Engineering

Sprocket Engineering Data

Roller Chain Dimensions
Sprocket Tooth Dimensions
Maximum Hub Recommendations
Application And Selection
Hardening
Chain Length Calculation
Speed Ratios
Sprocket Diameters
Horsepower Ratings

Sprockets
American sprocket manufacturers have adopted 4 specific types of sprocket construction styles as American Standards. In
addition to the standard sprockets, special sprockets may be available in the same styles.

Style A - Flat sprocket with no hub extension either side.

Style B - Sprocket with hub extension one side.
Style C - Sprocket with hub extension both sides.
Style D - Sprocket with a detachable bolt on hub attached to a plate.
LTB

Hub Pitch
OD Dia. Hub
Pitch Dia. Dia.
Dia. Hub
Dia.

LTB
Length Thru Bore

Single Single Single Single

Type A Hub Type B Hub Type C Hub Type D Hub

E-152
 Sprocket
Nomenclature

Multiple Strand Sprockets

Listed using a letter prefix starting with the letter
D for Double Strand, E for Triple Strand, and F
for Quadruple, etc. They also have the same hub
configuration letter designation listed on previous
page. In addition to the four specific types,
sprockets may also be made in various other styles.
Double Triple

Five common styles are:

QD MST®
The QD (quick detachable) sprocket; here a tapered bushing The MST® (Martin Split Taper®) is another style of bushed
is bolted into the bore machined in the sprocket. This sprocket. The bushing is similar to the QD style except it
bushing, when inserted into the sprocket, compresses onto has an external key that fits into the driven product.
the shaft providing a tight grip.
.168

OD C HOD
Bore

L LTB

TB Split
The TB (taper bushed) sprocket is another style of an A Split type sprocket is used in place of solid type to allow
interchangeable bushed sprocket, which provides a positive quick installation without disruption of shaft and alignment.
grip on a driven shaft.

Shear Pin Sprocket

E-153
 Sprocket
Nomenclature

Sprocket nomenclatures provide the chain pitch written to the left of the hub style code letter followed by the number of
teeth in the sprocket. If the sprocket is to be multiple strand, the prefix code letter is added to the beginning of the part
number.

A suffix of H is added if the teeth are to be heat treated. If the sprocket is to be bored for QD, Taper Bushed or MST, the
center hub letter is changed. For QD and MST styles the letter designation of the bushing is used in lieu of the hub style
code. If a taper bushing is to be used, the two letters TB are added behind the hub code letter.

In some instances, the material a sprocket is to be manufactured from will be added into the part number as a suffix.

For example:

SS Stainless Steel Material

NM Non-Metallic
BR Brass or Bronze Material
CD Cadmium Plated
Zi Zinc Plated
Ni Nickel Plated
CH Chrome Plated

If the part is to be used with a shear pin device, the center hub style letter is substituted with an SP.

Most manufacturers of sprockets conform to the ANSI (American Standards Institute) and Martin conforms to the Type
II tooth form as given in the standard B29.1 - 1975. It is not necessary to show detailed tooth information on sprocket
drawings, just specify ANSI standard tooth form.

Face Width

Caliper Bottom
Diameter Dia.
Pitch
Bore Dia.
Maximum
Hub and
Outside Groove
Dia. Dia.

LTB

E-154
 Sprocket
Nomenclature

Sprocket Dimensional Specifications

Bottom Diameter The diameter of a circle tangent to the bottoms of the tooth spaces.
(BD)

Caliper Diameter Since the bottom diameter of a sprocket with odd number of
teeth cannot be measured directly, caliper diameters are the
measurement across the tooth spaces nearly opposite.

Pitch Diameter The diameter across to the pitch circle which is the circle followed by the
centers of the chain pins as the sprocket revolves in mesh with the chain.
(PD)
Pitch
PD =
SIN (180/Nt)

Outside Diameter The measurement from the tip of the sprocket tooth across to the
corresponding point directly across the sprocket. It is comparatively
(OD)
unimportant as the tooth length is not vital to proper meshing with the
chain. The outside diameter may vary depending on type of cutter used.

OD = (Pitch) (.6 + COT [180 / Nt])

Hub Diameter That distance across the hub from one side to another. That
distance across the hub from one side to another.
(HOD)

Maximum Sprocket Maximum Sprocket Bore is determined by the required hub wall thickness
for proper strength. Allowance must be made for keyway and setscrews.
Bore

Face Width Face width is limited in its maximum dimension to allow proper
clearance to provide for chain engagement and disengagement.
The minimum width is limited to provide the proper
strength to carry the imposed loads.

Length Thru Bore Length Thru Bore (or LTB) must be sufficient to allow a long
enough key to withstand the torque transmitted by the shaft.
(LTB)
This also assures stability of the sprocket on the shaft.

E-155
 Roller Chain
Dimensions

Inside Inside
Cottered Riveted Average Cottered Riveted Average
ANSI Roller Roller Link ANSI Roller Roller Link
Chain Chain Tensile Chain Chain Tensile
Number Width Dia. Plate Number Width Dia. Plate
Width* Width* Strength Width* Width* Strength
Height Height
Standard Series Chain Standard Series Chain
25 1/8 .130 .237 .37 .34 875 100 3/4 .750 1.187 1.73 1.61 24000
25-2 1/8 .130 .237 .63 .59 1750 100-2 3/4 .750 1.187 3.14 3.02 48000
25-3 1/8 .130 .237 .88 .84 2626 100-3 3/4 .750 1.187 4.56 4.43 72000
35 3/16 .200 .356 .56 .50 2100 100-4 3/4 .750 1.187 5.97 5.84 96000
35-2 3/16 .200 .356 .96 .90 4200 100-5 3/4 .750 1.187 7.38 7.25 120000
35-3 3/16 .200 .356 1.36 1.31 6300 100-6 3/4 .750 1.187 8.78 8.66 144000
35-4 3/16 .200 .356 1.76 1.70 8400 120 1 .875 1.425 2.14 2.00 34000
35-5 3/16 .200 .356 2.16 2.11 10500 120-2 1 .875 1.425 3.93 3.79 68000
35-6 3/16 .200 .356 2.57 2.51 12600 120-3 1 .875 1.425 5.72 5.58 102000
40 5/16 .312 .475 .72 .67 3700 120-4 1 .875 1.425 7.52 7.38 136000
40-2 5/16 .312 .475 1.29 1.24 7400 120-5 1 .875 1.425 9.31 9.17 170000
40-3 5/16 .312 .475 1.85 1.80 11100 120-6 1 .875 1.425 11.10 10.96 204000
40-4 5/16 .312 .475 2.42 2.37 14800 140 1 1.000 1.662 2.31 2.14 46000
40-6 5/16 .312 .475 3.56 3.51 22200 140-2 1 1.000 1.662 4.24 4.07 92000
41 1/4 .306 .383 .65 .57 2000 140-3 1 1.000 1.662 6.16 6.00 138000
50 3/8 .400 .594 .89 .83 6600 140-4 1 1.000 1.662 8.09 7.93 184000
50-2 3/8 .400 .594 1.60 1.55 13200 140-6 1 1.000 1.662 11.94 11.78 276000
50-3 3/8 .400 .594 2.31 2.26 19800 160 1 1/4 1.125 1.900 2.73 2.54 58000
50-4 3/8 .400 .594 3.03 2.97 26400 160-2 1 1/4 1.125 1.900 5.04 4.85 116000
50-5 3/8 .400 .594 3.75 3.69 33000 160-3 1 1/4 1.125 1.900 7.35 7.16 174000
50-6 3/8 .400 .594 4.46 4.40 39600 160-4 1 1/4 1.125 1.900 9.66 9.47 232000
60 1/2 .469 .712 1.11 1.04 8500 160-6 1 1/4 1.125 1.900 14.27 14.09 348000
60-2 1/2 .469 .712 2.01 1.94 17000 180 1 13/32 1.406 2.137 3.15 2.88 76000
60-3 1/2 .469 .712 2.91 2.84 25500 180-2 1 13/32 1.406 2.137 5.75 5.48 152000
60-4 1/2 .469 .712 3.81 3.74 34000 180-3 1 13/32 1.406 2.137 8.34 8.07 228000
60-5 1/2 .469 .712 4.71 4.64 42500 200 1 1/2 1.562 2.375 3.44 3.12 95000
60-6 1/2 .469 .712 5.60 5.53 51000 200-2 1 1/2 1.562 2.375 6.26 5.94 190000
80 5/8 .625 .950 1.44 1.32 14500 200-3 1 1/2 1.562 2.375 9.08 8.76 285000
80-2 5/8 .625 .950 2.59 2.47 29000 200-4 1 1/2 1.562 2.375 11.90 11.58 380000
80-3 5/8 .625 .950 3.74 3.62 43500 200-6 1 1/2 1.562 2.375 17.52 17.21 570000
80-4 5/8 .625 .950 4.90 4.79 58000 240 1 7/8 1.875 2.812 4.06 3.72 130000
80-5 5/8 .625 .950 6.06 5.94 72500 240-2 1 7/8 1.875 2.812 7.52 7.18 260000
80-6 5/8 .625 .950 7.22 7.10 87000 *Dimensions are across pins.
*Dimensions are across pins.

Standard Keyways and Setscrews Standard Bore Tolerances

Diameter of Keyway Diameter of Keyway 1" and Less + .001 -.000
Setscrew Setscrew
Shaft Width × Depth Shaft Width × Depth 1 1/16" to 2" + .002 -.000
1/2 - 9/16 1/8 × 1/16 10-24 2 5/16 - 2 3/4 5/8 × 5/16 5/8 * 2 1/16" to 3" + .003 -.000
5/8 - 7/8 3/16 × 3/32 1/4 2 13/16 - 3 1/4 3/4 × 3/8 5/8 * 3 1/16" & up + .004 -.000
15/16 - 1 1/4 1/4 × 1/8 5/16 3 5/16 - 3 3/4 7/8 × 7/16 3/4 Bores with closer tolerances will be supplied at a
1 5/16 - 1 3/8 5/16 × 5/32 5/16 3 13/16 - 4 1/2 1 × 1/2 3/4 slight increase in price.
1 7/16 - 1 3/4 3/8 × 3/16 3/8 4 9/16 - 5 1/2 1 1/4 × 5/8 3/4
1 13/16 - 2 1/4 1/2 × 1/4 1/2 * 5 9/16 - 6 1/2 1 1/2 × 3/4 3/4
*Hub size may require smaller setscrews in some instances.

E-156
 Sprocket Tooth Dimensions

THR

M7
M6
M5
M4
Single Hot M3 M3
Rolled Steel Plate M2 M2
t1 K K K K K K K
t2 t4
Pitch
Line

Single Double and Triple Quadruple and Other Multiples

Dimensions in Inches
Chain Data For All Sprockets For 4 or more Strands
Single Double and Triple Tolerance Minus Tol-
Roller Strand Strand on t & M erance
ASA Pitch Roller
Width t1 & THR t4 M2 M3 M4 M5 M6 M8 M10 M12 M16 K Machined on THR
Chain No. P Dia.
W t2 M2 M3
Standard Series Roller Chain Sprockets
25 .25 .125 .130 .110 .107 .359 .611 .096 .348 .600 .852 1.104 1.356 1.860 2.364 2.868 3.876 .252 .007 .021
35 .375 .188 .200 .168 .162 .561 .960 .149 .548 .947 1.346 1.745 2.144 2.942 3.740 4.538 6.134 .399 .008 .027
41 .5 .25 .306 .227 † † † † † † † † † † † † † † .009 .032
40 .5 .313 .312 .284 .275 .841 1.407 .256 .822 1.388 1.954 2.520 3.086 4.218 5.250 6.482 8.746 .566 .009 .035
50 .625 .375 .400 .343 .332 1.045 1.758 .311 1.024 1.737 2.450 3.163 3.876 5.302 6.728 8.154 11.006 .713 .010 .036
60 .75 .5 .469 .459 .444 1.341 2.238 .418 1.315 2.212 3.108 4.006 4.903 6.697 8.491 10.258 13.873 .897 .011 .036
80 1 .625 .625 .575 .557 1.700 2.863 .526 1.679 2.832 3.985 5.138 6.291 8.597 10.903 13.209 17.821 1.153 .012 .040
100 1.25 .75 .750 .692 .669 2.077 3.484 .633 2.041 3.449 4.857 6.265 7.673 10.489 13.305 16.121 21.753 1.408 .014 .046
120 1.5 1 .875 .924 .894 2.683 4.472 .848 2.637 4.426 6.215 8.004 9.793 13.371 16.949 20.527 1.789 .016 .057

Sprocket Tooth
140 1.75 1 1.000 .924 .894 2.818 4.742 .848 2.772 4.696 6.620 8.544 10.468 14.316 18.164 22.012 1.924 .016 .057
160 2 1.25 1.125 1.156 1.119 3.424 5.729 1.063 3.368 5.673 7.978 10.283 12.588 17.198 21.808 2.305 .019 .062
180 2.25 1.406 1.406 1.301 1.259 3.851 6.443 1.197 3.789 6.381 8.973 11.565 14.157 19.341 2.592 -.020 -.068

Dimensions
200 2.5 1.5 1.562 1.389 1.344 4.161 6.978 1.278 4.095 6.912 9.729 12.546 15.363 20.997 2.817 .021 .072
240 3 1.875 1.875 1.738 1.682 5.140 8.598 1.601 5.059 8.517 11.975 15.433 18.891 3.458 -.025 -.087
Heavy Series Chain Sprockets
60H .750 .500 .469 .459 .444 1.472 2.500 .418 1.446 2.474 3.502 4.530 5.558 7.614 1.028 -.011 -.036
80H 1.000 .625 .625 .575 .557 1.840 3.123 .526 1.809 3.092 4.375 5.568 6.941 9.507 1.283 -.012 -.040
100H 1.250 .750 .750 .692 .669 2.208 3.747 .633 2.172 3.711 5.250 6.789 8.328 11.406 1.539 -.014 -.046
120H 1.500 1.000 .875 .924 .894 2.818 4.742 .848 2.772 4.696 6.620 8.544 10.468 14.316 1.924 -.016 -.057
140H 1.750 1.000 1.000 .924 .894 2.949 5.004 .848 2.903 4.958 7.013 9.068 11.123 15.233 2.055 -.016 -.057
160H 2.000 1.250 1.125 1.156 1.119 3.555 5.991 1.063 3.499 5.935 8.371 10.807 13.243 18.115 2.436 -.019 -.062
180H 2.250 1.406 1.406 1.301 1.259 3.982 6.705 1.197 3.920 6.643 9.366 12.089 14.812 20.258 2.723 -.020 -.068
E-157

200H 2.500 1.500 1.562 1.389 1.344 4.427 7.510 1.278 4.361 7.444 10.527 13.610 16.693 22.859 3.083 -.021 -.072
† = Not made in multiple strands.
 Maximum Hub
Dimensions
Recommended Max. Hub and Bore Sizes
American Standard No. 25 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 555 9/64 .... 16 6940 31/32 9/16 26 8645 1 49/64 1 1/4 Shaft Width x Depth Set- Setscrew Setscrew not
7 1300 15/64 .... 17 7290 1 3/64 5/8 27 8655 1 55/64 1 1/4 Screw Over Key over key
8 2080 5/16 .... 18 7590 1 1/8 3/4 28 8650 1 15/16 1 1/4
9 2860 7/16 1/4 19 7840 1 7/32 13/16 29 8625 2 1/64 1 1/4 3/8 3/32 × 3/64 3/16 7/16 3/8
10 3610 1/2 1/4 20 8050 1 19/64 7/8 30 8580 2 3/32 1 5/16 7/16 3/32 × 3/64 3/16 15/32 3/8
11 4310 9/16 5/16 21 8230 1 3/8 7/8 31 8540 2 11/64 1 3/8 1/2 - 9/16 1/8 × 1/16 3/16 1/2 3/8
12 4960 41/64 3/8 22 8370 1 29/64 15/16 32 8465 2 1/4 1 1/2 5/8 - 7/8 3/16 × 3/32 1/4 11/16 1/2
13 5540 47/64 7/16 23 8480 1 17/32 1 35 8200 2 31/64 1 11/16 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
14 6070 13/16 9/16 24 8560 1 39/64 1 1/16 40 7580 2 57/64 1 7/8 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
15 6530 57/64 9/16 25 8610 1 11/16 1 3/16 45 6820 3 9/32 2 1/4 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4

American Standard No. 35 Std. Keyway (Am. Std.) and Setscrew

No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 290 15/64 .... 16 3630 1 15/32 15/16 26 4525 2 43/64 1 3/4 Shaft Width x Depth Set- Setscrew Setscrew not
7 680 3/8 .... 17 3810 1 19/32 1 1/16 27 4530 2 51/64 1 3/4 Screw Over Key over key
8 1090 1/2 1/4 18 3970 1 23/32 1 3/16 28 4525 2 59/64 1 7/8
9 1495 5/8 3/8 19 4100 1 27/32 1 1/4 29 4510 3 1/32 2 7/16 3/32 × 3/64 3/16 15/32 3/8
10 1885 3/4 1/2 20 4210 1 61/64 1 1/4 30 4490 3 5/32 2 1/8 1/2 - 9/16 1/8 × 1/16 3/16 1/2 3/8
11 2260 55/64 9/16 21 4300 2 5/64 1 5/16 31 4470 3 9/32 2 1/4 5/8 - 7/8 3/16 × 3/32 1/4 11/16 1/2
12 2590 63/64 9/16 22 4380 2 13/64 1 7/16 32 4430 3 25/64 2 1/4 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
13 2900 1 7/64 11/16 23 4430 2 5/16 1 9/16 35 4290 3 3/4 2 1/2 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
14 3170 1 15/64 13/16 24 4480 2 7/16 1 11/16 40 3970 4 23/64 2 13/16 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
15 3420 1 23/64 7/8 25 4510 2 9/16 1 3/4 45 3570 4 61/64 3 1/4 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1

American Standard No. 41 Std. Keyway (Am. Std.) and Setscrew

No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 130 27/64 1/8 16 1630 2 1/16 1 5/16 26 2040 3 43/64 2 3/8 Shaft Width x Depth Set- Setscrew Setscrew not
7 305 19/32 5/16 17 1720 2 15/64 1 7/16 27 2040 3 53/64 2 9/16 Screw Over Key over key
8 495 49/64 1/2 18 1790 2 25/64 1 5/8 28 2040 4 2 3/4
9 675 15/16 9/16 19 1850 2 35/64 1 3/4 29 2040 4 5/32 2 3/4 5/8 - 7/8 3/16 × 3/32 1/4 11/16 1/2
10 850 1 3/32 11/16 20 1890 2 23/32 1 3/4 30 2020 4 5/16 2 13/16 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
11 1020 1 17/64 7/8 21 1940 2 7/8 1 7/8 31 2020 4 15/32 2 15/16 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
12 1170 1 27/64 7/8 22 1970 3 1/32 2 32 2000 4 41/64 3 1/8 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
13 1310 1 37/64 1 1/16 23 2000 3 3/16 2 3/16 35 1930 5 7/64 3 5/16 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
14 1430 1 3/4 1 1/4 24 2020 3 23/64 2 1/4 40 1780 5 29/32 3 7/8 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
15 1540 1 29/32 1 1/4 25 2030 3 33/64 2 1/4 45 1600 6 45/64 4 15/16 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2

American Standard No. 40 Std. Keyway (Am. Std.) and Setscrew

No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 220 21/64 .... 16 2720 1 63/64 1 1/4 26 3400 3 37/64 2 5/16 Shaft Width x Depth Set- Setscrew Setscrew not
7 510 1/2 1/4 17 2860 2 9/64 1 5/16 27 3405 3 47/64 2 7/16 Screw Over Key over key
8 820 43/64 3/8 18 2980 2 19/64 1 1/2 28 3405 3 29/32 2 5/8
9 1125 27/32 9/16 19 3080 2 29/64 1 11/16 29 3395 4 1/16 2 3/4 5/8 - 7/8 3/16 × 3/32 1/4 11/16 1/2
10 1420 1 5/8 20 3160 2 5/8 1 3/4 30 3370 4 7/32 2 3/4 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
11 1690 1 11/64 3/4 21 3230 2 25/32 1 3/4 31 3360 4 3/8 2 7/8 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
12 1940 1 21/64 7/8 22 3290 2 15/16 1 15/16 32 3330 4 35/64 3 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
13 2180 1 1/2 1 23 3330 3 3/32 2 1/16 35 3220 5 1/64 3 1/4 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
14 2380 1 21/32 1 1/8 24 3360 3 17/64 2 1/4 40 2970 5 13/16 3 13/16 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
15 2560 1 13/16 1 1/4 25 3380 3 27/64 2 1/4 45 2670 6 39/64 4 13/16 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2

American Standard No. 50 Std. Keyway (Am. Std.) and Setscrew

No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 155 27/64 1/8 16 1960 2 31/64 1 11/16 26 2445 4 31/64 2 15/16 Shaft Width x Depth Set- Setscrew Setscrew not
7 370 41/64 3/8 17 2060 2 11/16 1 3/4 27 2450 4 11/16 3 3/16 Screw Over Key over key
8 590 27/32 9/16 18 2150 2 57/64 1 7/8 28 2445 4 57/64 3 1/4
9 810 1 1/16 11/16 19 2220 3 5/64 2 1/16 29 2440 5 5/64 3 5/16 5/8 - 7/8 3/16 × 3/32 1/4 11/16 1/2
10 1020 1 17/64 7/8 20 2280 3 9/32 2 1/4 30 2430 5 9/32 3 1/2 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
11 1220 1 15/32 15/16 21 2330 3 31/64 2 1/4 31 2415 5 31/64 3 11/16 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
12 1400 1 43/64 1 1/8 22 2370 3 11/16 2 7/16 32 2395 5 11/16 3 3/4 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
13 1570 1 7/8 1 1/4 23 2400 3 57/64 2 5/8 35 2320 6 9/32 4 9/32 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
14 1720 2 5/64 1 5/16 24 2420 4 5/64 2 3/4 40 2140 7 9/32 5 1/2 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
15 1850 2 9/32 1 1/2 25 2440 4 9/32 2 3/4 45 1930 8 9/32 6 1/4 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2

American Standard No. 60 Std. Keyway (Am. Std.) and Setscrew

No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 120 33/64 1/4 16 1480 2 63/64 1 15/16 26 1840 5 25/64 3 5/8 Shaft Width x Depth Set- Setscrew Setscrew not
7 275 49/64 1/2 17 1550 3 7/32 2 3/16 27 1845 5 5/8 3 3/4 Screw Over Key over key
8 445 1 1/32 5/8 18 1610 3 15/32 2 1/4 28 1840 5 7/8 3 7/8
9 610 1 9/32 7/8 19 1670 3 45/64 2 7/16 29 1835 6 7/64 4 1/16 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
10 770 1 33/64 1 20 1720 3 61/64 2 11/16 30 1830 6 11/32 4 9/16 1 5/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
11 920 1 49/64 1 1/4 21 1750 4 3/16 2 3/4 31 1815 6 19/32 4 13/16 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
12 1050 2 1/64 1 1/4 22 1780 4 7/16 2 15/16 32 1800 6 53/64 5 1/16 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
13 1180 2 1/4 1 1/2 23 1800 4 43/64 3 1/8 35 1740 7 35/64 5 1/2 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
14 1290 2 1/2 1 3/4 24 1820 4 29/32 3 1/4 40 1610 8 3/4 6 1/2 2 13/16 - 31/4 3/4 × 3/8 3/4 2 1/4 1 1/2
15 1390 2 3/4 1 3/4 25 1830 5 5/32 3 3/8 45 1450 9 15/16 7 7/16 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4

E-158
 Maximum Hub
Dimensions
Recommended Max. Hub and Bore Sizes
American Standard No. 80 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 75 45/64 7/16 16 935 3 63/64 2 11/16 26 1165 7 13/64 5 7/16 Shaft Width x Depth Set- Setscrew Setscrew not
7 175 1 3/64 5/8 17 985 4 5/16 2 13/16 27 1170 6 33/64 5 1/2 Screw Over Key over key
8 280 1 3/8 7/8 18 1020 4 41/64 3 1/8 28 1170 7 27/32 5 13/16
9 385 1 23/32 1 3/16 19 1060 4 61/64 3 1/4 29 1165 8 5/32 6 1/8 15/16 - 1 1/4 1/4 × 1/8 1/4 3/4 1/2
10 485 2 3/64 1 1/4 20 1090 5 9/32 3 1/2 30 1160 8 31/64 6 7/16 15/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
11 580 2 3/8 1 5/8 21 1110 5 19/32 3 3/4 31 1155 8 51/64 6 1/2 17/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
12 670 2 45/64 1 3/4 22 1130 5 59/64 3 7/8 32 1143 9 7/64 6 9/16 113/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
13 750 3 1/64 2 23 1150 6 15/64 4 3/16 35 1110 10 5/64 7 1/2 25/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
14 820 3 11/32 2 1/4 24 1160 6 9/16 4 13/16 40 1020 11 43/64 8 5/8 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
15 880 3 43/64 2 3/8 25 1160 6 7/8 5 1/8 45 920 13 17/64 9 3/4 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4

American Standard No. 100 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 55 7/8 9/16 16 670 5 3 1/4 26 830 9 1/64 61/2 Shaft Width x Depth Set- Setscrew Setscrew not
7 125 1 5/16 7/8 17 700 5 13/32 3 5/8 27 835 9 13/32 67/8 Screw Over Key over key
8 200 1 47/64 1 3/16 18 730 5 51/64 3 3/4 28 830 9 13/16 75/16
9 275 2 9/64 1 3/8 19 755 6 13/64 4 3/16 29 830 10 13/64 7 1/2 15/16 - 1 3/8 5/16 × 5/32 5/16 15/16 5/8
10 350 2 9/16 1 3/4 20 775 6 39/64 4 13/64 30 825 10 39/64 7 9/16 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
11 415 2 31/32 1 15/16 21 790 7 5 1/4 31 820 11 8 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
12 475 3 3/8 2 1/4 22 805 7 13/32 5 1/2 32 815 11 13/32 8 3/8 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
13 535 3 25/32 2 1/2 23 815 7 13/16 5 13/16 35 790 12 39/64 9 1/16 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
14 585 4 3/16 2 3/4 24 825 8 13/64 6 3/16 40 730 14 19/32 .... 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4
15 630 4 19/32 3 1/16 25 830 8 39/64 6 1/2 45 655 16 19/32 .... 3 13/16 - 4 1/2 1 × 1/2 3/4 2 1/2 2

American Standard No. 120 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 40 1 1/16 11/16 16 520 6 4 26 650 10 1 3/16 7 13/64 Shaft Width x Depth Set- Setscrew Setscrew not
7 100 1 37/64 1 1/16 17 550 6 31/64 4 7/16 27 650 11 1 9/64 8 1/4 Screw Over Key over key
8 155 2 5/64 1 5/16 18 570 6 31/32 5 3/16 28 650 11 2 5/32 8 3/8
9 215 2 37/64 1 3/4 19 590 7 29/64 5 1/2 29 650 12 1/4 8 15/16 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
10 270 3 5/64 2 1/16 20 605 7 15/16 5 15/16 30 645 12 4 7/64 9 3/16 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
11 325 3 37/64 2 5/16 21 620 8 27/64 6 3/8 31 645 13 7/32 9 11/16 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
12 375 4 1/16 2 3/4 22 630 8 57/64 6 1/2 32 640 13 11/16 10 3/16 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
13 415 4 35/64 3 23 640 9 3/8 6 7/8 35 615 15 1/8 .... 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4
14 455 5 1/32 3 1/4 24 645 9 55/64 7 5/16 40 570 17 33/64 .... 3 13/16 - 4 1/2 1 × 1/2 3/4 2 1/2 2
15 490 5 33/64 3 3/4 25 650 10 11/32 7 1/2 45 515 19 5 9/64 .... 4 9/16 - 5 1/2 1 1/4 × 5/8 3/4 2 3/8 1 3/4

American Standard No. 140 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 30 1 1/4 7/8 16 380 7 1/64 5 1/4 26 475 12 5/8 9 1/8 Shaft Width x Depth Set- Setscrew Setscrew not
7 70 1 27/32 1 1/4 17 400 7 37/64 5 9/16 27 475 13 3/16 9 11/16 Screw Over Key over key
8 115 2 7/16 1 11/16 18 415 8 9/64 6 1/8 28 475 13 3/4 10 1/4
9 150 3 1/64 2 19 430 8 45/64 6 1/2 29 475 14 19/64 10 3/4 1 7/16 - 1 3/4 3/8 × 3/16 3/8 1 1/8 3/4
10 200 3 19/32 2 5/16 20 440 9 17/64 6 3/4 30 470 14 55/64 .... 1 13/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
11 235 4 11/64 2 3/4 21 450 9 53/64 7 5/16 31 470 15 27/64 .... 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
12 270 4 3/4 3 1/4 22 460 1 025/64 7 1/2 32 465 15 63/64 .... 2 15/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
13 305 5 5/16 3 9/16 23 465 1 015/16 7 15/16 35 450 17 21/32 .... 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4
14 335 5 7/8 3 7/8 24 470 11 1/2 8 1/2 40 415 20 29/64 .... 3 15/16 - 4 1/2 1 × 1/2 3/4 2 1/2 2
15 360 6 29/64 4 7/16 25 475 12 1/16 8 15/16 45 375 23 15/64 .... 4 9/16 - 5 1/2 1 1/4 × 5/8 3/4 2 3/8 1 3/4

American Standard No. 160 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 25 1 27/64 7/8 16 325 8 1/64 6 26 405 14 7/16 10 15/16 Shaft Width x Depth Set- Setscrew Setscrew not
7 60 2 7/64 1 3/8 17 340 8 21/32 6 1/2 27 405 15 5/64 .... Screw Over Key over key
8 100 2 51/64 1 3/4 18 355 9 5/16 6 13/16 28 405 15 23/32 ....
9 135 3 29/64 2 1/4 19 365 9 61/64 7 7/16 29 400 16 23/64 .... 1 3/16 - 2 1/4 1/2 × 1/4 1/2 1 1/2 1
10 170 4 1/8 2 3/4 20 375 10 19/32 7 9/16 30 400 17 .... 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
11 200 4 25/32 3 1/4 21 385 11 15/64 8 3/16 31 400 17 5/8 .... 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
12 230 5 27/64 3 5/8 22 390 11 7/8 8 7/8 32 395 18 17/64 .... 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4
13 260 6 5/64 4 1/16 23 395 12 33/64 9 35 380 20 3/16 .... 3 13/16 - 4 1/2 1 × 1/2 3/4 2 1/2 2
14 280 6 22/32 4 15/16 24 400 13 5/32 9 5/8 40 355 23 3/8 .... 4 9/16 - 5 1/2 1 1/4 × 5/8 3/4 2 3/8 1 3/4
15 305 7 3/8 5 1/2 25 400 13 51/64 10 1/4 45 320 26 9/16 .... 5 9/16 - 6 1/2 1 1/2 × 3/4 3/4 3 2

American Standard No. 200 Std. Keyway (Am. Std.) and Setscrew
No. of Max Max Max No. of Max Max Max No. of Max Max Max Min. Added To Bore For Adequate
Dia.
Teeth RPM Hub Bore Teeth RPM Hub Bore Teeth RPM Hub Bore Hub Wall Steel Sprockets
Diameter of Keyway of
6 20 1 51/64 1 1/4 16 235 10 1/32 7 1/2 26 290 18 3/64 .... Shaft Width x Depth Set- Setscrew Setscrew not
7 45 2 21/32 1 7/8 17 245 10 27/32 7 13/16 27 290 18 55/64 .... Screw Over Key over key
8 70 3 1/2 2 1/4 18 255 11 41/64 8 5/8 28 290 19 21/32 ....
9 95 4 21/64 2 13/16 19 265 12 7/16 8 15/16 29 290 20 29/64 .... 2 5/16 - 2 3/4 5/8 × 5/16 5/8 1 7/8 1 1/4
10 120 5 5/32 3 3/8 20 270 13 1/4 9 3/4 30 290 21 1/4 .... 2 13/16 - 3 1/4 3/4 × 3/8 3/4 2 1/4 1 1/2
11 145 5 63/64 3 15/16 21 280 14 3/64 10 1/2 31 400 22 3/64 .... 3 5/16 - 3 3/4 7/8 × 7/16 3/4 2 3/8 1 3/4
12 165 6 51/64 5 22 280 14 27/32 .... 32 285 22 27/32 .... 3 13/16 - 4 1/2 1 × 1/2 3/4 2 1/2 2
13 185 7 39/64 5 9/16 23 285 15 21/32 .... 35 275 25 15/64 .... 4 9/16 - 5 1/2 1 1/4 × 5/8 3/4 2 3/8 1 3/4
14 205 8 27/64 6 3/8 24 290 16 29/64 .... 40 255 29 15/64 .... 5 9/16 - 6 1/2 1 1/2 × 3/4 3/4 3 2
15 220 9 7/32 6 1/2 25 290 17 1/4 .... 45 230 33 7/32 .... 6 9/16 - 7 1/2 1 3/4 × 3/4 3/4 3 1/4 2 1/2

E-159
 Sprocket
Selection

Application Data and Selection Procedure

How to Check Horsepower Design Horsepower
Rating of Installed Drive When making drive selections consideration is given to the
1. Determine the types of driving and driven loads and obtain loads imposed on the chain. Service factors based on the type of
the proper service factor, as explained in Steps 1 and 2 under equipment to be driven (Table I, Page E162) and the type of input
power (Table II, Page E162) are used to compensate for these
2. Selection Procedures. loads.
3. Find the multiple strand factor, for the number of chain
strands in the drive, from the Multiple Strand Factor
Table, in Horsepower Tables (Page E-186 thru E-192). Horsepower Rating Tables
4. From the horsepower rating table for the chain pitch, read the The horsepower ratings in this catalog apply to lubricated single
figure under the RPM of the small sprocket and to the right pitch, single strand precision roller chains, both standard and
of the column giving number of teeth in the small sprocket. double pitch roller chain.
5. The horsepower this drive can properly transmit is as follows: The ratings reflect a service factor of 1, a chain length of
approximately 100 pitches, use of recommended lubrication
Horsepower
Drive Can =
( Rating
Horsepower ) X ( Strand )
Table Multiple methods, and a drive arrangement where two aligned sprockets
are mounted on parallel horizontal shafts.
Transmit Service Factor
The horsepower ratings relate to the speed of the smaller
sprocket and drive selections are made on this basis, whether the
drive is speed reducing or speed increasing.
Center Distance
For ratings of multiple strand roller chains refer to Multiple Strand
The following general principals should be applied in determining Factor in Horsepower Tables.
shaft center distances. The center distance must always be
greater than one-half the sum of the sprocket outside diameters
to avoid interference of teeth. When the speed ratio is greater
than 3 to 1, the center distance should be not less than the sum
Lubrication
of the sprocket diameters. Chain wrap should be at least 120° of It has been shown that a separate wedge of fluid lubricant is
the small sprocket — one-third of the teeth meshing. formed in operating chain joints much like that formed in journal
bearings. Therefore, fluid lubricant must be applied to assure
Longer center distances give greater chain wrap. For average
an oil supply to the joints and minimize metal to metal contact.
applications a center distance of 30 to 50 pitches of chain is
Lubrication, if supplied in sufficient volume, also provides
recommended for best results. For pulsating loads, a center
effective cooling and impact damping at the higher speeds. For
distance of 20 to 30 pitches may be desirable. For center
this reason, it is important that the lubrication recommendations
distances of 80 pitches or greater, idlers or chain guides should
be followed. The horsepower rating tables shown throughout this
be used to support the chain. Slightly adjustable center distances
catalog, apply only to drives lubricated in the manner specified in
will provide chain tension as the chain elongates with wear.
the tables.
Chain drives should be protected against dirt and moisture and
Alignment the oil supply kept free of contamination. Periodic oil change is
desirable. A good grade of non-detergent petroleum base oil is
Accurate alignment of shafts and sprocket tooth faces provide recommended. Heavy oils and grease are generally too stiff to
uniform distribution of the load across the entire chain width and enter and fill the chain joints.
contributes substantially to optimum drive life. Shafting, bearings,
and foundations should be suitable to maintain the initial
alignment. Periodic maintenance should include an inspection of
alignment to insure optimum chain life.

E-160
 Sprocket
Selection

Application Data and Selection Procedure

Types of Lubrication Chain and Sprocket Selection
There are four basic types of lubrication for chain drives. The Procedure Steps:
recommended type shown in the horsepower rating tables is 1. Determine class of driven load.
influenced by chain speed and the amount of power transmitted.
These are minimum lubrication requirements and the use of a 2. Select service factor.
better type (for example, Type C instead of Type B) is acceptable 3. Calculate design horsepower.
and may be beneficial. Chain life can vary appreciably depending
4. Select chain pitch.
upon the way the drive is lubricated. The better the lubrication,
the longer the chain and sprocket life. For this reason, it is 5. Select number of teeth in small sprocket.
important that the lubrication recommendations be followed when 6. Determine number of teeth in larger sprocket.
using the rating tables given in this catalog.
7. Determine center distance.
8. Calculate chain length.
Lubrication
TYPE A — Manual Lubrication. Oil applied periodically with
brush or spout can. Drive Positions
TYPE B — Oil Bath or Oil Slinger. Oil level maintained in casing
at predetermined height.
TYPE C — Oil Stream. Oil supplied by circulating pump inside
chain loop on lower span.
NOTE: Drip Lubrication. Oil applied between link plate edges from
a drip lubricator and should be used in clean environments only.

Selection of Roller Chain Drives Good Permissible

The following information is necessary for the proper selection
and design of roller chain drives:
1. Type of input horsepower (electrical motor, internal
combustion engine.)
2. Type of equipment to be driven.
3. Horsepower to be transmitted.
4. Full load speed of the fastest running shaft. (RPM)
5. Desired speed of the slow speed shaft. (RPM)
6. Diameters of the driving and driven shafts. Avoid Except with
Avoid
7. Center to center distance of shafts. Adjustable Centers
8. Position of drive and space limitations.
9. Method of lubrication.
10. Conditions of drive, steady or fluctuating load, hours of
operation, lubrication.
Most roller chain drive applications allow considerable latitude in
the selection of sprocket sizes and chain pitch, although usually
one combination will best fulfill the requirements of power, speed,
space limitations and economy.

E-161
 Sprocket
Selection

Application Data and Selection Procedure

Step I Step III
Service Classification — Table I Determination of Design Horsepower
Uniform Load Determine the design horsepower of the required drive using the
• Agitators, Liquid • Generators following procedure.
• Blowers, Centrifugal • Line Shafts, Even Load 1. Determine Service Classification — Table I. Unlisted equipment
• Conveyors, Even Load • Machines, Even Load, may be classified by its similarity to a listed type.
• Elevators, Even Load Non-reversing
2. Using Service Classification and Frequency of Service, select the
• Fans, Centrifugal • Pumps, Centrifugal
Service Factor — Table II. Increase the Service Factor by adding
Moderate Shock Load compensation for unfavorable operating conditions.
3. Multiply the normal operating horsepower of the drive by the
• Moderate Shock Load • Laundry - Washers and Tumblers
Compensated Service Factor to obtain Service Horsepower.
• Beaters • Line Shafts, Uneven Load
• Compressors, Centrifugal • Machines, Pulsating
• Conveyors, Uneven Load Load, Non-reversing Step IV
• Elevators, Uneven Load • Pumps, Reciprocating, Triplex
• Grinders, Pulp • Screens, Rotary, Even Load Drive Selection
• Kilns and Dryers • Woodworking Machinery Using Design Horsepower computed above, use Trial Selection
Chart (Horsepower Tables) on page E184-E185, or enter tables of
Heavy Shock Load Horsepower Ratings shown on pages E186 thru E192. Select the
• Brick Machines • Mills, Hammer, Rolling or Drawing smallest pitch chain which has the required horsepower rating for
• Compressors Reciprocating • Presses a pinion sprocket turning at the specified RPM. Check to be certain
the selected sprocket has a listed maximum bore large enough
• Crushers • Pumps, Reciprocating, to accommodate the specified shaft. The tables on pages E-158
• Machines, Reversing Simplex or Duplex thru E-159 gives maximum bores for the usual range of driving
or Impact Loads sprockets.
If the Design Horsepower at the required RPM is greater than the
Step II horsepower rating of the largest pitch chain which can operate
at that speed, a multiple chain drive should be considered for the
Service Factor — Table II application.
Type of Input Power Selection of drives to operate at speeds somewhat below the
Internal Internal maximum rating will increase the life of the drive and quietness of
Service Electric operation.
Combustion Combustion
Classification Motor
Engine with Engine with
or
Hydraulic Mechanical
Drive
Turbine
Drive Step V
Uniform Load 1.0 1.0 1.2
Driving Sprocket
Moderate Shock Load 1.2 1.3 1.4
In selecting the driving sprocket 17 teeth are recommended as
Heavy Shock Load 1.4 1.5 1.7
a minimum although 15 teeth are quite often used, and as low
Unfavorable Operating Conditions which may be present should as 7 teeth can be cut. When the maximum bore of the 17 tooth
be compensated for by adding .2 to the Service Factor for each sprocket will not accommodate the driving shaft, it is necessary to
unfavorable condition. Some of these conditions are listed below: go to a sprocket with a greater number of teeth. Hardened teeth are
1. Multiple Shafts — add .2 for each additional shaft. recommended for sprockets with 25 teeth or less.
2. Excessive speed ratios — exceeding 7 to 1.
3. Heavy starting loads with frequent starts and stops.
4. Conditions of high temperatures, unusually abrasive conditions,
or circumstances decreasing lubrication effectiveness or not
allowing the use of recommended lubrication procedures.

E-162
 Sprocket
Selection

Application Data and Selection Procedure

Step VI Chain Drive Design Example
To select a roller chain drive from a 10 HP electric motor (1.625'' shaft)
Driven Sprocket (Ratio) 1200 RPM (1150 under load) to a wood working machine shaft at 300
RPM on 30" centers. Drive conditions — moderate pulsating load, good
The number of teeth selected for the driven sprocket depends upon
lubrication, 10 hour day operation.
the driving sprocket chosen and the desired speed of the driven
shaft. When space limitations are a factor, the diameter of the driven 1. Service class — moderate shock load (Table I).
sprocket sometimes determines the final selection of drive. 2. Service factor — 1.3 (Table II).
The recommended maximum speed ratio is 7 to 1, although higher 3. Design HP — 1.3 × 10 = 13 DHP.
ratios are occasionally used. It is usually better design, however, for
4. Selection — The Horsepower Ratings on page E-184 show that either
large reductions to use a double reduction drive.
of the following combinations may be used.
Select the driven sprocket size from the Speed Ratio Table on page
No. D40-19 Tooth — Smoothest in operation
E-170 using the required speed ratio and size of driver sprocket.
No. 50-18 Tooth — Lower drive cost
For our purpose we select No. 50 chain and checking the bore find
Step VII that the 1.625" shaft can be accommodated with a stock bored to size
sprocket.
Shaft Centers The driven sprocket is found as follows:
May be calculated from the formula on page E-168 where the No. Teeth
sprocket diameters and chain length are known. = 18 × 1150 (Ratio) = 68.99 or 69 Teeth
Driven Sprocket
300
On many applications the motor base is adjustable, allowing for
slight changes in shaft centers. On long centers some form of chain Since 69 teeth is not a stock size we select 70 teeth. The chain length is
adjuster or take-up is recommended. calculated as shown on page E-169 and is 142 pitches.

Step VIII Overhung Load

When a sprocket is mounted on a reducer shaft, a calculation should be
Chain Length made to determine the overhung load in pounds using formula on page
On page E-168 is shown a simple method of computing the length i-2 in general engineering section.
of chain necessary for a drive with given sprocket dimensions and
center to center distance of shafts. (See chart on page E-169 for
length in ft.)

E-163
 Sprocket
Engineering

Engineering Data & Design

Horsepower equals 33,000 foot pounds per minute, or 550 foot Factor of Safety is determined as follows:
pounds per second. In terms of chain load and speed.

FS = Chain Ultimate Strength

HP = Working Load × Ft. Per Min. Chain Working Load
33,000

or HP = Working Load × T × P × RPM Shaft Torque ordinarily is greater for the driven shaft
396,000 than for the driving shaft due to the difference in sprocket sizes
and RPM Torque is usually expressed in inch pounds.
Where T = number of sprocket teeth
P = chain pitch Torque HP × 63,000
=
(Driving Shaft)
RPM

Chain Working Load when the horsepower input is known Torque

(Driven Shaft)
=
Working Load × R
and the chain working load is desired, this can be calculated as follows:

Working Load = HP x 33,000

Ft. Per Min.

or = HP x 396,000
T × P × RPM
Where a crank arm is used the load transmitted by
the arm can be determined as follows:

Chain Speed can be determined from the following formula:

Crank Arm Load = Driven Shaft Torque
Chain Speed r
= T × RPM
(Ft. Per Min.)
K
or = Chain Working Load × R
Where T = number of sprocket teeth r
Constant K (Pitches of Chain Per Foot)

PITCH 3/8" 1/2" 5/8" 3/4" 1" 1 1/4" 1 1/2" 1 3/4" 2" 2 1/2" 3"
K 32 24 19.2 16 12 9.6 8 6.85 6 4.8 4
Catenary Tension imposed by reason of the
weight of chain can be approximated as follows:

W×L
Approx. Wt./Ft. of Standard Roller Chain Catenary Tension = + (W × S)
8×S
Number Single Double Triple Quadruple
25 0.08 0.18 0.27 0.35 Where W = weight of chain (lbs. per ft.)
35 0.23 0.46 0.69 0.92
41 0.28 — — — S = chain sag (feet) = 2% to 3%
40 0.41 0.82 1.23 1.64 of shaft centers approx.
50 0.69 1.38 2.07 2.76
60 1.04 2.08 3.12 4.16 L = Shaft center in feet.
80 1.77 3.54 5.31 7.08
100 2.59 5.18 7.77 10.36
120 4.05 8.10 12.15 16.20
140 5.10 10.20 15.30 20.40
160 6.85 13.70 20.55 27.40
180 9.30 18.20 27.20 36.30
200 10.20 21.00 31.50 42.00
240 16.90 33.40 50.00 66.50

E-164
 Sprocket
Engineering

Engineering Data & Design

Conveyor Chains Chain Pull
Chains used in the design of conveyors should be selected on the basis The force or pull required to move a conveyor includes the pull
of the chain pull imposed by the application and the permissible or necessary to move the weight of chain and material and the frictional
maximum working load of the chain. resistance of the chain parts on the runways. The following formulas
may be used in calculating the total chain pull. The same formula applies
In some instances a larger pitch chain than is necessary may be selected
in the case of single or parallel strand chain conveyors, but in the case
due to the desired attachment spacing, and the effect in this case would
of parallel strand conveyors, the pull per chain is one-half of the figure
be to increase the life of the conveyor.
calculated from the formula.
Horizontal Conveyors
Inclined Conveyors

Total pull of chains = f H (W + P)

NOTE: When lower strand of conveyor drags on runway

above formula becomes f H (W + 2P).

Vertical Conveyors

Total pull of chains =

V (W + P) Total pull of chains = f H (W + P) + V (W + P)
NOTE: When lower strand of conveyor drags on runway
the factor P (f H – V) should be added to above
formula unless V is greater than f H.

H (ft) = Horizontal projection of conveyor length.

V (ft) = Vertical projection of conveyor length.
Value of Coefficient F
W (lb) = Weight of material handled per foot of conveyor length. Sliding steel on iron or steel...............................................................25%
P (lb) = Weight per foot of all moving conveyor Rolling friction....................................................................................15%
parts (single or two strand).
(If material or other than the usual chain parts are in contact with the
f = Coefficient of friction of chain on runway.
runway, the coefficient should be increased to compensate for the added
resistance.)

E-165
 Sprocket
Engineering

Chain Drive Selection

Step 1:

Prime Driver:
Type & Description Rated - HP RPM
Driven Comp:
Type & Description RPM Hours/Day
Center Distance: " " "
Maximum Minimum Nominal

Step 2:
Service Classification (Step I Page E-162)

Step 3: (Include additions to basic factor)

(Step II Page E-162)
Service Factor

Step 4: Determine Design HP

× =
HP Service Factor HP Design

Step 5: Speed Ratio

× =
RPM Faster Shaft RPM Slower Shaft Ratio (E-172)

Step 6: From selector chart, select proper chain pitch & driver sprocket. (Check Martin Catalog page E-184.)

A. B. C.
Chain Pitch Driver Sprocket Maximum Bore
(Pages E-16 thru E-112)

Step 7: From ratio chart, select proper driven sprocket.

C.
Driven Sprocket Maximum Bore

Step 8: Check manufacturer’s catalog for maximum bore recommended & final stock selection. (Pages E-16 thru E-112)

Step 9: Review Horsepower table for type of lubrication required.

Type: A B C (Pages E-161 and E-186 thru E-192)

OR Type: 1 2 3 (Pages E-191 and E-192)

Step 10:
÷
Center Dist. (inches) Chain Pitch Center Dist. (pitches)

N+n A
Step 11: Formula for chain length = 2C + +
2 C

Where: C = Center Dist. in pitches

N = Number of teeth in Driven Sprocket
n = Number of teeth in Driver Sprocket
A = Value from table tabulated for N - n values

E-166
 Sprocket
Hardening

Brinell, Rockwell and Scleroscope Material

Hardness Numbers with Corresponding All Martin stock sprockets are made of quality steel poured to our speci-
fications.
Tensile Strength
Bar size sprockets normally include sizes up to 7" or 71/2" in diameter
Brinell Rockwell “C” Scleroscope Tensile Strength type “B”, “BS”, “QD”, “TB” single, double & triple width. And can easily
10 MM Ball 120 Cone Shore 1000 Lb. be electrical induction or flame hardened — to Rockwell “C” 40 to 50.
3,000 Kg. 150 Kg. Model C Per Sq. In.
745 68 100 368 Plate sprockets normally include sizes 71/2" in diameter and larger
712 66 95 352 type “B”, “BS”, “C”, “QD”, “TB” single, double, & triple width fabricated
682 64 91 337 and type “A” all diameters. This material would have 35 to 40 points of
653 62 87 324 carbon and can be induction or flame hardened to Rockwell “C” 30 to 45.
627 60 84 311
Degree of hardness obtainable and method depends on size of sprocket.
601 58 81 298
578 57 78 287 Special quality steel can be used for large quantities or made-to-order
555 55 75 276 sprockets if specified.
534 53 72 266
514 52 70 256
495 50 67 247
477
461
49
47
65
63
238
229
Hardening Recommendations
444 46 61 220 Hardened teeth substantially increases sprocket life and is recommended
429 45 59 212 under conditions listed below:
415 44 57 204
401 42 55 196 1. Pinion or driver where the reduction is 4:1 or greater.
388 41 54 189
375 40 52 182 2. Slow speed drives (100 FPM or less).
362 38 51 176 3. Where safety factor is less than standard.
351 37 49 170
341 36 48 165 4. Unusual abrasive conditions.
331 35 46 160
321 34 45 155 Degree of hardness — this is governed by conditions prevailing each
311 33 44 150 application — for stock sprockets these general suggestions may be
302 32 43 146 used as guide lines:
293 31 42 142
285 30 40 138 1. Rockwell “C” 35 to 50 pinion or driver.
277 29 39 134
269 28 38 131 2. Rockwell “C” 25 to 40 larger diameter or driver sprockets.
262 26 37 128 Induction or flame hardening will be used as best suited to the individual
255 25 37 125
248 24 36 122
application. The diameter and pitch of the sprocket govern the method
241 23 35 119 used.
235 22 34 116 Caution should be used to avoid “file hardness” (Rockwell C 62 and
229 21 33 113
223 20 32 110 above) as it is not recommended for sprockets due to brittleness.
Rockwell “B” Depth of hardening should be limited so as to provide case only on the
1/16" Ball wear surfaces with a tough resilient core to absorb shock — (see illus-
100 Kg. tration tooth section).
217 97 31 107
212 96 31 104
207 95 30 101
202 94 30 99
197 93 29 97
192 92 28 95
187 91 28 93
183 90 27 91
179 89 27 89
174 88 26 87

Note: Hardening cannot be accurately checked with a file —

stationary or portable hardness testers should be used for
conclusive results. Hardened Tooth Section Depth of Hardness Required

E-167
 Chain Drive
Engineering

Chain Length Calculation

The following equation may be used to determine the chain length required for any two-sprocket drive.

N+n .1013 (N – n)2 .1013 (N – n)2 N+n A

L = 2C + + or substituting A for , L = 2C + +
2 4C 4C 2 C

Where:

C = Shaft Center Distance in pitches

L = Length of chain in pitches
N = Number of teeth in larger sprocket
n = Number of teeth in smaller sprocket
π = 3.1416
A = Value from table below tabulated for values of N-n
P = Pitch of chain CENTER DISTANCE

NOTE: The method described with above table of constants is sufficiently accurate for practically all commercial chain drives. When, however, a high
degree of precision is necessary, especially if the drive is vertical, the following formula is useful in determining the exact centers for chain length
already determined.

Calculation of shaft centers

{ }
P
The following formula is useful in determining the approximate
centers in inches for chain lengths in pitches already determined.
C =
8
2L – N – n + √ (2L - N -n) - 0.810 (N - n)
2 2

Values of A For Chain Length Calculation

N-n A N-n A N-n A N-n A N-n A N-n A
1 0.03 32 25.94 63 100.54 94 223.82 125 395.79 156 616.44
2 0.10 33 27.58 64 103.75 95 228.61 126 402.14 157 624.37
3 0.23 34 29.28 65 107.02 96 233.44 127 408.55 158 632.35
4 0.41 35 31.03 66 110.34 97 238.33 128 415.01 159 640.38
5 0.63 36 32.83 67 113.71 98 243.27 129 421.52 160 648.46
6 0.91 37 34.68 68 117.13 99 248.26 130 428.08 161 656.59
7 1.24 38 36.58 69 120.60 100 253.30 131 434.69 162 664.77
8 1.62 39 38.53 70 124.12 101 258.39 132 441.36 163 673.00
9 2.05 40 40.53 71 127.69 102 263.54 133 448.07 164 681.28
10 2.53 41 42.58 72 131.31 103 268.73 134 454.83 165 689.62
11 3.06 42 44.68 73 134.99 104 273.97 135 461.64 166 698.00
12 3.65 43 46.84 74 138.71 105 279.27 136 468.51 167 706.44
13 4.28 44 49.04 75 142.48 106 284.67 137 475.42 168 714.92
14 4.96 45 51.29 76 146.31 107 290.01 138 482.39 169 723.46
15 5.70 46 53.60 77 150.18 108 295.45 139 489.41 170 732.05
16 6.48 47 55.95 78 154.11 109 300.95 140 496.47 171 740.68
17 7.32 48 58.36 79 158.09 110 306.50 141 503.59 172 749.37
18 8.21 49 60.82 80 162.11 111 312.09 142 510.76 173 758.11
19 9.14 50 63.33 81 166.19 112 317.74 143 517.98 174 766.90
20 10.13 51 65.88 82 170.32 113 323.44 144 525.25 175 775.74
21 11.17 52 68.49 83 174.50 114 329.19 145 532.57 176 784.63
22 12.26 53 71.15 84 178.73 115 334.99 146 539.94 177 793.57
23 13.40 54 73.86 85 183.01 116 340.84 147 547.36 178 802.57
24 14.59 55 76.62 86 187.34 117 346.75 148 554.83 179 811.61
25 15.83 56 79.44 87 191.73 118 352.70 149 562.36 180 820.70
26 17.12 57 82.30 88 196.16 119 358.70 150 569.93 181 829.85
27 18.47 58 85.21 89 200.64 120 364.76 151 577.56 182 839.04
28 19.86 59 88.17 90 205.18 121 370.86 152 585.23 183 848.29
29 21.30 60 91.19 91 209.76 122 377.02 153 592.96 184 857.58
30 22.80 61 94.25 92 214.40 123 383.22 154 600.73 185 866.93
31 24.34 62 97.37 93 219.08 124 389.48 155 608.56
E-168
 Chain Drive
Engineering
Roller Chain Lengths
Chain Pitch – Inches
No. of Pitches 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 1 3/4 2 2 1/2 3
Chain Length – Feet
1 0.0313 0.0417 0.0521 0.0625 0.0833 0.1042 0.1250 0.1458 0.1667 0.2083 0.2500
2 0.0625 0.0833 0.1042 0.1250 0.1667 0.2083 0.2500 0.2917 0.3333 0.4167 0.5000
3 0.0938 0.1250 0.1563 0.1875 0.2500 0.3125 0.3750 0.4375 0.5000 0.6250 0.7500
4 0.1250 0.1667 0.2083 0.2500 0.3333 0.4167 0.5000 0.5833 0.6667 0.8333 1.0000
5 0.1563 0.2083 0.2604 0.3125 0.4167 0.5208 0.6250 0.7292 0.8333 1.0417 1.2500
6 0.1875 0.2500 0.3125 0.3750 0.5000 0.6250 0.7500 0.8750 1.0000 1.2500 1.5000
7 0.2188 0.2917 0.3646 0.4375 0.5833 0.7292 0.8750 1.0208 1.1667 1.4583 1.7500
8 0.2500 0.3333 0.4167 0.5000 0.6667 0.8333 1.0000 1.1667 1.3333 1.6667 2.0000
9 0.2813 0.3750 0.4688 0.5625 0.7500 0.9375 1.1250 1.3125 1.5000 1.8750 2.2500
10 0.3125 0.4167 0.5208 0.6250 0.8333 1.0417 1.2500 1.4583 1.6667 2.0833 2.5000
11 0.3438 0.4584 0.5729 0.6875 0.9167 1.1459 1.3750 1.6041 1.8333 2.9217 2.7500
12 0.3750 0.5000 0.6250 0.7500 1.0000 1.2500 1.5000 1.7500 2.000 2.5000 3.0000
13 0.4063 0.5417 0.6771 0.8125 1.0833 1.3542 1.6250 1.8958 2.1667 2.7083 3.2500
14 0.4375 0.5833 0.7292 0.8750 1.1667 1.4583 1.7500 2.0417 2.3333 2.9167 3.5000
15 0.4688 0.6250 0.7813 0.9375 1.2500 1.5625 1.8750 2.1875 2.5000 3.1250 3.7500
16 0.5000 0.6667 0.8333 1.0000 1.3333 1.6667 2.0000 2.3333 2.6667 3.3333 4.0000
17 0.5313 0.7084 0.8854 1.0625 1.4167 1.7709 2.1250 2.4791 2.8333 3.5417 4.2500
18 0.5625 0.7500 0.9375 1.1250 1.5000 1.8750 2.2500 2.6250 3.0000 3.7500 4.5000
19 0.5938 0.7917 0.9896 1.1875 1.5833 1.9792 2.3750 2.7708 3.1667 3.9583 4.7500
20 0.6250 0.8333 1.0417 1.2500 1.6667 2.0833 2.5000 2.9167 3.3333 4.1667 5.0000
21 0.6563 0.8750 1.0938 1.3125 1.7500 2.1875 2.6250 3.0625 3.5000 4.3750 5.2500
22 0.6875 0.9167 1.1458 1.3750 1.8333 2.2917 2.7500 3.2083 3.6667 4.5833 5.5000
23 0.7188 0.9584 1.1979 1.4375 1.9166 2.3959 2.8750 3.3541 3.8333 4.7917 5.7500
24 0.7500 1.0000 1.2500 1.5000 2.0000 2.5000 3.0000 3.5000 4.0000 5.0000 6.0000
25 0.7813 1.0417 1.3021 1.5625 2.0833 2.6042 3.1250 3.6458 4.1667 5.2083 6.2500
26 0.8125 1.0833 1.3541 1.6250 2.1667 2.7083 3.2500 3.7917 4.3333 5.3167 6.5000
27 0.8438 1.1250 1.4062 1.6875 2.2500 2.8125 3.3750 3.9375 4.5000 5.6250 6.7500
28 0.8750 1.1667 1.4583 1.7500 2.3333 2.9167 3.5000 4.0833 4.6667 5.8333 7.0000
29 0.9063 1.2084 1.5104 1.8125 2.4167 3.0209 3.6250 4.2291 4.8333 6.0417 7.2500
30 0.9375 1.2500 1.5625 1.8750 2.5000 3.1250 3.7500 4.3750 5.0000 6.2500 7.5000
31 0.9688 1.2917 1.6146 1.9375 2.5833 3.2292 3.8750 4.5208 5.1667 6.4583 7.7500
32 1.0000 1.3333 1.6667 2.0000 2.6667 3.3333 4.0000 4.6667 5.3333 6.6667 8.0000
33 1.0313 1.3750 1.7188 2.0625 2.7500 3.4375 4.1250 4.8125 5.5000 6.8750 8.2500
34 1.0625 1.4167 1.7708 2.1250 2.8333 3.5417 4.2500 4.9583 5.6667 7.0833 8.5000
35 1.0938 1.4584 1.8229 2.1875 2.9167 3.6459 4.3750 5.1041 5.8333 7.2917 8.7500
36 1.1250 1.5000 1.8750 2.2500 3.0000 3.7500 4.5000 5.2500 6.0000 7.5000 9.0000
37 1.1563 1.5417 1.9271 2.3125 3.0833 3.8542 4.6250 5.3958 6.1667 7.7083 9.2500
38 1.1875 1.5833 1.9791 2.3750 3.1667 3.9583 4.7500 5.5417 6.3333 7.9167 9.5000
39 1.2188 1.6250 2.0312 2.4375 3.2500 4.0625 4.8750 5.0875 6.5000 8.1250 9.7500
40 1.2500 1.6667 2.0833 2.5000 3.3333 4.1667 5.0000 5.8333 6.6667 8.3333 10.0000
41 1.2813 1.7084 2.1354 2.5625 3.4167 4.2709 5.1250 5.9791 6.8333 8.5417 10.2500
42 1.3125 1.7500 2.1875 2.6250 3.5000 4.3750 5.2500 6.1250 7.0000 8.7500 10.5000
43 1.3438 1.7917 2.2396 2.6875 3.5833 4.4792 5.3750 6.2708 7.1667 8.9583 10.7500
44 1.3750 1.8333 2.2916 2.7500 3.6667 4.5833 5.5000 6.4167 7.3333 9.1667 11.0000
45 1.4063 1.8750 2.3437 2.8125 3.7500 4.6875 5.6250 6.5625 7.5000 9.3750 11.2500
46 1.4375 1.9167 2.3958 2.8750 3.8333 4.7917 5.7500 6.7083 7.6667 9.5833 11.5000
47 1.4688 1.9584 2.4479 2.9375 3.9167 4.8959 5.8750 6.8541 7.8333 9.7917 11.7500
48 1.5000 2.0000 2.5000 3.0000 4.0000 5.0000 6.0000 7.0000 8.0000 10.0000 12.0000
49 1.5313 2.0417 2.5521 3.0625 4.0833 5.1042 6.1250 7.1458 8.1667 10.0283 12.2500
50 1.5625 2.0833 2.6042 3.1250 4.1667 5.2083 6.2500 7.2917 8.3333 10.4167 12.5000
51 1.5938 2.1250 2.6563 3.1875 4.2500 5.3125 6.3750 7.4375 8.5000 10.6250 12.7500
52 1.6250 2.1667 2.7083 3.2500 4.3333 5.4167 6.5000 7.5833 8.6667 10.8333 13.0000
53 1.6563 2.2084 2.7604 3.3125 4.4167 5.5209 6.6250 7.7291 8.8333 11.0417 13.2500
54 1.6875 2.2500 2.8125 3.3750 4.5000 5.6250 6.7500 7.8750 9.0000 11.2500 13.5000
55 1.7188 2.2917 2.8647 3.4375 4.5833 5.7292 6.8750 8.0208 9.1667 11.4583 13.7500
56 1.7500 2.3333 2.9167 3.5000 4.6667 5.8333 7.0000 8.1667 9.3333 11.6667 14.0000
57 1.7813 2.3750 2.9688 3.5625 4.7500 5.9375 7.1250 8.3125 9.5000 11.8750 14.2500
58 1.8125 2.4167 3.0208 3.6250 4.8333 6.0417 7.2500 8.4583 9.6667 12.0833 14.5000
59 1.8438 2.4584 3.0729 3.6875 4.1967 6.1459 7.3750 8.6041 9.8333 12.2917 14.7500
60 1.8750 2.5000 3.1250 3.7500 5.0000 6.2500 7.5000 8.7500 10.0000 12.5000 15.0000
61 1.9063 2.5417 3.1771 3.8125 5.0833 6.3542 7.6250 8.8958 10.1667 12.7083 15.2500
62 1.9375 2.5833 3.2292 3.8750 5.1667 6.4583 7.7500 9.0417 10.3333 12.9167 15.5000
63 1.9688 2.6250 3.2813 3.9375 5.2500 6.5625 7.8750 9.1875 10.5000 13.1250 15.7500
64 2.0000 2.6667 3.3333 4.0000 5.3333 6.6667 8.0000 9.3333 10.6667 13.3333 16.0000
65 2.0313 2.7084 3.3854 4.0625 5.4167 6.7709 8.1250 9.4791 10.8333 13.5417 16.2500
66 2.0625 2.7500 3.4375 4.1250 5.5000 6.8750 8.2500 9.6250 11.0000 13.7500 16.5000
67 2.0938 2.7917 3.4897 4.1875 5.5833 6.9792 8.3750 9.7708 11.1667 13.9583 16.7500
68 2.1250 2.8333 3.5417 4.2500 5.6667 7.0883 8.5000 9.9167 11.3333 14.1667 17.0000
69 2.1563 2.8750 3.5938 4.3125 5.7500 7.1875 8.6250 10.0625 11.5000 14.3750 17.2500
70 2.1875 2.9167 3.6458 4.3750 5.8333 7.2917 8.7500 10.2083 11.6667 14.5833 17.5000
71 2.2188 2.9584 3.6979 4.4375 5.9167 7.3959 8.8750 10.3541 11.8333 14.7917 17.7500
72 2.2500 3.0000 3.7500 4.5000 6.0000 7.5000 9.0000 10.5000 12.0000 15.0000 18.0000
73 2.2813 3.0417 3.8021 4.5625 6.0833 7.6042 9.1250 10.6458 12.1667 15.2083 18.2500
74 2.3125 3.0833 3.8541 4.6250 6.1667 7.7083 9.2500 10.7917 12.3333 15.4167 18.5000
75 2.3438 3.1250 3.9062 4.6875 6.2500 7.8125 9.3750 10.9375 12.5000 15.6250 18.7500
80 2.5000 3.3333 4.1667 5.0000 6.6667 8.3333 10.0000 11.6667 13.3333 16.6667 20.0000
85 2.6563 3.5417 4.4271 5.3125 7.0833 8.8542 10.6250 12.3958 14.1667 17.7083 21.2500
90 2.8125 3.7500 4.6875 5.6250 7.5000 9.3750 11.2500 13.1250 15.0000 18.7500 22.5000
95 2.9688 3.9584 4.9479 5.9375 7.9167 9.8959 11.8750 13.8541 15.8333 19.7917 23.7500
100 3.1250 4.1667 5.2083 6.2500 8.3333 10.4167 12.5000 14.5833 16.6667 20.8333 25.0000

E-169
 Chain Drive
Engineering

Speed Ratios For Sprocket Combinations Driver Sprocket Teeth

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
9 1.00
10 1.11 1.00
11 1.22 1.10 1.00
12 1.33 1.20 1.09 1.00
13 1.44 1.30 1.18 1.08 1.00
14 1.56 1.40 1.27 1.17 1.08 1.00
15 1.67 1.50 1.36 1.25 1.15 1.07 1.00
16 1.78 1.60 1.45 1.33 1.23 1.14 1.07 1.00
17 1.89 1.70 1.55 1.42 1.31 1.21 1.13 1.06 1.00
18 2.00 1.80 1.64 1.50 1.38 1.29 1.20 1.13 1.06 1.00
19 2.11 1.90 1.73 1.58 1.46 1.36 1.27 1.19 1.12 1.06 1.00
20 2.22 2.00 1.82 1.67 1.54 1.43 1.33 1.25 1.18 1.11 1.05 1.00
21 2.33 2.10 1.91 1.75 1.61 1.50 1.40 1.31 1.23 1.17 1.10 1.05 1.00
22 2.44 2.20 2.00 1.83 1.69 1.57 1.47 1.38 1.29 1.22 1.16 1.10 1.05 1.00
23 2.56 2.30 2.09 1.92 1.77 1.64 1.53 1.44 1.35 1.28 1.21 1.15 1.09 1.04 1.00
24 2.67 2.40 2.18 2.00 1.85 1.71 1.60 1.50 1.41 1.33 1.26 1.20 1.14 1.09 1.04 1.00
25 2.78 2.50 2.27 2.08 1.92 1.79 1.67 1.56 1.47 1.39 1.32 1.25 1.19 1.14 1.09 1.04 1.00
26 2.89 2.60 2.36 2.17 2.00 1.86 1.73 1.63 1.53 1.45 1.37 1.30 1.24 1.18 1.13 1.08 1.04 1.00
27 3.00 2.70 2.45 2.25 2.08 1.93 1.80 1.69 1.59 1.50 1.42 1.35 1.29 1.23 1.17 1.12 1.08 1.04
28 3.11 2.80 2.54 2.33 2.15 2.00 1.87 1.75 1.65 1.56 1.47 1.40 1.33 1.27 1.22 1.17 1.12 1.08
29 3.22 2.90 2.64 2.42 2.23 2.07 1.93 1.81 1.71 1.61 1.53 1.45 1.38 1.32 1.26 1.21 1.16 1.12
30 3.33 3.00 2.73 2.50 2.31 2.14 2.00 1.88 1.76 1.67 1.58 1.50 1.43 1.36 1.31 1.25 1.20 1.15
31 3.44 3.10 2.82 2.58 2.38 2.21 2.07 1.94 1.82 1.72 1.63 1.55 1.48 1.41 1.35 1.29 1.24 1.19
32 3.56 3.20 2.91 2.67 2.46 2.28 2.13 2.00 1.88 1.78 1.68 1.60 1.52 1.45 1.39 1.33 1.28 1.23
33 3.67 3.30 3.00 2.75 2.54 2.36 2.20 2.06 1.94 1.83 1.74 1.65 1.57 1.50 1.43 1.38 1.32 1.27
34 3.78 3.40 3.09 2.83 2.62 2.43 2.27 2.13 2.00 1.89 1.79 1.70 1.62 1.55 1.48 1.42 1.36 1.31
35 3.89 3.50 3.18 2.92 2.69 2.50 2.33 2.19 2.06 1.95 1.84 1.75 1.67 1.59 1.52 1.46 1.40 1.34
36 4.00 3.60 3.27 3.00 2.77 2.57 2.40 2.25 2.12 2.00 1.89 1.80 1.71 1.63 1.57 1.50 1.44 1.38
Driven Sprocket Teeth

37 4.11 3.70 3.36 3.08 2.85 2.64 2.47 2.31 2.18 2.06 1.95 1.85 1.76 1.68 1.61 1.54 1.48 1.42
38 4.22 3.80 3.45 3.17 2.92 2.71 2.53 2.38 2.24 2.11 2.00 1.90 1.81 1.73 1.65 1.58 1.52 1.46
39 4.33 3.90 3.55 3.25 3.00 2.79 2.60 2.44 2.29 2.17 2.05 1.95 1.86 1.77 1.70 1.63 1.56 1.50
40 4.44 4.00 3.64 3.33 3.08 2.86 2.67 2.50 2.35 2.22 2.10 2.00 1.90 1.82 1.74 1.67 1.60 1.54
41 4.56 4.10 3.73 3.42 3.15 2.93 2.73 2.56 2.41 2.28 2.16 2.05 1.95 1.86 1.78 1.71 1.64 1.58
42 4.67 4.20 3.82 3.50 3.23 3.00 2.80 2.63 2.47 2.34 2.21 2.10 2.00 1.91 1.83 1.75 1.68 1.61
43 4.78 4.30 3.91 3.58 3.31 3.07 2.87 2.69 2.53 2.39 2.26 2.15 2.05 1.95 1.87 1.79 1.72 1.65
44 4.89 4.40 4.00 3.67 3.39 3.14 2.93 2.75 2.59 2.44 2.32 2.20 2.10 2.00 1.91 1.83 1.76 1.69
45 5.00 4.50 4.09 3.75 3.46 3.21 3.00 2.81 2.65 2.50 2.37 2.25 2.14 2.04 1.96 1.88 1.80 1.73
46 5.11 4.60 4.18 3.83 3.54 3.29 3.07 2.88 2.71 2.56 2.42 2.30 2.19 2.09 2.00 1.92 1.84 1.77
47 5.22 4.70 4.27 3.92 3.62 3.36 3.13 2.94 2.76 2.61 2.47 2.35 2.24 2.14 2.04 1.96 1.88 1.81
48 5.33 4.80 4.36 4.00 3.69 3.43 3.20 3.00 2.82 2.67 2.52 2.40 2.28 2.18 2.09 2.00 1.92 1.84
49 5.44 4.90 4.45 4.08 3.77 3.50 3.27 3.06 2.88 2.72 2.58 2.45 2.33 2.23 2.13 2.04 1.96 1.88
50 5.56 5.00 4.55 4.17 3.85 3.57 3.33 3.13 2.94 2.78 2.63 2.50 2.38 2.27 2.17 2.08 2.00 1.92
51 5.67 5.10 4.64 4.25 3.92 3.64 3.40 3.19 3.00 2.83 2.68 2.55 2.43 2.32 2.22 2.13 2.04 1.96
52 5.78 5.20 4.73 4.33 4.00 3.71 3.47 3.25 3.06 2.89 2.74 2.60 2.48 2.36 2.26 2.17 2.08 2.00
53 5.89 5.30 4.82 4.42 4.08 3.79 3.53 3.31 3.12 2.94 2.79 2.65 2.52 2.41 2.30 2.21 2.12 2.04
54 6.00 5.40 4.91 4.50 4.15 3.86 3.60 3.38 3.18 3.00 2.84 2.70 2.57 2.45 2.35 2.25 2.16 2.07
55 6.11 5.50 5.00 4.58 4.23 3.93 3.67 3.44 3.24 3.06 2.90 2.75 2.62 2.50 2.39 2.29 2.20 2.12
56 6.22 5.60 5.09 4.67 4.31 4.00 3.73 3.50 3.29 3.11 2.95 2.80 2.67 2.55 2.43 2.33 2.24 2.15
57 6.33 5.70 5.18 4.75 4.38 4.07 3.80 3.56 3.35 3.17 3.00 2.85 2.71 2.59 2.48 2.38 2.28 2.19
58 6.44 5.80 5.27 4.83 4.46 4.14 3.87 3.63 3.41 3.22 3.05 2.90 2.76 2.64 2.52 2.42 2.32 2.23
59 6.56 5.90 5.36 4.92 4.54 4.21 3.93 3.69 3.47 3.28 3.11 2.95 2.81 2.68 2.57 2.46 2.36 2.27
60 6.67 6.00 5.45 5.00 4.61 4.28 4.00 3.75 3.53 3.34 3.16 3.00 2.86 2.72 2.61 2.50 2.40 2.30
68 7.55 6.80 6.18 5.66 5.23 4.86 4.54 4.25 4.00 3.78 3.58 3.40 3.24 3.09 2.96 2.84 2.72 2.61
70 7.78 7.00 6.36 5.83 5.38 5.00 4.67 4.38 4.12 3.89 3.68 3.50 3.33 3.18 3.05 2.92 2.80 2.69
72 8.00 7.20 6.54 6.00 5.54 5.14 4.80 4.50 4.24 4.00 3.79 3.60 3.43 3.27 3.13 3.00 2.88 2.77
76 6.91 6.33 5.84 5.43 5.07 4.75 4.47 4.23 4.00 3.80 3.62 3.45 3.31 3.17 3.04 2.92
80 7.27 6.66 6.15 5.71 5.34 5.00 4.70 4.45 4.21 4.00 3.81 3.63 3.48 3.34 3.20 3.07
84 7.00 6.46 6.00 5.60 5.25 4.94 4.67 4.42 4.20 4.00 3.81 3.65 3.50 3.36 3.23
95 7.31 6.78 6.33 5.94 5.59 5.28 5.00 4.75 4.52 4.32 4.13 3.96 3.80 3.65
96 7.38 6.85 6.40 6.00 5.64 5.34 5.05 4.80 4.57 4.36 4.18 4.00 3.84 3.69
102 7.28 6.80 6.38 6.00 5.67 5.37 5.10 4.86 4.63 4.44 4.25 4.08 3.92
112 7.00 6.59 6.23 5.89 5.60 5.33 5.08 4.87 4.67 4.48 4.30
Martin stock sprockets in pitches No. 40 through No. 100 are available with 8 to 60 teeth inclusive and in all common larger sizes for all pitches.
E-170
 Sprocket No. 25
Diameter ¼" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
6 0.500 0.583 0.370 71 5.652 5.796 5.521 136 10.823 10.970 10.693
7 0.576 0.669 0.432 72 5.732 5.876 5.602 137 10.903 11.050 10.772
8 0.653 0.754 0.523 73 5.811 5.956 5.680 138 10.983 11.130 10.853
9 0.731 0.837 0.591 74 5.891 6.035 5.761 139 11.062 11.209 10.932
10 0.809 0.919 0.679 75 5.970 6.115 5.839 140 11.142 11.289 11.012
11 0.887 1.002 0.748 76 6.050 6.195 5.920 141 11.221 11.369 11.091
12 0.966 1.083 0.836 77 6.129 6.274 5.998 142 11.301 11.448 11.171
13 1.045 1.167 0.907 78 6.209 6.354 6.079 143 11.380 11.528 11.250
14 1.124 1.246 0.994 79 6.288 6.433 6.157 144 11.460 11.607 11.330
15 1.203 1.326 1.066 80 6.368 6.513 6.238 145 11.540 11.687 11.409
16 1.282 1.407 1.152 81 6.448 6.593 6.317 146 11.619 11.767 11.489
17 1.361 1.487 1.225 82 6.527 6.672 6.397 147 11.699 11.846 11.568
18 1.440 1.568 1.310 83 6.607 6.752 6.476 148 11.779 11.926 11.649
19 1.519 1.648 1.383 84 6.686 6.832 6.556 149 11.858 12.005 11.727
20 1.598 1.729 1.468 85 6.766 6.911 6.635 150 11.938 12.084 11.807
21 1.678 1.809 1.543 86 6.845 6.991 6.715 151 12.017 12.164 11.886
22 1.757 1.889 1.627 87 6.925 7.070 6.794 152 12.097 12.244 11.966
23 1.836 1.969 1.702 88 7.004 7.150 6.874 153 12.176 12.323 12.045
24 1.915 2.049 1.785 89 7.084 7.230 6.953 154 12.256 12.403 12.125
25 1.995 2.129 1.861 90 7.164 7.309 7.034 155 12.335 12.482 12.204
26 2.074 2.209 1.944 91 7.243 7.389 7.112 156 12.415 12.562 12.284
27 2.154 2.289 2.020 92 7.323 7.468 7.193 157 12.494 12.641 12.363
28 2.233 2.369 2.103 93 7.402 7.548 7.271 158 12.574 12.721 12.444
29 2.312 2.449 2.179 94 7.482 7.628 7.352 159 12.654 12.801 12.523
30 2.392 2.529 2.262 95 7.561 7.707 7.430 160 12.733 12.881 12.603
31 2.471 2.609 2.338 96 7.641 7.787 7.511 161 12.813 12.960 12.682
32 2.551 2.688 2.421 97 7.720 7.866 7.589 162 12.893 13.039 12.762
33 2.630 2.768 2.497 98 7.800 7.946 7.670 163 12.972 13.119 12.841
34 2.710 2.848 2.580 99 7.880 8.026 7.749 164 13.051 13.199 12.921
35 2.789 2.928 2.656 100 7.959 8.105 7.829 165 13.131 13.278 13.000
36 2.869 3.008 2.739 101 8.039 8.185 7.908 166 13.211 13.357 13.080
37 2.948 3.087 2.815 102 8.118 8.264 7.988 167 13.290 13.437 13.159
38 3.028 3.167 2.898 103 8.198 8.344 8.067 168 13.370 13.517 13.239
39 3.107 3.247 2.975 104 8.277 8.424 8.147 169 13.450 13.597 13.318
40 3.187 3.327 3.057 105 8.357 8.503 8.226 170 13.529 13.676 13.398
41 3.266 3.406 3.134 106 8.437 8.583 8.307 171 13.608 13.756 13.477
42 3.346 3.486 3.216 107 8.516 8.662 8.385 172 13.688 13.835 13.558
43 3.425 3.566 3.293 108 8.596 8.742 8.466 173 13.768 13.915 13.637
44 3.505 3.646 3.375 109 8.675 8.822 8.544 174 13.847 13.995 13.717
45 3.584 3.725 3.452 110 8.755 8.901 8.625 175 13.927 14.074 13.796
46 3.664 3.805 3.534 111 8.834 8.981 8.703 176 14.006 14.154 13.876
47 3.743 3.885 3.611 112 8.914 9.060 8.784 177 14.086 14.233 13.955
48 3.823 3.964 3.693 113 8.994 9.140 8.863 178 14.166 14.313 14.035
49 3.902 4.044 3.770 114 9.073 9.220 8.943 179 14.245 14.392 14.114
50 3.982 4.124 3.852 115 9.153 9.299 9.022 180 14.325 14.472 14.195
51 4.061 4.203 3.929 116 9.232 9.379 9.102 181 14.404 14.551 14.273
52 4.141 4.283 4.011 117 9.312 9.458 9.181 182 14.484 14.631 14.353
53 4.220 4.363 4.088 118 9.391 9.538 9.261 183 14.564 14.711 14.433
54 4.300 4.442 4.170 119 9.471 9.618 9.340 184 14.643 14.790 14.513
55 4.379 4.522 4.247 120 9.550 9.697 9.420 185 14.722 14.870 14.591
56 4.459 4.602 4.329 121 9.630 9.777 9.499 186 14.803 14.949 14.672
57 4.538 4.681 4.407 122 9.709 9.856 9.579 187 14.882 15.029 14.751
58 4.618 4.761 4.488 123 9.789 9.936 9.658 188 14.961 15.109 14.831
59 4.697 4.841 4.566 124 9.869 10.016 9.739 189 15.041 15.188 14.910
60 4.777 4.920 4.647 125 9.949 10.095 9.818 190 15.120 15.268 14.990
61 4.857 5.000 4.725 126 10.028 10.175 9.898 191 15.200 15.347 15.069
62 4.936 5.080 4.806 127 10.108 10.255 9.977 192 15.279 15.427 15.149
63 5.016 5.159 4.884 128 10.187 10.334 10.057 193 15.359 15.507 15.228
64 5.095 5.239 4.965 129 10.267 10.414 10.136 194 15.439 15.586 15.308
65 5.175 5.319 5.044 130 10.346 10.493 10.216 195 15.518 15.666 15.387
66 5.254 5.398 5.124 131 10.426 10.573 10.295 196 15.598 15.745 15.467
67 5.334 5.478 5.203 132 10.505 10.652 10.375 197 15.678 15.824 15.547
68 5.413 5.558 5.283 133 10.585 10.732 10.454 198 15.757 15.904 15.626
69 5.493 5.637 5.362 134 10.664 10.811 10.534 199 15.837 15.984 15.706
70 5.572 5.717 5.442 135 10.744 10.891 10.613 200 15.916 16.064 15.786
Odd tooth “bottom diameters” equal pitch diameters minus .130".

E-171
 No. 35 Sprocket
3/8" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 0.638 0.741 0.407 71 8.478 8.694 8.276 136 16.235 16.456 16.035
6 0.750 0.875 0.550 72 8.597 8.814 8.397 137 16.355 16.575 16.154
7 0.864 1.004 0.643 73 8.717 8.933 8.514 138 16.474 16.695 16.274
8 9.80 1.130 0.780 74 8.836 9.053 8.636 139 16.593 16.814 16.392
9 1.097 1.256 0.880 75 8.955 9.172 8.753 140 16.713 16.934 16.513
10 1.214 1.379 1.014 76 9.074 9.292 8.874 141 16.832 17.053 16.631
11 1.331 1.502 1.117 77 9.194 9.411 8.992 142 16.952 17.172 16.752
12 1.449 1.625 1.249 78 9.313 9.531 9.113 143 17.071 17.292 16.870
13 1.567 1.746 1.356 79 9.432 9.650 9.231 144 17.190 17.411 16.990
14 1.685 1.868 1.485 80 9.552 9.770 9.352 145 17.309 17.531 17.108
15 1.804 1.989 1.594 81 9.671 9.889 9.469 146 17.429 17.650 17.229
16 1.922 2.110 1.722 82 9.791 10.008 9.591 147 17.548 17.769 17.347
17 2.041 2.231 1.832 83 9.910 10.128 9.708 148 17.667 17.889 17.467
18 2.160 2.352 1.960 84 10.029 10.247 9.829 149 17.787 18.008 17.586
19 2.279 2.472 2.071 85 10.148 10.367 9.947 150 17.906 18.128 17.706
20 2.397 2.593 2.197 86 10.268 10.486 10.068 151 18.026 18.247 17.825
21 2.516 2.713 2.309 87 10.387 10.605 10.285 152 18.145 18.366 17.945
22 2.635 2.833 2.435 88 10.506 10.725 10.306 153 18.264 18.486 18.063
23 2.754 2.954 2.548 89 10.626 10.844 10.424 154 18.384 18.605 18.184
24 2.873 3.074 2.673 90 10.745 10.964 10.545 155 18.503 18.724 18.302
25 2.992 3.194 2.786 91 10.865 11.083 10.663 156 18.623 18.844 18.423
26 3.111 3.314 2.911 92 10.934 11.202 10.784 157 18.742 18.963 18.541
27 3.230 3.434 3.025 93 11.103 11.322 10.902 158 18.861 19.082 18.661
28 3.349 3.553 3.149 94 11.223 11.441 11.023 159 18.981 19.202 18.780
29 3.468 3.673 3.263 95 11.342 11.561 11.140 160 19.100 19.321 18.900
30 3.588 3.793 3.388 96 11.461 11.680 11.261 161 19.219 19.440 19.018
31 3.707 3.913 3.502 97 11.581 11.799 11.379 162 19.338 19.560 19.138
32 3.826 4.032 3.626 98 11.700 11.919 11.500 163 19.458 19.679 19.257
33 3.945 4.152 3.741 99 11.819 12.038 11.618 164 19.577 19.799 19.377
34 4.064 4.272 3.864 100 11.939 12.158 11.739 165 19.697 19.918 19.496
35 4.184 4.392 3.979 101 12.058 12.277 11.856 166 19.816 20.037 19.616
36 4.303 4.511 4.103 102 12.177 12.396 11.977 167 19.935 20.090 19.734
37 4.422 4.631 4.218 103 12.297 12.516 12.095 168 20.055 20.276 19.855
38 4.541 4.751 4.341 104 12.416 12.635 12.216 169 20.174 20.396 19.973
39 4.661 4.870 4.457 105 12.536 12.755 12.334 170 20.294 20.515 20.094
40 4.780 4.990 4.580 106 12.655 12.874 12.455 171 20.413 20.634 20.212
41 4.899 5.109 4.695 107 12.774 12.993 12.573 172 20.532 20.754 20.332
42 5.018 5.229 4.818 108 12.893 13.113 12.693 173 20.652 20.873 20.451
43 5.138 5.349 4.934 109 13.013 13.232 12.811 174 20.771 20.993 20.571
44 5.257 5.468 5.057 110 13.132 13.352 12.932 175 20.890 21.112 20.689
45 5.376 5.588 5.173 111 13.251 13.471 13.050 176 21.010 21.231 20.810
46 5.495 5.707 5.295 112 13.371 13.590 13.171 177 21.129 21.351 20.928
47 5.615 5.827 5.411 113 13.490 13.710 13.289 178 21.248 21.470 21.048
48 5.734 5.946 5.534 114 13.610 13.829 13.410 179 21.368 21.589 21.167
49 5.853 6.066 5.650 115 13.729 13.949 13.528 180 21.487 21.709 21.287
50 5.972 6.186 5.772 116 13.848 14.068 13.648 181 21.606 21.828 21.406
51 6.092 6.305 5.889 117 13.968 14.187 13.766 182 21.726 21.948 21.526
52 6.211 6.425 6.011 118 14.087 14.307 13.887 183 21.845 22.067 21.644
53 6.330 6.544 6.127 119 14.206 14.426 14.005 184 21.965 22.186 21.765
54 6.449 6.663 6.249 120 14.326 14.546 14.126 185 22.084 22.306 21.883
55 6.569 6.783 6.366 121 14.445 14.665 14.244 186 22.203 22.425 22.003
56 6.688 6.903 6.488 122 14.564 14.784 14.364 187 22.323 22.544 22.122
57 6.807 7.022 6.605 123 14.684 14.904 14.482 188 22.442 22.664 22.242
58 6.927 7.142 6.727 124 14.803 15.023 14.603 189 22.561 22.783 22.360
59 7.046 7.261 6.843 125 14.922 15.143 14.721 190 22.681 22.902 22.481
60 7.165 7.380 6.965 126 15.042 15.262 14.842 191 22.800 23.022 22.599
61 7.285 7.500 7.082 127 15.161 15.381 14.960 192 22.919 23.141 22.719
62 7.404 7.619 7.204 128 15.281 15.501 15.081 193 23.039 23.261 22.838
63 7.523 7.739 7.321 129 15.400 15.620 15.199 194 23.158 23.380 22.958
64 7.643 7.859 7.443 130 15.519 15.740 15.319 195 23.277 23.499 23.177
65 7.762 7.978 7.560 131 15.639 15.859 15.437 196 23.397 23.619 23.197
66 7.881 8.097 7.681 132 15.758 15.978 15.558 197 23.516 23.738 23.315
67 8.001 8.217 7.798 133 15.877 16.098 15.676 198 23.636 23.858 23.436
68 8.120 8.336 7.920 134 15.996 16.217 15.796 199 23.755 23.977 23.554
69 8.239 8.456 8.037 135 16.116 16.337 15.915 200 23.874 24.096 23.674
70 8.358 8.575 8.158

E-172
 Sprocket No. 40
Diameter ½" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 0.851 0.988 0.497 71 11.304 11.592 10.988 136 21.647 21.941 21.334
6 1.000 1.166 0.688 72 11.463 11.752 11.151 137 21.806 22.100 21.492
7 1.152 1.338 0.812 73 11.622 11.911 11.306 138 21.965 22.259 21.653
8 1.307 1.507 0.995 74 11.781 12.070 11.468 139 22.124 22.419 21.810
9 1.462 1.674 1.127 75 11.940 12.229 11.625 140 22.284 22.578 21.971
10 1.618 1.839 1.305 76 12.099 12.389 11.786 141 22.442 22.737 22.129
11 1.775 2.003 1.444 77 12.258 12.548 11.943 142 22.602 22.896 22.289
12 1.932 2.166 1.614 78 12.417 12.707 12.105 143 22.761 23.055 22.447
13 2.089 2.328 1.761 79 12.576 12.866 12.261 144 22.920 23.214 22.607
14 2.247 2.490 1.934 80 12.736 13.026 12.423 145 23.079 23.374 22.765
15 2.405 2.652 2.079 81 12.895 13.185 12.580 146 23.238 23.533 22.926
16 2.563 2.814 2.250 82 13.054 13.344 12.742 147 23.398 23.692 23.088
17 2.721 2.974 2.397 83 13.213 13.503 12.898 148 23.557 23.851 23.244
18 2.879 3.136 2.567 84 13.372 13.663 13.059 149 23.716 24.010 23.402
19 3.038 3.292 2.715 85 13.531 13.822 13.216 150 23.875 24.170 23.562
20 3.196 3.457 2.883 86 13.690 13.981 13.373 151 24.034 24.329 23.720
21 3.355 3.618 3.033 87 13.849 14.140 13.534 152 24.193 24.488 23.880
22 3.513 3.778 3.201 88 14.009 14.299 13.696 153 24.352 24.647 24.038
23 3.672 3.938 3.351 89 14.168 14.459 13.853 154 24.512 24.806 24.199
24 3.831 4.098 3.518 90 14.327 14.618 14.014 155 24.672 24.965 24.357
25 3.989 4.258 3.669 91 14.486 14.777 14.171 156 24.830 25.124 24.517
26 4.148 4.418 3.835 92 14.645 14.936 14.332 157 24.989 25.284 24.675
27 4.307 4.578 3.987 93 14.804 15.096 14.489 158 24.148 25.443 24.835
28 4.465 4.738 4.153 94 14.963 15.255 14.651 159 25.307 25.602 24.993
29 4.625 4.898 4.305 95 15.122 15.414 14.808 160 25.466 25.761 25.154
30 4.783 5.057 4.471 96 15.282 15.573 14.969 161 25.625 25.920 25.312
31 4.942 5.217 4.623 97 15.441 15.732 15.126 162 25.785 26.080 25.472
32 5.101 5.376 4.788 98 15.600 15.892 15.287 163 25.944 26.239 25.630
33 5.260 5.536 4.941 99 15.759 16.051 15.445 164 26.103 26.398 25.790
34 5.419 5.696 5.107 100 15.918 16.210 15.605 165 26.262 26.557 25.948
35 5.578 5.856 5.260 101 16.077 16.369 15.763 166 26.421 26.716 26.109
36 5.737 6.015 5.425 102 16.236 16.528 15.924 167 26.581 26.876 26.266
37 5.896 6.174 5.578 103 16.395 16.688 16.081 168 25.739 27.035 26.427
38 6.055 6.334 5.742 104 16.555 16.847 16.242 169 26.899 27.194 26.585
39 6.214 6.494 5.896 105 16.714 17.006 16.399 170 27.058 27.353 26.745
40 6.373 6.653 6.061 106 16.873 17.165 16.561 171 27.217 27.512 26.903
41 6.532 6.812 6.214 107 17.032 17.324 16.717 172 27.376 27.671 27.063
42 6.691 6.972 6.379 108 17.191 17.484 16.878 173 27.535 27.831 27.221
43 6.850 7.132 6.532 109 17.351 17.643 17.036 174 27.694 27.990 27.382
44 7.009 7.291 6.696 110 17.509 17.802 17.197 175 27.854 28.149 27.540
45 7.168 7.450 6.851 111 17.668 17.962 17.304 176 28.013 28.308 27.700
46 7.327 7.609 7.014 112 17.827 18.121 17.515 177 28.172 28.467 27.858
47 7.486 7.769 7.169 113 17.987 18.280 17.672 178 28.331 28.626 28.018
48 7.645 7.928 7.332 114 18.146 18.439 17.834 179 28.490 28.786 28.176
49 7.804 8.088 7.487 115 18.305 18.598 17.991 180 28.649 28.945 28.337
50 7.963 8.248 7.650 116 18.464 18.757 18.151 181 28.808 29.104 28.495
51 8.122 8.406 7.805 117 18.623 18.916 18.309 182 28.968 28.263 28.655
52 8.281 8.566 7.968 118 18.782 19.076 18.470 183 29.127 29.422 28.813
53 8.440 8.725 8.124 119 18.941 19.235 18.627 184 29.286 29.581 28.973
54 8.599 8.884 8.286 120 19.101 19.394 18.788 185 29.445 29.741 29.131
55 8.758 9.044 8.442 121 19.260 19.553 18.946 186 29.604 29.900 29.291
56 8.917 9.204 8.605 122 19.419 19.712 19.106 187 29.763 30.059 29.450
57 9.077 9.362 8.760 123 19.578 19.872 19.264 188 29.922 30.218 29.610
58 9.235 9.522 8.924 124 19.737 20.031 19.425 189 30.082 30.387 29.768
59 9.395 9.628 9.078 125 19.896 20.190 19.582 190 30.241 30.536 29.928
60 9.554 9.840 9.241 126 20.056 20.349 19.743 191 30.400 30.696 30.086
61 9.713 10.000 9.397 127 20.215 20.508 19.900 192 30.559 30.855 30.246
62 9.872 10.159 9.559 128 20.374 20.667 20.061 193 30.718 31.014 30.404
63 10.031 10.319 9.715 129 20.533 20.827 20.219 194 30.877 31.173 30.565
64 10.190 10.478 9.872 130 20.692 20.986 20.379 195 31.037 31.332 30.723
65 10.349 10.673 10.033 131 20.851 21.145 20.537 196 31.196 31.491 30.878
66 10.508 10.796 10.195 132 21.010 21.304 20.698 197 31.355 31.651 31.042
67 10.667 10.955 10.352 133 21.169 21.463 20.855 198 31.514 31.810 31.202
68 10.826 11.115 10.514 134 21.329 21.623 21.016 199 31.673 31.969 31.359
69 10.985 11.274 10.670 135 21.488 21.782 21.174 200 31.832 32.128 31.520
70 11.145 11.433 10.832

E-173
 No. 50 Sprocket
5/8" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 1.063 1.235 0.611 71 14.129 14.491 13.726 136 27.059 27.426 26.659
6 1.250 1.458 0.850 72 14.329 14.690 13.929 137 27.258 27.626 26.856
7 1.441 1.673 1.104 73 14.528 14.889 14.124 138 27.457 27.824 27.057
8 1.633 1.884 1.233 74 14.726 15.088 14.326 139 27.656 28.024 27.254
9 1.828 2.093 1.400 75 14.925 15.287 14.522 140 27.854 28.223 27.454
10 2.023 2.299 1.623 76 15.124 15.486 14.724 141 28.053 28.421 27.652
11 2.219 2.504 1.796 77 15.323 15.685 14.920 142 28.253 28.621 27.853
12 2.415 2.708 2.015 78 15.522 15.884 15.122 143 28.451 28.819 28.050
13 2.612 2.911 2.193 79 15.721 16.083 15.318 144 28.650 29.018 28.250
14 2.809 3.113 2.409 80 15.919 16.283 15.519 145 28.849 28.218 28.447
15 3.006 3.315 2.590 81 16.119 16.481 15.715 146 29.048 29.416 28.608
16 3.204 3.517 2.804 82 16.318 16.681 15.918 147 29.247 29.615 28.845
17 3.401 3.718 2.987 83 16.516 16.879 16.113 148 29.446 29.814 29.046
18 3.599 3.919 3.159 84 16.715 17.079 16.315 149 29.645 30.013 29.243
19 3.798 4.121 3.384 85 16.914 17.278 16.511 150 29.844 30.213 29.444
20 3.995 4.321 3.595 86 17.113 17.476 16.713 151 30.043 30.411 29.641
21 4.194 4.522 3.782 87 17.312 17.676 16.909 152 30.241 30.610 29.841
22 4.392 4.722 3.992 88 17.511 17.874 17.111 153 30.441 30.809 30.039
23 4.590 4.923 4.179 89 17.709 18.074 17.307 154 30.639 31.008 30.239
24 4.788 5.123 4.388 90 17.909 18.273 17.509 155 30.838 31.207 30.437
25 4.987 5.323 4.577 91 18.108 18.472 17.705 156 31.038 31.406 30.638
26 5.185 5.523 4.785 92 18.306 18.671 17.906 157 31.236 31.605 30.835
27 5.384 5.723 4.975 93 18.505 18.870 18.103 158 31.435 31.804 31.035
28 5.582 5.922 5.182 94 18.704 19.069 18.304 159 31.634 32.003 31.233
29 5.781 6.122 5.371 95 18.903 19.268 18.501 160 31.833 32.202 31.433
30 5.979 6.321 5.579 96 19.102 19.467 18.702 161 32.032 32.401 31.630
31 6.178 6.521 5.770 97 19.301 19.666 18.898 162 32.231 32.600 31.831
32 6.376 6.721 5.976 98 19.500 19.865 19.100 163 32.430 32.799 32.082
33 6.575 6.921 6.168 99 19.699 20.064 19.296 164 32.629 32.998 32.229
34 6.774 7.120 6.374 100 19.898 20.263 19.498 165 32.828 33.197 32.426
35 6.973 7.319 6.565 101 20.096 20.462 19.694 166 33.027 33.396 32.627
36 7.171 7.519 6.771 102 20.296 20.661 19.896 167 33.226 33.595 32.824
37 7.370 7.718 6.963 103 20.494 20.860 20.092 168 33.424 33.794 33.024
38 7.569 7.918 7.169 104 20.693 21.059 20.293 169 33.624 33.993 33.222
39 7.768 8.117 7.361 105 20.893 21.258 20.490 170 33.823 34.192 33.423
40 7.966 8.316 7.566 106 21.091 21.457 20.691 171 34.021 34.391 33.620
41 8.165 8.516 7.759 107 21.290 21.656 20.888 172 34.220 34.589 33.820
42 8.364 8.715 7.964 108 21.489 21.855 21.089 173 34.419 34.789 34.018
43 8.563 8.914 8.157 109 21.688 22.054 21.286 174 36.618 34.988 34.218
44 8.761 9.114 8.361 110 21.887 22.253 21.487 175 34.817 35.186 34.416
45 8.960 9.313 8.554 111 22.086 22.452 21.684 176 35.016 35.386 34.616
46 9.159 9.512 8.759 112 22.284 22.651 21.884 177 35.215 35.584 34.814
47 9.358 9.711 8.952 113 22.484 22.850 22.081 178 35.414 35.783 35.014
48 9.556 9.911 9.156 114 22.683 23.049 22.283 179 35.613 35.983 35.211
49 9.755 10.110 9.350 115 22.881 23.248 22.479 180 35.812 36.181 35.412
50 9.954 10.309 9.554 116 23.080 23.447 22.680 181 36.011 36.380 35.609
51 10.153 10.508 9.748 117 23.279 23.646 22.827 182 36.209 36.579 35.809
52 10.351 10.708 9.951 118 23.478 23.845 23.078 183 36.409 36.778 36.007
53 10.550 10.907 10.146 119 23.677 24.004 23.275 184 36.608 36.977 36.208
54 10.749 11.106 10.349 120 23.876 24.243 23.476 185 36.806 37.176 36.405
55 10.948 11.305 10.543 121 24.075 24.442 23.673 186 37.005 37.375 36.605
56 11.147 11.504 10.747 122 24.274 24.641 23.874 187 37.204 37.574 36.803
57 11.346 11.703 10.941 123 24.473 24.840 24.071 188 37.403 37.773 37.003
58 11.544 11.903 11.144 124 24.672 25.039 24.272 189 37.602 39.972 37.201
59 11.743 12.102 11.339 125 24.871 25.238 24.469 190 37.801 38.171 37.401
60 11.942 12.301 11.542 126 25.069 25.437 24.669 191 38.000 38.370 37.599
61 12.141 12.500 11.737 127 25.269 25.636 24.867 192 38.199 38.569 37.799
62 12.340 12.699 11.940 128 25.468 25.834 25.068 193 38.398 38.768 37.998
63 12.539 12.898 12.135 129 25.666 26.034 25.264 194 38.597 38.967 38.197
64 12.738 13.098 12.338 130 25.865 26.233 25.465 195 38.796 39.166 38.394
65 12.936 13.296 12.533 131 26.064 26.432 25.662 196 38.994 39.364 38.594
66 13.135 13.496 12.735 132 26.263 26.631 25.863 197 39.194 39.564 38.792
67 13.334 13.694 12.930 133 26.462 26.829 26.060 198 39.393 39.763 38.993
68 13.533 13.894 13.133 134 26.661 27.029 26.261 199 39.591 39.961 39.190
69 13.732 14.093 13.328 135 26.860 27.228 26.458 200 39.791 40.161 39.391
70 13.931 14.292 13.531

E-174
 Sprocket No. 60
Diameter ¾" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 1.276 1.482 0.745 71 16.955 17.389 16.482 136 32.471 32.912 32.002
6 1.500 1.749 1.031 72 17.195 17.628 16.726 137 32.709 33.151 32.238
7 1.729 2.007 1.216 73 17.433 17.867 16.960 138 32.948 33.389 32.479
8 1.960 2.261 1.491 74 17.672 18.106 17.203 139 33.187 33.629 32.716
9 2.193 2.511 1.691 75 17.910 18.344 17.437 140 33.425 33.867 32.956
10 2.427 2.759 1.958 76 18.149 18.584 17.680 141 33.664 34.106 33.193
11 2.663 3.005 2.166 77 18.388 18.822 17.915 142 33.903 34.345 33.434
12 2.898 3.249 2.429 78 18.626 19.061 18.157 143 34.142 34.583 33.670
13 3.134 3.493 2.642 79 18.865 19.300 18.392 144 34.380 34.822 33.911
14 3.371 3.736 2.902 80 19.103 19.539 18.634 145 34.619 35.061 34.148
15 3.608 3.978 3.119 81 19.343 19.778 18.870 146 34.858 35.300 34.389
16 3.845 4.220 3.380 82 19.581 20.017 19.112 147 35.096 35.538 34.625
17 4.082 4.462 3.595 83 19.820 20.255 19.347 148 35.335 35.777 34.866
18 4.319 4.703 3.850 84 20.058 20.495 19.589 149 35.574 36.016 35.103
19 4.557 4.945 4.072 85 20.297 20.733 19.824 150 35.813 36.255 35.344
20 4.794 5.186 4.325 86 20.536 20.972 20.067 151 36.051 36.494 35.580
21 5.033 5.426 4.549 87 20.774 21.211 20.302 152 36.390 36.732 35.821
22 5.270 5.666 4.801 88 21.013 21.449 20.544 153 36.529 36.971 36.058
23 5.508 5.907 5.026 89 21.251 21.689 20.779 154 36.767 37.210 36.298
24 5.746 6.147 5.277 90 21.491 21.927 21.022 155 37.006 37.448 36.535
25 5.984 6.387 5.503 91 21.729 22.166 21.257 156 37.245 37.688 36.776
26 6.222 6.627 5.753 92 21.968 22.405 21.499 157 37.484 37.926 37.013
27 6.461 6.867 5.980 93 22.206 22.644 21.734 158 37.722 38.165 37.253
28 6.698 7.106 6.229 94 22.445 22.883 21.976 159 37.961 38.404 37.490
29 6.937 7.346 6.458 95 22.684 23.121 22.212 160 38.200 38.642 37.731
30 7.175 7.586 6.706 96 22.922 23.360 22.453 161 38.438 38.881 37.968
31 7.413 7.826 6.935 97 23.162 23.599 22.689 162 38.677 39.120 38.208
32 7.652 8.065 7.183 98 23.400 23.838 22.931 163 38.916 39.359 38.445
33 7.890 8.305 7.412 99 23.639 24.077 23.167 164 39.155 39.597 38.686
34 8.129 8.544 7.660 100 23.877 24.316 23.408 165 39.393 39.836 38.922
35 8.367 8.783 7.889 101 24.116 24.554 23.644 166 39.632 40.075 39.163
36 8.606 9.023 8.137 102 24.355 24.793 23.886 167 39.871 40.314 39.400
37 8.844 9.262 8.367 103 24.593 25.032 24.121 168 40.109 40.553 39.640
38 9.083 9.501 8.614 104 24.832 25.271 24.363 169 40.349 40.791 39.877
39 9.321 9.740 8.844 105 25.071 25.510 24.599 170 40.587 41.030 40.118
40 9.560 9.980 9.091 106 25.310 25.748 24.841 171 40.826 41.269 40.355
41 9.798 10.219 9.321 107 25.548 25.987 25.076 172 41.064 41.507 40.595
42 10.037 10.458 9.568 108 25.787 26.226 25.318 173 41.303 41.747 40.832
43 10.275 10.697 9.799 109 26.026 26.465 25.554 174 41.542 41.985 41.073
44 10.514 10.937 10.045 110 26.264 26.704 25.795 175 41.780 42.224 41.310
45 10.752 11.176 10.276 111 26.503 26.942 26.031 176 42.020 42.463 41.551
46 10.991 11.414 10.522 112 26.741 27.181 26.272 177 42.258 42.701 41.787
47 11.229 11.654 10.754 113 26.981 27.420 26.507 178 42.497 42.940 42.028
48 11.468 11.893 10.999 114 27.219 27.659 26.750 179 42.735 43.179 42.265
49 11.706 12.132 11.231 115 27.458 27.898 26.986 180 42.974 43.418 42.505
50 11.945 12.371 11.476 116 27.696 28.136 27.227 181 43.213 43.656 42.742
51 12.183 12.610 11.708 117 27.935 28.375 27.464 182 43.451 43.895 42.982
52 12.422 12.849 11.953 118 28.174 28.614 27.705 183 43.691 44.134 43.220
53 12.660 13.088 12.186 119 28.412 28.853 27.941 184 43.929 44.372 43.460
54 12.899 13.327 12.430 120 28.652 29.091 28.183 185 44.168 44.612 43.697
55 13.137 13.566 12.663 121 28.890 29.330 28.418 186 44.406 44.850 43.937
56 13.376 13.805 12.907 122 29.129 29.569 28.660 187 44.645 45.089 44.174
57 13.615 14.044 13.140 123 29.367 29.808 28.896 188 44.884 45.328 44.415
58 13.853 14.283 13.384 124 29.606 30.047 29.137 189 45.122 45.566 44.652
59 14.092 14.522 13.618 125 29.845 30.285 29.373 190 45.362 45.805 44.893
60 14.330 14.761 13.861 126 30.083 30.524 29.614 191 45.600 46.044 45.129
61 14.570 15.000 14.095 127 30.323 30.763 29.851 192 45.839 46.283 45.370
62 14.808 15.239 14.339 128 30.561 31.001 30.092 193 46.077 46.521 45.607
63 15.047 15.478 14.573 129 30.800 31.241 30.328 194 46.316 46.760 45.847
64 15.285 15.717 14.816 130 31.038 31.479 30.569 195 46.555 46.999 46.084
65 15.524 15.956 15.050 131 31.277 31.718 30.806 196 46.793 47.237 46.324
66 15.762 16.195 15.293 132 31.516 31.957 31.047 197 47.033 47.477 46.562
67 16.001 16.433 15.528 133 31.754 32.195 31.283 198 47.271 47.715 46.802
68 16.240 16.673 15.771 134 31.993 32.435 31.524 199 47.510 47.954 47.039
69 16.478 16.911 16.005 135 32.232 32.673 31.761 200 47.749 48.193 47.280
70 16.717 17.150 16.248

E-175
 No. 80 Sprocket
1" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 1.701 1.976 0.993 71 22.607 23.185 21.977 136 43.294 43.882 42.669
6 2.000 2.332 1.375 72 22.926 23.504 22.301 137 43.612 44.201 42.984
7 2.305 2.676 1.622 73 23.244 23.822 22.613 138 43.931 44.519 43.306
8 2.613 3.014 1.988 74 23.562 24.141 22.937 139 44.249 44.838 43.621
9 2.924 3.348 2.254 75 23.880 24.459 23.250 140 44.567 45.156 43.942
10 3.236 3.678 2.611 76 24.198 24.778 23.573 141 44.885 45.474 44.258
11 3.550 4.006 2.888 77 24.517 25.096 23.887 142 45.204 45.793 44.579
12 3.864 4.332 3.239 78 24.835 25.415 24.210 143 45.522 46.111 44.894
13 4.179 4.657 3.523 79 25.153 25.733 24.523 144 45.840 46.429 45.215
14 4.494 4.981 3.869 80 25.471 26.052 24.846 145 46.158 46.748 45.531
15 4.810 5.304 4.158 81 25.790 26.370 25.160 146 46.477 47.066 45.852
16 5.126 5.627 4.501 82 26.108 26.689 25.483 147 46.795 47.384 46.167
17 5.442 5.949 4.794 83 26.426 27.007 25.796 148 47.113 47.703 46.488
18 5.759 6.271 5.134 84 26.744 27.326 26.119 149 47.432 48.021 46.804
19 6.076 6.593 5.430 85 27.062 27.644 26.433 150 47.750 48.340 47.125
20 6.392 6.914 5.767 86 27.381 27.962 26.756 151 48.068 48.658 47.441
21 6.710 7.235 6.066 87 27.699 28.281 27.069 152 48.386 48.976 47.761
22 7.027 7.555 6.402 88 28.017 28.599 27.392 153 48.705 49.295 48.077
23 7.344 7.876 6.702 89 28.335 28.918 27.706 154 49.023 49.613 48.398
24 7.661 8.196 7.036 90 28.654 29.236 28.029 155 49.341 49.931 48.714
25 7.979 8.516 7.338 91 28.972 29.555 28.343 156 49.660 50.250 49.035
26 8.296 8.836 7.671 92 29.290 29.873 28.665 157 49.978 50.568 49.351
27 8.614 9.156 7.974 93 29.608 30.192 28.979 158 50.296 50.886 49.671
28 8.931 9.475 8.306 94 29.927 30.510 29.302 159 50.615 51.205 49.987
29 9.249 9.795 8.611 95 30.245 30.828 29.616 160 50.933 51.523 50.308
30 9.567 10.114 8.942 96 30.563 31.147 29.938 161 51.251 51.841 50.624
31 9.884 10.434 9.247 97 30.822 31.465 30.252 162 51.569 52.160 50.944
32 10.202 10.753 9.577 98 31.200 31.784 30.575 163 51.888 52.478 51.260
33 10.520 11.073 9.883 99 31.518 32.102 30.889 164 52.206 52.796 51.581
34 10.838 11.392 10.213 100 31.836 32.421 31.211 165 52.524 53.115 51.897
35 11.156 11.711 10.520 101 32.154 32.739 31.526 166 52.843 53.433 52.218
36 11.471 12.030 10.849 102 32.473 33.057 31.848 167 53.161 53.752 52.533
37 11.792 12.349 11.156 103 32.791 33.376 32.162 168 53.479 54.070 52.854
38 12.110 12.668 11.485 104 33.109 33.694 32.484 169 53.798 54.388 53.170
39 12.428 12.987 11.792 105 33.428 34.013 32.799 170 54.116 54.707 53.491
40 12.746 13.306 12.121 106 33.746 34.331 33.121 171 54.434 55.025 53.807
41 13.064 13.625 12.429 107 34.064 34.649 33.435 172 54.752 55.343 54.127
42 13.382 13.944 12.757 108 34.382 34.968 33.757 173 55.071 55.662 54.443
43 13.700 14.263 13.065 109 34.701 35.286 34.072 174 55.389 55.980 54.764
44 14.018 14.582 13.393 110 35.019 35.605 34.394 175 55.707 56.298 55.080
45 14.336 14.901 13.702 111 35.337 35.923 34.709 176 56.026 56.617 55.401
46 14.654 15.219 14.029 112 35.655 36.241 35.030 177 56.344 56.935 55.717
47 14.972 15.538 14.338 113 35.974 36.560 35.345 178 56.662 57.253 56.037
48 15.290 15.857 14.665 114 36.292 36.878 35.667 179 56.980 57.572 56.353
49 15.608 16.176 14.975 115 36.610 37.197 35.982 180 57.299 57.890 56.674
50 15.926 16.495 15.301 116 36.928 37.515 36.303 181 57.617 58.208 56.990
51 16.244 16.813 15.611 117 37.274 37.833 36.618 182 57.935 58.527 57.310
52 16.562 17.132 15.937 118 37.565 38.152 36.940 183 58.254 58.845 57.626
53 16.880 17.451 16.248 119 37.883 38.470 37.255 184 58.572 59.163 57.947
54 17.198 17.769 16.573 120 38.202 38.788 37.577 185 58.890 59.482 58.263
55 17.516 18.088 16.884 121 38.520 39.107 37.892 186 59.208 59.800 58.583
56 17.835 18.407 17.210 122 38.838 39.425 38.213 187 59.527 60.118 58.900
57 18.153 18.725 17.521 123 39.156 39.744 38.528 188 59.845 60.437 59.220
58 18.471 19.044 17.846 124 39.457 40.062 38.850 189 60.163 60.755 59.536
59 18.789 19.363 18.157 125 39.793 40.380 39.165 190 60.482 61.073 59.857
60 19.107 19.681 18.482 126 40.111 40.699 39.486 191 60.800 61.392 60.173
61 19.426 20.000 18.794 127 40.430 41.017 39.801 192 61.118 61.710 60.493
62 19.744 20.318 19.119 128 40.748 41.335 40.123 193 61.436 62.028 60.809
63 20.062 20.637 19.431 129 41.066 41.654 40.438 194 61.755 62.347 61.130
64 20.380 20.956 19.755 130 41.384 41.972 40.759 195 62.073 62.665 61.447
65 20.698 21.274 20.067 131 41.703 42.291 41.075 196 62.391 62.983 61.756
66 21.016 21.593 20.391 132 42.021 42.609 41.396 197 62.710 63.302 62.083
67 21.335 21.911 20.704 133 42.339 42.927 41.711 198 63.028 63.620 62.403
68 21.653 22.230 21.028 134 42.657 43.246 42.032 199 63.346 63.938 62.719
69 21.971 22.548 21.340 135 42.976 43.564 42.348 200 63.665 64.257 63.040
70 22.289 22.867 21.664

E-176
 Sprocket No. 100
Diameter 1¼" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 2.126 2.470 1.273 71 28.259 28.981 27.502 136 54.118 54.853 53.368
6 2.500 2.915 1.750 72 28.658 29.380 27.908 137 54.515 55.251 53.762
7 2.881 3.345 2.059 73 29.055 29.778 28.298 138 54.914 55.649 54.164
8 3.266 3.768 2.516 74 29.453 30.176 28.703 139 55.311 56.048 54.558
9 3.655 4.185 2.849 75 29.850 30.574 29.094 140 55.709 56.445 54.959
10 4.045 4.598 3.295 76 30.248 30.973 29.498 141 56.106 56.843 55.353
11 4.438 5.008 3.639 77 30.646 31.370 29.890 142 56.505 57.241 55.755
12 4.830 5.415 4.080 78 31.044 31.769 30.294 143 56.903 57.639 56.149
13 5.224 5.821 4.435 79 31.441 32.166 30.685 144 57.300 58.036 56.550
14 5.618 6.226 4.868 80 31.839 32.565 31.089 145 57.698 58.435 56.945
15 6.013 6.630 5.229 81 32.238 32.963 31.481 146 58.096 58.833 57.346
16 6.408 7.034 5.658 82 32.635 33.361 31.885 147 58.494 59.230 57.741
17 6.803 7.436 6.024 83 33.033 33.759 32.277 148 58.891 59.629 58.141
18 7.199 7.839 6.449 84 33.430 34.158 32.680 149 59.290 60.026 58.536
19 7.595 8.241 6.819 85 33.828 34.555 33.072 150 59.688 60.425 58.938
20 7.990 8.643 7.240 86 34.226 34.953 33.476 151 60.085 60.823 59.332
21 8.388 9.044 7.613 87 34.624 35.351 33.868 152 60.483 61.220 59.733
22 8.784 9.444 8.034 88 35.022 35.749 34.272 153 60.881 61.619 60.128
23 9.180 9.845 8.409 89 35.419 36.148 34.664 154 61.279 62.016 60.529
24 9.576 10.245 8.827 90 35.818 36.545 35.068 155 61.676 62.414 60.924
25 9.974 10.645 9.204 91 36.215 36.944 35.460 156 62.075 62.813 61.325
26 10.370 11.045 9.620 92 36.613 37.341 35.863 157 62.473 63.210 61.719
27 10.768 11.445 9.999 93 37.010 37.740 36.255 158 62.870 63.608 62.120
28 11.164 11.844 10.414 94 37.409 38.138 36.659 159 63.269 64.006 62.515
29 11.561 12.244 10.794 95 37.806 38.535 37.051 160 63.666 64.404 62.916
30 11.959 12.643 11.209 96 38.204 38.934 37.454 161 64.064 64.801 63.311
31 12.355 13.043 11.590 97 38.603 39.331 37.847 162 64.461 65.200 63.711
32 12.753 13.441 12.003 98 39.000 39.730 38.250 163 64.860 65.598 64.107
33 13.150 13.841 12.385 99 39.398 40.128 38.643 164 65.258 65.995 64.508
34 13.548 14.240 12.798 100 39.795 40.526 39.045 165 65.655 66.394 64.902
35 13.945 14.639 13.181 101 40.193 40.924 39.438 166 66.054 66.791 65.304
36 14.343 15.038 13.593 102 40.591 41.321 39.841 167 66.451 67.190 65.698
37 14.740 15.436 13.976 103 40.989 41.720 40.234 168 66.849 67.588 66.099
38 15.138 15.835 14.388 104 41.386 42.118 40.636 169 67.248 67.985 66.494
39 15.535 16.234 14.772 105 41.785 42.516 41.030 170 67.645 68.384 66.895
40 15.933 16.633 15.183 106 42.183 42.914 41.433 171 68.043 68.781 67.290
41 16.330 17.031 15.567 107 42.580 43.311 41.826 172 68.440 69.179 67.690
42 16.728 17.430 15.978 108 42.978 43.710 42.228 173 68.839 69.578 68.086
43 17.125 17.829 16.363 109 43.376 44.108 42.621 174 69.236 69.975 68.486
44 17.523 18.228 16.773 110 43.774 44.506 43.024 175 69.634 70.373 68.881
45 17.920 18.626 17.159 111 44.171 44.904 43.420 176 70.033 70.771 69.283
46 18.318 19.024 17.568 112 44.569 45.301 43.819 177 70.430 71.169 69.677
47 18.715 19.423 17.954 113 44.968 45.700 44.213 178 70.828 71.566 70.078
48 19.113 19.821 18.363 114 45.365 46.098 44.615 179 71.225 71.965 70.473
49 19.510 20.220 18.750 115 45.763 46.496 45.009 180 71.624 72.363 70.874
50 19.908 20.619 19.158 116 46.160 46.894 45.410 181 72.021 72.760 71.269
51 20.305 21.016 19.546 117 46.559 47.291 45.804 182 72.419 73.159 71.669
52 20.703 21.415 19.953 118 46.956 47.690 46.206 183 72.818 73.556 72.064
53 21.100 21.814 20.341 119 47.354 48.088 46.600 184 73.215 73.954 72.465
54 21.498 22.211 20.748 120 47.753 48.485 47.003 185 73.613 74.353 72.860
55 21.895 22.610 21.137 121 48.150 48.884 47.396 186 74.010 74.750 73.260
56 22.294 23.009 21.544 122 48.548 49.281 47.798 187 74.409 75.148 73.656
57 22.691 23.406 21.932 123 48.945 49.680 48.192 188 74.806 75.546 74.056
58 23.089 23.805 22.339 124 49.344 50.078 48.594 189 75.204 75.944 74.452
59 23.486 24.204 22.728 125 49.741 50.475 48.987 190 75.603 76.341 74.853
60 23.884 24.601 23.134 126 50.139 50.874 49.389 191 76.000 76.740 75.247
61 24.283 25.000 23.524 127 50.538 51.271 49.783 192 76.398 771.38 75.648
62 24.680 25.398 23.930 128 50.935 51.669 50.185 193 76.795 77.535 76.043
63 25.078 25.796 24.320 129 51.333 52.068 50.579 194 77.194 77.934 76.444
64 25.475 26.195 24.725 130 51.730 52.465 50.980 195 77.591 78.331 76.839
65 25.873 26.593 25.115 131 52.129 52.864 51.375 196 77.989 78.729 77.239
66 26.270 26.991 25.520 132 52.526 53.261 51.776 197 78.388 79.128 77.635
67 26.669 27.389 25.911 133 52.924 53.659 52.170 198 78.785 79.525 78.035
68 27.066 27.788 26.316 134 53.321 54.058 52.571 199 79.183 79.923 78.430
69 27.464 28.185 26.707 135 53.720 54.455 52.966 200 79.581 80.321 78.831
70 27.861 28.584 27.111

E-177
 No. 120 Sprocket
1½" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 2.552 2.964 1.552 71 33.911 34.778 33.028 136 64.941 65.823 64.066
6 3.000 3.498 2.125 72 34.389 35.256 33.514 137 65.418 66.302 64.539
7 3.458 4.014 2.496 73 34.866 35.733 33.983 138 65.897 66.779 65.022
8 3.920 4.521 3.045 74 35.343 36.212 34.468 139 66.374 67.257 65.494
9 4.386 5.022 3.444 75 35.820 36.689 34.938 140 66.851 67.734 65.976
10 4.854 5.517 3.979 76 36.297 37.167 35.422 141 67.328 68.211 66.449
11 5.325 6.009 4.392 77 36.776 37.644 35.892 142 67.806 68.690 66.931
12 5.796 6.498 4.921 78 37.253 38.123 36.378 143 68.283 69.167 67.404
13 6.269 6.986 5.347 79 37.730 38.600 36.847 144 68.760 69.644 67.885
14 6.741 7.472 5.866 80 38.207 39.078 37.332 145 69.237 70.122 68.359
15 7.215 7.956 6.300 81 38.685 39.555 37.802 146 69.716 70.599 68.841
16 7.689 8.441 6.814 82 39.162 40.034 38.287 147 70.193 71.076 69.314
17 8.163 8.924 7.254 83 39.639 40.511 38.757 148 70.670 71.555 69.795
18 8.639 9.407 7.764 84 40.116 40.989 39.241 149 71.148 72.032 70.269
19 9.114 9.890 8.207 85 40.593 41.466 39.712 150 71.625 72.510 70.750
20 9.588 10.371 8.713 86 41.072 41.943 40.197 151 72.102 72.987 71.224
21 10.065 10.853 9.161 87 41.549 42.422 40.667 152 72.579 73.464 71.704
22 10.541 11.333 9.666 88 42.026 42.899 41.151 153 73.058 73.943 72.178
23 11.016 11.814 10.115 89 42.503 43.377 41.622 154 73.535 74.420 72.660
24 11.492 12.294 10.617 90 42.981 43.854 42.106 155 74.012 74.897 73.133
25 11.969 12.774 11.070 91 43.458 44.333 42.576 156 74.490 75.375 73.615
26 12.444 13.254 11.569 92 43.935 44.810 43.060 157 74.967 75.852 74.088
27 12.921 13.734 12.024 93 44.412 45.288 43.531 158 75.444 76.329 74.569
28 13.397 14.213 12.522 94 44.891 45.765 44.016 159 75.923 76.808 75.043
29 13.874 14.693 12.978 95 45.368 46.242 44.48 160 76.400 77.285 75.525
30 14.351 15.171 13.476 96 45.845 46.721 44.970 161 76.877 77.762 75.998
31 14.826 15.651 13.933 97 46.323 47.198 45.441 162 77.354 78.240 76.479
32 15.303 16.130 14.428 98 46.800 47.676 45.925 163 77.832 78.717 76.953
33 15.780 16.610 14.887 99 47.277 48.153 46.396 164 78.309 79.194 77.434
34 16.257 17.088 15.382 100 47.754 48.632 46.879 165 78.786 79.673 77.908
35 16.734 17.567 15.842 101 48.231 49.109 47.351 166 79.265 80.150 78.390
36 17.211 18.045 16.336 102 48.710 49.586 47.835 167 79.742 80.628 78.863
37 17.688 18.524 16.797 103 49.187 50.064 48.306 168 80.219 81.105 79.344
38 18.165 19.002 17.290 104 49.664 50.541 48.789 169 80.697 81.582 79.818
39 18.642 19.481 17.751 105 50.142 51.020 49.261 170 81.174 82.061 80.299
40 19.119 19.959 18.244 106 50.619 51.497 49.744 171 81.651 82.538 80.773
41 19.596 20.438 18.706 107 51.096 51.974 50.216 172 82.128 83.015 81.253
42 20.073 20.916 19.198 108 51.573 52.452 50.698 173 82.607 83.493 81.728
43 20.550 21.395 19.661 109 52.052 52.929 51.171 174 83.084 83.970 82.209
44 21.027 21.873 20.152 110 52.529 53.408 51.654 175 83.561 84.447 82.683
45 21.504 22.352 20.615 111 53.006 53.885 52.125 176 84.039 84.926 83.164
46 21.981 22.829 21.106 112 53.483 54.362 52.608 177 84.501 85.403 83.637
47 22.458 23.307 21.570 113 53.961 54.840 53.080 178 84.993 85.880 84.118
48 22.935 23.786 22.060 114 54.438 55.317 53.563 179 85.470 86.358 84.592
49 23.412 24.264 22.525 115 54.915 55.796 54.035 180 85.949 86.835 85.074
50 23.889 24.743 23.014 116 55.392 56.273 54.517 181 86.426 87.312 85.547
51 24.366 25.220 23.480 117 55.871 56.750 54.990 182 86.903 87.791 86.028
52 24.843 25.698 23.968 118 56.348 57.228 55.473 183 87.381 88.268 86.502
53 25.320 26.177 24.434 119 56.825 57.705 55.945 184 87.858 88.745 86.983
54 25.797 26.654 24.922 120 57.303 58.182 56.428 185 88.335 89.223 87.457
55 26.274 27.132 25.389 121 57.780 58.661 56.900 186 88.812 89.700 87.937
56 26.753 27.611 25.878 122 58.257 59.138 57.382 187 89.291 90.177 88.412
57 27.230 28.088 26.344 123 58.734 59.616 57.855 188 89.768 90.656 88.893
58 27.707 28.566 26.832 124 59.213 60.093 58.338 189 90.245 91.133 89.367
59 28.184 29.045 27.299 125 59.690 60.570 58.810 190 90.723 91.610 89.848
60 28.661 29.522 27.786 126 60.167 61.049 59.292 191 91.200 92.088 90.322
61 29.139 30.000 28.254 127 60.645 61.526 59.765 192 91.677 92.565 90.802
62 29.616 30.477 28.741 128 61.122 62.003 60.247 193 92.154 93.042 91.277
63 30.093 30.956 29.208 129 61.599 62.481 60.720 194 92.633 93.521 91.758
64 30.570 31.434 29.695 130 62.076 62.958 61.201 195 93.110 93.998 92.232
65 31.047 31.911 30.163 131 62.555 63.437 61.674 196 93.587 94.475 92.712
66 31.524 32.390 30.649 132 63.032 63.914 62.157 197 94.065 94.953 93.187
67 32.003 32.867 31.118 133 63.509 64.391 62.629 198 94.542 95.430 93.667
68 32.480 33.345 31.605 134 63.986 64.869 63.111 199 95.019 95.907 94.141
69 32.957 33.822 32.073 135 64.464 65.346 63.584 200 95.498 96.386 94.623
70 33.434 34.301 32.559

E-178
 Sprocket No. 140
Diameter 1¾" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 2.977 3.458 1.832 71 39.562 40.574 38.553 136 75.765 76.794 74.765
6 3.500 4.081 2.500 72 40.121 41.132 39.121 137 76.321 77.352 75.316
7 4.034 4.683 2.932 73 40.677 41.689 39.667 138 76.879 77.908 75.879
8 4.573 5.275 3.573 74 41.234 42.247 40.234 139 77.436 78.467 76.431
9 5.117 5.859 4.039 75 41.790 42.803 40.781 140 78.008 79.023 77.008
10 5.663 6.437 4.663 76 42.347 43.362 41.347 141 78.549 79.580 77.545
11 6.213 7.011 5.148 77 42.905 43.918 41.895 142 79.107 80.138 78.107
12 6.762 7.581 5.762 78 43.461 44.476 42.461 143 79.664 80.694 78.484
13 7.313 8.150 6.259 79 44.018 45.033 43.009 144 80.220 81.251 79.220
14 7.865 8.717 6.865 80 44.574 45.591 43.574 145 80.777 81.809 79.773
15 8.418 9.282 7.371 81 45.133 46.148 44.123 146 81.335 82.366 80.335
16 8.971 9.847 7.971 82 45.689 46.706 44.689 147 81.891 82.922 80.887
17 9.524 10.411 8.483 83 46.246 47.262 45.237 148 82.448 83.480 81.448
18 10.078 10.974 9.078 84 46.802 47.821 45.802 149 83.006 84.037 82.000
19 10.633 11.538 9.596 85 47.359 48.377 46.351 150 83.563 84.595 82.563
20 11.186 12.100 10.186 86 47.917 48.934 46.917 151 84.119 85.152 83.115
21 11.743 12.661 10.709 87 48.473 49.492 47.465 152 84.676 85.708 83.676
22 12.297 13.221 11.297 88 49.030 50.048 48.030 153 85.234 86.266 84.229
23 12.852 13.783 11.822 89 49.586 50.607 48.579 154 85.790 86.823 84.790
24 13.407 14.343 12.407 90 50.145 51.163 49.145 155 86.347 87.379 85.343
25 13.963 14.903 12.935 91 50.701 51.721 49.693 156 86.905 87.938 85.905
26 14.518 15.463 13.518 92 51.258 52.278 50.258 157 87.462 88.494 86.457
27 15.075 16.023 14.049 93 51.814 52.836 50.807 158 88.018 89.051 87.018
28 15.629 16.581 14.629 94 52.372 53.393 51.372 159 88.576 89.609 87.571
29 16.186 17.141 15.162 95 52.929 53.949 51.921 160 89.133 90.165 88.133
30 16.742 17.700 15.742 96 53.485 54.507 52.485 161 89.689 90.722 88.685
31 17.297 18.260 16.276 97 54.044 55.064 53.035 162 90.246 91.280 89.246
32 17.854 18.818 16.854 98 54.600 55.622 53.600 163 90.804 91.837 89.799
33 18.410 19.378 17.389 99 55.157 56.179 54.150 164 91.361 92.393 90.361
34 18.967 19.936 17.967 100 55.713 56.737 54.713 165 91.917 92.951 90.913
35 19.523 20.494 18.503 101 56.270 57.293 55.264 166 92.475 93.508 91.475
36 20.080 21.053 19.080 102 56.828 57.850 55.828 167 93.032 94.066 92.027
37 20.636 21.611 19.617 103 57.384 58.408 56.378 168 93.588 94.623 92.588
38 21.193 22.169 20.193 104 57.941 58.965 56.941 169 94.147 95.179 93.141
39 21.749 22.727 20.730 105 58.499 59.523 57.492 170 94.703 95.737 93.703
40 22.306 23.286 21.306 106 59.056 60.079 58.056 171 95.260 96.294 94.255
41 22.862 23.844 21.844 107 59.612 60.636 58.606 172 95.816 96.850 94.816
42 23.419 24.402 22.419 108 60.169 61.194 59.169 173 96.374 97.409 95.370
43 23.975 24.960 22.958 109 60.727 61.751 59.720 174 96.931 97.965 95.931
44 24.532 25.519 23.532 110 61.283 62.309 60.283 175 97.487 98.522 96.484
45 25.088 26.077 24.072 111 61.840 62.865 60.834 176 98.046 99.080 97.046
46 25.645 26.633 24.645 112 62.396 63.422 61.396 177 98.602 99.636 97.598
47 26.201 27.192 25.186 113 62.955 63.980 61.948 178 99.159 100.193 98.159
48 26.758 27.750 25.758 114 63.511 64.537 62.511 179 99.715 100.751 98.712
49 27.314 28.308 26.300 115 64.068 65.095 63.062 180 100.273 101.308 99.273
50 27.871 28.866 26.871 116 64.624 65.651 63.624 181 100.830 101.864 99.826
51 28.427 29.423 27.414 117 65.182 66.208 64.176 182 101.386 102.422 100.386
52 28.984 29.981 27.984 118 65.739 66.766 64.739 183 101.945 102.979 100.940
53 29.540 30.539 28.528 119 66.295 67.323 65.290 184 102.501 103.535 101.501
54 30.097 31.096 29.097 120 66.854 67.879 65.854 185 103.058 104.094 102.054
55 30.653 31.654 29.641 121 67.410 68.437 66.404 186 103.614 104.650 102.614
56 31.211 32.212 30.211 122 67.967 68.994 66.967 187 104.172 105.207 103.168
57 31.768 32.769 30.755 123 68.523 69.552 67.518 188 104.729 105.765 103.729
58 32.324 33.327 31.324 124 69.081 70.109 68.081 189 105.285 106.321 104.282
59 32.881 33.885 31.869 125 69.638 70.665 68.632 190 105.844 106.878 104.844
60 33.437 34.442 32.437 126 70.194 71.223 69.194 191 106.400 107.436 105.396
61 33.996 35.000 32.983 127 70.753 71.780 69.746 192 106.957 107.993 105.957
62 34.552 35.557 33.552 128 71.309 72.336 70.309 193 107.513 108.549 106.510
63 35.109 36.115 34.097 129 71.866 72.895 70.860 194 108.071 109.107 107.071
64 35.665 36.673 34.665 130 72.422 73.451 71.422 195 108.628 109.664 107.624
65 36.222 37.230 35.211 131 72.980 74.009 71.974 196 109.184 110.220 108.184
66 36.778 37.788 35.778 132 73.537 74.566 72.537 197 109.743 110.779 108.738
67 37.336 38.344 36.325 133 74.093 75.122 73.088 198 110.299 111.335 109.299
68 37.893 38.903 36.893 134 74.650 75.681 73.650 199 110.856 111.892 109.853
69 38.449 39.459 37.439 135 75.208 76.237 74.202 200 111.414 112.450 110.414
70 39.006 40.017 38.006

E-179
 No. 160 Sprocket
2" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 3.402 3.952 2.111 71 45.214 46.370 44.079 136 86.588 87.764 85.463
6 4.000 4.664 2.875 72 45.852 47.008 44.727 137 87.224 88.402 86.094
7 4..610 5.352 3.369 73 46.488 47.644 45.352 138 87.862 89.038 86.737
8 5.226 6.028 4.101 74 47.124 48.282 45.999 139 88.498 89.676 87.367
9 5.848 6.696 4.635 75 47.760 48.918 46.625 140 89.134 90.312 88.009
10 6.472 7.356 5.347 76 48.396 49.556 47.271 141 89.770 90.948 88.640
11 7.100 8.012 5.902 77 49.034 50.192 47.898 142 90.408 91.586 89.283
12 7.728 8.664 6.603 78 49.670 50.830 48.545 143 91.044 92.222 89.913
13 8.358 9.314 7.171 79 50.306 51.466 49.171 144 91.680 92.858 90.555
14 8.988 9.962 7.863 80 50.942 52.104 49.817 145 92.316 93.496 91.187
15 9.620 10.608 8.442 81 51.580 52.740 50.444 146 92.945 94.132 91.829
16 10.252 11.254 9.127 82 52.216 53.378 51.091 147 93.590 94.768 92.460
17 10.844 11.898 9.713 83 52.852 54.014 51.718 148 94.226 95.406 93.101
18 11.518 12.542 10.393 84 53.488 54.652 52.363 149 94.864 96.042 93.733
19 12.152 13.186 10.985 85 54.124 55.288 52.991 150 95.500 96.680 94.375
20 12.784 13.828 11.659 86 54.762 55.924 53.637 151 96.136 97.316 95.006
21 13.420 14.470 12.256 87 55.398 56.562 54.264 152 96.772 97.952 95.647
22 14.054 15.110 12.929 88 56.034 57.198 54.909 153 97.410 98.590 96.280
23 14.688 15.752 13.529 89 56.670 57.836 55.537 154 98.046 99.226 96.921
24 15.322 16.392 14.197 90 57.308 58.472 56.183 155 98.682 99.862 97.553
25 15.958 17.032 14.801 91 57.944 59.110 56.810 156 99.320 100.500 98.195
26 16.592 17.672 15.467 92 58.580 59.746 57.455 157 99.956 101.136 98.826
27 17.228 18.312 16.073 93 59.216 60.384 58.083 158 100.592 101.772 99.467
28 17.862 18.950 16.737 94 59.854 61.020 58.729 159 101.230 102.410 100.099
29 18.498 19.590 17.346 95 60.490 61.656 59.357 160 101.866 103.046 100.741
30 19.134 20.228 18.009 96 61.126 62.294 60.001 161 102.502 103.682 101.372
31 19.768 20.868 18.619 97 61.764 62.930 60.630 162 103.138 104.320 102.013
32 20.404 21.506 19.279 98 62.400 63.568 61.275 163 103.776 104.956 102.646
33 21.040 22.146 19.891 99 63.036 64.204 61.903 164 104.412 105.592 103.287
34 21.676 22.784 20.551 100 63.672 64.842 62.547 165 105.048 106.230 103.919
35 22.312 23.422 21.164 101 64.308 65.478 63.176 166 105.686 106.866 104.561
36 22.948 24.060 21.823 102 64.946 66.114 63.821 167 106.322 107.504 105.192
37 23.584 24.698 22.437 103 65.582 66.752 64.449 168 106.958 108.140 105.833
38 24.220 25.336 23.095 104 66.218 67.388 65.093 169 107.596 108.776 106.465
39 24.856 25.974 23.710 105 66.856 68.026 65.723 170 108.232 109.414 107.107
40 25.492 26.612 24.367 106 67.492 68.662 66.367 171 108.868 110.050 107.738
41 26.128 27.250 24.983 107 68.128 69.298 66.996 172 109.504 110.686 108.379
42 26.764 27.888 25.639 108 68.764 69.936 67.639 173 110.142 111.324 109.012
43 27.400 28.526 26.256 109 69.402 70.572 68.269 174 110.778 111.960 109.653
44 28.036 29.164 26.911 110 70.038 70.210 68.913 175 111.414 112.596 110.285
45 28.672 29.802 27.529 111 70.674 71.846 69.542 176 112.052 113.234 110.927
46 29.308 30.438 28.183 112 71.310 72.482 70.185 177 112.688 113.870 111.558
47 29.944 31.076 28.802 113 71.948 73.120 70.815 178 113.324 114.506 112.199
48 30.580 31.714 29.455 114 72.584 73.756 71.459 179 113.960 115.144 112.831
49 31.216 32.352 30.075 115 73.220 74.394 72.089 180 114.598 115.780 113.473
50 31.852 32.990 30.727 116 73.856 75.030 72.731 181 115.234 116.416 114.105
51 32.488 33.626 31.348 117 74.494 75.666 73.362 182 115.870 117.054 114.745
52 33.124 34.264 31.999 118 75.130 76.304 74.005 183 116.508 117.690 115.388
53 33.760 34.902 32.621 119 75.766 76.940 74.645 184 117.114 118.326 116.019
54 34.396 35.538 33.271 120 76.404 77.576 75.279 185 117.780 118.964 116.651
55 35.032 36.176 33.894 121 77.040 78.214 75.908 186 118.416 119.600 117.291
56 35.670 36.814 34.545 122 77.676 78.850 76.551 187 119.054 120.236 117.924
57 36.306 37.450 35.167 123 78.312 79.488 77.181 188 119.690 120.874 118.565
58 36.942 38.088 35.817 124 78.950 80.124 77.825 189 120.326 121.150 119.197
59 37.578 38.726 36.440 125 79.586 80.760 78.455 190 120.964 122.146 119.839
60 38.214 39.362 37.089 126 80.222 81.398 79.097 191 121.600 122.784 120.471
61 38.852 40.000 37.713 127 80.860 82.034 79.728 192 122.236 123.420 121.111
62 39.488 40.636 38.363 128 81.496 82.670 80.371 193 122.872 124.056 121.744
63 40.124 41.274 38.986 129 82.132 83.308 81.001 194 123.510 124.694 122.385
64 40.760 41.912 39.635 130 82.768 83.944 81.643 195 124.146 125.330 123.017
65 41.396 42.548 40.259 131 83.406 84.582 82.274 196 124.781 125.966 123.656
66 42.032 43.186 40.907 132 84.042 85.218 82.917 197 125.420 126.604 124.290
67 42.670 43.822 41.532 133 84.678 85.854 83.547 198 126.056 127.240 124.931
68 43.306 44.460 42.181 134 85.314 86.492 84.189 199 126.692 127.876 125.564
69 43.942 45.096 42.806 135 85.952 87.128 84.820 200 127.330 128.514 126.205
70 44.578 45.734 43.453

E-180
 Sprocket No. 180
Diameter 2¼" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 3.828 4.446 2.234 71 50.866 52.166 49.448 136 97.412 98.735 96.006
6 4.500 5.247 3.094 72 51.583 52.884 50.177 137 98.128 99.452 96.715
7 5.186 6.021 3.650 73 52.299 53.600 50.880 138 98.844 100.106 97.438
8 5.879 6.782 4.473 74 53.015 54.317 51.609 139 99.560 100.886 98.148
9 6.579 7.533 5.073 75 53.730 55.033 52.313 140 100.276 101.601 98.870
10 7.281 8.276 5.875 76 54.446 55.751 53.040 141 100.992 102.317 99.580
11 7.986 9.014 6.499 77 55.162 56.466 53.745 142 101.708 103.034 100.302
12 8.693 9.747 7.287 78 55.879 57.184 54.473 143 102.425 103.750 101.012
13 9.402 10.478 7.927 79 56.594 57.899 55.177 144 103.140 104.465 101.734
14 10.112 11.207 8.706 80 57.310 58.617 55.904 145 103.857 105.183 102.445
15 10.822 11.934 9.357 81 58.027 59.333 56.610 146 104.573 105.899 103.167
16 11.533 12.661 10.127 82 58.743 60.055 57.337 147 105.289 106.614 103.877
17 12.245 13.385 10.787 83 59.459 60.766 58.042 148 106.005 108.332 104.599
18 12.957 14.110 11.551 84 60.175 61.484 58.769 149 106.721 108.047 105.309
19 13.670 14.834 12.217 85 60.891 62.199 59.474 150 107.438 108.765 106.032
20 14.383 15.557 12.977 86 61.607 62.915 60.201 151 108.154 109.481 106.742
21 15.096 16.279 13.648 87 62.323 63.632 60.907 152 108.870 110.196 107.464
22 15.810 16.999 14.404 88 63.039 63.348 61.633 153 109.586 110.914 108.174
23 16.524 17.721 15.079 89 63.755 65.066 62.339 154 110.302 111.629 108.896
24 17.238 18.441 15.832 90 64.471 65.781 63.065 155 111.018 112.345 109.607
25 17.952 19.161 16.511 91 65.187 66.499 63.771 156 111.734 113.063 110.328
26 18.666 19.881 17.260 92 65.903 67.214 64.497 157 112.451 113.778 111.039
27 19.381 20.601 17.942 93 66.619 67.932 65.203 158 113.167 114.494 111.761
28 20.096 21.319 18.690 94 67.335 68.648 65.929 159 113.883 115.211 112.471
29 20.810 22.039 19.374 95 68.051 69.363 66.636 160 114.599 115.927 113.193
30 21.525 22.757 20.119 96 68.767 70.081 67.361 161 115.315 116.642 113.904
31 22.240 23.477 20.806 97 69.483 70.796 68.068 162 116.031 117.360 114.625
32 22.955 24.194 21.549 98 70.199 71.514 68.793 163 116.747 118.076 115.336
33 23.670 24.914 22.237 99 70.916 72.230 69.500 164 117.464 118.791 116.058
34 24.385 25.632 22.979 100 71.631 72.947 70.225 165 118.180 119.509 116.768
35 25.101 26.350 23.669 101 72.348 73.663 70.933 166 118.896 120.224 117.490
36 25.816 27.068 24.410 102 73.064 74.378 71.658 167 119.612 120.942 118.201
37 26.531 27.785 25.101 103 73.780 75.096 72.365 168 120.328 121.658 118.922
38 27.246 28.503 25.840 104 74.496 75.812 73.090 169 121.044 122.373 119.633
39 27.962 29.221 26.533 105 75.212 76.529 73.798 170 121.760 123.091 120.354
40 28.677 29.939 27.271 106 75.928 77.245 74.522 171 122.477 123.806 121.065
41 29.393 30.656 27.965 107 76.644 77.960 75.230 172 123.193 124.522 121.787
42 30.108 31.374 28.702 108 77.360 78.678 75.954 173 123.909 125.240 122.498
43 30.824 32.092 29.397 109 79.073 79.394 76.662 174 124.625 125.955 123.219
44 31.539 32.810 30.133 110 78.792 80.111 77.386 175 125.341 126.671 123.930
45 32.255 33.527 30.830 111 79.508 80.827 78.095 176 126.057 127.388 124.651
46 32.971 34.243 31.565 112 80.225 81.542 78.819 177 126.774 128.104 125.363
47 33.686 34.961 32.262 113 80.931 82.260 79.527 178 127.490 128.819 126.084
48 34.402 35.678 32.996 114 81.657 82.976 80.251 179 128.206 129.537 126.795
49 35.118 36.396 33.694 115 82.373 83.693 80.959 180 128.922 130.253 127.516
50 35.834 37.114 34.428 116 83.089 84.409 81.683 181 129.638 130.968 128.227
51 36.549 37.829 35.126 117 83.805 85.124 82.392 182 130.354 131.686 128.948
52 37.265 38.547 35.859 118 84.521 85.842 83.115 183 131.071 132.401 129.660
53 37.981 39.265 36.558 119 85.237 86.558 83.824 184 131.787 133.117 130.381
54 38.696 39.980 37.290 120 85.953 87.273 84.547 185 132.503 133.835 131.092
55 39.412 40.698 37.990 121 86.670 87.991 85.256 186 133.219 134.550 131.813
56 40.128 41.416 38.722 122 87.386 88.706 85.980 187 133.935 135.266 132.524
57 40.844 42.131 39.422 123 88.102 89.424 86.689 188 134.651 135.983 133.245
58 41.560 42.849 40.154 124 88.818 90.140 87.412 189 135.367 136.699 133.957
59 42.276 43.567 40.855 125 89.534 90.855 88.121 190 136.084 137.414 134.678
60 42.991 44.282 41.585 126 90.250 91.573 88.844 191 136.800 138.132 135.389
61 43.707 45.000 42.287 127 90.966 92.288 89.553 192 137.516 138.848 136.110
62 44.423 45.716 43.017 128 91.682 93.004 90.276 193 138.232 139.563 136.822
63 45.139 46.433 43.719 129 92.399 93.722 90.986 194 138.948 140.281 137.542
64 45.855 47.151 44.449 130 93.115 94.437 91.709 195 139.664 140.996 138.254
65 46.571 47.867 45.151 131 93.831 95.155 92.418 196 140.381 141.712 138.975
66 47.287 48.584 45.881 132 94.547 95.870 93.141 197 141.097 142.430 139.686
67 48.003 49.300 46.584 133 95.263 96.586 93.850 198 141.813 143.145 140.407
68 48.719 50.018 47.313 134 95.979 97.304 94.573 199 142.529 143.861 141.119
69 49.435 50.733 48.016 135 96.695 98.019 95.283 200 143.245 144.578 141.839
70 50.151 51.451 48.745

E-181
 No. 200 Sprocket
2½" Pitch Diameter

Roller Chain Sprocket Diameters

No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
5 4.253 4.940 2.482 71 56.518 57.962 54.942 136 108.235 109.705 106.672
6 5.000 5.830 3.438 72 57.315 58.760 55.752 137 109.030 110.502 107.461
7 5.760 6.690 4.055 73 58.110 59.555 56.533 138 109.827 111.297 108.264
8 6.533 7.535 4.970 74 58.905 60.352 57.342 139 110.622 112.095 109.052
9 7.310 8.370 5.636 75 59.700 61.147 58.125 140 111.418 112.890 109.855
10 8.090 9.195 6.527 76 60.495 61.945 58.932 141 112.212 113.685 110.644
11 8.875 10.015 7.220 77 61.292 62.740 59.716 142 113.010 114.482 111.447
12 9.660 10.830 8.097 78 62.087 63.537 60.524 143 113.805 115.277 112.235
13 10.447 11.642 8.807 79 62.882 64.332 61.307 144 114.600 116.072 113.037
14 11.235 12.452 9.672 80 63.678 65.130 62.115 145 115.395 116.870 113.827
15 12.025 13.260 10.396 81 64.475 65.925 62.899 146 116.192 117.665 114.629
16 12.815 14.068 11.252 82 65.270 66.722 63.707 147 116.988 118.460 115.418
17 13.605 14.872 11.985 83 66.065 67.517 64.490 148 117.783 119.257 116.220
18 14.397 15.678 12.834 84 66.860 68.315 65.297 149 118.580 120.052 117.010
19 15.190 16.478 13.574 85 67.655 69.110 66.082 150 119.375 120.850 117.812
20 15.980 17.285 14.417 86 68.452 69.905 66.889 151 120.170 121.645 118.601
21 16.775 18.088 15.164 87 69.247 70.702 67.673 152 120.965 122.440 119.402
22 17.567 18.888 16.004 88 70.043 71.497 68.480 153 121.762 123.237 120.193
23 18.360 19.690 16.754 89 70.838 72.295 69.265 154 122.558 124.032 120.995
24 19.153 20.490 17.590 90 71.635 73.090 70.072 155 123.354 124.827 121.784
25 19.947 21.290 18.345 91 72.430 73.887 70.856 156 125.150 125.624 122.587
26 20.740 22.090 19.177 92 73.225 74.682 71.662 157 124.945 126.420 123.376
27 21.535 22.890 19.935 93 74.020 75.480 72.448 158 125.740 127.215 124.177
28 22.327 23.688 20.764 94 74.817 76.275 73.254 159 126.537 128.012 124.967
29 23.123 24.488 21.526 95 75.612 77.070 74.039 160 127.332 128.807 125.769
30 23.917 25.285 22.354 96 76.408 77.867 74.845 161 128.127 129.602 126.559
31 24.710 26.085 23.117 97 77.205 78.662 75.631 162 128.923 130.400 127.360
32 25.505 26.882 23.942 98 78.000 79.460 76.437 163 129.720 131.195 128.150
33 26.300 27.682 24.708 99 78.795 80.255 77.222 164 130.515 131.990 128.952
34 27.095 28.480 25.532 100 79.590 81.052 78.027 165 131.310 132.787 129.742
35 27.890 29.280 26.300 101 80.385 81.847 78.814 166 132.107 133.582 130.544
36 28.685 30.075 27.122 102 81.182 82.642 79.619 167 132.903 134.380 131.333
37 29.480 30.872 27.890 103 81.977 83.440 80.405 168 133.697 135.175 132.134
38 30.275 31.670 28.712 104 82.773 84.235 81.210 169 134.495 135.970 132.925
39 31.070 32.468 29.481 105 83.570 85.032 81.997 170 135.290 136.767 133.727
40 31.865 33.265 30.302 106 84.365 85.827 82.802 171 136.085 137.562 134.516
41 32.660 34.062 31.072 107 85.160 86.622 83.588 172 136.880 138.357 135.317
42 33.455 34.860 31.892 108 85.955 87.420 84.392 173 137.677 139.155 136.108
43 34.250 35.658 32.663 109 86.753 88.215 85.180 174 138.472 139.950 136.909
44 35.045 36.455 33.482 110 87.547 89.012 85.984 175 139.268 140.745 137.700
45 35.840 37.252 34.254 111 88.342 89.808 86.771 176 140.065 141.542 138.502
46 36.635 38.047 35.072 112 89.137 90.603 87.574 177 140.860 142.337 139.291
47 37.430 38.845 35.846 113 89.935 91.400 88.363 178 141.655 143.132 140.092
48 38.225 39.642 36.662 114 90.730 92.195 89.167 179 142.450 143.930 140.883
49 39.020 40.440 37.437 115 91.525 92.992 89.954 180 143.247 144.725 141.684
50 39.815 41.238 38.252 116 92.320 93.787 90.757 181 144.042 145.520 142.474
51 40.610 42.032 39.028 117 93.117 94.582 91.546 182 144.838 146.318 143.275
52 41.405 42.830 39.842 118 93.912 95.380 92.349 183 145.635 147.113 144.066
53 42.200 43.627 40.619 119 94.707 96.175 93.137 184 146.430 147.908 144.867
54 42.995 44.422 41.432 120 95.505 96.970 93.942 185 147.225 148.705 145.657
55 43.790 45.220 42.211 121 96.300 97.767 94.729 186 148.020 149.500 146.457
56 44.587 46.018 43.024 122 97.095 98.562 95.532 187 148.817 150.295 147.249
57 45.383 46.812 43.802 123 97.890 99.360 96.320 188 149.612 151.093 148.049
58 46.177 47.610 44.614 124 98.687 100.155 97.124 189 150.408 151.888 148.840
59 46.973 48.408 45.393 125 99.482 100.950 97.912 190 151.205 152.683 149.642
60 47.768 49.202 46.205 126 100.278 101.747 98.715 191 152.000 153.480 150.432
61 48.565 50.000 46.964 127 101.075 102.542 99.503 192 152.795 154.275 151.232
62 49.360 50.795 47.797 128 101.870 103.337 100.307 193 153.590 155.070 152.023
63 50.155 51.593 48.576 129 102.665 104.135 101.095 194 154.387 155.868 152.824
64 50.950 52.390 49.387 130 103.460 104.930 101.897 195 155.183 156.663 153.615
65 51.745 53.185 50.167 131 104.257 105.727 102.686 196 155.977 157.458 154.414
66 52.540 53.982 50.977 132 105.052 106.522 103.489 197 156.775 158.255 155.206
67 53.337 54.777 51.759 133 105.847 107.317 104.278 198 157.570 159.050 156.007
68 54.132 55.575 52.569 134 106.643 108.115 105.080 199 158.365 159.845 156.798
69 54.927 56.370 53.350 135 107.440 108.910 105.869 200 159.162 160.643 157.599
70 55.723 57.167 54.160

E-182
 Sprocket No. 240
Diameter 3" Pitch
Roller Chain Sprocket Diameters
No. of Pitch Outside Caliper No. of Pitch Outside Caliper No. of Pitch Outside Caliper
Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter Pitches Diameter Diameter Diameter
6 6.000 7.00 4.125 45 43.007 44.70 41.105 83 79.278 81.02 77.388
7 6.914 8.03 4.866 46 43.961 45.66 42.086 84 80.233 81.98 78.358
8 7.839 9.04 5.964 47 44.915 46.61 43.013 85 81.188 82.93 79.298
9 8.771 10.04 6.764 48 45.869 47.57 43.994 86 82.142 83.89 80.267
10 9.708 11.03 7.833 49 46.824 48.53 44.925 87 83.097 84.84 81.207
11 10.649 12.02 8.666 50 47.778 49.49 45.903 88 84.052 85.80 82.177
12 11.591 13.00 9.716 51 48.732 50.44 46.833 89 85.006 86.75 83.116
13 12.536 13.97 10.568 52 49.687 51.40 47.812 90 85.961 87.71 84.086
14 13.482 14.94 11.607 53 50.641 52.35 48.744 91 86.916 88.67 85.026
15 14.429 15.91 12.473 54 51.595 53.31 49.720 92 87.871 89.62 85.996
16 15.377 16.88 13.502 55 52.550 54.26 50.654 93 88.825 90.58 86.938
17 16.327 17.85 14.383 56 53.504 55.22 51.629 94 89.780 91.53 87.905
18 17.276 18.81 15.401 57 54.458 56.18 52.562 95 90.735 92.48 88.848
19 18.227 19.78 16.289 58 55.413 57.13 53.538 96 91.690 93.44 89.815
20 19.177 20.74 17.302 59 56.368 58.09 54.473 97 92.645 94.40 90.758
21 20.129 21.71 18.197 60 57.322 59.04 55.447 98 93.599 95.35 91.724
22 21.080 22.67 19.205 61 58.277 60.00 56.384 99 94.554 96.31 92.667
23 22.032 23.63 20.106 62 59.231 60.95 57.356 100 95.507 97.26 93.634
24 22.984 24.59 21.109 63 60.185 61.91 58.292 101 96.463 98.22 94.676
25 23.936 25.55 22.013 64 61.140 62.87 59.265 102 97.418 99.17 95.543
26 24.889 26.51 23.014 65 62.095 63.82 60.202 103 98.373 100.13 96.486
27 25.841 27.47 23.921 66 63.049 64.78 61.174 104 99.328 101.08 97.453
28 26.794 28.43 24.919 67 64.004 65.73 62.111 105 100.283 102.04 98.396
29 27.747 29.39 25.833 68 64.958 66.69 63.083 106 101.237 102.99 99.362
30 28.700 30.34 26.825 69 65.913 67.64 64.023 107 102.192 103.95 100.305
31 29.654 31.30 27.740 70 66.868 68.60 64.993 108 103.147 104.90 101.272
32 30.607 32.26 28.732 71 67.822 69.56 65.932 109 104.102 105.86 102.215
33 31.560 33.22 29.649 72 68.777 70.51 66.902 110 105.056 106.82 103.181
34 32.514 34.18 30.639 73 69.731 71.45 67.841 111 106.011 107.77 104.124
35 33.467 35.13 31.559 74 70.686 72.42 68.811 112 106.966 108.72 105.091
36 34.421 36.09 32.546 75 71.641 73.38 69.751 113 107.922 109.68 106.035
37 35.375 37.05 33.467 76 72.595 74.33 70.720 114 108.876 110.63 107.001
38 36.329 38.00 34.454 77 73.550 75.29 71.660 115 109.830 111.59 107.943
39 37.283 38.96 35.378 78 74.505 76.25 72.630 116 110.786 112.55 108.911
40 38.237 39.92 36.362 79 75.459 77.20 73.569 117 111.740 113.50 109.820
41 39.191 40.88 37.286 80 76.414 78.16 74.539 118 112.695 114.46 110.810
42 40.145 41.83 38.270 81 77.369 79.11 75.479 119 113.650 115.41 111.750
43 41.099 42.79 39.197 82 78.323 80.07 76.448 120 114.605 116.36 112.730
44 42.053 43.75 40.178

E-183