0% found this document useful (0 votes)
34 views2 pages

Wavetek-148A Datasheet

Uploaded by

alexspetty
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
34 views2 pages

Wavetek-148A Datasheet

Uploaded by

alexspetty
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

®

MODEL 148A Advanced Test Equipment


FUNCTIONRentals
GENERATORS
E stablished 1981 www.atecorp.com 800-404-ATEC (2832)
20 MHz AM/FM/PM Generator
• Two Complete Generators
71T,M
.
• Internal or External AM, FM and
Phase Modulation
• 0.0002 Hz to 20 MHz, 30V Output
r • Sweep, Trigger and Gate
• 30 Volt Peak-to-Peak Output

Two Complete Generators mode ; frequency maybe modulated attenuator with vernier provides
Wavetek's Model 148AAM/FM/PM or swept to three decades ; and 80 dB of amplitude control . A vari-
Generator gives you a one instru- phase may be modulated a full plus able trigger level control accepts
ment source of modulated wave- or minus 50 degrees . main generator triggering signals
forms . It has two generators : a main from the modulation generator or
function generator, with full function trigger signals from an external
generator versatility, and a modula- Function Generator source .
tion generator, a convenient source The main generator generates from
for modulating and triggering 200 fcHz to 20 MHz in continuous, Generates Complex Waveforms
waveforms or a second, indepen- triggered and gated modes with a Main generator frequency, ampli-
dent signal source . 30V peak-to-peak maximum ampli- tude and triggering source are
tude . A unique overload LED indi- independently or simultaneously
Internal or External Modulation cates output clipping due to exces- controlled by the modulation
Modulation may be internal or exter- sive amplitude plus offset . Variable generator or external signal . The
nal in any combination . Amplitude symmetry and trigger stop/start con- model 148A can generate an
may be modulated from zero th rough trols provide additional special unlimited variety of complex
100% and in a suppressed carrier waveforms, and a four step waveforms .
MODEL 148A FUNCTION GENERATORS
VERSATILITY continuously adjustable from 1 :19 to r.~Sweep : 0 .2 Hz to 200 kHz
19 :1 . Varying symmetry provides (2 x setting) .
Instrument consists of a main Output (6009)
variable duty-cycle pulses, sawtooth
generator and a modulation generator '\, , '~, and I L are fixed level
ramps and nonsymmetrical sine wave .
which can be connected internally for 10 Vp-p . --rv1 and r- are fixed level
amplitude, frequency or phase NOTE: When SYMMETRY control is used
indicated frequency is divided by approxi- 0 to +5V (open circuit) .
modulated signals or for self-triggering Frequency Modulation (FM IN)
ately 10.
and tone burst signals . Voltage control of modulator fre-
Trigger and Gate
quency with sensitivity of 20% of
MAIN GENERATOR Input Range : 1V p-p to ±1OV .
rangelvolt . Input impedance is 5 k4 .
Impedance : 10 k4, 33 pF .
Waveforms
Pulse Width : 25 ns min .
Sine ', , triangle 'v , square "L , Repetition Rate : 10 MHz max . WAVEFORM CHARACTERISTICS
positive square rt. , negative square
Adjustable Triggered Signal Start/ Sine Distortion
v , TTL pulse and dc .
Stop Point: Approximately -90° to <5% .
Operational Modes +90° to 2 MHz . Time Symmetry
Continuous, external trigger and gate,
<1% from 1 Hz to 10 kHz .
and internal trigger and gate .
FREQUENCY PRECISION <5% from 0 .1 Hz to 100 kHz .
Modulation Modes
AM : Internal - waveform amplitude is Dial Accuracy
modulated from 0 to >100% . ± (1 % of setting + 1 % of full range) GENERAL
AM : External - AC signal gives sup- on x 100 thru x 1 M ranges . Stability
pressed carrier operation . ±(2% of setting + 2% of full range) Short Term : ± 0 .05% for 10 min .
FM : Internal modulation or external ac on X .01 thru x 10 and X IOM ranges . Long Term : ±0 .25% for 24 hr .
or do signal provides voltage control Time Symmetry Precentages apply to amplitude, fre-
off requency . Up to 1000 :1 frequency ± 0 .5% on x 100 thru x 10OK ranges quency and do offset .
change possible ; linear within limits of and from .2 0 to 2 .0 on dal . Environment
selected range . ±5% on all other ranges and from Specifications apply at 23° ±5°C .
Sweep : Ramp signal sweeps the main 0 .02 to 2 .0 on dial . Instrument will operate from 0° to
output signal frequency from low to +50°C ambient temperatures .
high or vice versa . frequency sweeps AMPLITUDE PRECISION Dimensions
to 1000 :1 within the selected range . Amplitude Change With Frequency 28 .6 cm (11 1/4 in .) wide ; 13 .3 cm
Internal ramp can be held at limits for Sine variation less than : (5'/4 in .) high ; 27 .3 cm (10 3/4 in .) deep .
precision upper and lower frequency ±0 .1 dB through x 10OK ranges,- Weight
setting . * 0 .5 dB on x 1 M range, 4 .5 kg (10 Ib) net ; 5 .9 kg (13 Ib)
PM : Internal or external modulation ± 3 dB on x 1 CM range . shipping .
signal causes instantaneous carrier Step Attenuator Accuracy Power
frequency shift proportional to rate of ±0 .3 dB per 20 dB step at 2 kHz . 90 to 105V, 108 to 126V, 198 to 231V
signal amplitude change, producing up and 216 to 252V selectable ; 48 to
to ±50° carrier phase shift . Enabled WAVEFORM CHARACTERISTICS 400 Hz ; less than 40 VA.
for main generator frequency range
Sine Distortion NOTE : Unless otherwise noted, all specifica-
x 100 and above . tions apply from 0.1 to 2.0 on frequency dial,
Frequency Range <0 .5 % on X 100 to X I OK ranges .
<1 .0 % on x 0 .01 to x 10 and x 100K when FUNCTION OUT is at maximum and 5052
0 .0002 Hz to 20 MHz in 10 overlapping terminated, with SYMMETRY control at OFF.
ranges with vernier . ranges .
Symmetry and vernier affect frequency calibra-
Function Output (5052) Alt harmonics 30 dB below fundamen- tion . Maximum possible asymmetry is a func-
A/ , 'v , ' L selectable and variable tal x 1 M range . tion of frequency setting .
to 30 Vp-p (15 Vp-p into 5052) . n , u All harmonics 26 dB below fundamen-
up to 15 Vp (7 .5 Vp into 50Q) . All wave- tal on x 1 OM range . FACTORYIFOB
forms and dc give 150 mA peak cur- Square Wave Rise/Fall Time
At FUNCTION OUT <25 ns for 15 Vp-p San Diego, CA
rent and attenuate to 60 dB in 20 dB
steps plus 20 dB continuous control . into 5052 load .
DC Output and DC Offset
Between ± 15 Vdc (+_ 7 .5 Vdc into MODULATION GENERATOR
50Q) with signal peak plus offset
limited to -±-15 Vdc (± 7 .5 Vdc into
504) .
Sync Output (TTL)
TTL level pulse which will drive 10 TTL
loads .
External Modulation Input
AM : Sensitivity of 3 Vp out/Vp (1 .5V
Modulation Generator
into 509) . Input impedance is >2 .5 kQ .
FM : Sensitivity of 20% of frequency
range/Vp . Input impedance is 5 kQ . Waveforms
PM : Sensitivity of 10° phase shift/Vp . Selectable ' i -i,-l and i .
Input impedance is 10 kQ . Frequency Range
Symmetry 'U , % , r : 0 .1 Hz to 100 kHz in
Symmetry of all waveform outputs is three 100 :1 ranges .

You might also like