Scribd
Upload
187 views2 pages

Data Sheet OPT104

This document summarizes an optical reflex sensor designed for roller conveyor systems. The sensor has a range of 550mm, operates using infrared light, and has a service life of 100,000 hours. It has compact dimensions allowing installation between rollers, and is protected against mechanical damage. Key features include electronic background suppression, integrated logic functions, and IP65 enclosure rating.

Uploaded by

vitezix
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
187 views2 pages

Data Sheet OPT104

This document summarizes an optical reflex sensor designed for roller conveyor systems. The sensor has a range of 550mm, operates using infrared light, and has a service life of 100,000 hours. It has compact dimensions allowing installation between rollers, and is protected against mechanical damage. Key features include electronic background suppression, integrated logic functions, and IP65 enclosure rating.

Uploaded by

vitezix
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Reflex Sensor

for Roller Conveyor Systems

OPT104
Part Number

Technical Data
Optical Data

Range Potentiometer min Potentiometer center Potentiometer max Switching Hysteresis Light Source Wave Length Service Life (T = +25 C) Risk Group (EN 62471) max. Ambient Light Opening Angle
Electrical Data

550 mm 220...270 mm 320...400 mm 550...630 mm < 15 % Infrared Light 880 nm 100000 h 1 10000 Lux 5 18...30 V DC < 30 mA 100 Hz 5 ms < 10 % -15...50 C 1 < 0,8 V 200 mA yes yes yes yes yes yes yes III Plastic yes IP65 M12 1 88 cm K04 19,2...28,8 V 86 mA 4...7 bar 0,8 mm 20 NL/min 100 NL/min 2 81 41 3/2-Way NC

Supply Voltage Current Consumption Sensor (Ub = 24 V) Switching Frequency Response Time Temperature Drift Temperature Range Switching Outputs Switching Output Voltage Drop PNP Switching Output/Switching Current

Electronic Background Suppression Fully Encapsulated Integrated Logic Scaled switching Distance Adjuster

Short Circuit Protection Reverse Polarity Protection Overload Protection Logic Single Block Discharge Block Discharge Pneumatic Solenoid Valve Unit Protection Class
Mechanical Data

Housing Full Encapsulation Degree of Protection Connection Cable Length


Pneumatic Solenoid Valve Unit

Valve no. Supply Voltage Valve

These sensors have been specially designed for use in accumulation roller conveyors. Their compact design allows for installation between rollers below the transport level. They are thus protected against mechanical damage.

Current Consumption Valve Operating Pressure Nominal Width Nominal flow rate 1 -> 2 Nominal flow rate 2 -> 3 Supply line connector pipe Working line connector pipe Valve function Switching function PNP NC Connection Diagram No. Control Panel No. Suiting Connection Technology No. Suiting Mounting Technology No.

714 OP1

420

1 = Transmitter Diode 2 = Receiver Diode

All dimensions in mm (1 mm = 0.03937 Inch)

714

Legend
Supply Voltage + Supply Voltage 0 V Supply Voltage (AC Voltage) Switching Output Switching Output Contamination/Error Output Contamination/Error Output Input (analog or digital) Teach Input Time Delay (activation) Shielding Interface Receive P ath Interface Send Path Ready Ground Clock Output/Input programmable Test Input Test Input inverted Trigger Input Analog Output Ground for the Analog Output Block Discharge Valve Output Valve Control Output + Valve Control Output 0 V Synchronization Receiver-Line Emitter-Line Grounding Switching Distance Reduction Ethernet Receive P ath Ethernet Send Path Interfaces-Bus A(+)/B() Emitted Light disengageable Power over Ethernet

(NO) (NC) (NO) (NC)

Wire Colors according to DIN IEC 757


Black Brown Red Orange Yellow Green Blue Violet Grey White Pink Green Yellow

Complimentary Products
Adapter OPT70N, 70S, 70S+

Switching Distance Deviation


Typical characteristic curve based on Kodak white, 90 %

Ctrl.Panel
dSr/mm
OP1

OPT
10
Specifications are subject to change without notice

0 -10 -20 -30 -40 -50 -60

30 05

-70 200 250 300 350 400 450 500

Sr/mm

550

600

05 = Switching Distance Adjuster 30 = Switching Status/Contamination Warning

Pot. = Potentiometer Setting dSr = Switching Distance Change

black 6 % grey 18 %

Sensors for your success www.wenglor.com Sensors for your success www.wenglor.com

You might also like