 82632.90 82632.90
(vi) RABBIT RIDER 2.00 NOS. 23292.10 46584.20
(vii) SLIDING MODEL NO. 2 2.00 NOS. 42750.00 85500.00
(viii) FUN STN LOW COST MODEL -7 2.00 NOS. 37715.00 75430.00
124 COST OF DRINKING WATER SYSTEM 1.00 NOS. 90250.00 90250.00

TOTAL 75,38,251.80

Boqpdf

Uploaded by

Copyright:

Available Formats

Boqpdf

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boqpdf

Uploaded by

Copyright:

Available Formats

BILL OF QUANTITY

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

7 Providing and laying in position specified grade of 5.10

Above plinth to Floor-v level

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

11 Brick Work with common burnt clay ( non modular) 6.4.1

12 Steel reinforcement for R.C.C. work including 5.22.6

(a) Ground Floor 110.29 QTL 7530.63 830552.77

14 12mm cement plaster in single coat on fair side of single 13.4.2

(a) Ground Floor 142.74 SQM 239.95 34251.58

15 15 mm cement plaster on the rough side of single or half 13.5.2

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

20 Kota stone slabs 20 mm thick in risers of steps, skirting, 11.26.1

21 Supply and fixing 6 mm China white glazed tiles in 11.37

(a) Ground Floor 115.59 SQM 765.67 88504.08

23 Providing and fixing ISI marked flush door shutters

24 Mild steel or iron work of small sizes and sections such

(c) Angle iron chaukhat (40x40x5) 10.13.1 123.00 KG 98.94 12169.87

25 Fixing of Door, windows / ventilators chaukhats in MR

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

28 Painting with silicon & acrylic emulsion based water 13.60.1

29 Finishing walls (Two coats ) with exterior paint (Apex) 13.47.1

(a) Ground Floor 206.81 SQM 119.47 24707.65

30 Painting with silicon & acrylic emulsion based water 13.60.1

31 Providing and applying white cement based putty of 13.8

34 Providing and fixing aluminium tower bolts, ISI

300 x 10mm 9.97.1 7.00 NOS 90.84 635.90

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

36 Providing & laying "brick Coba" 12mm thick laid with

40 Ornamental Work 72.00 SQM 11827.50 851580.00

41 Birds 1.00 NO 42750.00 42750.00

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

49 Providing and fixing wash basin with C.I. brackets, 15

450 mm with a pair of 15 mm C.P. brass pillar tap.

51 Providing and fixing white vitreous china flat back half

Providing and fixing stone slab table rubbed, edges

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

56 Providing and fixing on wall face unplasticised Rigid

57 Supply and fixing of UPVC S.W.R. pipe type-B

59 Supply and fixing of UPVC S.W.R. plain bend

60 Supply and fixing of UPVC S.W.R. plain tee confirming

61 Supply and fixing of UPVC S.W.R. plain Y confirming to

62 Laying cement concrete 1:5:10 in haunching P.V.C./

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

64 Providing and fixing unplasticised -PVC pipe clips of

66 Providing and fixing Chlorinated Polyvinyl Chloride

67 Providing and fixing Chlorinated Polyvinyl Chloride

68 Providing & fixing CP brass bib cock of approved

69 Providing & fixing C.P. brass long body bib cock of

70 Providing and fixing gun metal gate valve with wheel of

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT

71 Providing and fixing ball valve (brass) of approved 18.18.3

72 Supply and hoisting of Sintex or equivalent high density New

74 Excavating trenches in all kind of soil of required width

75 Providing, laying and joining PVC/swr pipes grade 'A'

76 Laying cement concrete 1:2:4 in haunching P.V.C./ PWD 279a

77 Providing and fixing S.W. Gully trap grade 'A' complete

78 Constructing brick masonry manhole in cement mortar 19.7

S.N. DESCRIPTION OF ITEM DSR QTY UNIT RATE AMOUNT