Automotive Programmable Power Supplies

G1.7kW/3.4kW/5kW - Fast Response 20V/30V/40V Output Range

G1.7kW/3.4kW - Power Sink 20V/30V/40V/60V/100V Output Range
Programmable Power Supplies
Special models for automotive applications

TDK-Lambda’s series of programmable DC power supplies offer

a wide variety of integrated functions and features. Delivering
high power density and excellent reliability backed by a 5 year
warranty its the best solution for many different applications
in test & measurement and industrial control.

The Fast-Speed and Power Sink models include

features specifically for automotive requirements.

2 | |
 Fast-Speed Models are especially designed for automotive test
simulation and similar ATE applications where faster output dynamics are required.

Features
• Up-and down programming time T_rise < 1mS; T_fall < 2.5mS
Increased Dynamics – up to 35 times faster than standard version
• Lower Output capacitance
• 5 year warranty
• Safety standards: UL61010-1, CSA22.2 No.61010-1, IEC61010-1, EN61010-1

Applications
• Automotive Test Application
• Engine Control
• Powertrain Control (including hybrid drive
technologies and electric drives)
• Vehicle Dynamics (e.g.: HIL, ESP, damping control)
• Comfort Electronics
• Interior Systems
• Infotainment
• Noise Cancelation
• Diagnosis

* In order to use DC laboratory power supplies within the test for automotive electronics, it is necessary to simu-
late voltage transients according to DIN 40839.
* Characteristic curve DIN 40839. This battery voltage run occurs, when a car motor is started.

| |3
G+1.7kW-F - Fast Series Specifications
Unless otherwise noted, specifications are warranted over the ambient temperature of 10°C to 50°C
OUTPUT RATING 20-85-F 30-56-F 40-42-F
1.Rated output voltage (*1) V 20 30 40
2.Rated output current (*2) A 85 56 42
3.Rated output power W 1700 1680 1680
INPUT CHARACTERISTICS V 20 30 40
1.Input voltage/freq. (*3) --- 85~265Vac continuous, 47~63Hz, single phase.
2.Maximum input current at 100% load (at A 20/10
100Vac/200Vac)
3.Power Factor (Typ.) --- 0.99 @ 100Vac, 0.98 @ 200Vac, rated output power.
4.Efficiency (Typ. at 100Vac/200Vac)(*17) % 87/89
5.Inrush current (*5) --- Less than 50A.
CONSTANT VOLTAGE MODE V 20 30 40
1. Max. Line regulation (*6) --- 0.01% of rated output voltage.
2. Max. Load regulation (*7) --- 0.01% of rated output voltage +2mV.
3. Ripple and noise at 25°C ± 5°C (p-p, 20MHz) (*8) 100 130 120
mV
4. Ripple and noise (p-p, 20MHz) (*8) (*18) 150 250 200
5. Ripple r.m.s. at 25°C ± 5°C 5Hz~1MHz (*8) 15 25 15
mV
6. Ripple r.m.s. 5Hz~1MHz (*8) (*18) 25 40 30
7. Temperature coefficient --- 50PPM/OC from rated output voltage, following 30 minutes warm-up.
8. Temperature stability --- 0.01% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temperature.
9. Warm-up drift --- Less than 0.01% of rated output voltage +2mV over 30 minutes following power on.
10. Remote sense compensation/wire (*10) V 2 5 5
11. Up-prog. response time (*11) mS <1 <1 <1
12. Down-prog. response time (*12) Full load mS <2 <2 <2.5
No load <80 <100 <180
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated
13. Transient response time --- output current. Output set point: 10~100%, Local sense.
Less than 1mS for models up to and including 100V. 2mS for models above 100V.
14. Start-up delay --- Less than 6Sec.
15. Hold-up time --- 16mS Typical. Rated output power.
CONSTANT CURRENT MODE V 20 30 40
1.Max. Line regulation (*6) --- 0.01% of rated output current +2mA.
2.Max. Load regulation (*9) --- 0.02% of rated output current +5mA.
4. Ripple r.m.s. at 25°C ± 5°C. 5Hz~1MHz (*13) <450 <250 <70
mA
5. Ripple r.m.s. 5Hz~1MHz (*13) (*18) <750 <350 <100
6. Temperature coefficient --- 100PPM/OC from rated output current, following 30 minutes warm-up.
7. Temperature stability --- 0.01% of rated Iout over 8hrs. Interval following 30 minutes warm-up. Constant line, load & temperature.
8. Warm-up drift --- Less than +/-0.25% of rated output current over 30 minutes following power on.
ANALOG PROGRAMMING AND MONITORING (ISOLATED FROM THE OUTPUT)
1.Vout voltage programming --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.15% of rated Vout.
2.Iout voltage programming (*14) --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.4% of rated Iout.
3.Vout resistor programming --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
4.Iout resistor programming (*14) --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Iout.
5.Output voltage monitor --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Vout.
6.Output current monitor (*14) --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Iout.
SIGNALS AND CONTROLS (ISOLATED FROM THE OUTPUT)
Power supply output monitor. Open collector. Output On: On. Output Off: Off.
1.Power supply OK #1 signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
CV/CC Monitor. Open collector. CC mode: On. CV mode: Off. Maximum Voltage: 30V.
2.CV/CC signal --- Maximum Sink Current: 10mA.
Enable/Disable analog programming control by electrical signal or dry contact. Remote: 0~0.6V or short.
3.LOCAL/REMOTE Analog control --- Local: 2~30V or open.
Analog programming control monitor signal. Open collector. Remote: On. Local: Off.
4.LOCAL/REMOTE Analog signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
Enable/Disable PS output by electrical signal or dry contact.
5.ENABLE/DISABLE signal --- 0~0.6V or short, 2~30V or open. User selectable logic.
Enable/Disable PS output by electrical signal or dry contact.
6.INTERLOCK (ILC) control --- Output ON: 0~0.6V or short. Output OFF: 2~30V or open.
Two open drain programmable signals. Maximum voltage 25V. Maximum sink current 100mA
7.Programmed signals --- (shunted by 27V zener).
Maximum low level input voltage = 0.8V. Minimum high level input voltage = 2.5V.
8.TRIGGER IN / TRIGGER OUT signals --- Maximum high level input = 5V positive edge trigger: tw = 10us minimum. Tr, Tf = 1us maximum.
Min delay between 2 pulses 1ms.
9.DAISY_IN/SO control signal --- By electrical Voltage: 0~0.6V/2~30V or dry contact.
10.DAISY_OUT/PS_OK #2 signal --- 4~5V = OK, 0V (500Ω impedance) = Fail.
FUNCTIONS AND FEATURES
1.Parallel operation --- Not Applicable
2.Series operation --- Not Applicable
3.Daisy chain --- Power supplies can be connected in Daisy chain to synchronize their turn-on and turn-off.
Limits the output power to a programmed value. Programming via the communication ports or the front
4.Constant power control --- panel.
Emulates series resistance. Resistance range: 1~1000mΩ. Programming via the communication ports or the
5.Output resistance control --- front panel.
Programmable Output rise and Output fall slew rate.
6.Slew rate control --- Programming range: 0.0001~999.99 V/mS. or A/mS.
Programming via communication ports or front panel.

4
 Profiles of up to 100 steps can be stored in 4 memory cells.
7.Arbitrary waveforms --- Activation by command via communication ports or front panel.
8. Output capacitance --- G20-85-F: 4.23mF; G30-56-F: 1.96mF; G40-42-F: 1.56mF
PROGRAMMING AND READBACK (USB, LAN, RS232/485, Optional IEEE (*16) Interface)
V 20 30 40
1.Vout programming accuracy (*15) --- 0.05% of rated output voltage
2.Iout programming accuracy (*14) --- 0.1% of actual output current+0.2% of rated output current
3.Vout programming resolution --- 0.002% of rated output voltage
4.Iout programming resolution --- 0.002% of rated output current
5.Vout readback accuracy --- 0.05% of rated output voltage
6.Iout readback accuracy (*14) --- 0.2% of rated output current
% of rated
7.Vout readback resolution output 0.006% 0.004% 0.003%
voltage
% of rated
8.Iout readback resolution 0.002% 0.003% 0.003%
output current
PROTECTIVE FUNCTIONS
V 20 30 40
Output shut-down when power supply changes mode from CV or Power Limit to CC mode or from CC or
1.Foldback protection --- Power Limit to CV mode. User presetable. Reset by AC input recycle in autostart mode, by Power Switch, by
OUTPUT button, by rear panel or by communication.

2.Over-voltage protection (OVP) ---

Output shut-down. Reset by AC input recycle in autostart mode, by Power Switchm, by OUTPUT button, by
rear panel or by communication.
3.Over -voltage programming range V 1~24 2~36 2~44.1
4.Over-voltage programming accuracy --- +/-1% of rated output voltage
5.Output under voltage limit (UVL) ---
Prevents from adjusting Vout below limit. Does not apply in analog programming.
Preset by front panel or communication port.
6.Over temperature protection --- Shuts down the output. Auto recovery by autostart mode.
Prevents adjustment of Vout below limit. P.S output turns Off during under voltage condition.
7.Output under voltage protection (UVP) --- Reset by AC input recycle in autostart mode, by Power Switch, by OUTPUT button, by rear panel or by
communication.
FRONT PANEL
--- Multiple options with 2 Encoders.
--- Vout/Iout/Power Limit manual adjust.
--- OVP/UVL/UVP manual adjust.
--- Protection Functions - OVP, UVL, UVP, Foldback, OCL, ENA, ILC.
1.Control functions --- Communication Functions - Selection of LAN, RS232, RS485, USB or Optional communication interface.
--- Output ON/OFF. Front Panel Lock.
--- Communication Functions - Selection of Baud Rate, Address, IP and communication language.
--- Analog Control Functions - Selection Voltage/resistive programming 5V/10V, 5KΩ/10KΩ programming.
--- Analog Monitor Functions - Selection of Voltage/Current Monitoring 5V/10V.
--- Vout: 4 digits, accuracy: 0.05% of rated output voltage +/-1 count.
2.Display
--- Iout: 4 digits, accuracy: 0.2% of rated output current +/-1 count.
OUTPUT ON, ALARM, PREVIEW, FINE, COMMUNICATION, PROTECTION, CONFIGURATION, SYSTEM,
3.Front Panel Buttons Indications --- SEQUENCER.
Voltage, Current, Power, CV, CC, CP, External Voltage, External Current, Address, LFP, Autostart, Safestart,
4.Front Panel Display Indications --- Foldback V/I, Remote (communication), RS/USB/LAN/Optional communication interface, Trigger, Load/
Store Cell.
ENVIRONMENTAL CONDITIONS
1.Operating temperature --- 0~50OC, 100% load.
2.Storage temperature --- -30~85OC.
3.Operating humidity --- 20~90% RH (no condensation).
4.Storage humidity --- 10~95% RH (no condensation).
Operating: 10000ft (3000m), output current derating 2%/100m or Ta derating 1OC/100m above 2000m.
5.Altitude --- Non-operating: 40000ft (12000m).
MECHANICAL
1.Cooling --- Forced air-cooling by internal fans. Airflow direction: From front panel to power supply rear.
2.Weight Kg Less than 5Kg.
W: 423, H: 43.6, D: 441.5 (Without busbars and busbars cover), W: 423, H: 43.6, D: 553.2 (Including busbars
3.Dimensions (WxHxD) mm and busbars cover) (Refer to Outline drawing).
4.Vibration --- MIL-810G, method 514.6, Procedure I, test condition Annex C - 2.1.3.1
5.Shock --- Less than 20G, half sine, 11mS. Unit is unpacked.

5
SAFETY/EMC
1.Safety standards --- UL61010-1, CSA22.2 No.61010-1, IEC61010-1, EN61010-1
1.1.Interface classification --- Output, J1, J2, J3, J4, J5, J6, J7, J8 (sense) and J9 (communication options) are SELV.
1.2.Withstand voltage --- Input - Output (SELV): 4242VDC 1min, Input - Ground: 2835VDC 1min.
1.3.Isolation resistance --- >100Mohm at 25°C, 70%RH, Output to Ground 500VDC.
2.EMC standards (*4) --- IEC/EN61204-3 Industrial environment.
2.1.Conducted emission --- IEC/EN61204-3 Industrial environment, Annex H table H.1, FCC Part 15-A, VCCI-A.
2.2.Radiated emission --- IEC/EN61204-3 Industrial environment, Annex H table H.3 and H.4, FCC Part 15-A, VCCI-A.

NOTES:
*1: Minimum voltage is guaranteed to maximum 0.1% of rated output voltage.
*2: Minimum current is guaranteed to maximum 0.2% of rated output current.
*3: For cases where conformance to various safety standards (UL, IEC, etc…) is required, to be described as 100-240Vac (50/60Hz).
*4: Signal and control ports interface cables length: Less than 3m, DC output power port cables length: Less than 30m.
*5: Not including EMI filter inrush current, less than 0.2mS.
*6: 85~132Vac or 170~265Vac. Constant load.
*7: From No-Load to Full-Load, constant input voltage. Measured at the sensing point in Remote Sense.
*8: Measured with JEITA RC-9131C (1:1) probe.At low temperature (0~10°C) power supply needs 2min warm up.
*9: For load voltage change, equal to the unit voltage rating, constant input voltage.
*10: The maximum voltage on the power supply terminals must not exceed the rated voltage.
*11: From 10% to 90% of Rated Output Voltage, with rated, resistive load.
*12: From 90% to 10% of Rated Output Voltage.
*13: The ripple is measured at 10~100% of rated output voltage and rated output current. B.W 5Hz~1MHz.
*14: The Constant Current programming, readback and monitoring accuracy do not include the warm-up and Load regulation thermal drift.
*15: Measured at the sensing point.
*16: Maximum ambient temperature for IEEE option is 40°C.
*17: Tamb = 25°C, rated output power.
*18: At Tamb < 10°C the Output Ripple & Noise is higher, there is a need of 2min warm-up.
To achieve high-speed responed, the output capacitance has been reduced.
Due to smaller capacitance, the output ripple & noise is higher, but it’s not a problem for applications requiring high speed power supply as Automotive
industry.

6
G+3.4kW-F - Fast Series Specifications
Unless otherwise noted, specifications are warranted over the ambient temperature of 10°C to 50°C.
OUTPUT RATING 20-170-F 30-112-F 40-85-F
1.Rated output voltage (*1) V 20 30 40
2.Rated output current (*2) A 170 112 85
3.Rated output power W 3400 3360 3400
INPUT CHARACTERISTICS V 20 30 40
1.Input voltage/freq. 3-Phase, 3 wire+ground (*4) 3-Phase, 200V models: 170~265Vac, 47~63Hz (Covers 200/230Vac).
1-Phase, 2 wire+ground 3-Phase, 400V models: 342~460Vac, 47~63Hz (Covers 380/400/415Vac).
---
3-Phase, 480V models: 342~528Vac, 47~63Hz (Covers 380/400/415/440/460/480Vac).
1-Phase models: 170~265Vac, 47~63Hz (Covers 200/208/230/240).
3-Phase, 200V models 12.5A @ 200Vac.
2.Maximum input current at 3-Phase, 400V models 6.5A @ 380Vac.
---
100% load (*19) 3-Phase, 480V models 6.5A @ 380Vac.
1-Phase models 21A @ 200Vac.
For 3-Phase: 0.94 @ 200/380Vac, rated output power.
3.Power Factor (Typ.) ---
For 1-Phase: 0.99 @ 200Vac, rated output power.
4.Efficiency (Typ.) (*5) (*20) % 89 89.5 90
5.Inrush current (*6) --- Less than 50A.
CONSTANT VOLTAGE MODE V 20 30 40
1. Max. Line regulation (*7) --- 0.01% of rated output voltage.
2. Max. Load regulation (*8) --- 0.01% of rated output voltage +5mV.
3. Ripple & Noise 3-Phase (p-p, 20MHz) (*9) (*20) mV 100 160 150
4. Ripple & Noise 1-Phase (p-p, 20MHz) (*9) (*20) mV 120 250 180
5. Ripple r.m.s. 5Hz~1MHz for 3-Phase (*9) (*20) mV 12 25 15
6. Ripple r.m.s. 5Hz~1MHz for 1-Phase (*9) (*20) mV 15 25 20
7.Temperature coefficient --- 50PPM/ C from rated output voltage, following 30 minutes warm-up.
O

8.Temperature stability --- 0.01% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temperature.
9.Warm-up drift --- Less than 0.05% of rated output voltage +2mV over 30 minutes following power on.
10.Remote sense compensation/wire (*10) V 2 5 5
11.Up-prog. response time (*11) mS <1 <1 <1
Full load (*11) <1.3 <1.3 <1.3
12.Down-prog. response time mS
No load (*12) <120 <140 <160
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated
13.Transient response time --- output current. Output set point: 10~100%, Local sense.
Less than 1mS for models up to and including 100V.
14.Start-up delay --- Less than 6Sec.
15.Hold-up time --- For 3-Phase: 7mS Typical, rated output power. For 1-Phase: 10mS Typical, rated output power.
CONSTANT CURRENT MODE V 20 30 40
1.Max. Line regulation (*7) --- 0.05% of rated output current.
2.Max. Load regulation (*13) --- 0.08% of rated output current.
3.Ripple r.m.s. 5Hz~1MHz for 3-Phase (*14) (*20) mA <600 <400 <200
4.1. Ripple r.m.s. 5Hz~1MHz for 1-Phase (*14) (*20) mA <800 <400 <400
5.Temperature coefficient --- 10V~100V models: 100PPM/ C from rated output current, following 30 minutes warm-up.
O

6.Temperature stability --- 0.01% of rated Iout over 8hrs. interval following 30 minutes warm-up. Constant line, load & temperature.
7.Warm-up drift --- 10V~100V models: Less than +/-0.25% of rated output current over 30 minutes following power on.
ANALOG PROGRAMMING AND MONITORING (ISOLATED FROM THE OUTPUT)
1.Vout voltage programming --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.15% of rated Vout.
2.Iout voltage programming (*15) --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.4% of rated Iout.
3.Vout resistor programming --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
4.Iout resistor programming (*15) --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Iout.
5.Output voltage monitor --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Vout.
6.Output current monitor (*15) --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Iout.
SIGNALS AND CONTROLS (ISOLATED FROM THE OUTPUT)
Power supply output monitor. Open collector. Output On: On. Output Off: Off.
1.Power supply OK #1 signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
CV/CC Monitor. Open collector. CC mode: On. CV mode: Off. Maximum Voltage: 30V.
2.CV/CC signal --- Maximum Sink Current: 10mA.
Enable/Disable analog programming control by electrical signal or dry contact. Remote: 0~0.6V or
3.LOCAL/REMOTE Analog control --- short. Local: 2~30V or open.
Analog programming control monitor signal. Open collector. Remote: On. Local: Off.
4.LOCAL/REMOTE Analog signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
Enable/Disable PS output by electrical signal or dry contact.
5.ENABLE/DISABLE signal --- 0~0.6V or short, 2~30V or open. User selectable logic.
Enable/Disable PS output by electrical signal or dry contact.
6.INTERLOCK (ILC) control --- Output ON: 0~0.6V or short. Output OFF: 2~30V or open.
Two open drain programmable signals. Maximum voltage 25V. Maximum sink current 100mA
7.Programmed signals --- (shunted by 27V zener).
Maximum low level input voltage = 0.8V. Minimum high level input voltage = 2.5V.
8.TRIGGER IN / TRIGGER OUT signals --- Maximum high level input = 5V positive edge trigger: tw = 10us minimum. Tr,Tf = 1us maximum.
Min delay between 2 pulses 1ms.
9.DAISY_IN/SO control signal --- By electrical Voltage: 0~0.6V/2~30V or dry contact.
10.DAISY_OUT/PS_OK #2 signal --- 4~5V = OK, 0V (500Ω impedance) = Fail.

7
FUNCTIONS AND FEATURES
1.Parallel operation --- Not Applicable
2.Series operation --- Not Applicable
3.Daisy chain --- Power supplies can be connected in Daisy chain to synchronize their turn-on and turn-off.
4.Constant power control --- Limits the output power to a programmed value. Programming via the communication ports or the
front panel.
5.Output resistance control --- Emulates series resistance. Resistance range: 1~1000mΩ. Programming via the communication ports
or the front panel.
6.Slew rate control Programmable Output rise and Output fall slew rate.
--- Programming range: 0.0001~999.99 V/mS. or A/mS.
Programming via communication ports or front panel.
7.Arbitrary waveforms --- Profiles of up to 100 steps can be stored in 4 memory cells.
Activation by command via communication ports or front panel.
8. Output capacitance: --- G20-170-F: 6.11mF; G30-112-F: 2.84mF; G40-85-F: 2.16mF

PROGRAMMING AND READBACK (USB, LAN, RS232/485, Optional (*18) Interfaces)

V 20 30 40
1.Vout programming accuracy (*16) --- 0.05% of rated output voltage.
2.Iout programming accuracy (*15) --- 0.1% of actual output current+0.2% of rated output current.
3.Vout programming resolution --- 0.002% of rated output voltage.
4.Iout programming resolution --- 0.002% of rated output current.
5.Vout readback accuracy --- 0.05% of rated output voltage.
6.Iout readback accuracy (*15) --- 0.2% of rated output current.
7.Vout readback resolution % of rated
output 0.006% 0.004% 0.003%
voltage
8.Iout readback resolution % of rated
output 0.007% 0.010% 0.002%
current

PROTECTIVE FUNCTIONS
V 20 30 40
1.Foldback protection Output shut-down when power supply changes mode from CV or Power Limit to CC mode or from CC
--- or Power Limit to CV mode. User presetable. Reset by AC input recycle in autostart mode, by Power
Switch, by OUTPUT button, by rear panel or by communication.
2.Over-voltage protection (OVP) Output shut-down. Reset by AC input recycle in autostart mode, by Power Switch, by OUTPUT button,
--- by rear panel or by communication.
3.Over -voltage programming range V 1~24 2~36 2~4.1
4.Over-voltage programming accuracy --- +/-1% of rated output voltage
5.Output under voltage limit (UVL) Prevents from adjusting Vout below limit. Does not apply in analog programming.
--- Preset by front panel or communication port.
6.Over temperature protection --- Shuts down the output. Auto recovery by autostart mode.
7.Output under voltage protection (UVP) Prevents adjustment of Vout below limit. P.S output turns Off during under voltage condition.
--- Reset by AC input recycle in autostart mode, by Power Switch, by OUTPUT button, by rear panel or by
communication.

FRONT PANEL
1.Control functions --- Multiple options with 2 Encoders.
--- Vout/Iout/Power Limit manual adjust.
--- OVP/UVL/UVP manual adjust.
--- Protection Functions - OVP, UVL, UVP, Foldback, OCL, ENA, ILC.
--- Communication Functions - Selection of LAN, RS232, RS485, USB or Optional communication interface.
--- Output ON/OFF. Front Panel Lock.
--- Communication Functions - Selection of Baud Rate, Address, IP and communication language.
--- Analog Control Functions - Selection Voltage/resistive programming 5V/10V, 5KΩ/10KΩ programming.
--- Analog Monitor Functions - Selection of Voltage/Current Monitoring 5V/10V.
2.Display --- Vout: 4 digits, accuracy: 0.05% of rated output voltage +/-1 count.
--- Iout: 4 digits, accuracy: 0.2% of rated output current +/-1 count.
3.Front Panel Buttons Indications OUTPUT ON, ALARM, PREVIEW, FINE, COMMUNICATION, PROTECTION, CONFIGURATION, SYSTEM,
---
SEQUENCER.
4.Front Panel Display Indications Voltage, Current, Power, CV, CC, CP, External Voltage, External Current, Address, LFP, Autostart,
--- Safestart, Foldback V/I, Remote (communication), RS/USB/LAN/Optional communication interface,
Trigger, Load/Store Cell.
ENVIRONMENTAL CONDITIONS
1.Operating temperature --- 0~50OC, 100% load.
2.Storage temperature --- -30~85OC.
3.Operating humidity --- 20~90% RH (no condensation).
4.Storage humidity --- 10~95% RH (no condensation).
5.Altitude Operating: 10000ft (3000m), output current derating 2%/100m or Ta derating 1OC/100m above
--- 2000m.
Non-operating: 40000ft (12000m).

8
MECHANICAL
1.Cooling --- Forced air cooling by internal fans. Airflow direction: From front panel to power supply rear.
2.Weight Kg Less than 6.25Kg.
3.Dimensions (WxHxD) W: 423, H: 43.6, D: 441.5 (Without busbars and busbars cover), W: 423, H: 43.6, D: 553.2 (Including
mm busbars and busbars cover) (Refer to Outline drawing).
4.Vibration --- MIL-810G, method 514.6, Procedure I, test condition Annex C - 2.1.3.1
5.Shock --- Less than 20G, half sine, 11mS. Unit is unpacked.

SAFETY/EMC
1.Safety standards --- UL61010-1, CSA22.2 No.61010-1, IEC61010-1, EN61010-1.
1.1.Interface classification Vout≤40V Models: Output, J1, J2, J3, J4, J5, J6, J7, J8 (sense) and J9 (communication options) are SELV.
--- 60≤Vout≤600V Models: Output and J8 (sense) are hazardous, J1, J2, J3, J4, J5, J6, J7 and J9
(communication options) are SELV.
1.2.Withstand voltage --- Vout≤40V Models: Input - Output (SELV): 4242VDC 1min, Input - Ground: 2835VDC 1min.
1.3.Isolation resistance --- >100Mohm at 25°C, 70%RH, Output to Ground 500VDC.
2.EMC standards (*17) --- IEC/EN61204-3 Industrial environment.
2.1.Conducted emission --- IEC/EN61204-3 Industrial environment, Annex H table H.1, FCC Part 15-A, VCCI-A.
2.2.Radiated emission --- IEC/EN61204-3 Industrial environment, Annex H table H.3 and H.4, FCC Part 15-A, VCCI-A.

NOTES:
*1: Minimum voltage is guaranteed to maximum 0.1% of rated output voltage.
*2: Minimum current is guaranteed to maximum 0.2% of rated output current.
*3: Derate 4A/1°C above 40°C.
*4: For cases where conformance to various safety standards (UL, IEC, etc…) is required, to be described as 190-240Vac (50/60Hz) for 3-Phase 200V models,380~415Vac
(50/60Hz) for 3-Phase 400V models, 380~480Vac (50/60Hz) for 3-Phase 480V models and 190-240Vac (50/60Hz) for 1-Phase models.
*5: 3-Phase 200V models: At 200Vac input voltage, 3-Phase 400/480V models: At 380Vac input voltage, 1-Phase models: At 200Vac input voltage.
At rated output power.
*6: Not including EMI filter inrush current, less than 0.2mS.
*7: 3-Phase 200V models: 170~265Vac, 3-Phase 400V models: 342~460Vac, 3-Phase 480V models: 342~528Vac, 1-Phase models: 170~265Vac. Constant load.
*8: From No-Load to Full-Load, constant input voltage. Measured at the sensing point in Remote Sense.
*9: For 10V~150V models: Measured with JEITA RC-9131C (1: 1) probe. For 300~600V models: Measured with 100: 1 probe.
*10: The maximum voltage on the power supply terminals must not exceed the rated voltage.
*11: From 10% to 90% of Rated Output Voltage at rated resistive load.
*12: From 90% to 10% of Rated Output Voltage.
*13: For load voltage change, equal to the unit voltage rating, constant input voltage.
*14: The ripple is measured at 10~100% of rated output voltage and rated output current. B.W 5Hz~1MHz.
*15: The Constant Current programming, readback and monitoring accuracy do not include the warm-up and Load regulation thermal drift.
*16: Measured at the sensing point.
*17: Signal and control ports interface cables length: Less than 3m, DC output power port cables length: Less than 30m.
*18: Maximum ambient temperature for IEEE option is 40°C.
*19: Typ. at Ta=25°C, rated output power.
*20: At Tamb < 10°C the Output Ripple & Noise is higher, there is a need of 2min warm-up.
To achieve high-speed respond, the output capacitance has been reduced.
Due to smaller capacitance, the output ripple & noise is higher, but it’s not a problem for applications requiring high speed power supply as Automotive
industry

9
G+5kW-F – Fast Series Specifications
Unless otherwise noted, specifications are warranted over the ambient temperature of 10°C to 50°C.
OUTPUT RATING 20-250-F 30-170-F 40-125-F
1. Rated output voltage (*1) V 20 30 40
2. Rated output current (*2) A 250 170 125
3. Rated output power W 5000 5100 5000

INPUT CHARACTERISTICS V 20 30 40
--- 3-Phase, 200V models: 170~265Vac, 47~63Hz (Covers 200/230Vac).
1. Input voltage/freq. 3 phase, 3 wire+ground (*3) 3-Phase, 400V models: 342~460Vac, 47~63Hz (Covers 380/400/415Vac).
3-Phase, 480V models: 342~528Vac, 47~63Hz (Covers 380/400/415/440/460/480Vac).
3-Phase, 200V models: 17.5A @ 200Vac.
2. Maximum Input 3-Phase, 400V models: --- 9.2A @ 380Vac.
current at 100% load
3-Phase, 480V models: 9.2A @ 380Vac.
3. Power Factor (Typ. ) --- 0.94 @ 200/380Vac, rated output power.
4. Efficiency (Typ. ) (*4) (*18) % 91 91 91
5. Inrush current (*5) --- Less than 50A.

CONSTANT VOLTAGE MODE V 20 30 40

1. Max. Line regulation (*6) --- 0.01% of rated output voltage.
2. Max. Load regulation (*7) --- 0.01% of rated output voltage +5mV.
3. Ripple & noise (p-p, 20MHz) (*8) (*19) mV 100 200 100
4. Ripple r.m.s. 5Hz~1MHz (*8) (*19) mV 15 15 10
5. Temperature coefficient --- 50PPM/OC from rated output voltage, following 30 minutes warm-up.
6. Temperature stability --- 0.01% of rated Vout over 8hrs. interval following 30 minutes warm-up. Constant line, load & temperature.
7. Warm-up drift --- Less than 0.05% of rated output voltage +2mV over 30 minutes following power on.
8. Remote sense compensation/wire (*9) V 2 5 5
9. Up-prog. response time (*10) mS <1 <1 <1
10. Down-prog. Full load (*10) <1 <1.5 <2
mS
response time No load (*11) <100 <120 <140
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated output current.
11.Transient response time --- Output set point: 10~100%, Local sense.
Less than 1mS for models up to and including 100V. 2mS for models above 100V.
12.Start-up delay --- Less than 5Sec.
13.Hold-up time --- 5mS Typical. Rated output power.

CONSTANT CURRENT MODE V 20 30 40

1. Max. Line regulation (*6) --- 0.05% of rated output current.
2. Max. Load regulation (*12) --- 0.08% of rated output current.
3. Ripple r.m.s. 5Hz~1MHz (*13) (*19) mA <850 <350 <250
4. Temperature coefficient --- 100PPM/OC from rated output current, following 30 minutes warm-up.
5. Temperature stability --- 0.01% of rated Iout over 8hrs. interval following 30 minutes warm-up. Constant line, load & temperature.
6. Warm-up drift --- Less than +/-0.25% of rated output current over 30 minutes following power on.

ANALOG PROGRAMMING AND MONITORING (ISOLATED FROM THE OUTPUT)

1. Vout voltage programming --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.15% of rated Vout.
2. Iout voltage programming (*14) --- 0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.4% of rated Iout.
3. Vout resistor programming --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
4. Iout resistor programming (*14) --- 0~100%, 0~5/10KΩ full scale, user selectable. Accuracy and linearity: +/-0.5% of rated Iout.
5. Output voltage monitor --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Vout.
6. Output current monitor (*14) --- 0~5V or 0~10V, user selectable. Accuracy: +/-0.5% of rated Iout.

10
SIGNALS AND CONTROLS (ISOLATED FROM THE OUTPUT)
Power supply output monitor. Open collector. Output On: On. Output Off: Off.
1. Power supply OK #1 signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
CV/CC Monitor. Open collector. CC mode: On. CV mode: Off. Maximum Voltage: 30V.
2. CV/CC signal --- Maximum Sink Current: 10mA.
Enable/Disable analog programming control by electrical signal or dry contact.
3. LOCAL/REMOTE Analog control --- Remote: 0~0.6V or short. Local: 2~30V or open.
Analog programming control monitor signal. Open collector. Remote: On. Local: Off.
4. LOCAL/REMOTE Analog signal --- Maximum Voltage: 30V. Maximum Sink Current: 10mA.
Enable/Disable PS output by electrical signal or dry contact.
5. ENABLE/DISABLE signal --- 0~0.6V or short, 2~30V or open. User selectable logic.
Enable/Disable PS output by electrical signal or dry contact.
6. INTERLOCK (ILC) control --- Output ON: 0~0.6V or short. Output OFF: 2~30V or open.
Two open drain programmable signals. Maximum voltage 25V. Maximum sink current 100mA
7. Programmed signals --- (shunted by 27V zener).
Maximum low level input voltage = 0.8V. Minimum high level input voltage = 2.5V.
8. TRIGGER IN / TRIGGER OUT signals --- Maximum high level input = 5V positive edge trigger: tw = 10us minimum. Tr,Tf = 1us maximum.
Min delay between 2 pulses 1ms.
9. DAISY_IN/SO control signal --- By electrical Voltage: 0~0.6V/2~30V or dry contact.
10. DAISY_OUT/PS_OK #2 signal --- 4~5V = OK, 0V (500Ω impedance) = Fail.

FUNCTIONS AND FEATURES

1. Parallel operation --- Not Applicable
2. Series operation --- Not Applicable
3. Daisy chain --- Power supplies can be connected in Daisy chain to synchronize their turn-on and turn-off.
Limits the output power to a programmed value. Programming via the communication ports or the front
4. Constant power control --- panel.
Emulates series resistance. Resistance range: 1~1000mΩ. Programming via communication ports or front
5. Output resistance control --- panel.
Programmable Output rise and Output fall slew rate.
6. Slew rate control --- Programming range: 0.0001~999.99 V/mS. or A/mS.
Programming via communication ports or front panel.
Profiles of up to 100 steps can be stored in 4 memory cells.
7. Arbitrary waveforms --- Activation by command via communication ports or front panel.
8. Output capacitance: --- G20-250-F: 8.0mF; G30-170-F: 3.72mF; G40-125-F: 2.76mF

PROGRAMMING AND READBACK (USB, LAN, RS232/485, Optional (*17) Interfaces)

V 20 30 40
1. Vout programming accuracy (*15) --- 0.05% of rated output voltage.
2. Iout programming accuracy (*14) --- 0.1% of actual output current +0.2% of rated output current.
3. Vout programming resolution --- 0.002% of rated output voltage.
4. Iout programming resolution --- 0.002% of rated output current.
5. Vout readback accuracy --- 0.05% of rated output voltage.
6. Iout readback accuracy (*14) --- 0.2% of rated output current.
% of rated
7. Vout readback resolution output 0.006% 0.004% 0.003%
voltage
% of rated
8. Iout readback resolution output 0.005% 0.006% 0.009%
current

PROTECTIVE FUNCTIONS V 20 30 40
Output shut-down when power supply changes mode from CV or Power Limit to CC mode or from CC or
1. Foldback protection --- Power Limit to CV mode. User presetable. Reset by AC input recycle in autostart mode, by Power Switch, by
OUTPUT button, by rear panel or by communication.
Output shut-down. Reset by AC input recycle in autostart mode, by Power Switch, by OUTPUT button, by rear
2. Over-voltage protection (OVP) --- panel or by communication.
3. Over-voltage programming range V 1~24 2~36 2~44.1
4. Over-voltage programming accuracy --- +/-1% of rated output voltage.
Prevents from adjusting Vout below limit. Does not apply in analog programming.
5. Output under voltage limit (UVL) --- Preset by front panel or communication port.
6. Over temperature protection --- Shuts down the output. Auto recovery by autostart mode.
Prevents adjustment of Vout below limit. P.S output turns Off during under voltage condition.
7. Output under voltage protection (UVP) --- Reset by AC input recycle in autostart mode, by Power Switch, by OUTPUT button, by rear panel or by
communication.

11
FRONT PANEL
1.Control functions --- Multiple options with 2 Encoders.
--- Vout/Iout/Power Limit manual adjust.
--- OVP/UVL/UVP manual adjust.
--- Protection Functions - OVP, UVL, UVP, Foldback, OCL, ENA, ILC.
--- Communication Functions - Selection of LAN, RS232, RS485, USB or Optional communication interface.
--- Output ON/OFF. Front Panel Lock.
--- Communication Functions - Selection of Baud Rate, Address, IP and communication language.
--- Analog Control Functions - Selection Voltage/resistive programming 5V/10V, 5KΩ/10KΩ programming.
--- Analog Monitor Functions - Selection of Voltage/Current Monitoring 5V/10V.
2.Display --- Vout: 4 digits, accuracy: 0.05% of rated output voltage +/-1 count.
--- Iout: 4 digits, accuracy: 0.2% of rated output current +/-1 count.
3.Front Panel Buttons Indications --- OUTPUT ON, ALARM, PREVIEW, FINE, COMMUNICATION, PROTECTION, CONFIGURATION, SYSTEM, SEQUENCER.
4.Front Panel Display Indications Voltage, Current, Power, CV, CC, CP, External Voltage, External Current, Address, LFP Autostart, Safetstart,
--- Foldback V/I, Remote (communication), RS/USB/LAN/Optional communication interface, Trigger, Load/Store
Cell.
ENVIRONMENTAL CONDITIONS
1.Operating temperature (*19) --- 0~50OC, 100% load.
2.Storage temperature --- -30~85OC.
3.Operating humidity --- 20~90% RH (no condensation).
4.Storage humidity --- 10~95% RH (no condensation).
5.Altitude Operating: 10000ft (3000m), output current derating 2%/100m or Ta derating 1OC/100m above 2000m.
--- Non-operating: 40000ft (12000m).
MECHANICAL
1.Cooling --- Forced air cooling by internal fans. Airflow direction: From front panel to power supply rear.
2.Weight Kg Less than 7.5Kg.
3.Dimensions (WxHxD) W: 423, H: 43.6, D: 441.5 (Without busbars and busbars cover), W: 423, H: 43.6, D: 553.2 (Including busbars and
mm busbars cover). Refer to Outline drawing.
4.Vibration --- MIL-810G, method 514.6, Procedure I, test condition Annex C - 2.1.3.1
5.Shock --- Less than 20G, half sine, 11mS. Unit is unpacked.

SAFETY/EMC
1.Safety standards --- UL61010-1, CSA22.2 No.61010-1, IEC61010-1, EN61010-1.
1.1.Interface classification --- Output, J1, J2, J3, J4, J5, J6, J7, J8 (sense) & J9 (communication options) are Non Hazardous.
Input – Output & J8 (sense), J1, J2, J3, J4, J5, J6, J7 & J9 (communication options): 4242VDC 1min,
1.2.Withstand voltage --- Input - Ground: 2835VDC 1min.
1.3.Isolation resistance --- >100Mohm at 25°C, 70%RH, Output to Ground 500VDC.
2.EMC standards (*16) --- IEC/EN61204-3 Industrial environment.
2.1.Conducted emission --- IEC/EN61204-3 Industrial environment, Annex H table H.1, FCC Part 15-A, VCCI-A.
2.2.Radiated emission --- IEC/EN61204-3 Industrial environment, Annex H table H.3 and H.4, FCC Part 15-A, VCCI-A.

12
NOTES:
*1: Minimum voltage is guaranteed to maximum 0.1% of rated output voltage.
*2: Minimum current is guaranteed to maximum 0.2% of rated output current.
*3: For cases where conformance to various safety standards (UL, IEC, etc…) is required, to be described as 190-240Vac (50/60Hz) for 3-Phase 200V models
380~415Vac (50/60Hz) for 3-Phase 400V models and 380~480Vac (50/60Hz) for 3-Phase 480V models.
*4: 3-Phase 200V models: At 200Vac input voltage, 3-Phase 400/480V: At 380Vac input voltage. With rated output power.
*5: Not including EMI filter inrush current, less than 0.2mS.
*6: 3-Phase 200V models: 170~265Vac, 3-Phase 400V models: 342~460Vac, 3-Phase 480V models: 342~528Vac. Constant load.
*7: From No-Load to Full-Load, constant input voltage. Measured at the sensing point in Remote Sense.
*8: Measured with JEITA RC-9131C (1:1) probe.
*9: The maximum voltage on the power supply terminals must not exceed the rated voltage.
*10: From 10% to 90% of Rated Output Voltage at rated resistive load.
*11: From 90% to 10% of Rated Output Voltage.
*12: For load voltage change, equal to the unit voltage rating, constant input voltage.
*13: The Ripple is measured at 10~100% of rated output voltage and rated output current. B.W 5Hz~1MHz.
*14: The Constant Current programming, readback and monitoring accuracy do not include the warm-up and Load regulation thermal drift.
*15: Measured at the sensing point.
*16: Signal and control ports interface cables length: Less than 3m, DC output power port cables length: Less than 30m.
*17: Max. ambient temperature for IEEE is 40°C.
*18: Typ. at Ta=25°C, rated output power.
*19: At Tamb < 10°C the Output Ripple & Noise is higher, there is a need of 2min warm-up.
To a c h i e ve h i g h - s p e e d r e s p o n d , t h e o u t p u t c a p a c i t a n ce h a s b e e n r e d u ce d .
Due to smaller capacitance, the output ripple & noise is higher, but it's not a problem for applications requiring high speed power supply as Automotive
inustry

13
How to order G1.7kW FAST - Power Supply Identification / Accessories
G 20 - 85 - F - -
Series Name Output Output FAST Interface Options Accessories Options
Front Panel Type Voltage Current M - Printed *User Manual
Empty: standard (0~20V) (0~85A) * User Manual & GUI are
available on the website
B: Blank Front Panel (ATE version) P - Bus Parralleling Cable

AC Inputs (All Models)

1Ø, 85 ~ 265Vac
Interface Options (Factory installed) P/N
LAN ( 1.5 compliant with Multi-Drop capability)- built-in -
USB 2.0 compliant with Multi-Drop capability - built-in -
RS-232/RS-485 - built-in -
Isolated Analog Program/Monitor Interface
(5V/10V Pgm/Mon with 600V isolation) - built-in -
IEEE (488.2 & SCPI compliant with Multi-Drop capability installed) IEEE
Modbus-TCP MDBS
EtherCAT ECAT

Models 1.7kW
Model Voltage (V) Current (A) Power (W)
G20-85-F 0~20V 0~85 1700
G30-56-F 0~30V 0~56 1680
G40-42-F 0~40V 0~42 1680

Accessories
Accessories will be sent separately from the Power Supply packing, according to order.
1. Serial Communication cable. RS-232/RS-485 cable is used to connect the power supply to the Host PC.
Mode RS-485 RS-232
PC Connector, Communication Cable, Power Supply Connector DB-9F. Shielded L=2m. RJ-45 DB-9F. Shielded L=2m, RJ-45
P/N GEN/485-9 GEN/232-9
2. Serial link cable (Included with the power supply)
Daisy-chain up to 31 ™ power supplies.
Mode Power Supply Connector Communication Cable P/N
RS-485 RJ-45 Shielded L=50cm GEN/RJ45

3. Bus Paralleling cable

Connectors Cables P/N
2013595-1 (TYCO) Shielded L=11cm G/P
4. User Manual
Printed User Manual G/M

14
How to order G3.4kW / 5kW-FAST - Power Supply Identification / Accessories
G 20 - 170 - F - - -
Series Name Output Output FAST Interface Options AC Input Options Accessories Options
Front Panel Type Voltage Current 3.4kW-1P208 (1Ø 170~265VAC) M - Printed *User Manual
Empty: standard (0~20V) (0~170A) 3.4kW/5kW-3P208 (3Ø 170~265VAC) * User Manual & GUI are
B: Blank Front Panel (ATE version) 3.4kW/5kW 3P400 (3Ø 342~460VAC) available on the website

3.4kW/5kW 3P480 (3Ø 342~528VAC) P - Bus Parralleling Cable

Interface Options (Factory installed) P/N

LAN ( 1.5 compliant with Multi-Drop capability)- -
built-in
USB 2.0 compliant with Multi-Drop capability - built-in -
RS-232/RS-485 - built-in -
Isolated Analog Program/Monitor Interface
-
(5V/10V Pgm/Mon with 600V isolation) - built-in
IEEE (488.2 & SCPI compliant with Multi-Drop capability IEEE
installed)
Modbus-TCP MDBS
EtherCAT ECAT

Models G3.4kW Models G5kW

Model Output Output Output Model Output Output Output
Voltage VDC Current (A) Power (W) Voltage VDC Current (A) Power (W)
G20-170-F 0~20V 0~170 3400 G20-250-F 0~20V 0~250 5000
G30-112-F 0~30V 0~112 3360 G30-170-F 0~30V 0~170 5100
G40-85-F 0~40V 0~85 3400 G40-125-F 0~40V 0~125 5000

Accessories
Accessories will be sent separately from the Power Supply packing, according to order.
1. Serial Communication cable. RS-232/RS-485 cable is used to connect the power supply to the Host PC.
Mode RS-485 RS-232
PC Connector, Communication Cable, Power Supply Connector DB-9F. Shielded L=2m. RJ-45 DB-9F. Shielded L=2m, RJ-45
P/N GEN/485-9 GEN/232-9
2. Serial link cable (Included with the power supply)
Daisy-chain up to 31 ™ power supplies.
Mode Power Supply Connector Communication Cable P/N
RS-485 RJ-45 Shielded L=50cm GEN/RJ45
3. Bus Paralleling cable
Connectors Cables P/N
2013595-1 (TYCO) Shielded L=11cm G/P
4. User Manual
Printed User Manual G/M

15
 1.7kW/3.4kW models with a Power Sink Option (PSINK)
can absorb energy from the load.

Features
• Maintains output voltage setting
regardless of whether output power
is positive or negative (source and sink)
• Can absorb 300 W peak power
• Absorb 100W continues power
• The Power Sink module also allows for a faster response time
when power supply is programmed to a lower output voltage.
• 5 year warranty

Applications
• Ideal solution for testing electric motors
with PWM-speed control. These systems often return
power to the power supply during braking conditions.
• ATE systems requiring fast down programming
at no load conditions.
• Testing capacitors and batteries.
• Automotive Motor Test eg. power window drives,
mirror and seat adjustment.

16
 with Power Sink Options

The Power Sink module absorbs power that is feedback to the unit.

Electrical energy Kinetic energy

Current

Torque
Phase 1 – Power supply delivers
the electrical energy and the motor
transform this electrical energy to
kinetic energy to the load. Motor is
Motor Rotation
running in constant speed.

Electrical energy Kinetic energy

Current
Output
Voltage
Increaee
Phase 2 – Motor is braking, the Torque
excess kinetic energy from the load
is returned to the power supply.
This excess energy is charging the
power supply output capacitance Motor Rotation
and rises the output voltage.
Electrical energy Kinetic energy

Phase 3 – Control circuit senses that PSINK Current

output voltage is rising above the MosFet
Heated
desired level and signals Power Sink
to dissipate the excess energy in the Torque
form of heat.

Power Sink Motor Rotation

17
G+1.7kW PSINK Specifications
Specification 20-85 30-56 40-42 60-28 100-17
Sink Power Rating
Max. Peak Power (Electronically limited) (1) [W] 300W
Max. Continuous Power @ Tamb =25°C (2),(4) [W] 100W
Max. Peak Power Duration @ Tamb = 25°C [Sec] Max Ton = 60 Sec, Toff = 500 Sec (for cooling)
Max. Peak Power Duration @ Tamb = 50°C [Sec] Max Ton = 35 Sec, Toff = 900 Sec (for cooling)
Max. Sink Current (Vout >= 2V) (Electronically Limited) [A] 80 80 80 48 48
(1),(3)
Duty Cycle For Psink = 300W For more information see Figure 1.
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 30 Sec, Toff >= 105 Sec
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 20 Sec, Toff >= 55 Sec
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 10 Sec, Toff >= 45 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 30 Sec, Toff >= 170 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 20 Sec, Toff >= 150 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 10 Sec, Toff >= 90 Sec
Duty Cycle For Psink = 200W
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 30 Sec, Toff >= 55 Sec
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 20 Sec, Toff >= 20 Sec
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 10 Sec, Toff >= 20 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 30 Sec, Toff >= 145 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 20 Sec, Toff >= 110 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 10 Sec, Toff >= 80 Sec
- Electronic Power Limit
Protection - Over Current Protection
- Thermal Overload Protection (4)
Down Programming - output voltage 90% to 10% at
No Load [mSec] 14 17 21 25 51
Fall time with Power Sink [mSec] 700 1000 1200 1500 2600
Fall time without Power Sink
Recovery Time/Deviation
Vout = 6V, Iout: +100A -> -30A
Deviation [V] 0.6
Percentage [%] 10
Recovery to 0.5% or 100mV whichever is greater [mSec] 650
Vout = 12.5V, Iout: +100A -> -10A
Deviation [V] 0.5 0.17
Percentage [%] 4 1.4
Recovery to 0.5% or 100mV whichever is greater [mSec] 600 760
Vout = 20V, Iout: +100A -> -7.5A
Deviation [V] 0.5 0.18 0.25
Percentage [%] 1 0.9 1.25
Recovery to 0.5% or 100mV whichever is greater [mSec] 200 720 600
Vout = 30V, Iout: +70A -> -6A
Deviation [V] 0.18 0.25
Percentage [%] 0.6 0.9
Recovery to 0.5% or 100mV whichever is greater [mSec] 250 300
Vout = 40V, Iout: +50A -> -4.5A
Deviation [V] 0.25 0.4
Percentage [%] 0.7 1
Recovery to 0.5% or 100mV whichever is greater [mSec] 250 400
Vout = 50V, Iout: +50A -> -3.5A
Deviation [V] 0.4
Percentage [%] 0.8
Recovery to 0.5% or 100mV whichever is greater [mSec] 250
Vout = 60V, Iout: +34A -> -3A
Deviation [V] 0.4 0.6
Percentage [%] 0.6 1
Recovery to 0.5% or 100mV whichever is greater [mSec] 150 150
Vout = 80V, Iout: +30A -> -2A
Deviation [V] 0.6
Percentage [%] 0.75
Recovery to 0.5% or 100mV whichever is greater [mSec] 100
Vout = 100V, Iout: +24A -> -1.5A
Deviation [V] 0.6
Percentage [%] 0.6%
Recovery to 0.5% or 100mV whichever is greater [mSec] 50
Parallel Operation When using multiple units in parallel - all units CAN have Power Sink installed (5).
Series Operation Not Applicable.

18
 Sink [W] P_Sink/T_off
300
280
260
240
220
200
180
160
140 Ton = 30
120 Ton = 20
100 Ton = 10
80
60
40
20
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110
T_off [Sec]
Typical @ 25°C

Figure 1

(1) At Ambient Temperature, Tamb =25°C & 50°C.

(2) 100W is the max. continues power that Power Sink can handle without going into Thermal Overload Protection.
(1) - At Ambient Temperature, Tamb =25°C & 50°C.
(3) Higher Sink current will cause the power supply output voltage to rise.
(2) 100W is the max. continues power that Power Sink can handle without going into Thermal Overload Protection.
(4) Power
(3) - Higher Sink Supply
current shuts downthe
will cause in power
case ofsupply
Thermal Overload
output voltageProtection.
to rise.
(5) When
(4) - Power using
Supply multiple
shuts down in units
case inofparallel
Thermal Power Supplies
Overload with Psink installed MUST use the same software version.
Protection.
(6) Power
(5) - When usingSupplies with Psink
multiple units must- have
in parallel PowerMaster Control
Supplies sofware
with Psink version
installed updated
MUST to or
use the greater
same than 02.114.
software version.
(6) - Power Supplies with Psink must have Master Control sofware version updated to or greater than 02.15.

19
G+3.4kW PSINK Specifications
Specification 20-170 30-112 40-85 60-56 100-34
Sink Power Rating
Max. Peak Power (Electronically limited) (1) [W] 300W
Max. Continuous Power @ Tamb =25°C (2),(4) [W] 100W
Max. Peak Power Duration @ Tamb = 25°C [Sec] Max Ton = 60 Sec, Toff = 500 Sec (for cooling)
Max. Peak Power Duration @ Tamb = 50°C [Sec] Max Ton = 35 Sec, Toff = 900 Sec (for cooling)
Max. Sink Current (Vout >= 2V) (Electronically Limited) (1),(3) [A] 80 80 80 48 48
Duty Cycle For Psink = 300W For more information see Figure 1.
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 30 Sec, Toff >= 105 Sec
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 20 Sec, Toff >= 55 Sec
Power Sink = 300W @ Tamb = 25°C [Sec] Ton = 10 Sec, Toff >= 45 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 30 Sec, Toff >= 170 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 20 Sec, Toff >= 150 Sec
Power Sink = 300W @ Tamb = 50°C [Sec] Ton = 10 Sec, Toff >= 90 Sec
Duty Cycle For Psink = 200W
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 30 Sec, Toff >= 55 Sec
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 20 Sec, Toff >= 20 Sec
Power Sink = 200W @ Tamb = 25°C [Sec] Ton = 10 Sec, Toff >= 20 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 30 Sec, Toff >= 145 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 20 Sec, Toff >= 110 Sec
Power Sink = 200W @ Tamb = 50°C [Sec] Ton = 10 Sec, Toff >= 80 Sec
- Electronic Power Limit
Protection - Over Current Protection
- Thermal Overload Protection (4)
Down Programming - output voltage 90% to 10% at No Load
Fall time with Power Sink 20 25 30 38 75
[W] 600 800 900 1100 2100
Fall time without Power Sink
Recovery Time/Deviation [W]
Vout = 6V, Iout: +100A -> -30A [Sec]
Deviation 0.14
Percentage [Sec] 1.12
Recovery to 0.5% or 100mV whichever is greater 400
Vout = 12.5V, Iout: +100A -> -10A [A]
Deviation 0.47
Percentage 8
Recovery to 0.5% or 100mV whichever is greater 380
Vout = 20V, Iout: +100A -> -7.5A [Sec]
Deviation 0.14 0.17
Percentage [Sec] 0.7 0.9
Recovery to 0.5% or 100mV whichever is greater 140 450
Vout = 30V, Iout: +70A -> -6A [Sec]
Deviation 0.17 0.19
Percentage [Sec] 0.6 0.93
Recovery to 0.5% or 100mV whichever is greater 150 450
Vout = 40V, Iout: +50A -> -4.5A [Sec]
Deviation 0.23 0.4
Percentage [Sec] 1.15 1
Recovery to 0.5% or 100mV whichever is greater 350 450
Vout = 50V, Iout: +50A -> -3.5A
Deviation 0.4
Percentage [Sec] 0.8
Recovery to 0.5% or 100mV whichever is greater 250
Vout = 60V, Iout: +34A -> -3A [Sec]
Deviation 0.4 0.6
Percentage [Sec] 0.6 1
Recovery to 0.5% or 100mV whichever is greater 150 300
Vout = 80V, Iout: +30A -> -2A [Sec]
Deviation 0.6
Percentage [Sec] 0.75
Recovery to 0.5% or 100mV whichever is greater 130
Vout = 100V, Iout: +24A -> -1.5A [Sec]
Deviation [V] 0.6
Percentage [%] 0.6%
Recovery to 0.5% or 100mV whichever is greater [mSec] 70
Parallel Operation When using multiple units in parallel - all units CAN have Power Sink installed (4).
Series Operation Not Applicable

20
 Sink [W] P_Sink/T_off
300
280
260
240
220
200
180
160
140 Ton = 30
120 Ton = 20
100 Ton = 10
80
60
40
20
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110
T_off [Sec]
Typical @ 25°C

Figure 2

(1)
(1)At- Ambient
At Ambient Temperature,
Temperature, TambTamb =25°C
=25°C & 50°C.
& 50°C.
(2)100W
(2) - 100Wis the max.
is the continues
max. continues power
powerthat
thatPower
PowerSink
Sinkcan handle
can handlewithout
without going intoThermal
going into ThermalOverload
OverloadProtection.
Protection.
(3) - Higher Sink current will cause the power supply output voltage to rise.
(3) Higher Sink current will cause the power supply output voltage to rise.
(4) - Power Supply shuts down in case of Thermal Overload Protection.
(4)
(5)Power
- When Supply
using shuts down
multiple unitsinincase of Thermal
parallel - PowerOverload Protection.
Supplies with Psink installed MUST use the same software version.
(6)When
(5) using
- Power multiple
Supplies withunits
Psink inmust
parallel
have Power Supplies
Master Controlwith Psinkversion
sofware installed MUSTtouse
updated or the same
greater software
than 02.15. version.
(6) Power Supplies with Psink must have Master Control sofware version updated to or greater than 02.114.

21
How to order G1.7kW PSINK - Power Supply Identification / Accessories
G 20 - 85 - - PSINK -
Series Name Output Output Interface Options Accessories Options
Front Panel Type Voltage Current M - Printed *User Manual
Empty: standard (0~20V) (0~85A) * User Manual & GUI are
available on the website
B: Blank Front Panel (ATE version) P - Bus Parralleling Cable

AC Inputs (All Models)

1Ø, 85 ~ 265Vac
Interface Options (Factory installed) P/N
LAN ( 1.5 compliant with Multi-Drop capability)- built-in -
USB 2.0 compliant with Multi-Drop capability - built-in -
RS-232/RS-485 - built-in -
Isolated Analog Program/Monitor Inter face
-
(5V/10V Pgm/Mon with 600V isolation) - built-in
IEEE (488.2 & SCPI compliant with Multi-Drop capability installed) IEEE
Modbus-TCP MDBS
EtherCAT ECAT

Models 1.7kW
Model Voltage (V) Current (A) Power (W)
G20-85-PSINK 0~20V 0~85 1700
G30-56-PSINK 0~30V 0~56 1680
G40-42-PSINK 0~40V 0~42 1680
G60-28-PSINK 0~60V 0~28 1680
G100-17-PSINK 0~100V 0~17 1700

Accessories
Accessories will be sent separately from the Power Supply packing, according to order.
1. Serial Communication cable. RS-232/RS-485 cable is used to connect the power supply to the Host PC.
Mode RS-485 RS-232
PC Connector, Communication Cable, Power Supply Connector DB-9F. Shielded L=2m. RJ-45 DB-9F. Shielded L=2m, RJ-45
P/N GEN/485-9 GEN/232-9
2. Serial link cable (Included with the power supply)
Daisy-chain up to 31 ™ power supplies.
Mode Power Supply Connector Communication Cable P/N
RS-485 RJ-45 Shielded L=50cm GEN/RJ45

3. Bus Paralleling cable

Connectors Cables P/N
2013595-1 (TYCO) Shielded L=11cm G/P
4. User Manual
Printed User Manual G/M

22
How to order G3.4kW PSINK - Power Supply Identification / Accessories
G 20 - 170 - - PSINK - -
Series Name Output Output Interface Options AC Input Options Accessories Options
Front Panel Type Voltage Current 1P208 (1Ø 170~265VAC) M - Printed *User Manual
Empty: standard (0~20V) (0~170A) 3P208 (3Ø 170~265VAC) * User Manual & GUI are
available on the website
B: Blank Front Panel (ATE version) 3P400 (3Ø 342~460VAC)
3P480 (3Ø 342~528VAC) P - Bus Parralleling Cable

Interface Options (Factory installed) P/N

LAN ( 1.5 compliant with Multi-Drop capability)- -
built-in
USB 2.0 compliant with Multi-Drop capability - built-in -
RS-232/RS-485 - built-in -
Isolated Analog Program/Monitor Interface -
(5V/10V Pgm/Mon with 600V isolation) - built-in
IEEE (488.2 & SCPI compliant with Multi-Drop capability IEEE
installed)
Modbus-TCP MDBS
EtherCAT ECAT

Models G3.4kW
Model Output Voltage VDC Output Current (A) Output Power (W)
G20-170-PSINK 0~20V 0~170 3400
G30-112-PSINK 0~30V 0~112 3360
G40-85-PSINK 0~40V 0~85 3400
G60-56-PSINK 0~60V 0~56 3360
G100-34-PSINK 0~100V 0~34 3400

Accessories
Accessories will be sent separately from the Power Supply packing, according to order.
1. Serial Communication cable. RS-232/RS-485 cable is used to connect the power supply to the Host PC.
Mode RS-485 RS-232
PC Connector, Communication Cable, Power Supply Connector DB-9F. Shielded L=2m. RJ-45 DB-9F. Shielded L=2m, RJ-45
P/N GEN/485-9 GEN/232-9
2. Serial link cable (Included with the power supply)
Daisy-chain up to 31 ™ power supplies.
Mode Power Supply Connector Communication Cable P/N
RS-485 RJ-45 Shielded L=50cm GEN/RJ45
3. Bus Paralleling cable
Connectors Cables P/N
2013595-1 (TYCO) Shielded L=11cm G/P
4. User Manual
Printed User Manual G/M

23
 NORTH AMERICA Denmark
TDK-Lambda Americas Inc TDK-Lambda Nordic
405 Essex Rd. Neptune, NJ 07753 Haderslevvej 36B, DK-6000 Kolding, Denmark
Tel: +1-732-922-9300 Fax: +1-732-922-1441 TEL: +45-8853-8086
E-mail: [email protected] E-mail: [email protected]
www.us.lambda.tdk.com www.emea.lambda.tdk.com/dk
UK JAPAN
TDK-Lambda UK Ltd. TDK-Lambda Corporation
Kingsley Avenue Ilfracombe, Devon Nihonbashi Takashimaya Mitsui Bldg. 2-5-1 Nihonbashi,
EX 34 8ES, United Kingdom Chuo-ku, Tokyo 103-6128, JAPAN
Tel: +44-1271-856666 Fax: +44-1271-864894 TEL: +81-3-6778-1113 FAX: +81-3-6778-1160
E-mail: [email protected] www.jp.lambda.tdk.com
www.emea.lambda.tdk.com/uk
CHINA
FRANCE
TDK-Lambda (China) Electronics Co. Ltd,
TDK-Lambda France SAS Shanghai Office 5th Floor Kehui Tower, 1188 Qinzhou Road (North),
3 Avenue du Canada, Xuhui District Shanghai 200233, China
Parc Technopolis - Bâtiment Sigma, Tel: +86-21-6485-0777 Fax: +86-21-6485-0666
91940 Les Ulis – France CS 41077 www.lambda.tdk.com.cn
Tel: +33 1 60 12 71 65 Fax: +33 1 60 12 71 66
E-mail: [email protected] Beijing Branch of TDK-Lambda (China) Electronic Co. Ltd.
www.emea.lambda.tdk.com/fr Room 12B11-12B12, Unit 7 Dacheng square, No.28
Xuanwumenxi Street, Xuanwu District Beijing, 100053, CHINA
GERMANY Tel: +86-10-6310-4872 Fax: +86-10-6310-4874
TDK-Lambda Germany GmbH www.lambda.tdk.com.cn
Karl-Bold-Str.40, Shenzhen Branch of TDK-Lambda (China) Electronics Co.Ltd.
D-77855 Achern, Germany 69/F, Ping An Finance Centre, 5033 Yitian Road,
Tel: +49-7841-666-0 Fax: +49-7841-500-0 Futian District, Shenzhen,China
E-mail: [email protected] Tel: +86-755-83588261 Fax: +86-755-83588260
www.emea.lambda.tdk.com/de www.lambda.tdk.com.cn
AUSTRIA KOREA
TDK-Lambda Germany GmbH Austria Sales Office TDK-Lambda Corporation Korea Branch
Aredstrasse 22, 2544 Leobersdorf, Austria Seocho-Dong,12F. Songnam Bldg. 273, Gangnam Daero,
Tel: +43-2256-65584 Fax: +43-2256-64512 Seocho-Gu, Seoul 06730, Republic of Korea
E-mail: [email protected] Tel: +82-2-3473-7051 Fax: +82-2-3472-9137
www.emea.lambda.tdk.com/at www.lambda.tdk.co.kr
ITALY SINGAPORE
TDK-Lambda France Sas Succursale Italiana TDK-Lambda Singapore Pte.Ltd.
Via Giacomo Matteotti 62, Blk 1008 Toa Payoh North # 07-01/03
20092 Cinisello Balsamo (MI), Italia Singapore 318996
Tel: +39-02-6129-3863 Fax: +39-02-6129-0900 Tel: +65-6251-7211 Fax: +65-6250-9171
E-mail: [email protected] www.sg.lambda.tdk.com
www.emea.lambda.tdk.com/it
INDIA
ISRAEL
TDK India Private Limited. Power Supply Division
TDK-Lambda Ltd. #87, The Centrum, 4th Floor, Infantry Road, Bengaluru,
Sales Office: Alexander Yanai 1, Petah Tikva, 4927701, ISRAEL Karnataka, -560 001, INDIA
Tel: +972-3-9024-333 Fax: +972-3-9024-777 Tel: +91-80-40390660 Fax: +91-80-40390603
Plant: 56 Haharoshet St., MALAYSIA
Karmiel Industrial Zone 2165158, Israel
Tel: +972-4-9887-491 Fax: +972- 4-9583-071 TDK-Lambda Malaysia Sdn. Bhd. (Nilai Office)
www.emea.lambda.tdk.com/il E-mail: [email protected] c/o TDK (Malaysia) Sdn. Bhd., Lot 709, Nilai Industrial Estate
71800 Nilai, Negeri Sembilan, MALAYSIA
Switzerland TEL: +60-6-797-8800 Fax: +60-6-797-8966
TDK-Lambda Germany GmbH
™

Switzerland Sales Office, Eichtalstr. 55

8634 Hombrechtikon - Switzerland
Tel: +41 44 850 53 53
E-mail: [email protected]
www.emea.lambda.tdk.com/ch

https://product.tdk.com/en/power
www.emea.lambda.tdk.com