viewNitPdf 4487818

DYCE-C-BKN-ENGINEERING/NORTH WESTERN RLY
TENDER DOCUMENT
Tender No: NWR-SC-BKN-19-2023-24 Closing Date/Time: 08/04/2024 15:00
Dy.CE/C/BKN acting for and on behalf of The President of India invites E-Tenders against Tender No NWR-SC-BKN-19-2023-24
Closing Date/Time 08/04/2024 15:00 Hrs. Bidders will be able to submit their original/revised bids upto closing date and time only.
Manual offers are not allowed against this tender, and any such manual offer received shall be ignored.
1. NIT HEADER
Earthwork in filling and cutting in formation, blanketing, trolley refuges, toe,wall, retaining
wall, pitching, construction of Minor Bridges & LHS, FOB, Platform, Platform Shelters, S&T
Name of Work
structures,cable duct and other ancillary works between Sadulpur to Churu in Connection
with Churu- Sadulpur Doubling Project
Bidding type Two Stage Reverse Auction
Tender Type Open Bidding System Two Packet System
Tender Closing Date Time 08/04/2024 15:00 Date Time Of Uploading Tender 09/03/2024 14:20
Pre-Bid Conference
Yes Pre-Bid Conference Date Time 19/03/2024 11:00
Required
Advertised Value 934103518.54 Tendering Section GENERAL
Bidding Style Single Rate for Each Schedule Bidding Unit
Earnest Money (Rs.) 4820500.00 Validity of Offer ( Days) 90
Tender Doc. Cost (Rs.) 0.00 Period of Completion 18 Months
Contract Type Works Contract Category Expenditure
Are Joint Venture (JV) firms
Bidding Start Date 25/03/2024 Yes
allowed to bid
Ranking Order For Bids Lowest to Highest Expenditure Type Capital (Works)
Auto Elimination rules

Yes Minimum Decrement (%) .1
applicable
Initial Cooling Off Period Subsequent Cooling Off
04:00 00:20
(HH:MM) Period (HH:MM)
2. SCHEDULE
S.No. Item Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount Bidding Unit
Code
Above/
Schedule B-CPWD DSR-2021 Items 408534507.57
Below/Par
Please see Item Breakup for details. 1065239.04 (-) 38.00 660448.20
1
Description:- Chapter -01- Carriage of materilas
2
Description:- Chapter-02 -Earthwork
3
Description:- Chapter-04 - Concrete work
4
Description:- Chapter-05 Reinforced cement concrete
5
Description:- Chapter-06 Masonry work
6
Description:- Chapter-07 Stone work
7
Description:- Chapter-8 - Cladding work
8
Description:- Chapter-9 - Wood and PVC work
9 Description:- Chapter-10 Steel work
Pa g e 1 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

TENDER DOCUMENT
10
Description:- Chapter-11 -Flooring
11
Description:- Chapter-12-Roofing
12
Description:- Chapter-13-Finishing / Exterior Finishing
13
Description:- Chapter-15- Dismantling
14
Description:- Chapter-16-Road Work/ Roads
15
Description:- Chapter-17- Sanitary Installations
16
Description:- Chapter-18-Water Supply
17
Description:- Chapter-19 - Drainage / Stone ware pipes and fittings
18
Description:- Chapter-21-Aluminium work
19
Description:- Chapter-22- Water Proofing
20
Description:- Chapter-23- Rain Water Harvesting & Tubewells
21
Description:- Chapter-26-NEW TECHNOLOGIES AND MATERIALS
S.No. Item Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount Bidding
Code Unit
Above/
Schedule C-Non Schedule Items 48330155.14
Below/Par
NS1 126.00 cum 4061.22 511713.72 AT Par 511713.72
Description:- NS-1:-Casting, transporting and launching of precast reinforced concrete slabs in M-25 design mix
for RCC boxes including launching during traffic block or without traffic block etc. as per approved drawings &
design with contractors own materials such as sand, water, 6mm to 20mm well graded machine crushed stone
1 aggregate, admixtures etc. including machine mixing of all gradients, placing, mechanical vibrating, curing etc.
and providing shuttering, centering, formwork and handling, transporting to bridge sites including loading &
unloading and launching including supplying , laying and levelling of required layer of sand underneath RCC slab
as per approved drawing with contractors own abour and equipments, all lead, lift, royalties, taxes etc. complete in
all respect except cost of reinforcement & cement which will be paid separately under relevant USSOR items.
NS2 400.00 cum 5271.93 2108772.00 AT Par 2108772.00
Description:- NS-2 :-Casting and transporting precast reinforced cement concrete boxes and U-Type/L-Type
retaining wall segments in M30/35 design mix near LHS site with machine batched, machine mixed and machine
vibrated design mix concrete, including the cost of centering, shuttering, finishing, admixture, if required, as per IS:
2 9103 to retard setting of concrete/improve workability without impairing strength and durability as per direction of
Engineer-in-charge. Only machine mixed and automatic weigh batched concrete/ concrete produced by Fiori shall
be used during entire work. The concrete shall be placed with the help of mechanical means only. Rates are
inclusive of all the materials, labour, transporting to bridge sites including loading & unloading with contractors own
labour and equipments . curing, machinery, tools, plants, taxes etc. complete in all respect except cost of
reinforcement & cement which will be paid separately under relevant USSOR items.
NS3 997.00 MT 1746.12 1740881.64 AT Par 1740881.64
Description:- NS-3 :- Placement of precast reinforced cement concrete components (RCC box/U-Type/L-Type
3 segments of retaining walls) with the help of suitable capacity road crane at desired location during traffic block of
short duration with all contactor's labour, tools , material, cranes, machinery preparation of surface including cost
of filling of joints by epoxy mortar, cutting of lifting hooks by gas cutting, all lead, lift, taxes etc complete in all
respect.(a)-RCC box/U-type/L-type segments not requiring traffic block or in closed sections
NS4 4.00 Job 70518.27 282073.08 AT Par 282073.08

TENDER DOCUMENT
Description:- NS-4 :-Removing of existing any type of track for insertion of RCC boxes, laying,linking & lifting of
any type of track on newly laid RCC box on either side of LHS including cutting of rails, drilling of holes,
subsequent through packing to make track fit for 75 Kmph & de-stressing of LWR/CWR of any type of track and
picking up of stone ballast (new or retrieved) including loading & leading of ballast from stacks Various activities
involved in this work along with their tentative scope are:(i) Removing of existing track - 39.0 mtr (ii) Removing
ballastfrom track & keeping it away from site of work. (iii) After insertion of RCCboxes, putting back existing ballast
4 at (ii)above and supplying & putting in track additional quantity ofballast so as to provide minimum ballast cushion
of 300mm to 350mm in compacted condition.(iv) Re-laying & linking of track - 39.0 mtr (v) Lifting of track in stages
of 50/75 mm for required length to ensure ballast cushion of 300mm to350mm as per site conditions minimum
ballast supply 50.0cum on each LHS.(vi) Cutting of any type of rails - 4 to 8nos. (vii) Drilling of 31.75mm/26.5mm
or similar dia holes in rails of any section-16 nos (viii)Subsequent through packings to make track fit for 75Kmph-
50.0mtr either side ofLHS (ix) Local de-stressing of LWR/CWR 100.0m on either side of LHS. (x) AT welding of rail
joints on any type of rail on single rail/SWP/LWR with Railway prefabricated moulds and railway portions as per
IRS specifications T-19-2012 ( amended up todate) • Qty. and scope of work shown above at S.No. (i) to (x) are
tentative only. The scope of these items may vary as per site conditions & as per direction of Engineer-in-charge
for completing the work of LHS safely and successfully. The quoted rates are for complete job. Nothing extra shall
be paid on any account. Note UnitJ ob is taken for PerJob
NS5 4.00 Job 100669.60 402678.40 AT Par 402678.40
Description:- NS-5 :- Insertion and taking out of temporary service girder of required length as per need of site
below track in short duration traffic block as per Railway approved drawing to provide temporary arrangement for
5 casting of box/excavation of hard/rocky strata to make space for launching of RCC Box/for launching of RCC
componentsin subsequent blocks, including making and laying sleeper cribs, bearing plate, dismantling & laying of
track, cutting/filling of earth etc. as per standard drg. to make track fit for 20 Kmph speed, with contractors own
labour, crane, tools and plants etc. Nothing extra will be paid to the contractor except the accepted rate,
whatsoever.
NS6 14.00 cum 2643.58 37010.12 AT Par 37010.12
6 Description:- NS-6 :- Supplying & shrouding of pea gravel 2mm to 4mm size for tube well assembly according to
Rly. specifications based on ISI specification of tube well.
NS7 6784.00 Each 1247.21 8461072.64 AT Par 8461072.64
Description:- NS-7 :- Manufacturing, supplying & fixing of pr-fabricated RCC coping stone of size 530mm
7 x1125mm x100mm thick as per top face designed and approved by site Engineer with M-30 grade RCC with 8
mm dia. tor steel at 150mm c/cboth ways and manufactured by vibrocompaction process using jointless FRP/GRP
steel moulds of required size,shape & design. The item includes cost of cement, reinforcement, transportation etc.
(Note :Under layer of cement mortar to be laid as per site conditions & should be paid for separately).
NS8 3900.00 cum 5941.00 23169900.00 AT Par 23169900.00
Description:- NS-8 :-Casting, transporting and launching of Precast RCC Duct & connecting Chamber for cable
laying in M-25 design mix (with minimum cement content of 330 kg /cum) during traffic block or without traffic
block etc. as per approved drawings with contractor's own materials such as cement, sand, water, 6mm to 20mm
well graded machine crushed stone aggregate, admixtures etc. including machine mixing of all gradients, placing,
8 mechanical vibrating, curing etc. and handling, transporting to work sites including centering & shuttering, loading,
unloading and launching as per approved drawing with contractor's own labour and equipments, all lead, lift,
royalties, taxes etc. complete in all respect except cost of reinforcement which will be paid separately under
relevant DSR 2021 items. Note: Extra cement up to 10% of the minimum specified cement content in design mix
shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified
minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra
cement.
NS9 129290.00 cum 22.65 2928418.50 AT Par 2928418.50
Description:- NS-9 :-Extra for mechanical compaction of earthwork arising from usable cut spoils led into bank
9 with contracror's rollers of suitable capacity, type and size to achieve specified density as per specification, testing
as per IS codes including cost of water, T&P consumable material and all labour as a complete job. The work is to
be executed as per latest edition of "guidelines for earthwork in railway projects" issued by RDSO, Lucknow.
NS10 32.00 Each 15392.47 492559.04 AT Par 492559.04
Description:- NS-10 :-Constructing RCC chattery on Face wall/ corner over roof/ pillars as per approved plan with
10 Contractors own material and labour complete as per following specification cement concrete base 60 x 60 x 13
cm with 4 pillars of 13 x 13 x 90 cm with 15cm wide projected standing chajja around the pillars, with a Gumati of
45cm height from top dome. The total height of upto Gumti is 1.35m.
NS11 3600.00 Sqm 2276.41 8195076.00 AT Par 8195076.00
11
TENDER DOCUMENT
11
Description:- NS-11:- Supplying and fixing Galvanised Steel / Galvalume self supporting sheet in roofing made
from Mild steel having thickness minimum 0.80 BMT (Base Metal Thickness) having coating of Zinc / Aluminium +
Zinc including cutting to size and shape including fixing. The rates shall includes all cost of materials, taxes,
labour, tools, plants, fixture etc. complete and fixing as per direction of Engineer In Charge at site Note:- (1)
Contractor will have to be submit the design of the roofing duly proof checked from Govt. Engg College / IIT / NIT
for approval of the Railway. Roofing shall be provided only after getting it approved from the Railway. (2) In
design, CBE, NWR drawing No. CBE- 1017/RUB/ 2018/Roof Covering/R1 and CBE- 1017/RUB/ 2018/Roof
Covering/Sheet No. 1 may be refer for guidance purpose.
S.No. Item Code Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount Bidding Unit
Above/
Schedule D-Non Schedule Items ( Electrical General) 990508.00
Below/Par
NS1 825.00 Numbers 352.00 290400.00 AT Par 290400.00
Description:- NS-1:-Supply of material and wiring of LP/FP/Ex.Fan point with 1.5sqmm PVC single core multi-
1 stranded copper wire insulated concealed in stone/brick masonry wall in 19/20 mm PVC conduit with 1.5sqmm
PVC wire insulated copper for earth wire 1-way/2-way switch 5/6A as required and good quality ceiling rose
including connection (with modular swithch & celing rose). As per specification at Annexure-A.
NS2 285.00 Numbers 206.00 58710.00 AT Par 58710.00
2 Description:- NS-2:-Supply and fixing 5/6A plug, modular type 5-pin, 230V including modular swithch and with
modular board and wiring with 2.5sqmm PVC CU cable. As per specification at Annexure-A.
NS3 79.00 Numbers 258.00 20382.00 AT Par 20382.00
3 Description:- NS-3 :-Supply and fixing 15/16A plug, modular 5-pin 230V including modular swithch and with
modular board and wiring with 4.0 sqmm PVC CU cable As per specification at Annexure-A.
NS4 2320.00 Metre 56.00 129920.00 AT Par 129920.00
Description:- NS-4 :-Wiring of sub-main with 2 x 2.5sqmm PVC insulated, single core, multi-stranded copper
4
wire in PVC conduit concealed and 2.5sqmm PVC insulated, single core, multi-stranded copper wire for earth
wire. As per specification at Annexure-A.
NS5 810.00 Metre 96.00 77760.00 AT Par 77760.00
5
NS6 160.00 Metre 108.00 17280.00 AT Par 17280.00
6
NS7 50.00 Numbers 110.00 5500.00 AT Par 5500.00
7 Description:- NS-7:-Supply and fixing 2 module modular switch board plate for fixing of modular switches - plug
with sheet metal box of good quality concealed fixing of MS/PVC as per site engineer. As per specification at
Annexure-B.
NS8 79.00 Numbers 173.00 13667.00 AT Par 13667.00
Description:- NS-8 :-Supply and fixing 4 module modular switch board plate for fixing of modular switches -plug
8
Annexure-B.
NS9 78.00 Numbers 280.00 21840.00 AT Par 21840.00
Description:- NS-9 :-Supply and fixing 8 module modular switch board plate for fixing of modular switches -plug
9
Annexure-B.
NS10 153.00 Numbers 321.00 49113.00 AT Par 49113.00
10 Description:- NS-10:-Supply and fixing 12 module modular switch board plate for fixing of modular switches -
plug with sheet metal box of good quality concealed fixing of MS/PVC as per site engineer. As per specification at
Annexure-B.
NS11 169.00 Numbers 67.00 11323.00 AT Par 11323.00
11
Description:- NS-11:-Fixing of ceiling fan/TL fitting and connection. As per specification at Annexure-C.
NS12 157.00 Numbers 374.00 58718.00 AT Par 58718.00
12 Description:- NS-12 :-Supply and fixing of ceiling fan regulator electronic type 5-step. As per specification at
Annexure-D.
NS13 60.00 RM 108.00 6480.00 AT Par 6480.00
13 Description:- NS-13 :-Supply and fabricate of down rod suitable size with hole "A" Class GI Pipe for hanging fan.
As per specification at Annexure-E.

TENDER DOCUMENT
NS14 69.00 Numbers 55.00 3795.00 AT Par 3795.00

14 Description:- NS-14 :-Supply and fixing of Fan bracket/Hook by MS (Flat & Rod) for hanging the ceiling fan in
shelter/building etc. As per specification at Annexure-F.
NS15 60.00 Numbers 548.00 32880.00 AT Par 32880.00
15 Description:- NS-15:-Dismantlling of existing HT/LT Rail/PCC Poles/overhead span with fittings by digging the
foundation and transportation upto the required site. As per specification at Annexure-G.
NS16 20.00 Numbers 712.00 14240.00 AT Par 14240.00
Description:- NS-16:-Supply and fixing of stay complete with stay wire, stay insulator, stay rod, anchor plate,
16
straining screw including clamps nut bolts washers pipe piece 50mm dia, 1.5m long foundation and painting. . As
per specification at Annexure-H.
NS17 1000.00 Metre 98.00 98000.00 AT Par 98000.00
Description:- NS-17 :-Supply & laying of HDPE pipe 50 mm dia wall thickness 3 mm under the road/PF/in
17
ground or as per site requirement. The work involves digging of earth & laying of HDPE pipe. (As per
specification)
NS18 1500.00 Metre 23.00 34500.00 AT Par 34500.00
18 Description:- NS-18:- Laying, testing, commissioning & transportation of LT cable in Air/Pole/Pipe/wall/cable tray
etc. with complete lugs/glands and transportation of cable etc. Note- Cable will be supplied by Rly. from main
depot. As per specification.
NS19 1000.00 Metre 46.00 46000.00 AT Par 46000.00
Description:- NS-19:-Digging & filling of trench size 0.4m wide x 0.8m deep. Trench work may be on
19
kuchha/pucca land and all type of soil as per site requirement and without protective layer of bricks. Surface of
trench shall be made good in all respect and upto satisfaction of site engineer. As per specification.
Code Unit
Above/
Schedule A1-IRUSSOR 2021 items ( Chapter -1 - Earthwork) 372658819.20
Below/Par
011010 381433.00 100 Sqm 488.56 1863529.06 (-) 12.53 1630028.87
Description:- Preparation of foundation for Embankment by clearing, grubbing, stripping top soil (average 150
1 mm) and stacking beyond foundation area, thereafter ploughing and pulverizing 150 - 200 mm of top of soil with
tractor trolley, mixing water to achieve OMC with water sprinkler or left for natural drying, as required, and
compaction with vibratory roller of suitable capacity to achieve 98% MDD for laying first layer of soil for
embankment construction.
011020 42.00 Kilometre 113367.92 4761452.64 (-) 12.53 4164842.62
Description:- Benching of existing embankment manually in steps of 30 cm height for doubling/tripling works in
running line to provide proper amalgamation between the old and new embankments as per RDSO latest
Specifications and guidelines RDSO/2020//GE: IRS-0004 to the entire satisfaction of Engineer in-charge. The item
includes uprooting and disposing of all the vegetation, all lift, descends, ascends and additional earthwork required
2 for filling due to removal of earth in benching in existing bank. Note: (1) The benching Work shall be done for a
maximum height of 0.90 m at any time based on the progress of earthwork starting from toe of the embankment.
(2) Benching work shall be certified and recorded before starting the earth work. (3) Unit for payment shall be km
per metre height of the Bank. Height here means representative average height of the bank in the specified km
taken from cross sectional measurements for earthwork. (4) Since the rate includes earthwork in steps, payment
under this item shall be made after completion of earthwork to that level. (5) Cut soil from bank shall not be used in
embankment construction and disposed off away from bank as per the direction of Engineer-in-charge.
011032 188862.00 cum 227.72 43007654.64 (-) 12.53 37618795.51
Description:- Earthwork in filling in embankment, guide bunds, around buried type abutments, bridge gaps, trolley
refuges, platforms etc. with contractor's own earth conforming to Soil Quality Class SQ1/SQ2/SQ3, after
preparation of foundations as applicable, benching in existing banks wherever required, spreading in layers with
motor grader, bringing the moisture content to OMC, mechanical compaction to specified density and dressing of
3 bank to final profile as per RDSO Specifications: RDSO/2020/GE: IRS-0004 with latest correction slips. Note: 1)
Foundation preparation, Benching including additional earthwork on account of this, wherever required, shall be
paid extra under relevant schedule item for benching. 2) Payment for Earthwork under this item shall be made
based on the cross section measurements calculated (i) with original ground profile of existing bank based on
initial ground levels before doing benching and (ii) final profile of the bank worked out with final levels as per
prevailing guidelines. Using Soil Class SQ2
012011 234683.60 cum 107.39 25202671.80 (-) 12.53 22044777.02

TENDER DOCUMENT
Description:- Earthwork in cutting in formation, trolley refuges, side drains, level crossing approaches, platforms,
catch water drains, diversion of nallah & finishing to required dimension and slopes to obtain a neat appearance to
4 standard profile inclusive of all labour, materials, plant & machinery, leading all cut spoils either to make spoil
dumps or for filling in embankment with leads within 2 km on either side of edge of the cutting(s) including all lifts,
ascent, descent, loading, unloading, bailing & pumping out water, if required, clearance of site and all other works
incidental thereto for completing the work as per RDSO Specification No. RDSO/2020/GE: IRS-0004 with latest
updated correction slips and to the satisfaction of the Engineer-in-Charge. Note: (i) All usable earth arising from
cut spoils shall be led into bank formation and Unusable spoils shall be dumped / stacked away from toe of
embankment. (ii) All hard rock /and boulders not fit for filling will be stacked by the contractor and will be property
of the Railways. (iii)Cut trees shall be property of Railways and to be deposited in the railway godown unless
specified otherwise in the Conditions of Contract. In all conditions and classifications of soil except rock
012015 84000.00 cum 5.42 455280.00 (-) 12.53 398233.42
Description:- Earthwork in cutting in formation, trolley refuges, side drains, level crossing approaches, platforms,
catch water drains, diversion of nallah & finishing to required dimension and slopes to obtain a neat appearance to
standard profile inclusive of all labour, materials, plant & machinery, leading all cut spoils either to make spoil
dumps or for filling in embankment with leads within 2 km on either side of edge of the cutting(s) including all lifts,
ascent, descent, loading, unloading, bailing & pumping out water, if required, clearance of site and all other works
5 incidental thereto for completing the work as per RDSO Specification No. RDSO/2020/GE: IRS-0004 with latest
updated correction slips and to the satisfaction of the Engineer-in-Charge. Note: (i) All usable earth arising from
cut spoils shall be led into bank formation and Unusable spoils shall be dumped / stacked away from toe of
embankment. (ii) All hard rock /and boulders not fit for filling will be stacked by the contractor and will be property
of the Railways. (iii)Cut trees shall be property of Railways and to be deposited in the railway godown unless
specified otherwise in the Conditions of Contract. Extra for leading of Cut spoil every one km beyond original lead
of 2 km over item nos. 012011 to 012014
012030 190968.00 cum 1728.03 329998433.04 (-) 12.53 288649629.38
Description:- Mechanical manufacturing of blanketing material by using only hard and durable stone crushed in
mechanical crusher to different gradations, wet mixing of the same in designed proportion in Pug mill or wet mix
6 plant to have uniform gradation including all incidental transportation, laying over finished formation in uniform
layer(s) with motor grader, compaction with suitable vibratory roller to specified density and finishing to correct
profile, complete as per RDSO Specification No. RDSO/2020/GE: IRS-0004 with latest correction slips. Note: This
item shall be used only when entire constituent of blanketing material is mechanically manufactured by crushing of
hard and durable stone into desired gradation of designed proportion.
013021 75045.00 100 Sqm 6513.75 4888243.69 (-) 12.53 4275746.76
Description:- Turfing / planting, including all lead & lift and watering as required until properly rooted with. Note:
7
Initially payment of only 40% will be made. Balance 60% will be paid after 3 months of maintenance period, only if
the turfing is properly rooted on entire turfed area. Turfing with sods, 10cm thick and 20cm square closely laid.
013041 60000.00 Metre 264.41 15864600.00 (-) 12.53 13876765.62
Description:- Providing portable fencing along running track where work is to be done in close vicinity of track,
maintaining during execution of work and removing after completion of the work as per direction of the Engineer.
8 Fencing shall consist of self supporting steel angles of size 50mm x 50mm x 6mm, 1.5m long provided with hooks
etc. and embedded in CC 1:2:4 block of size 0.23m x 0.23m x 0.23m placed at c/c distance of 2m along track.
12mm dia rods in three horizontal layers shall be tack welded with angle posts. Note : Released material will be
property of the contractor after completion of work. Cost of cement required for CC blocks shall be paid separately.
With provision of one 50mm wide retro-reflective tape in horizontal direction, duly secured/tight with vertical posts.
Code Unit
Above/
Schedule A2 --IRUSSOR 2021 items ( All chapters other than Schedule A1) 103589528.63
Below/Par
022011 4103.00 cum 210.90 865322.70 (-) 12.53 756897.77
Description:- Earthwork in excavation by mechanical means (Hydraulic Excavator)/Manual Means for foundations
and floors of the bridges, retaining walls etc. including setting out, dressing of sides, ramming of bottom, getting
out the excavated material, back filling in layers with approved material and consolidation of the layers by ramming
1 and watering etc. including all lift, disposal of surplus soil up to a lead of 300m, all types of shoring and strutting
with all labour and material complete as per drawing and technical specification as directed by Engineer in charge.
Note: This item will be used for excavation work in connection with other miscellaneous works also like side drains,
foundation for OHE masts and other miscellaneous structures in connection with Gauge Conversion, Doubling,
New lines. All kinds of soils
022032 841.00 cum 2936.59 2469672.19 (-) 12.53 2160222.26
Description:- Providing and laying in position Plain cement concrete of specified Nominal Mix for miscellaneous
2 works like side drains, foundation for OHE masts and other miscellaneous structures excluding the cost of
Cement, centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4
graded stone aggregate 20 mm nominal size)

TENDER DOCUMENT
022035 135.00 cum 2944.12 397456.20 (-) 12.53 347654.94

Description:- Providing and laying in position Plain cement concrete of specified Nominal Mix for miscellaneous
3 works like side drains, foundation for OHE masts and other miscellaneous structures excluding the cost of
Cement, centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6
graded stone aggregate 40 mm nominal size).
022040 1818.00 cum 2919.59 5307814.62 (-) 12.53 4642745.45
Description:- Providing and laying in position machine batched, machine mixed and machine vibrated Cement
Concrete of specified grade as per approved Design Mix (mixed in Mobile Concrete Batching/Mixing Plant at site
or RMC from approved plants) using 20mm graded crushed stone aggregate and coarse sand of approved quality
4 in RCC raft foundation & Pile cap including finishing, using Plasticiser in approved proportions (as per IS:9103), to
modify workability without impairing strength and durability complete as per specifications and direction of the
Engineer in charge. Note: 1. Payment for cement, reinforcement and shuttering shall be made extra under
relevant item. 2. Plasticiser shall invariably be used in approved proportion to increase workability with minimum
possible quantity of cement for all grade of Design Mix Concrete unless it is specifically approved citing reasons
for not using plasticiser at the stage of Mix Design and in that case deduction shall be made as per relevant item.
022052 2006.00 cum 2999.09 6016174.54 (-) 12.53 5262347.87
Concrete of specified grade as per approved Design Mix (mixed in Mobile Concrete Batching/Mixing Plant at site
or RMC from approved plants) using 20mm graded crushed stone aggregate and coarse sand of approved quality
for the following Reinforced cement concrete structural elements up to height of 9.0 m from foundation top level,
5 including finishing, using Plasticiser in approved proportions (as per IS:9103), to modify workability without
impairing strength and durability complete as per specifications and direction of the Engineer in charge. Note: 1.
Payment for cement, reinforcement and shuttering shall be made extra under relevant item. 2. Plasticiser shall
invariably be used in approved proportion to increase workability with minimum possible quantity of cement for all
grade of Design Mix Concrete unless it is specifically approved citing reasons for not using plasticiser at the stage
of Mix Design and in that case deduction shall be made as per relevant item. Wing wall and Return wall
022060 13.00 cum 2988.17 38846.21 (-) 12.53 33978.78
Description:- Providing and laying Plain Cement Concrete 1:3:6 with graded stone aggregate of 40mm nominal
6 size, in foundation and floors, retaining walls of bridges including mechanical mixing, vibrating, pumping and
bailing out water where ever required with all materials and labour complete but excluding the cost of cement and
shuttering as per drawings and technical specifications as directed by Engineer.
022070 40.00 Metre 262.24 10489.60 (-) 12.53 9175.25
7 Description:- Providing and fixing Weep Holes in Abutments, Wing walls and Return walls etc., of new bridges
with 110mm dia UPVC pipe Type A ISI marked with all contractor's men, material, transportation, all taxes as per
specifications and as directed by Engineer-in-Charge.
023041 351.00 cum 179.45 62986.95 (-) 12.53 55094.69
Description:- Dry/Wet Sinking of Circular Wells (Other than pneumatic method) in all types of strata except hard
8 rock requiring blasting including bailing and pumping out water, removal of excavated soil with all labour and
material required for sinking as per drawing and direction of the Engineer in charge, disposal of surplus soil in the
adjoining bank/embankment. From initial level of cutting edge & up to 3m depth
023042 472.00 cum 289.99 136875.28 (-) 12.53 119724.81
Description:- Dry/Wet Sinking of Circular Wells (Other than pneumatic method) in all types of strata except hard
9 rock requiring blasting including bailing and pumping out water, removal of excavated soil with all labour and
material required for sinking as per drawing and direction of the Engineer in charge, disposal of surplus soil in the
adjoining bank/embankment. Above 3m to 10m depth
023092 112.00 cum 3211.55 359693.60 (-) 12.53 314623.99
Concrete of specified grade as per approved Design Mix (Cast in-Situ) using 20mm graded crushed stone
aggregate and coarse sand of approved quality in the following elements of well including finishing, using
10 Plasticiser in approved proportions (as per IS:9103), to modify workability without impairing strength and durability
complete as per drawings and technical specifications as directed by Engineer. Note: 1. Payment for cement,
reinforcement and shuttering shall be made extra under relevant item. 2. Plasticiser shall invariably be used in
approved proportion to increase workability with minimum possible quantity of cement for all grade of Design Mix
Concrete unless it is specifically approved citing reasons at the stage of Mix Design and in that case deduction
shall be made as per relevant item. In Steining of wells
023096 21.46 cum 3065.57 65787.13 (-) 12.53 57544.00
11
TENDER DOCUMENT
11 Description:- Providing and laying in position machine batched, machine mixed and machine vibrated Cement
Concrete of specified grade as per approved Design Mix (Cast in-Situ) using 20mm graded crushed stone
aggregate and coarse sand of approved quality in the following elements of well including finishing, using
Plasticiser in approved proportions (as per IS:9103), to modify workability without impairing strength and durability
complete as per drawings and technical specifications as directed by Engineer. Note: 1. Payment for cement,
reinforcement and shuttering shall be made extra under relevant item. 2. Plasticiser shall invariably be used in
approved proportion to increase workability with minimum possible quantity of cement for all grade of Design Mix
Concrete unless it is specifically approved citing reasons at the stage of Mix Design and in that case deduction
shall be made as per relevant item. In Well cap and corbel, if provided
024010 719.00 cum 3211.55 2309104.45 (-) 12.53 2019773.66
Description:- Providing and casting machine batched, machine mixed and machine vibrated Cement Concrete of
specified grade as per approved Design Mix, mixed in Mobile Concrete Batching/Mixing Plant at site or RMC from
approved plants, (Cast in-Situ/Pre-cast) in bottom/top slab, side walls, toe wall and sumps haunch filling head
walls, thrust bed or any other component using 20mm graded crushed stone aggregate and coarse sand of
12 approved quality of RCC box of any size including finishing, Plasticiser in approved proportions (as per IS:9103),
to modify workability without impairing strength and durability, complete as per drawings and technical
specifications as directed by Engineer in charge. Note: 1. Payment for cement, reinforcement and shuttering shall
be made extra under relevant item. 2. Plasticiser shall invariably be used in approved proportion to increase
workability with minimum possible quantity of cement for all grade of Design Mix Concrete unless it is specifically
approved citing reasons at the stage of Mix Design and in that case deduction shall be made as per relevant item.
024020 30.00 cum 2919.59 87587.70 (-) 12.53 76612.96
Description:- Providing and laying in position machine batched, machine mixed and machine vibrated Design Mix
Cement Concrete, mixed in Mobile Concrete Batching/Mixing Plant at site or RMC from approved plants, of
13 specified grade (cast in-situ) using 20mm graded crushed stone aggregate and coarse sand of approved quality in
Drop and curtain wall and alike structures below bed level, complete in all respect as per drawings and technical
specifications to the satisfaction of Engineer-in-Charge. Note: Payment for cement, reinforcement and shuttering
shall be made extra.
025020 1406.00 Sqm 178.84 251449.04 (-) 12.53 219942.48
14 Description:- Providing and applying two coats of coal tar or bitumen confirming to IS:3117- latest version on the
top and sides of RCC box/slabs @ 1.70 kg/sqm after cleaning the surface with all labour and materials complete
job as directed by the Engineer.
025031 8201.00 Sqm 715.17 5865109.17 (-) 12.53 5130210.99
15 Description:- Centering and shuttering including strutting, propping etc. and removal of form for : All types of
bridge sub-structures, e.g. pier, abutment, wing wall, retaining wall, RCC box type foundations, Abutment cap, Pier
Cap, Inspection Platform & Pedestal over Pier cap, Fender wall, Diaphragm wall etc. up to 5m above ground level
025032 1146.10 Sqm 927.65 1063179.66 (-) 12.53 929963.25
16 Description:- Centering and shuttering including strutting, propping etc. and removal of form for : All types of
bridge super-structures, e.g. slabs, I-girders, T-girders, Box girders etc. up to 5m above ground level.
025071 2051.00 MT 7801.51 16000897.01 (-) 12.53 13995984.61
17
Description:- Supply and using Cement at Worksite Ordinary Portland Cement 43 grade approved brands/makes
025073 452.00 MT 7294.44 3297086.88 (-) 12.53 2883961.89
18
Description:- Supply and using Cement at Worksite Pozzolana Portland Cement approved brands/makes
025082 591623.00 Kg 107.01 63309577.23 (-) 12.53 55376887.20
19 Description:- Supply of steel reinforcement of approved brands/makes for R.C.C. work including straightening,
cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-
500D or more of approved brands/makes.
031163 45.00 MT 180.67 8130.15 (-) 12.53 7111.44
Description:- Loading, transportation of Precast RCC Girders / Slabs / Ballast retainers / Steel Girders etc. from
20
Casting Yard to Site of Work, unloading and stacking at site of work at prescribed location as directed by
Engineer-in-Charge up to 60 kms. Above 10 km up to 15 km
031165 90.00 MT 235.62 21205.80 (-) 12.53 18548.71
21 Description:- Loading, transportation of Precast RCC Girders / Slabs / Ballast retainers / Steel Girders etc. from
Engineer-in-Charge up to 60 kms. Above 20 km up to 25 km
031175 18000.00 MT-Km 5.00 90000.00 (-) 12.53 78723.00
22 Description:- Loading, transportation of Precast RCC Girders / Slabs / Ballast retainers / Steel Girders etc. from
Engineer-in-Charge above 60 kms. Above 200 km
041370 35.00 MT 129631.69 4537109.15 (-) 12.53 3968609.37

TENDER DOCUMENT
Description:- Supplying fabricating and erecting welded and/or bolted and/or riveted steel work in built up
sections, trusses and framed work, staging, racks, Height Gauge etc. for Steel Structures other than bridge
23 girders, using RSJ, tees, angles and channels/flats, plates, gussets, round or square bars, cleats, bolts etc., with
contractors own steel including cutting, bending, straightening, drilling, riveting, hoisting, fixing, erecting, welding,
bolting etc., with Providing stiffeners wherever required as per approved drawing including applying a priming coat
of a approved steel primer with all contractor's materials, labour, tools & plants, lead & lift including crossing of
tracks if required etc., complete as per specification and as directed by Engineer-in-charge. Note: The payment
shall be made on the theoretical weight of main components and gusset plates only.
052010 19.50 cum 2887.37 56303.71 (-) 12.53 49248.86
Description:- Providing and laying flooring with rubble stone, laid over 15cm thick CC 1:2:4 and the voids filled
24 with CC 1:2:4 complete with the joints pointed with 1:2 Cement Sand mortar as per drawing and Technical
specifications. Payment for cement to be done separately. Voids in the rubble stone to be taken as 35% of the
gross volume of the stone layer. Note: Base concrete shall be paid extra under relevant item.
052030 47.00 cum 1154.27 54250.69 (-) 12.53 47453.08
Description:- Supply and laying of quarry dust including consolidation, supply of all materials, labour, lead, lift,
25
tools, plants, crossing of tracks as per drawing and technical specification as directed by the Engineer in charge in
case loose slush is encountered at site of foundation before casting the foundation or laying the filtering media.
052150 993.00 cum 2577.00 2558961.00 (-) 12.53 2238323.19
26 Description:- Providing and laying of filter media consisting of granular materials of GW, GP, SW groups as per
IS:1498 (latest) in required profile behind boulder filling of abutments, wing walls / return walls etc. above bed level
with all labour and material complete job as per drawing and technical specification of RDSO Guidelines.
052200 4.00 Each 303.85 1215.40 (-) 12.53 1063.11
27 Description:- Painting the HFL mark and Danger level mark, year of HFL on bridge abutments and piers with
ready mixed paint as per standard in two coats over one coat of primer with all materials, labour, tools, scaffolding,
all lead and lift etc. including writing complete.
052210 11.00 Each 869.26 9561.86 (-) 12.53 8363.76
Description:- Providing cast in situ bridge number plaques as per Railway drawing in cement concrete 1:2:4 mix
28 using 20mm hard stone aggregate embedded in 30mm notch in Bridge parapet coping duly engraving the letter
and figures and an arrow indicating the direction of flow and finishing the top exposed surface with cement mortar
1:3, painting letters and figures with two coats of black enamel paint on two coats of white background with all
labour, tools, cement, paint etc. with all leads and lifts.
052250 1672.00 cum 411.68 688328.96 (-) 12.53 602081.34
29 Description:- Providing Boulder Backing behind wing wall, return wall, retaining wall with hand packed boulders &
cobbles with smaller size boulders toward the back including all lead, lift, labour & other incidental charges as
complete work in all respect. Payment for boulder/cobbles will be done extra.
211201 720.00 Hour 864.02 622094.40 (-) 12.53 544145.97
Description:- Hiring of machinery for minor miscellaneous works for short duration including operator/driver, fuel,
30 lubricants and consumable. The contractor shall arrange all statutory permits as required by rules and regulations
prevailing in the area of work. Payment shall be made for actual working hours at site. JCB Backhoe Loaders 3DX
Plus or similar with minimum 1.10 cum bucket capacity
211202 300.00 Hour 964.49 289347.00 (-) 12.53 253091.82
Description:- Hiring of machinery for minor miscellaneous works for short duration including operator/driver, fuel,
31 lubricants and consumable. The contractor shall arrange all statutory permits as required by rules and regulations
prevailing in the area of work. Payment shall be made for actual working hours at site. Hydra or similar tyre
mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material
031130 466.00 cum 3384.16 1577018.56 (-) 12.53 1379418.13
Description:- Casting and installation of single/twin RCC box of all sizes with or without common web section after
supporting the track on temporary girders including design of pushing scheme, thrust bed, casting of all RCC
components, with specified grade of controlled concrete, pushing it in correct position and alignment below
Railway track/Road following all measures of track safety by 'Air pushing technique" as per approved
drawings/scheme, in all types of soils with disposal of surplus earth away from vent up to 1 Km, fixing arrangement
for all services & utilities including parapet walls on both sides, wearing course, foot paths, plaques, drainage
32 arrangements etc. and all other incidental works to complete the ROB/RUB/Canal crossing in all respect as per
specifications to the satisfaction of Engineer-in-Charge. Note: (1) The rate includes all items of work/supplies for
complete job in all respects except "cost of Reinforced cement concrete, cement, reinforcement & shuttering" of (i)
main RCC Box; (ii) Thrust Bed; (iii) Footpath (iv) Parapet wall and (v) wearing Course only, which shall be paid
extra under relevant items of USSOR. (2) The CC Cribs as required and Temporary Girder shall be supplied by
Railways at available location. (3) Transportation of Temporary Girder to site shall be paid separately under
relevant item.. (4) The payment for this item shall be made for the clear inner cross section area of the parent
RCC Box/Boxes and barrel length i.e. clear inner volume of parent RCC Box/Boxes.

TENDER DOCUMENT
3. ITEM BREAKUP
Schedule Schedule B-CPWD DSR-2021 Items

Item- 1 Chapter -01- Carriage of materilas
S No. Item No Description of Item Unit Qty Rate Amount
1.0 CARRIAGE OF MATERIALS
By Mechanical Transport including loading,unloading
1.1
and stacking
1.1.1 Lime, moorum, building rubbish
1 1.1.1.2 2km cum 6528 163.18 1065239.04
Total 1065239.04
Item- 2 Chapter-02 -Earthwork
2.0 EARTH WORK
Earth work in excavation by mechanical means
(Hydraulic excavator)/manual means over areas
(exceeding 30 cm in depth, 1.5 m in width as well as 10
2.6
sqm on plan) including getting out and disposal of
excavated earth lead upto 50 m and lift upto 1.5 m, as
directed by Engineer-in-charge.
1 2.6.1 All kinds of soil cum 29063 205.45 5970993.35
Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10
2.8 sqm on plan), including dressing of sides and ramming
of bottoms, lift upto 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m.
2 2.8.1 All kinds of soil. cum 14560 286.85 4176536
2.25 Filling available excavated earth (excluding rock) in cum 30536 253.95 7754617.2
trenches, plinth, sides of foundations etc. in layers not
3 exceeding 20cm in depth, consolidating each deposited
layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
2.25A Excavating, supplying and filling of local earth (including cum 4044 368.65 1490820.6
royalty) by mechanical transport upto a lead of 5km also
4 including ramming and watering of the earth in layers not
exceeding 20 cm in trenches, plinth, sides of foundation
etc. complete.
Total 19392967.15
Item- 3 Chapter-04 - Concrete work
4.0 CONCRETE WORK
4.1S CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position cement concrete of
4.1 specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from cum 814 7365.15 5995232.1
1 natural sources : 4 graded stone aggregate 20 mm
nominal size derived from natural sources)
4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from cum 2236 6833.4 15279482.4

TENDER DOCUMENT
Providing and laying cement concrete in retaining walls,

return walls, walls (any thickness) including attached
pilasters, columns, piers, abutments, pillars, posts,
4.2 struts, buttresses, string or lacing courses, parapets,
coping, bed blocks, anchor blocks, plain window sills,
fillets, sunken floor etc., up to floor five level, excluding
the cost of centering, shuttering and finishing:
4.2.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived cum 50 9793.75 489687.5
4 from natural sources : 3 graded stone aggregate 20 mm
nominal size derived from natural sources).
Centering and shuttering including strutting, propping
4.3
etc. and removal of form work for :
6 4.3.1 Foundations, footings, bases for columns Sqm 17773 307.95 5473195.35
4.3.2 Retaining walls, return walls, walls (any thickness) Sqm 33813 669.55 22639494.15
7 including attached pilasters, buttresses, plinth and string
courses fillets, kerbs and steps etc.
4.10S DAMP-PROOF COURSE
4.13 Providing & applying a coat of residual petroleum Sqm 31309 113.85 3564529.65
bitumen of grade of VG-10 of approved quality using
8 1.7kg per square metre on damp proof course after
cleaning the surface with brushes and finally with apiece
of cloth lightly soaked in kerosene oil.
4.14S MISCELLANEOUS
Providing and laying in position ready mixed or site
batched design mix cement concrete for plain cement
concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland
Pozzolana/Ordinary Portland /Portland Slag cement,
admixtures in recommended proportions as per IS: 9103
to accelerate / retard setting of concrete, to improve
durability and workability without impairing strength;
including pumping of concrete to site of laying, curing,
4.20
carriage for all leads; but excluding the cost of centering,
shuttering and finishing as per direction of the engineer-
in-charge; for the following grades of concrete. Note:
Extra cement up to 10% of the minimum specified
cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 110% of the minimum specified cement
content, the contractor shall have discretion to either re-
design the mix or bear the cost of extra cement.
4.20.1 All works upto plinth level :
4.20.1.3 Concrete of M20 grade with minimum cement content of cum 3317 8387.15 27820176.55
9
270 kg /cum
10
300 kg /cum
4.20.2 All works above plinth and upto floor V level :
11
300 kg /cum
Total 179839536.70
Item- 4 Chapter-05 Reinforced cement concrete
5.0 REINFORCED CEMENT CONCRETE
5.9S FORM WORK
Centering and shuttering including strutting, propping
5.9
etc. and removal of form for
5.9.1 Foundations, footings, bases of columns, etc. for mass Sqm 2903 307.95 893978.85
1
concrete

TENDER DOCUMENT
5.9.2 Walls (any thickness) including attached pilasters, Sqm 2440 669.55 1633702
2
butteresses, plinth and string courses etc.
5.9.3 Suspended floors, roofs, landings, balconies and access Sqm 5165 766.55 3959230.75
3
platform
5.9.5 Lintels, beams, plinth beams, girders, bressumers and Sqm 1942 608.35 1181415.7
4
cantilevers
5 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 231 804.25 185781.75
6 5.9.7 Stairs, (excluding landings) except spiral-staircases Sqm 2109 657.75 1387194.75
Extra for additional height in centering, shuttering where
ever required with adequate bracing, propping etc.,
5.11 including cost of de-shuttering and decentering at all
levels, over a height of 3.5 m, for every additional height
of 1 metre or part thereof (Plan area to be measured).
5.11.1 Suspended floors, roofs, landing, beams and balconies Sqm 5265 319.25 1680851.25
7
(Plan area to be measured)
5.12S PRE-CAST RCC
5.15 Providing, hoisting and fixing above plinth level up to cum 46 12321.25 566777.5
floor five level precast reinforced cement concrete in
lintels, beams and bressumers, including setting in
cement mortar 1:3 (1 cement : 3 coarse sand), cost of
8 required centering and shuttering but , excluding the cost
of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) derived from natural sources : 3 graded
stone aggregate 20 mm nominal size derived from
natural sources)
Providing precast cement concrete Jali 1:2:4 (1 cement :
2 coarse sand(zone-III) : 4 graded stone aggregate 6mm
nominal size ), reinforced with 1.6 mm dia mild steel
5.18 wire, including centering and shuttering, roughening
cleaning, fixing and finishing in cement mortar 1:3 (1
cement: 3 fine sand) etc. complete, excluding plastering
of the jambs, sills and soffits.
9 5.18.1 50 mm thick Sqm 116 1580.9 183384.4
5.22S STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work including
5.22 straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or Kg 474680 89.65 42555062
10
more.
Steel reinforcement for R.C.C. work including
5.22A straightening, cutting, bending, placing in position and
binding all complete above plinth level.
5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or Kg 273960 89.65 24560514
11
more.
5.33S DESIGN MIX CONCRETE
Providing and laying in position ready mixed or site
batched design mix cement concrete for reinforced
cement concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland
Pozzolana / Ordinary Portland /Portland Slag cement,
admixtures in recommended proportions as per IS: 9103
to accelerate / retard setting of concrete, to improve
durability and workability without impairing strength;
including pumping of concrete to site of laying, curing,
5.33
carriage for all leads; but excluding the cost of centering,
shuttering, finishing and reinforcement as per direction of
the engineer-in-charge; for the following grades of
concrete. Note: Extra cement up to 10% of the minimum
specified cement content in design mix shall be payable
separately. In case the cement content in design mix is
more than 1.10 times of the specified minimum cement
content, the contractor shall have discretion to either re-
design the mix or bear the cost of extra cement.

TENDER DOCUMENT
5.33.1 All works upto plinth level

12
330 kg /cum
5.33.2 All works above plinth level upto floor V level
13
330 kg /cum
5.35 Add for using extra cement in the items of design mix Quintal 7564 688.45 5207435.8
14
over and above the specified cement content therein.
Total 115989927.35
Item- 5 Chapter-06 Masonry work
6.0 MASONRY WORK
Brick work with common burnt clay F.P.S. (non modular)
6.1
bricks of class designation 7.5 in foundation and plinth in:
1 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 3574 6882 24596268
2 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 4871 6658.25 32432335.75
Brick work with common burnt clay F.P.S. (non modular)
6.4 bricks of class designation 7.5 in superstructure above
plinth level up to floor V level in all shapes and sizes in :
6.12S HALF BRICK MASONRY
Half brick masonry with common burnt clay F.P.S. (non
6.13 modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level.
5 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 403 1018.05 410274.15
Total 90866381.25
Item- 6 Chapter-07 Stone work
7.0 STONE WORK
Stone tile work for wall lining upto 10 m height with
special adhesive over 12 mm thick bed of cement mortar
7.38 1:3 (1 cement : 3 coarse sand), including pointing in
white cement with an admixture of pigment to match the
stone shade.
7.38.1 8mm thick (mirror polished and machine cut edge)
1 7.38.1.1 Granite stone of any colour and shade Sqm 144 2675.7 385300.8
Total 385300.80
Item- 7 Chapter-8 - Cladding work
8.0 CLADDING WORK
Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills, facias
and similar locations of required size, approved shade,
8.2 colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated with
white cement, mixed with matching pigment, epoxy touch
ups, including rubbing, curing, moulding and polishing of
edges to give high gloss finish etc. complete at all levels.
8.2.2 Granite stone slab of colour black, Cherry/Ruby red
1 8.2.2.2 Area of slab over 0.50 sqm Sqm 50 4425.35 221267.5
Providing edge moulding to 18 mm thick marble stone
counters, Vanities etc., including machine polishing to
8.3
edge to give high gloss finish etc. complete as per
design approved by Engineer-in-Charge.
2 8.3.2 Granite work Metre 40 418.85 16754

TENDER DOCUMENT
8.5 Extra for providing opening of required size & shape for Each 14 808.15 11314.1
wash basin/ kitchen sink in kitchen platform, vanity
counter and similar location in marble/ Granite/ stone
3
work, including necessary holes for pillar taps etc.
including moulding, rubbing and polishing of cut edges
etc. complete.
8.20S STONE WORK DRY CLADDING
8.31 Providing and fixing Ist quality ceramic glazed wall tiles Sqm 659 1063.45 700813.55
conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades
except burgundy, bottle green, black of any size as
approved by Engineer-in-Charge, in skirting, risers of
4
steps and dados, over 12 mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) and jointing with
grey cement slurry @ 3.3kg per sqm, including pointing
in white cement mixed with pigment of matching shade
complete.
Total 950149.15
Item- 8 Chapter-9 - Wood and PVC work
9.0 WOOD AND P.V.C. WORK
Providing and fixing 25 mm thick shutters for cup board
9.16
etc. :
Providing and fixing Pre-laminated flat pressed 3 layer
(medium density) particle board or graded wood particle
board IS : 3087 marked, with one side decorative and
9.18 other side balancing lamination Grade I, Type II exterior
grade IS : 12823 marked, in shelves with screws and
fittings wherever required, edges to be painted with
polyurethane primer (fittings to be paid separately).
1 9.18.1 18 mm thick Sqm 26 1089.3 28321.8
2 9.18.2 25 mm thick Sqm 52 1501 78052
Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) non-decorative type,
core of block board construction with frame of 1st class
9.21
hard wood and well matched commercial 3 ply veneering
with vertical grains or cross bands and face veneers on
both faces of shutters:
9.21.1 35 mm thick including ISI marked Stainless Steel butt Sqm 314 2015.75 632945.5
3
hinges with necessary screws
9.21.2 30 mm thick including ISI marked Stainless Steel butt Sqm 106 1881.95 199486.7
4
hinges with necessary screws
9.21.3 25 mm thick (for cupboard) including ISI marked nickel Sqm 160 1830 292800
5 plated bright finished M.S. piano hinges with necessary
screws
9.23 Extra for providing lipping with 2nd class teak wood Sqm 420 401.4 168588
6 battens 25 mm minimum depth on all edges of flush door
shutters (over all area of door shutter to be measured).
Providing and fixing wire gauge shutters using
galvanized M.S. wire gauge of average width of aperture
9.27 1.4 mm in both directions with wire of dia 0.63 mm, for
doors, windows and clerestory windows with hinges and
necessary screws :
9.27.1 35 mm thick shutters
with ISI marked M.S. pressed butt hinges bright finished
9.27.1.1
of required size
7 9.27.1.1.1 Second class teak wood Sqm 129 4342.3 560156.7
9.40S MISCELLANEOUS-WOOD WORK
Providing and fixing nickel plated M.S. pipe curtain rods
9.47
with nickel plated brackets :
8 9.47.1 20 mm dia (heavy type) Metre 120 152.65 18318

TENDER DOCUMENT
Providing and fixing M.S. grills of required pattern in

frames of windows etc. with M.S. flats, square or round
9.48
bars etc. including priming coat with approved steel
primer all complete.
9 9.48.1 Fixed to steel windows by welding Kg 8250 181 1493250
9.88S CHROMIUM PLATED BRASS FITTINGS
Providing and fixing special quality chromium plated
9.90 brass cupboard locks with six levers of approved quality
including necessary screws etc. complete.
10 9.90.3 Size 65 mm Each 50 321.1 16055
ANODISED ALUMINIUM FITTINGS (ALL FITTINGS
9.95S
SHALL BE ISI MARKED)
Providing and fixing aluminium sliding door bolts, ISI
marked anodised (anodic coating not less than grade AC
9.96
10 as per IS : 1868), transparent or dyed to required
colour or shade, with nuts and screws etc. complete :
11 9.96.1 300x16 mm Each 136 260.3 35400.8
12 9.96.2 250x16 mm Each 56 234.9 13154.4
Providing and fixing aluminium tower bolts, ISI marked,
anodised (anodic coating not less than grade AC 10 as
9.97
per IS : 1868 ) transparent or dyed to required colour or
shade, with necessary screws etc. complete :
13 9.97.2 250x10 mm Each 144 104.4 15033.6
14 9.97.3 200x10 mm Each 192 90.8 17433.6
15 9.97.5 100x10 mm Each 56 58.65 3284.4
Providing and fixing aluminium handles, ISI marked,
anodised (anodic coating not less than grade AC 10 as
9.100
per IS : 1868) transparent or dyed to required colour or
shade, with necessary screws etc. complete :
16 9.100.1 125 mm Each 400 60.05 24020
17 9.100.2 100 mm Each 310 53.25 16507.5
Providing and fixing aluminium hanging floor door
stopper, ISI marked, anodised (anodic coating not less
9.101 than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade, with necessary screws etc.
complete.
18 9.101.2 Twin rubber stopper Each 144 62.25 8964
Total 3621772.00
Item- 9 Chapter-10 Steel work
10.0 STEEL WORK
10.1 Structural steel work in single section, fixed with or Kg 11000 93.05 1023550
without connecting plate, including cutting, hoisting, fixing
1
in position and applying a priming coat of approved steel
primer all complete.
10.2 Structural steel work riveted, bolted or welded in built up Kg 503261 111.95 56340068.95
sections, trusses and framed work, including cutting,
2
hoisting, fixing in position and applying a priming coat of
approved steel primer all complete.
10.4 Providing and fixing 1 mm thick M.S. sheet sliding- Sqm 13 5374.35 69866.55
shutters, with frame and diagonal braces of 40x40x6 mm
angle iron, 3 mm M.S. gusset plates at the junctions and
3
corners, 25 mm dia pulley, 40x40x6 mm angle and T-
iron guide at the top and bottom respectively, including
applying a priming coat of approved steel primer
Providing and fixing 1mm thick M.S. sheet door with
frame of 40x40x6 mm angle iron and 3 mm M.S. gusset
10.5 plates at the junctions and corners, all necessary fittings
complete, including applying a priming coat of approved
steel primer.

TENDER DOCUMENT
4 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces Sqm 91 4781.15 435084.65
Providing and fixing factory made ISI marked steel
glazed doors, windows and ventilators, side /top /centre
hung, with beading and all members such as F7D,F4B,
K11 B and K12 B etc. complete of standard rolled steel
sections, joints mitred and flash butt welded and sash
10.11
bars tenoned and riveted, including providing and fixing
of hinges, pivots, including priming coat of approved
steel primer, but excluding the cost of other fittings,
complete all as per approved design, (sectional weight of
only steel members shall be measured for payment).
10.11.1 Fixing with 15x3 mm lugs 10 cm long embedded in Kg 8600 175.65 1510590
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
5
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size)
Providing and fixing T-iron frames for doors, windows
and ventilators of mild steel Tee-sections, joints mitred
10.13 and welded, including fixing of necessary butt hinges and
screws and applying a priming coat of approved steel
primer.
10.13.1 Fixing with 15x3 mm lugs 10 cm long embedded in Kg 211 114.65 24191.15
cement concrete block 15x10x10 cm of C.C. 1:3:6 (1
6
Cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size).
Providing and fixing pressed steel door frames
conforming to IS: 4351, manufactured from commercial
mild steel sheet of 1.60 mm thickness, including hinges,
jamb, lock jamb, bead and if required angle threshold of
mild steel angle of section 50x25 mm, or base ties of
10.14 1.60 mm, pressed mild steel welded or rigidly fixed
together by mechanical means, including M.S. pressed
butt hinges 2.5 mm thick with mortar guards, lock strike-
plate and shock absorbers as specified and applying a
coat of approved steel primer after pre-treatment of the
surface as directed by Engineer-in-charge:
10.14.1 Profile B
7 10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb Metre 176 444.5 78232
10.14.3 Profile E
8 10.14.3.1 Fixing with adjustable lugs with split end tail to each jamb Metre 662 511.4 338546.8
Steel work in built up tubular (round, square or
rectangular hollow tubes etc.) trusses etc., including
10.16 cutting, hoisting, fixing in position and applying a priming
coat of approved steel primer, including welding and
bolted with special shaped washers etc. complete.
9 10.16.3 Electric resistance or induction butt welded tubes Kg 170000 140.85 23944500
10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm Each 144 185.95 26776.8
dia M.S. bar, bent to shape with hooked ends in R.C.C.
10 slabs or beams during laying, including painting the
exposed portion of loop, all as per standard design
complete.
10.19 Providing and fixing mild steel round holding down bolts Kg 4388 88.5 388338
11
with nuts and washer plates complete.
Steel work welded in built up sections/ framed work,
including cutting, hoisting, fixing in position and applying
10.25
a priming coat of approved steel primer using structural
steel etc. as required.
10.25.1 In stringers, treads, landings etc. of stair cases, including Kg 1200 102.25 122700
12
use of chequered plate wherever required, all complete
10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, Kg 13900 142.3 1977970
13
gates and similar works

TENDER DOCUMENT
Providing and fixing hand rail of approved size by

welding etc. to steel ladder railing, balcony railing,
10.26
staircase railing and similar works, including applying
priming coat of approved steel primer.
14 10.26.1 M.S. tube Kg 400 157.15 62860
10.28 Providing and fixing stainless steel ( Grade 304) railing Kg 9100 612.25 5571475
made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c
fixing the railing with necessary accessories & stainless
15
steel dash fasteners , stainless steel bolts etc., of
required size, on the top of the floor or the side of waist
slab with suitable arrangement as per approval of
Engineer-in-charge, (for payment purpose only weight of
stainless steel members shall be considered excluding
fixing accessories such as nuts, bolts, fasteners etc.).
Providing & fixing fly proof wire gauge to windows,
10.29 clerestory windows & doors with M.S. Flat 15x3 mm and
nuts & bolts complete.
10.29.1 Galvanised M.S. Wire gauge with 0.63 mm dia wire and Sqm 225 732.2 164745
16
1.4 mm aperture on both sides
Providing & fixing glass panes with putty and glazing
10.30 clips in steel doors, windows, clerestory windows, all
complete with :
10.30.2 5.5 mm thick glass panes (weight not less than 12.50 Sqm 49 1243.5 60931.5
17
kg/sqm)
Total 92140426.40
Item- 10 Chapter-11 -Flooring
11.0 FLOORING
11.2 Dry brick on edge flooring in required pattern with bricks Sqm 15866 733.3 11634537.8
of class designation 7.5 on a bed of 12 mm mud mortar,
1
including filling joints with local sand, with common burnt
clay non modular bricks.
Cement concrete flooring 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate) finished with a floating
11.3
coat of neat cement, including cement slurry, but
excluding the cost of nosing of steps etc. complete.
2 11.3.1 40 mm thick with 20 mm nominal size stone aggregate Sqm 448 545 244160
11.16S TILE FLOORING
Chequerred precast cement concrete tiles 22 mm thick
in footpath & courtyard, jointed with neat cement slurry
11.20 mixed with pigment to match the shade of tiles, including
rubbing and cleaning etc. complete, on 20 mm thick bed
of cement mortar 1:4 (1 cement: 4 coarse sand).
3 11.20.3 Dark shade pigment using ordinary cement Sqm 7075 983.95 6961446.25
Providing and fixing 10 mm thick acid and/or alkali
resistant tiles of approved make and colour using acid
11.21 and/or alkali resisting mortar bedding, and joints filled
with acid and/or alkali resisting cement as per IS : 4457,
complete as per the direction of Engineer-in- Charge.
In flooring on a bed of 10 mm thick mortar 1:4 (1 acid
11.21.1
proof cement : 4 coarse sand)
4 11.21.1.1 Acid and alkali resistant tile Sqm 312 1515.45 472820.4
In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof
11.21.2
cement : 4 coarse sand)
5 11.21.2.1 Acid and alkali resistant tile Sqm 351 1637.7 574832.7
11.26S KOTA STONE FLOORING

TENDER DOCUMENT
Kota stone slab flooring over 20 mm (average) thick

base laid over and jointed with grey cement slurry mixed
11.26 with pigment to match the shade of the slab, including
rubbing and polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) :
6 11.26.1 25 mm thick Sqm 2708 1706.6 4621472.8
11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, Sqm 216 2038.55 440326.8
dado and pillars laid on 12 mm (average) thick cement
mortar 1:3 (1 cement: 3 coarse sand) and jointed with
7
grey cement slurry mixed with pigment to match the
shade of the slabs, including rubbing and polishing
complete.
11.28S SAND STONE FLOORING
11.31 Extra for pre finished nosing in treads of steps of Kota Metre 1224 157.35 192596.4
8
stone/ sand stone slab.
11.37S CERAMIC GLAZED TILES
11.37 Providing and laying Ceramic glazed floor tiles of size Sqm 164 935.6 153438.4
300x300 mm (thickness to be specified by the
manufacturer) of 1st quality conforming to IS : 15622 of
approved make in colours such as White, Ivory, Grey,
9
Fume Red Brown, laid on 20 mm thick cement mortar
1:4 (1 Cement : 4 Coarse sand), Jointing with grey
cement slurry @ 3.3 kg/sqm including pointing the joints
with white cement and matching pigment etc., complete.
11.37A Providing and fixing 1st quality ceramic glazed floor tiles Sqm 32 938.5 30032
conforming to IS : 15622 (thickness to be specified by
the manufacturer ) of approved make in all colours,
shades except burgundy, bottle green, black of any size
as approved by Engineer-in-Charge in skirting, risers of
10
steps and dados over 12 mm thick bed of cement Mortar
1:3 (1 cement: 3 coarse sand) and jointing with grey
cement slurry @ 3.3kg per sqm including pointing in
white cement mixed with pigment of matching shade
complete.
11.41S VITRIFIED FLOOR TILES
Providing and laying Vitrified tiles in floor in different
sizes (thickness to be specified by the manufacturer)
with water absorption less than 0.08% and conforming to
IS:15622, of approved brand & manufacturer, in all
colours and shade, laid on 20 mm thick cement mortar
1:4 (1 cement: 4 coarse sand) jointing with grey cement
11.41A
slurry @3.3 kg/sqm including grouting the joints with
white cement and matching pigments etc. The tiles must
be cut with the zero chipping diamond cutter only .
Laying of tiles will be done with the notch trowel, plier,
wedge, clips of required thickness, leveling system and
rubber mallet for placing the tiles gently and easily.
11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size
11 11.41A.3.1 Size of Tile 600 x 600 mm Sqm 2736 1311.05 3587032.8
Providing and laying Vitrified tiles in different sizes
(thickness to be specified by manufacturer), with water
absorption less than 0.08 % and conforming to I.S.
15622, of approved make, in all colours & shade, in
11.46
skirting, riser of steps, over 12 mm thick bed of cement
mortar 1:3 (1 cement: 3 coarse sand), jointing with grey
cement slurry @ 3.3 kg/ sqm including grouting the joint
with white cement & matching pigments etc. complete.
12 11.46.2 Size of Tile 600x600 mm Sqm 251 1466.5 368091.5
Total 29280787.85
Item- 11 Chapter-12-Roofing
12.0 ROOFING

TENDER DOCUMENT
12.1S SHEET ROOFING

Providing gola 75x75 mm in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 stone aggregate 10 mm and
12.21
down gauge), including finishing with cement mortar 1:3
(1 cement : 3 fine sand) as per standard design :
1 12.21.1 In 75x75 mm deep chase Metre 1304 260.2 339300.8
12.22 Making khurras 45x45 cm with average minimum Each 124 266.6 33058.4
thickness of 5 cm cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate of 20 mm
2 nominal size) over P.V.C. sheet 1 m x1 m x 400 micron,
finished with 12 mm cement plaster 1:3 (1 cement : 3
coarse sand) and a coat of neat cement, rounding the
edges and making and finishing the outlet complete.
Providing, fixing and embedding sand cast iron
accessories for rain water pipes in the masonry
12.40 surrounded with 12 mm thick cement mortar of the same
mix, as that of masonry (lead caulking will be paid for
separately):
Providing and fixing on wall face unplasticised Rigid PVC
rain water pipes conforming to IS : 13592 Type A,
12.41 including jointing with seal ring conforming to IS : 5382,
leaving 10 mm gap for thermal expansion, (i) Single
socketed pipes.
3 12.41.2 110 mm diameter Metre 620 319.75 198245
Providing and fixing on wall face unplasticised - PVC
moulded fittings/ accessories for unplasticised Rigid PVC
12.42 rain water pipes conforming to IS : 13592 Type A,
including jointing with seal ring conforming to IS : 5382,
leaving 10 mm gap for thermal expansion.
12.42.1 Coupler
4 12.42.1.2 110 mm Each 124 119.95 14873.8
12.42.4 Single tee without door
5 12.42.4.2 110x110x110 mm Each 28 190.75 5341
12.42.5 Bend 87.5 degrees
6 12.42.5.2 110 mm bend Each 180 132 23760
12.42.6 Shoe (Plain)
7 12.42.6.2 110 mm Shoe Each 124 115.95 14377.8
Providing and fixing unplasticised -PVC pipe clips of
approved design to unplasticised - PVC rain water pipes
by means of 50x50x50 mm hard wood plugs, screwed
12.43
with M.S. screws of required length, including cutting
brick work and fixing in cement mortar 1:4 (1 cement : 4
coarse sand) and making good the wall etc. complete.
8 12.43.2 110 mm Each 372 309.5 115134
12.44 Providing and fixing to the inlet mouth of rain water pipe Each 124 47.9 5939.6
9 cast iron grating 15 cm diameter and weighing not less
than 440 grams.
12.50 Providing and fixing precoated galvanised iron profile Sqm 6732 671.55 4520874.6
sheets (size, shape and pitch of corrugation as approved
by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated
thickness with zinc coating 120 grams per sqm as per IS:
277, in 240 mpa steel grade, 5-7 microns epoxy primer
on both side of the sheet and polyester top coat 15-18
microns. Sheet should have protective guard film of 25
10 microns minimum to avoid scratches during
transportation and should be supplied in single length
upto 12 metre or as desired by Engineer-in-charge. The
sheet shall be fixed using self drilling /self tapping screws
of size (5.5x 55 mm) with EPDM seal, complete upto any
pitch in horizontal/ vertical or curved surfaces, excluding
the cost of purlins, rafters and trusses and including
cutting to size and shape wherever required.

TENDER DOCUMENT
Providing and fixing precoated galvanised steel sheet

roofing accessories 0.50 mm (+0.05 %) total coated
thickness, Zinc coating 120 grams per sqm as per IS:
12.51
277, in 240 mpa steel grade, 5-7 microns epoxy primer
on both side of the sheet and polyester top coat 15-18
microns using self drilling/ self tapping screws complete :
11 12.51.1 Ridges plain (500 - 600mm) Metre 722 450.6 325333.2
12 12.51.6 Gutter (600 mm over all girth) Metre 160 1110.6 177696
Total 5773934.20
Item- 12 Chapter-13-Finishing / Exterior Finishing
13.0 FINISHING
13.1S CEMENT PLASTER (IN FINE SAND)
13.1 12 mm cement plaster of mix :
1 13.1.1 1:4 (1 cement: 4 fine sand) Sqm 4897 294.85 1443880.45
2 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 8780 282 2475960
15 mm cement plaster on the rough side of single or half
13.2
brick wall of mix :
3 13.2.2 1:6 (1 cement: 6 fine sand) Sqm 6670 324.3 2163081
13.16S 6MM CEMENT PLASTER
13.16 6 mm cement plaster of mix :
4 13.16.1 1:3 (1 cement : 3 fine sand) Sqm 650 253.05 164482.5
5 13.18 Neat cement punning. Sqm 1110 67.8 75258
13.25 Extra for plastering:
13.26 Providing and applying plaster of paris putty of 2 mm Sqm 3480 214.3 745764
6 thickness over plastered surface to prepare the surface
even and smooth complete.
Distempering with oil bound washable distemper of
13.41 approved brand and manufacture to give an even shade
:
13.41.1 New work (two or more coats) over and including water Sqm 9380 162.55 1524719
7
thinnable priming coat with cement primer
13.44S EXTERIOR FINISHING
Finishing walls with water proofing cement paint of
13.44
required shade :
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 Sqm 22908 97.6 2235820.8
8
sqm)
Finishing with Deluxe Multi surface paint system for
13.48 interiors and exteriors using Primer as per
manufacturers specifications :
13.48.2 Painting wood work with Deluxe Multi Surface Paint of Sqm 1338 144.9 193876.2
required shade. Two or more coat applied @ 0.90 ltr/10
9
sqm over an under coat of primer applied @0.75 ltr/10
sqm of approved brand and manufacture
13.48.3 Painting Steel work with Deluxe Multi Surface Paint to Sqm 2170 140.05 303908.5
give an even shade. Two or more coat applied @ 0.90
10
ltr/10 sqm over an under coat of primer applied @ 0.80
ltr/10 sqm of approved brand and manufacture
Finishing with Epoxy paint (two or more coats) at all
locations prepared and applied as per manufacturer's
13.52
specifications including appropriate priming coat,
preparation of surface, etc. complete.
11 13.52.2 On concrete work Sqm 4894 198.4 970969.6
Painting with synthetic enamel paint of approved brand
13.61
and manufacture to give an even shade :
12 13.61.1 Two or more coats on new work Sqm 492 131.45 64673.4
Painting with aluminium paint of approved brand and
13.63
manufacture to give an even shade .
13 13.63.1 Two or more coats on new work Sqm 13994 121.45 1699571.3
Pa g e 2 0 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

TENDER DOCUMENT
13.71 per 25000 5.05 126250

Lettering with black Japan paint of approved brand and letter
14
manufacture per cm
height
13.80 Providing and applying white cement based putty of Sqm 4320 123.85 535032
average thickness 1 mm, of approved brand and
15
manufacturer, over the plastered wall surface to prepare
the surface even and smooth complete.
Total 14723246.75
Item- 13 Chapter-15- Dismantling
15.0 DISMANTLING AND DEMOLISHING
Demolishing cement concrete manually/ by mechanical
15.2 means including disposal of material within 50 metres
lead as per direction of Engineer - in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent cum 3759 2007.1 7544688.9
1
design mix)
Demolishing brick work manually/ by mechanical means
including stacking of serviceable material and disposal of
15.7
unserviceable material within 50 metres lead as per
direction of Engineer-in-charge.
2 15.7.4 In cement mortar cum 2840 1698.45 4823598
15.18 Dismantling steel work in built up sections in angles, Kg 6000 4.65 27900
tees, flats and channels including all gusset plates, bolts,
3
nuts, cutting rivets, welding etc. including dismembering
and stacking within 50 metres lead.
15.19 Dismantling steel work manually/ by mechanical means Kg 26500 3.2 84800
in built up sections without dismembering and stacking
4
within 50 metres lead as per direction of Engineer-in-
charge.
15.29 Dismantling stone slab roofing over wooden karries or cum 24 2197.55 52741.2
R.C.C. battens (dismantling karries and battens to be
5 paid for separately), including stacking of serviceable
material and disposal of unserviceable material within 50
metres lead.
15.58 Demolishing R.C.C. work by mechanical means and cum 705 2328.55 1641627.75
stockpiling at designated locations and disposal of
6 dismantled materials up to a lead of 1 kilometre, stacking
serviceable and unserviceable material separately
including cutting reinforcement bars.
15.60 Disposal of building rubbish / malba / similar cum 1000 219.35 219350
unserviceable, dismantled or waste materials by
mechanical means, including loading, transporting,
7
unloading to approved municipal dumping ground or as
approved by Engineer-in-charge, beyond 50 m initial
lead, for all leads including all lifts involved.
Total 14394705.85
Item- 14 Chapter-16-Road Work/ Roads
16.0 ROAD WORK
16.1S ROADS
16.1 Preparation and consolidation of sub grade with power Sqm 6190 180.5 1117295
road roller of 8 to 12 tonne capacity after excavating
earth to an average of 22.5 cm depth, dressing to
1 camber and consolidating with road roller including
making good the undulations etc. and re-rolling the sub
grade and disposal of surplus earthwith lead upto 50
metres.
16.3 Supplying and stacking at site.
2 16.3.1 90 mm to 45 mm size stone aggregate cum 2294 1937.6 4444854.4

TENDER DOCUMENT
3 16.3.2 63 mm to 45 mm size stone aggregate cum 3039 1624.5 4936855.5

4 16.3.10 Moorum cum 2084 888.3 1851217.2
16.4 Laying, spreading and compacting stone aggregate of cum 5333 865.8 4617311.4
specified sizes to WBM specifications in uniform
thickness, hand picking, rolling with 3 wheeled
road/vibratory roller 8-10 tonne capacity in stages to
5
proper grade and camber, applying and brooming
requisite type of screening / binding material to fill up
interstices of coarse aggregate, watering and
compacting to the required density .
Supplying, stacking and Spreading 6 mm thick red bajri,
16.6 watering and rolling complete including preparation of
the surface and rolling.
6 16.6.1 With road roller/ hand roller Sqm 4420 21.8 96356
16.15S FENCING
16.20 Welded steel wire fabric fencing with posts of specified Sqm 481 55 26455
material and of standard design placed and embedded
in cement concrete blocks 45x45x 60 cm of mix 1:5:10 (1
cement:5 fine sand : 10 graded stone aggregate 40 mm
nominal size), every 15th post, last but one end post and
corner post shall be strutted on both sides and end post
7 on one side only and struts embedded in cement
concrete blocks 70x45x50 cm of the same mix, provided
with welded steel wire fabric fixed between the posts
fitted and fixed with G.I. staples on wooden plugs or tied
to 6 mm bar nibs with G.I. binding wire (cost of posts,
welded steel wire fabric, painting, earth work in
excavation and concrete to be paid for separately).
16.25S SURFACE DRESSING
Surface dressing one coat on new surface with bitumen
of specified grade at a rate of 1.95 kg/sqm of surface
16.28 area with 1.5 cum of stone chippings 13.2 mm nominal
size per 100 sqm of road surface, including consolidation
with road roller of 6 to 8 tonne capacity , etc. complete :
16.28.1 Using bitumen emulsion (minimum 50% bitumen Sqm 4225 169.8 717405
8
content- RS grade conforming to IS : 8887)
Providing and applying tack coat using bitumen emulsion
conforming to IS:8887, using emulsion pressure
16.31
distributer including preparing the surface & cleaning
with mechanical broom.
16.31.1 With rapid setting bitumen emulsion
9 16.31.1.1 On W.B.M / W.M.M. @ 0.4kg/sqm Sqm 4225 11.6 49010
10 16.31.1.2 On bituminous surface @ 0.25kg/sqm Sqm 3900 7.9 30810
2.5 cm premix carpet surfacing with 2.25 cum and 1.12
cum of stone chippings of 13.2 mm and 11.2 mm size
respectively per 100 sqm and 52 kg and 56 kg of hot
bitumen per cum of stone chippings of 13.2 mm and
16.33
11.2 mm size respectively, including a tack coat with hot
straight run bitumen, including consolidation with road
roller of 6 to 9 tonne capacity etc. complete (tack coat to
be paid for separately).
16.33.1 With paving Asphalt grade VG - 10 heated and then Sqm 8125 227 1844375
11 mixed with solvent at the rate of 70 grams per kg of
asphalt
2.5 cm thick bitumastic sheet with hot bitumen of
approved quality, using stone chippings (60% with 12.5
mm nominal size and 40% with 10 mm nominal size) @
1.65 cum per 100 sqm and coarse sand @ 1.65 cum per
16.38 100 sqm of road surface and with bitumen @ 56 kg/cum
of stone chippings and @ 128 kg/cum of sand over a
tack coat with hot straight run bitumen, including
consolidation with road roller of 8 to 10 tonne etc.
complete. (tack coat to be paid separately) :

TENDER DOCUMENT
16.38.1 With paving Asphalt grade VG - 10 heated and then Sqm 8125 285 2315625
12 mixed with solvent at the rate of 70 grams per kg of
asphalt
16.40S SEAL COAT
16.40 Providing and laying seal coat of premixed fine Sqm 8125 79.85 648781.25
aggregate ( passing 2.36 mm and retained on 180
micron sieve) with bitumen using 128 kg of bitumen of
13 grade VG - 10 bitumen per cum of fine aggregate and
0.60 cum of fine aggregate per 100 sqm of road surface,
including rolling and finishing with road roller all
complete.
16.42S CONCRETE PAVEMENTS
16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 cum 2562 7399.2 18956750.4
graded stone aggregate 40 mm nominal size) in
14 pavements, laid to required slope and camber in panels
as required including consolidation finishing and tamping
complete.
Providing and laying design mix cement concrete of M-
30 grade, in roads/ taxi tracks/ runways, using cement
content as per design mix, using coarse sand and
graded stone aggregate of 40 mm nominal size in
appropriate proportions as per approved & specified
design criteria, providing dowel bars with sleeve/ tie bars
wherever required, laying at site, spreading and
compacting mechanically by using needle and surface
16.43 vibrators, levelling to required slope/ camber, finishing
with required texture, including steel form work with
sturdy M.S. channel sections, curing, making provision
for contraction/ expansion, construction & longitudinal
joints (10 mm wide x 50 mm deep) by groove cutting
machine, providing and filling joints with approved joint
filler and sealants, complete all as per direction of
Engineer-in-charge (Item of joint fillers, sealants, dowel
bars with sleeve/ tie bars to be paid separately).
15 16.43.1 Cement concrete prepared with batch mixing machine cum 1030 9492.9 9777687
Providing and filling in position rubberized bitumen hot
sealing compound for sealing of expansion joints in
16.46
roads / pavements all complete as per direction of the
Engineer-in-Charge.
16.46.1 per cm 41805 7.5 313537.5
depth
per cm
Using grade 'A' sealing compound conforming to IS:
16 width
1834.
per
metre
length
16.49S MISCELLANEOUS
16.62 Providing and applying 2.5 mm thick road marking strips Sqm 208 623.8 129750.4
(retro- reflective) of specified shade/ colour using hot
thermoplastic material by fully/ semi automatic
thermoplastic paint applicator machine fitted with profile
shoe, glass beads dispenser, propane tank heater and
17 profile shoe heater, driven by experienced operator on
road surface including cost of material, labour, T&P,
cleaning the road surface of all dirt, seals, oil, grease
and foreign material etc. complete as per direction of
Engineer-in-charge and accordance with applicable
specifications.

TENDER DOCUMENT
16.69 Providing and laying at or near ground level factory cum 77 8613.55 663243.35
made kerb stone of M-25 grade cement concrete in
position to the required line, level and curvature, jointed
with cement mortar 1:3 (1 cement: 3 coarse sand),
including making joints with or without grooves (thickness
18 of joints except at sharp curve shall not to more than
5mm), including making drainage opening wherever
required complete etc. as per direction of Engineer-in-
charge (length of finished kerb edging shall be measured
for payment). (Precast C.C. kerb stone shall be
approved by Engineer-in-charge).
16.75 Providing and laying C.C. pavement of mix M-25 with cum 2831 8277.55 23433744.05
ready mixed concrete from batching plant. The ready
mixed concrete shall be laid and finished with screed
board vibrator , vacuum dewatering process and finally
finished by floating, brooming with wire brush etc.
19
complete as per specifications and directions of
Engineer-in-charge. (The panel shuttering work shall be
paid for separately). (Note:- Cement content considered
in this item is @ 330 kg/cum. Excess/less cement used
as per design mix is payable/ recoverable separately).
Providing and laying factory made chamfered edge
Cement Concrete paver blocks in footpath, parks, lawns,
drive ways or light traffic parking etc, of required
strength, thickness & size/ shape, made by table
vibratory method using PU mould, laid in required colour
& pattern over 50mm thick compacted bed of sand,
16.91 compacting and proper embedding/laying of inter locking
paver blocks into the sand bedding layer through
vibratory compaction by using plate vibrator, filling the
joints with sand and cutting of paver blocks as per
required size and pattern, finishing and sweeping extra
sand. complete all as per direction of Engineer-in-
Charge.
16.91.2 80 mm thick C.C. paver block of M-30 grade with Sqm 1120 1011.2 1132544
20
approved color design and pattern.
Total 77103607.45
Item- 15 Chapter-17- Sanitary Installations
17.0 SANITARY INSTALLATIONS
Providing and fixing water closet squatting pan (Indian
type W.C. pan ) with 100 mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing cistern, including
17.1 flush pipe, with manually controlled device (handle lever)
conforming to IS : 7231, with all fittings and fixtures
complete, including cutting and making good the walls
and floors wherever required:
17.1.1 White Vitreous china Orissa pattern W.C. pan of size Each 34 5781.35 196565.9
1
580x440 mm with integral type foot rests
Providing and fixing white vitreous china pedestal type
water closet (European type W.C. pan) with seat and lid,
10 litre low level white P.V.C. flushing cistern, including
17.2 flush pipe, with manually controlled device (handle
lever), conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the
walls and floors wherever required :
2 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 16 5540.55 88648.8
Providing and fixing wash basin with C.I. brackets, 15
mm C.P. brass pillar taps, 32 mm C.P. brass waste of
17.7 standard pattern, including painting of fittings and
brackets, cutting and making good the walls wherever
require:
17.7.1 White Vitreous China Wash basin size 630x450 mm with Each 16 2275 36400
3
a pair of 15 mm C.P. brass pillar taps

TENDER DOCUMENT
17.7.4 White Vitreous China Flat back wash basin size 550x Each 21 1679.6 35271.6
4
400 mm with single 15 mm C.P. brass pillar tap
17.7B Providing and fixing wash basin with C.I. brackets, 15 Each 7 1404 9828
mm PTMT pillar cock, 32 mm PTMT waste coupling of
standard pattern, including painting of fittings and
5
brackets, cutting and making good the walls wherever
required. White Vitreous China Flat back wash basin size
550x400 mm with single 15 mm PTMT pillar cock.
17.8 Providing and fixing white vitreous china pedestal for Each 2 1500.05 3000.1
6 wash basin completely recessed at the back for the
reception of pipes and fittings.
Providing and fixing Stainless Steel A ISI 304 (18/8)
kitchen sink as per IS:13983 with C.I. brackets and
17.10 stainless steel plug 40 mm, including painting of fittings
and brackets, cutting and making good the walls
wherever required :
17.10.2 Kitchen sink without drain board
7 17.10.2.2 610x460 mm bowl depth 200 mm Each 1 3337.85 3337.85
17.23 Providing and fixing white vitreous china flat back or wall Each 12 1382.3 16587.6
8 corner type lipped front urinal basin of 430x260x350 mm
or 340x410x265 mm sizes respectively.
Providing and fixing P.V.C. waste pipe for sink or wash
17.28
basin including P.V.C. waste fittings complete.
17.28.2 Flexible pipe
9 17.28.2.1 32 mm dia Each 57 104.35 5947.95
17.29 Providing and fixing 100 mm sand cast Iron grating for Each 57 45.25 2579.25
10
gully trap.
17.31 Providing and fixing 600x450 mm beveled edge mirror of Each 13 1411.15 18344.95
superior glass (of approved quality) complete with 6 mm
11
thick hard board ground fixed to wooden cleats with C.P.
brass screws and washers complete.
17.71 Providing and fixing PTMT liquid soap container 109 mm Each 13 146.3 1901.9
wide, 125 mm high and 112 mm distance from wall of
12 standard shape with bracket of the same materials with
snap fittings of approved quality and colour, weighing not
less than 105 gms.
17.72 Providing and fixing PTMT towel ring trapezoidal shape Each 13 204.7 2661.1
215 mm long, 200 mm wide with minimum distances of
13 37 mm from wall face with concealed fittings
arrangement of approved quality and colour, weighing
not less than 88 gms.
Providing and fixing PTMT towel rail complete with
brackets fixed to wooden cleats with CP brass screws
17.73
with concealed fittings arrangement of approved quality
and colour.
17.73.2 600 mm long towel rail with total length of 645 mm, width Each 13 600.35 7804.55
14 78 mm and effective height of 88 mm, weighing not less
than 190 gms.
Total 428879.55
Item- 16 Chapter-18-Water Supply
18.0 WATER SUPPLY
18.7S C.P.V.C. PIPES

TENDER DOCUMENT
Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass threaded
fittings, i/c fixing the pipe with clamps at 1.00 m spacing.
This includes jointing of pipes & fittings with one step
18.8
CPVC solvent cement and the cost of cutting chases and
making good the same including testing of joints
complete as per direction of Engineer in Charge,
Concealed work, including cutting chases and making
good the wall etc.
1 18.8.1 15 mm nominal dia Pipes Metre 600 441.15 264690
3 18.8.3 25 mm nominal dia Pipes Metre 134 626.05 83890.7
Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply including all CPVC plain & brass threaded
18.9 fittings This includes jointing of pipes & fittings with one
step CPVC solvent cement, trenching, refilling & testing
of joints complete as per direction of Engineer in
Charge.-External work
18.15S BRASS FITTINGS
18.16 Providing and fixing brass stop cock of approved quality :
8 18.16.2 20 mm nominal bore Each 24 327.95 7870.8
Providing and fixing gun metal gate valve with C.I. wheel
18.17
of approved quality (screwed end) :
10 18.17.2 32 mm nominal bore. Each 5 589.9 2949.5
Providing and fixing ball valve (brass) of approved
18.18 quality, High or low pressure, with plastic floats complete
:
Providing and fixing uplasticised PVC connection pipe
18.21
with brass unions :
18.21.1 30 cm length
14 18.21.1.1 15 mm nominal bore Each 40 74.8 2992
Providing and fixing C.P. brass shower rose with 15 or
18.22
20 mm inlet :
15 18.22.1 100 mm diameter Each 2 166.35 332.7
18.31S C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES
18.48 Providing and placing on terrace (at all floor levels) Litre 24000 9.7 232800
polyethylene water storage tank, IS : 12701 marked, with
16 cover and suitable locking arrangement and making
necessary holes for inlet, outlet and overflow pipes but
without fittings and the base support for tank.
18.49S C.P. BRASS FITTINGS
Providing and fixing C.P. brass bib cock of approved
18.49
quality conforming to IS:8931 :
Providing and fixing C.P. brass long nose bib cock of
18.50 approved quality conforming to IS standards and
weighing not less than 810 gms.

TENDER DOCUMENT
Providing and fixing C.P. brass stop cock (concealed) of

18.52 standard design and of approved make conforming to
IS:8931.
Providing and fixing C.P. brass angle valve for basin
18.53 mixer and geyser points of approved quality conforming
to IS:8931
20 18.53.1 15mm nominal bore Each 76 500.35 38026.6
18.54S PTMT FITTINGS
Providing and fixing PTMT, push cock of approved
18.57
quality and colour.
18.57.1 15 mm nominal bore, 98 mm long, weighing not less Each 80 96.45 7716
21
than 75 gms
Total 3510729.35
Item- 17 Chapter-19 - Drainage / Stone ware pipes and fittings
19.0 DRAINAGE
19.1S STONE WARE PIPES AND FITTINGS
Providing, laying and jointing glazed stoneware pipes
class SP-1 with stiff mixture of cement mortar in the
19.1
proportion of 1:1 (1 cement : 1 fine sand) including
testing of joints etc. complete :
Providing and laying cement concrete 1:5:10 (1 cement :
5 coarse sand : 10 graded stone aggregate 40 mm
19.2
nominal size) all-round S.W. pipes including bed
concrete as per standard design :
3 19.2.1 100 mm diameter S.W. pipe Metre 190 895.5 170145
4 19.2.2 150 mm diameter S.W. pipe Metre 260 1095.15 284739
Providing and fixing square-mouth S.W. gully trap class
SP-1 complete with C.I. grating brick masonry chamber
with water tight C.I. cover with frame of 300 x300 mm
19.4
size (inside) the weight of cover to be not less than 4.50
kg and frame to be not less than 2.70 kg as per standard
design:
Providing and laying non-pressure NP2 class (light duty)
R.C.C. pipes with collars jointed with stiff mixture of
19.6
cement mortar in the proportion of 1:2 (1 cement : 2 fine
sand) including testing of joints etc. complete :
5 19.6.4 300 mm dia. R.C.C. pipe Metre 42 902.05 37886.1
Constructing brick masonry manhole in cement mortar
1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with
1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3
graded stone aggregate 20 mm nominal size),
foundation concrete 1:4:8 mix (1 cement : 4 coarse sand
(Zone-III) : 8 graded stone aggregate 40 mm nominal
19.7
size), inside plastering 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished with floating coat
of neat cement and making channels in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) finished with a floating
coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I.
cover with frame (light duty) 455x610 mm internal
19.7.1 dimensions, total weight of cover and frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) :
19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of Each 40 11687.1 467484
6
class designation 7.5

TENDER DOCUMENT
Extra for depth beyond 45 cm of brick masonry chamber

19.31
:
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x
45 cm dry brick honey comb shaft with bricks and S.W.
19.32
drain pipe 100 mm diameter, 1.8 m long complete as per
standard design.
19.32.1 With common burnt clay F.P.S. (non modular) bricks of Each 26 28029.15 728757.9
7
class designation 7.5
Providing and laying Non Pressure NP-3 class (Medium
duty) R.C.C. pipes including collars/spigot jointed with
19.35 stiff mixture of cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of joints etc.
complete
8 19.35.1 450 mm dia RCC pipes. Metre 70 2385.5 166985
9 19.35.2 600 mm dia RCC pipes. Metre 10 3051.55 30515.5
Providing and laying Non Pressure NP-4 class (Heavy
duty) R.C.C. pipes including collars/spigot jointed with
19.36 stiff mixture of cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of joints etc.
complete
10 19.36.2 600 mm dia RCC pipes. Metre 10 3519.85 35198.5
Total 2143110.00
Item- 18 Chapter-21-Aluminium work
21.0 ALUMINIUM WORK
Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other
sections of approved make conforming to IS: 733 and IS:
1285, fixing with dash fasteners of required dia and size,
including necessary filling up the gaps at junctions, i.e. at
top, bottom and sides with required EPDM rubber/
21.1 neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-
charge. (Glazing, paneling and dash fasteners to be paid
for separately) :
For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making provision
21.1.2 for fixing of fittings wherever required including the cost
of EPDM rubber / neoprene gasket required (Fittings
shall be paid for separately)
21.1.2.1 Anodised aluminium (anodised transparent or dyed to Kg 560 531.8 297808
1 required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
Total 297808.00
Item- 19 Chapter-22- Water Proofing
22.0 WATER PROOFING
22.14 Grading roof for water proofing treatment with
22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 cum 417 7510.75 3131982.75
1
graded stone aggregate 20mm nominal size)
Total 3131982.75
Item- 20 Chapter-23- Rain Water Harvesting & Tubewells
23.0 RAIN WATER HARVESTING & TUBEWELLS

TENDER DOCUMENT
Boring/drilling bore well of required dia for casing/

strainer pipe, by suitable method prescribed in IS: 2800
(part I), including collecting samples from different strata,
preparing and submitting strata chart/ bore log, including
23.1
hire & running charges of all equipments, tools, plants &
machineries required for the job, all complete as per
direction of Engineer-in-charge, upto 90 metre depth
below ground level.
23.1.1 All types of soil
1 23.1.1.1 300 mm dia Metre 360 592.05 213138
23.1.2 Rocky strata including Boulders
2 23.1.2.1 300 mm dia Metre 100 1416.3 141630
Boring/drilling bore well of required dia for casing/
strainer pipe, by suitable method prescribed in IS: 2800
(part I), including collecting samples from different strata,
preparing and submitting strata chart/ bore log, including
23.2
hire & running charges of all equipments, tools, plants &
machineries required for the job, all complete as per
direction of Engineer -in-charge, beyond 90 metre & upto
150 metre depth below ground level.
Supplying, assembling, lowering and fixing in vertical
position in bore well, ERW (Electric Resistance Welded)
FE 410 mild steel screwed and socketed/plain ended
casing pipes of required dia, conforming to IS: 4270, of
23.10 reputed & approved make, including painted with outside
surface with two coats of anticorrosive paint of approved
brand and manufacture, including required hire & labour
charges, fittings & accessories, all complete, for all
depths, as per direction of Engineer-in-charge.
23.10.3 200 mm nominal size dia having minimum wall thickness Metre 360 2082.1 749556
3
5.40 mm
Providing and fixing M.S. clamp of required dia to the top
of casing/ housing pipe of tubewell as per IS: 2800 (part
23.14
I), including necessary bolts & nuts of required size
complete.
4 23.14.3 200 mm clamp Each 16 1827 29232
Total 1133556.00
Item- 21 Chapter-26-NEW TECHNOLOGIES AND MATERIALS
26.0 NEW TECHNOLOGIES AND MATERIALS
26.28S REPAIR AND REHABILITATION ITEMS
Providing and injecting approved grout in proportion
recommended by the manufacturer into cracks/honey-
26.35 comb area of concrete/masonry by suitable gun/pump at
required pressure including cutting of nipples after curing
etc. complete as per directions of Engineer-in-Charge.
26.35.3 Epoxy injection grout in concrete/RCC work of approved Kg 3470 793.25 2752577.5
1
make
Total 2752577.50
4. ELIGIBILITY CONDITIONS
Important : All documents uploaded and remarks / confirmation entered by the bidders against any eligibility condition
shall be opened as part of technical bid only
Special Financial Criteria
S.No. Description Confirmation Remarks Documents

Required Allowed Uploading

TENDER DOCUMENT
Financial Eligibility Criteria: The tenderer must have minimum average annual
contractual turnover of V/N or "V" whichever is less crores; where V= Advertised value
of the tender in crores of Rupees N= Number of years prescribed for completion of work
for which bids have been invited. The average annual contractual turnover shall be
calculated as an average of "total contractual payments" in the previous three financial
Allowed
1 years, as per the audited balance sheet. However, in case balance sheet of the previous No No
(Mandatory)
year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year
shall be considered for calculating average annual contractual turnover. The tenderers
shall submit requisite information as per Annexure-VIII, along with copies of Audited
Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered
Accountant duly supported by Audited Balance Sheet.
Special Technical Criteria

(a)The tenderer must have successfully completed/substentially completed any of the
following during last 07 (seven) years, ending last day of month previous to the one in
which tender is invited: (i)Three similar works each costing not less than the amount
equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not
less than the amount equal to 40% of advertised value of the tender, or (iii) One similar
work each costing not less than the amount equal to 60% of advertised value of the
tender. (b) (i) In case of composite works (e.g. works involving more than one distinct
component, such as Civil Engineering works, S&T works, Electrical works, OHE works
etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must
have successfully completed/substantially completed any of the following during last 07
(seven) years, ending last day of month previous to the one in which tender is invited:
Three similar works each costing not less than the amount equal to 30% of advertised
Allowed
1 value of each component of tender, or Two similar works , each costing not less than the No No
(Mandatory)
amount equal to 40% of advertised value of each component of tender, ora One similar
work, each costing not less than the amount equal to 60% of advertised value of each
component of tender. Note: Separate completed works of minimum required values for
each component can also be considered for fulfillment of technical eligibility criteria. (b)
(ii) In such cases, what constitutes a component in a composite work shall be clearly
pre-defined with estimated tender cost of it, as part of the tender documents without any
ambiguity. Any work or set of works shall be considered to be a separate component,
only when cost of the component is more than Rs. 2 crore each. The tenderer shall
submit the completion certificate as per proforma given in annexure-IV-A or IV-B or IV-C
as applicable or in the format containing all information as required as per the Annex. IV-
A or IV-B or IV-C. Note :- Criteria for the completed work/Substantially completed has
been given in the General instructions in the tender document.
Definition of similar nature of work is " Civil/composite work involving construction of
1.1 No No Not Allowed
formation (cutting/filling/blanketing and or construction of bridges".
Bidders shall confirm and certify on the behalf of the tenderer including its constituents as under:
S.No. Description
1 I/we the tenderer (s) am/are signing this document after carefully reading the contents.
2 I/We the tenderer(s) also accept all the conditions of the tender and have signed all the pages in confirmation thereof.
I/we hereby declare that I/we have downloaded the tender documents from Indian Railway website www.ireps.gov.in . I/we have
verified the content of the document from the website and there is no addition, no deletion or no alteration to the content of the
3
tender document. In case of any discrepancy noticed at any stage i.e. evaluation of tenders, execution of work or final payment
of the contract, the master copy available with the railway Administration shall be final and binding upon me/us.
I/we declare and certify that I/we have not made any misleading or false representation in the forms, statements and
4
attachments in proof of the qualification requirements.
I/We also understand that my/our offer will be evaluated based on the documents/credentials submitted along with the offer and
5
same shall be binding upon me/us.
I/We declare that the information and documents submitted along with the tender by me/us are correct and I/we are fully
6
responsible for the correctness of the information and documents, submitted by us.
I/we certify that I/we the tenderer(s) is/are not blacklisted or debarred by Railways or any other Ministry / Department of Govt.
7 of India from participation in tender on the date of submission of bids, either in individual capacity or as a HUF/ member of the
partnership firm/LLP/JV/Society/Trust.
I/we understand that if the contents of the certificate submitted by us are found to be forged/false at any time during process for
evaluation of tenders, it shall lead to forfeiture of the Bid Security and may also lead to any other action provided in the contract
8
including banning of business for a period of upto two year. Further, I/we and all my/our constituents understand that my/our
offer shall be summarily rejected.

TENDER DOCUMENT
I/we also understand that if the contents of the certificate submitted by us are found to be false/forged at any time after the
award of the contract, it will lead to termination of the contract, along with forfeiture of Bid Security/Security Deposit and
9
Performance guarantee and may also lead to any other action provided in the contract including banning of business for a
period of upto two year.
I/We have read the clause regarding restriction on procurement from a bidder of a country which shares a land border with India
and certify that I am/We are not from such a country or, if from such a country, have been registered with the competent
10
Authority. I/We hereby certify that I/we fulfil all the requirements in this regard and am/are eligible to be considered (evidence of
valid registration by the competent authority is enclosed)
Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.
S.No. Description
Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. Please
submit a certificate in the prescribed format (please download the format from the link given below). Non submission of the
1 certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to
summary rejection of your offer.
( Click here to download the Format of Self Certification)
5. COMPLIANCE
Important : All documents uploaded and remarks / confirmation entered by the bidders against any compliance
condition shall be opened as part of technical bid only.
Commercial-Compliance

Mandatory in case Bid security amount is prescribed in STD Para 5.1.2 - The
Bid Security shall be deposited in cash through e-payment gateway or
submitted as Bank Guarantee bond from a scheduled commercial bank of Allowed
1 No No
India or as mentioned in tender documents. The Bank Guarantee bond shall (Mandatory)
be as per Annexure-XXXII and shall be valid for a period of 90days beyond the
bid validity period.
In case the tenderer is (i)Any firm recognized by Department of Industrial
Policy and Promotion (DIPP) as 'Startups' - shall be exempted from payment Allowed
2 Yes Yes
of Bid security deposit and shall submit certified copy of the registration/ Valid (Optional)
document issued by DIPP (mandatory if applicable)
In case the tenderer is (iii) Labour Cooperative Societies - shall deposit only
50% of the Earnest Money Deposit and shall submit certified copy of the Allowed
3 Yes Yes
registration/ Valid document issued by the relevant Ministry/ Labour (Optional)
commission (mandatory if applicable).
Please enter the percentage of local content in the material being offered.
Please enter 0 for fully imported items, and 100 for fully indigenous items. The Allowed
4 No Yes
definition and calculation of local content shall be in accordance with the Make (Optional)
in India policy as incorporated in the tender conditions.
Special Conditions

The initial e-Reverse Auction ( e-RA) period as mentioed in the Clause no.
26.1 (b), Annexure C, Para 2 of the "GENERAL INSTRUCTIONS" of Tender
1 Document will be as per railway board guidelines or as approved by Tender No No Not Allowed
accepting authority . (Applicable to the works and service tenders of value
more than Rs. 50 crore.)
The auto extension period as mentioed in the Clause no. 26..1(b), Annexure
C, Para 2 of the "GENERAL INSTRUCTIONS" of Tender Document will be as
2 No No Not Allowed
per railway board guidelines or as approved by Tender accepting authority .
(Applicable to the works and service tenders of value more than Rs. 50 crore.)
The Minimum Increment as mentioed in the Clause no. 26.1 (b), Annexure C,
Para 2 of the "GENERAL INSTRUCTIONS" of Tender Document will be as per
3 No No Not Allowed
railway board guidelines or as approved by Tender accepting authority .
(Applicable to the works and service tenders of value more than Rs.50 crore.)
Technical-Compliances

TENDER DOCUMENT

The tenderer shall submit the Firms's detail as per Annexure I. (Mandatory for Allowed
1 Yes Yes
all firms) (Mandatory)
The tenderer shall submit the copy of certificate as per proforma given in Allowed
2 Yes Yes
Annexure II. & IIA(Mandatory for all firms) (Mandatory)
TThe tenderer should submit the List of similar nature of works physically
completed/substantially completed in all respects during last 7 years , ending
last day of month previous to one in which tender is invited,(i) directly awarded
by Govt./Semi Govt./Public sector undertaking / Autonomous bodies /Municipal
bodies/ Railways Siding owners (ii) Public listed company having average
annual turnover of Rs. 500 crore and above in last 3 financial years excluding
the current financial year, listed on National Stock Exchange or Bombay Stock
Allowed
3 Exchange, incorporated/registered at least 5 years prior to the date of closing Yes Yes
(Optional)
of tender/ as per proforma given in Annexure-III. In case of JV firm, these
details are also required for all the members of the JV firm. In case, the
Secondary Component(s) has/ have been defined, the details of successfully
completed works of similar nature (that defined for the Secondary
Component), executed by tenderer himself / the subcontractor (fully by any
one or jointly i.e. partly by tenderer and remaining through subcontractor)
during last five years, shall also be submitted (for five years )
In case of composite work, having distinct components and having separate
schedule for each component having value more than 2 crores, tenderer
should submit a details of work of similar nature successfully
completed/substantially completed during last 7 years , ending last day of
month previous to the one in which tender invited and detailed in Annexure-III
(Bifurcated as per components of tender schedule), as per proforma given in
Allowed
4 Annexure-III-A. (Mandatory in case of tender for composite nature of work). In Yes Yes
(Mandatory)
case of JV firm, these details are also required for all the members of the JV
firm. In case, the Secondary Component(s) has/ have been defined, the
details of successfully completed works of similar nature (that defined for the
Secondary Component), executed by tenderer himself / the subcontractor
(fully by any one or jointly i.e. partly by tenderer and remaining through
subcontractor) during last five years, shall also be submitted (for five years ).
The tenderer shall submit the Attested copy of Completion Certificate/
substentially completed of works mentioned in Standard Technical Criteria
under eligibility criteria above from the Organizations with whom they worked
as per proforma given in Annexure-IV-A or IV-B (If the work is substantially
completed) or IV- C (if the work is awarded by Public listed Company) as
Allowed
5 applicable. (Mandatory for all firms). In case of JV firm, these details are also Yes Yes
(Mandatory)
required for all the members of the JV firm. In case, the Secondary
Component(s) has/ have been defined, the Attested copy of Completion
Certificate of works executed by tenderer himself / the subcontractor (fully by
any one or jointly i.e. partly by tenderer and remaining through subcontractor)
during last five years, shall also be submitted.
Details of Average Annual turnover of the public listed company (company
should be 500 Cr and above) issued by Chartered Accountant. These details
Allowed
6 need to be submitted as per the proforma of Annexure VIII ( Mandatory in Yes Yes
(Optional)
case of completion certificate issued by public listed company as per annexure
IV- C)
The copy of the documents regarding listing in the National stock exchange or
Bombay stock exchange with details of status of listing as on date of opening Allowed
7 Yes Yes
of tender, duly self-attested. (Mandatory in case of completion certificate (Optional)
issued by public listed company as per annexure IV-C)
The copy of the document of incorporation/ registration of the Public listed
company (should be at least 5 years prior to date of closing of tender), duly Allowed
8 Yes Yes
self-attested. ( Mandatory in case of completion certificate issued by public (Optional)
listed company as per annexure IV- C)
The copy of document regarding Person Authorized by the Public listed
Allowed
9 Company to issue such certificate, duly self-attested. ( Mandatory in case of Yes Yes
(Optional)
completion certificate issued by public listed company as per annexure IV- C)

TENDER DOCUMENT
Tenderer shall also submit the relevant copy of work order, bill of quantities bill
wise details of payment received duly certified by Chartered Accountant, TDS
certificates for all payments received a copy of final/last bill paid by the public Allowed
10 Yes Yes
listed company in support of above work experience certificate duly self- (Optional)
attested.(Mandatory in case of completion certificate issued by public listed
company as per annexure IV- C)
The tenderer shall submit the self attested copy of the PERMANENT Allowed
11 Yes Yes
ACCOUNT NO. issued by the Income Tax Department. (Optional)
The average annual contractual turnover shall be calculated as an average of
"total contractual payments" in the previous three financial years, as per the
audited balance sheet. However, in case balance sheet of the previous year is
yet to be prepared/ audited, the audited balance sheet of the fourth previous
Allowed
12 year shall be considered for calculating average annual contractual turnover. Yes Yes
(Mandatory)
The tenderers shall submit requisite information as per Annexure-VIII, along
with copies of Audited Balance Sheets duly certified by the Chartered
Accountant/ Certificate from Chartered Accountant duly supported by Audited
Balance Sheet.
A statement showing construction works executed and payment received in
any one of the previous three financial years or the current financial year (up
to date of inviting tender) taking into account the completed as well as work in
Allowed
13 progress as per Annexure-XIX on the letter head of Chartered Accountant, to Yes Yes
(Optional)
evaluate bid capacity of the tenderer (Mandatory for tender value more than
Rs. 20 Crores). In case of JV firm details of construction works executed by
each member of JV is required to be submitted
The tenderer should submit the List of works on hand, existing commitments
and balance amount of ongoing works as per proforma given in 'Annexure-V Allowed
14 Yes Yes
to evaluate bid capacity of the tenderer, duly verified by the Chartered (Optional)
accountant (Mandatory for tender value more than Rs. 20 crores)
The tenderer should submit the List of plants & Machinery available on hand
Allowed
15 (own) and proposed to be inducted/ Hired (own and hired to be given Yes Yes
(Optional)
separately) for the subject work in Annexure-VI.
The tenderer should submit the List of Personnel, Organization available on Allowed
16 Yes Yes
hand and proposed to be engaged for the subject work in Annexure -VII. (Optional)
The tenderer in the capacity of Sole Proprieter tenderer shall submit the
affidavit duly executed on stamp paper and notarized as per Annexure IX. Allowed
17 Yes Yes
(Mandatory for Sole Proprietership Firm/ forJV firm having Sole Proprieter firm (Optional)
as a member)
The tenderer shall submit the Power of Attorney duly registered with registrar
or notarized as per proforma given in Annexure XIV to be submitted by sole
proprietor firm duly registrar with the registrar or notarized. (Mandatory for Allowed
18 Yes Yes
Sole Proprietership Firm , if tender documents are uploaded by any individual (Optional)
,authorized by him) (Not required if tender documents are uploaded by
proprietor himself).
The tenderer in the capacity of HUF shall submit the affidavit duly executed on
Allowed
19 stamp paper and notarized as per Annexure XXVI. (Mandatory for HUF firm/ Yes Yes
(Optional)
for JV having HUF as a member) )
The tenderer in the capacity of HUF shall submit the Power of Attorney, duly
executed on stamp paper and duly registered with registrar/ notarized as per
Allowed
20 Annexure XXVII. (Mandatory for HUF firm)( Required , if tender documents are Yes Yes
(Optional)
uploaded by any individual ,authorized by him) (Not required if tender
documents are uploaded by Karta himself).
The tenderer as partnership firm shall submit copy of partnership deed (duly
registered with registrar or Notarized prior to the date of tender opening as per Allowed
21 Yes Yes
Indian partnership Act) (Mandatory for Partnership Firm /JV Firm having (Optional)
partnership firm as a member)
The tenderer as partner ship firm shall submit the Power of Attorney (duly
registered with registrar or notarized) as per proforma given in Annexure-XIII
Allowed
22 to be submitted by Partnership firm. (Mandatory for Partnership Firm) Yes Yes
(Optional)
(Required even if one or more partners are authorized in Partnership deed to
sign and upload the offer on behalf of the firm.)
The tenderer in the capacity of Company shall submit the Copy of
Allowed
23 Memorandum of Association / Articles of Association of Company. (Mandatory Yes Yes
(Optional)
for Company Firm / JV Firm having having Company as a member)

TENDER DOCUMENT
The tenderer in the capacity of Company shall submit the copy of resolution
Allowed
24 passed by Board of Directors authorizing its Director/Employee to deal with Yes Yes
(Optional)
tender on behalf of company.(Mandatory for Company Firm)
The tenderer in the capacity of company shall submit the Copy of Certificate of
Allowed
25 Incorporation of the Company. (Mandatory for Company Firm/JV Firm having Yes Yes
(Optional)
having Limited Company as a member)
The tenderer in the capacity of company shall submit the Power of Attorney/
Authorization (duly registered with registrar or notarized) including ratification
clause duly signed by person authorized by the company as per proforma Allowed
26 Yes Yes
given in Annexure-XV. (Mandatory for Company Firm)( Required even if (Optional)
tender documents are submitted by the authorized/ power of attorney holder
himself as per resolution passed by Board of Directors)
The tenderer in the capacity of Limited liabilities Partnership firm (LLP firm)
Allowed
27 shall submit the copy of LLP Agreement (Mandatory for LLP firm /JV Firm Yes Yes
(Optional)
having LLP Firm as a member)
Allowed
28 shall submit the copy of Certificate of Incorporation (Mandatory for LLP firm Yes Yes
(Optional)
/JV Firm having LLP Firm as a member)
shall submit the copy of Resolution of Partners of LLP firm (executed on the
Allowed
29 Letter Head of LLP firm) in favour of the individual to sign he tender on behalf Yes Yes
(Optional)
of the LLP firm and deal with tender on dehalf of the firm as per proforma
given in Annexure-XX.(Mandatory for LLP firm).
The tenderer in the capacity of Registered Society/ Registered Trust shall
submit the copy of the certificate of registration (Mandatory for Registered Allowed
30 Yes Yes
Society/ Registered Trust and JV firm having Registered Society/ Registered (Optional)
Trust as a member)
The tenderer in the capacity of Registered Society/ Registered Trust shall
submit the copy of the Deed of Formation (Mandatory for Registered Society/ Allowed
31 Yes Yes
Registered Trust and JV firm having Registered Society/ Registered Trust as a (Optional)
member)
A copy of power of attorney in favour of the individual to sign the tender Allowed
32 Yes Yes
document and create liabilities against society/trust (Annexxure XXI) (Optional)
The tenderer in the capacity of JV firm shall submit the Memorandum of
Allowed
33 Understanding of JV duly notarized as per proforma given in Annexure-X. Yes Yes
(Optional)
(Mandatory for Joint Venture Firm)
The private/ limited company, sole propriter firm or HUF/Society/Trust
partcipating as a member of JV shall submit t h e Power of Attorney duly
registered with registrar or notarized as per proforma given in Annexure-XII
(Mandatory), (For private/ limited company as member of JV- the annexure XII Allowed
34 Yes Yes
is required evenif MOU/JV agreement is signed by the authorized/ Power of (Optional)
attorny holder himself as per the Copy of Resolution) (For sole propriter
firm/HUF as member of JV- Not required if MOU/JV agreement is signed by
the proprieter of the sole propriter firm/ karta of HUF himself)
The tenderer in the capacity of JV firm shall submit the Letter of consent duly
executed on stamp paper as per proforma given in Annexure-XI to be Allowed
35 Yes Yes
submitted by a partnership firm participating as a Member of JV firm. (Optional)
(Mandatory for Joint Venture Firm if one of the member is Partnership firm)
The tenderer inthe capacity of JV firm shall submit the Power of Attorney duly
registered with registrar or notarized in favour of the individual to sign the
MOU/JV agreement on behalf of the partnership firm and create libility against
Allowed
36 the firm as per proforma given in Annexure-XVIII.(Mandatory for Joint Venture Yes Yes
(Optional)
Firm if one of the member is Partnership firm) (Required evenif MOU/JV
agreement is signed by one or more partners authorised in the partnership
deed, letter of consent )
shall submit submit the Power of Attorney duly registered with registrar or
notarized, issued by LLP firm as per proforma given in Annexure-XX. Allowed
37 Yes Yes
(Mandatory for LLP firm/ for JV having LLP as member) ( Required even if (Optional)
tender documents are submitted by the authorized/ power of attorney holder
himself as per resolution passed by Parters of the LLP)

TENDER DOCUMENT
The tenderer in the capacity of JV firm shall submit the Copy of Resolution of
the Partners of LLP firm, permitting the LLP firm to enter into a JV agreement,
authorizing one of the partner of LLP firm to sign MOU/JV Agreement and
Allowed
38 such other documents required to be signed on behalf of the LLP firm and to Yes Yes
(Optional)
create libilities against the LLP firm and / or to do any other act on behalf of
the LLP firm as per proforma given in Annexure-XXIII (Mandatory for JV firm if
one of the member is LLP firm).
The tenderer inthe capacity of JV firm shall submit the Power of Attorney duly
registered with registrar or notarized (Backed by Resolution of the Partners of
LLP firm) in favour of individual to sign the tender, to sign MOU/JV Agreement Allowed
39 Yes Yes
on behalf of the LLP firm and create liability against the LLP firm as per (Optional)
proforma given in Annexure-XXIV. (Mandatory for JV firm if one of the member
is LLP firm).
The tendere in the capacity of JV firm shall submit the copy of resolution
passed by Board of Directors of the Company, permitting the company to
enter into a JV agreement, authorizing MD or one of the Directors of Mangers
of the Company to sign JV Agreement, such other documents required to be Allowed
40 Yes Yes
signed on behalf of the Company and enter into liability against the company (Optional)
and/or do any other act on behalf of the company to be submitted as per
Annexure-XVII. ( Mandatory for JV firm if one of the member is Limited
Company)
The tenderers shall submit the information and particulars regarding retired
Railway Engineer(s)/Officer(s) of the Gazetted rank and regarding Relative(s) Allowed
41 Yes Yes
employed in Gazetted capacity on North Western Railway as per proforma (Mandatory)
given in Annexure XXII (Mandatory)
The tenderer in the capacity of newly formed Partnership Firm/ LLP Firm, shall
submit Declaration as per ANNEXURE XXVIII (Mandatory if tenderer is Newly
Formed Partnership Firm/ LLP Firm. The following relevant documents are
Annexed with bid - (mandatory as applicable) (1) Details of previous Propriety
firm / Partnership Firm/ LLP firm as per annexure I (2) A copy of previous
partnership Firm (Notarized or duly registered with the Registrar) (3) Affidavit
as per proforma given of Annexure -IX for previous Propriety firm (duly
Allowed
42 executed on stamp paper and notarized). (4) Copy of previous LLP agreement Yes Yes
(Optional)
and certificate of incorporation. (5) Dissolution deed/ splitting deed of the
previous partnership deed or LLP agreement (in case of dissolution of
previous partnership firm/ LLP firm) (6) Proof of surrender of previous PAN no
(in case of dissolution of previous partnership firm, LLP firm or propriety firm)
(7) Documents for the technical, financial criteria, bid capacity as claimed w.r.t.
such partner(s) joining the new/ existing partnership firm, as per para 16.1 (c ),
(d), (f),(g ), (k) of Bid document.
The tenderer in the capacity of existing Partnership Firm/ LLP Firm, shall
submit Declaration as per Annexure XXXIX (Mandatory if tenderer is existing
Partnership Firm/ LLP Firm. The following relevant documents are Annexed
with bid - (mandatory as applicable) (1) Details of previous Propriety firm /
Partnership Firm/ LLP firm as per annexure I. (2) A copy of previous
partnership Firm (Notarized or duly registered with the Registrar) (3) Affidavit
as per proforma given of Annexure -IX for previous Propriety firm (duly
Allowed
43 executed on stamp paper and notarized). (4) Copy of previous LLP agreement Yes Yes
(Optional)
and certificate of incorporation. (5) Dissolution deed/ splitting deed of the
previous partnership deed or LLP agreement (in case of dissolution of
previous partnership firm/ LLP firm) (6) Proof of surrender of previous PAN no
(in case of dissolution of previous partnership firm, LLP firm or propriety firm)
(7) Documents for the technical, financial criteria, bid capacity as claimed w.r.t.
such partner(s) joining the new/ existing partnership firm, as per para16.1 (c ),
(d), (f),(g ), (k) of Bid document

TENDER DOCUMENT
The tenderer in the capacity of existing/ New Company, shall submit

Declaration regarding constitution of the existing/ New Company as per
Annexyre XXX (Mandatory if tenderer is merged Company). The following
relevant documents are Annexed with bid - (mandatory as applicable) (1)
Details of company getting merged as per annexure I (2) Copy of
Memorandum of Association/ Articles of Association of the Company getting Allowed
44 Yes Yes
merged (3) Copy of certificate of incorporation of previous company getting (Optional)
Merged. (4) Resolution by the Board of Directors for the Merger of the
company(s) with the tenderer (5) Proof of surrender of previous PAN no (6)
Documents for the technical, financial criteria, bid capacity as claimed w.r.t.
such Company(s) joining the new/ existing Company, as per para 16.1 (c ),
(d), (f), (g ), (k) of Bid document
Tenderer shall submit a formal agreement duly notarized, legally enforceable
in the court of law, executed by tenderer with the subcontractor for the
component(s) of work proposed to be executed by the subcontractor(s), and Allowed
45 Yes Yes
shall be submitted along with the offer as per performa given in Annexure (Optional)
XXXI.(Mandatory in case of secondary components are defined in the tender
with special condition 'for submission along with the Offer)
Undertakings

I/ We have visited the works site and I / We am / are aware of the site
1 No No Not Allowed
conditions.
I/We have read the various conditions to tender attached here to and agree to
abide by the said conditions. I/We also agree to keep this tender open for
acceptance for a period as mentioned in NIT header from the date fixed for
opening the same and in default thereof, I/We will be liable for forfeiture of
2 No No Not Allowed
my/our "Bid security". I/We offer to do the work for North Western Railway, at
the rates quoted in the attached schedule and hereby bind myself/ourselves to
complete the work in all respects within time period as mentioned in the NIT
Header from the date of issue of letter of acceptance of the tender.
I/We also hereby agree to abide by the General Conditions of Contract-2022
corrected up- to- date and to carry out the work according to the Special
Conditions of Contract and Indian Railways Unified Standard Specifications
3 No No Not Allowed
(Materials and Works) 2021 as corrected up-to-date, Unified Standard
Schedule of Rates of North-Western Railway - 2021 as corrected up-to-date &
CPWD DSR-2021 and Specification 2019 (for the present contract)
An amount towards Bid Security As mentioned in the relevant Para of NIT
header has been submitted online through net banking or payment gateway or
Bank gurantee. The full value of the Bid security shall stand forfeited without
prejudice to any other right or remedies in case my/our tender is accepted and
4 No No Not Allowed
if:- (a) I/We do not execute the contract documents within seven days after
receipt of notice issued by the Railway that such documents are ready; and (b)
I/We do not commence the work within fifteen days after receipt of orders to
that effect.
Until a formal agreement is prepared and executed, acceptance of this tender
shall constitute a binding contract between us subject to modifications, as may
5 No No Not Allowed
be mutually agreed to between us and indicated in the letter of acceptance of
my/our offer for this work.
The tenderer shall submit the original copies of the documents as per
Annexure II, IIA, IX, X, XI, XII, XIII, XIV, XV, XVII, XVIII, XX, XXI, XXII, XXIII,
XXIV ,XXV, XXVI, XXVII, XXVIII, XXXIX, and XXXII or other document as
applicable for Sole Proprietor/ HUF/Partnership firm/LLP firm/ Registered
Society / Registered Trust /Limited Company/JV Firms as and when required
6 by the Railway for the verification. If the required documents are not submitted No No Not Allowed
by the tenderer or there any discrepancy is found between the scanned
uploaded documents by the tenderer and original documents then the offer of
the concerned tenderer will be summary rejected and the action will be taken
as per the various provisions of certificate to be submitted by the tenderer as
per Annexure-II, IIA

TENDER DOCUMENT
The tenderer shall comply with the provisions of the Contract Labour
(Regulation and Abolition) Act 1970 and the Contract Labour (Regulation and
7 Abolition) Central Rules 1971 as modifed from time to time, wherever No No Not Allowed
applicable and shall also indemnify the Railway from and against any claims
under the aforesaid Act and Rules.
The tenderer shall comply with the provisions of the Payment of Wages Act
1936, Minimum Wages Act 1948, The Workmen Compensation Act 1923, and
the rules made there under in respect of any employees employed directly or
8 No No Not Allowed
through petty contractors or sub-contractors engaged by them, as modifed
from time to time, wherever applicable and shall also indemnify the Railway
from and against any claims under the aforesaid Act and Rules.
The tenderer shall comply with the provisions of the Employees provident fund
and Miscellaneous Provision Act 1952 and the rules made there under as
9 No No Not Allowed
modifed from time to time, wherever applicable and shall also indemnify the
Railway from and against any claims under the aforesaid Act and Rules.
The tenderer shall comply with the provisions of the Employees State
Insurance Act 1948 and Employees Pension Scheme 1995 and the rules
10 made there under as modifed from time to time, wherever applicable and shall No No Not Allowed
also indemnify the Railway from and against any claims under the aforesaid
Act and Rules.
The successful tenderer after award of the contract shall register himself on
website www.shramikkalyan.indianrailways.gov.in and will comply the
11 No No Not Allowed
provisions of the Para 39 of the Special Conditions (General) of Standard
Tender Document.
I/We have read the various conditions of clause no. 26 of General Instructions
12 of Tender Document a n d Special Condition of NIT regarding Electronic No No Not Allowed
Reverse Auction and agree to abide by the said conditions.
Certify that neither I /We (name of the sole Proprietor firm/ Partnership
Firm/Limited Company/ LLP/Registered Society/Trust / JV firm) nor any of the
partner or partnership firm/ LLP /Member of Registered Society/ Trust /
Constituent of JV firm including partner of partnership firm in JV has/ have
13 No No Not Allowed
been black listed or debarred by Railway or any other Ministry /Department/
Public Sector Undertaking of the Government of India/ any State from
participation in tenders/contract on the date of opening of bids either in our
individual capacity or in any firm in which we are partners.
6. Documents attached with tender
S.No. Document Name Document Description

1 StandardTenderDocumentPDF....pdf Standard Tender Document
2 AdditionalSpecialConditionofContractPDF....pdf Additional Special Conditions of co
SPECIALCONDITIONANDSPECIFICATIONOFNON-
3 Special Conditions and Specificatio
SCHEDULEITEMSch-CPDF.....pdf
SPECIALCONDITIONSOFCONTRACTTECHNICAL-ELECTRICAL-
4 Special condition of contract techn
SCHEDULE-D.pdf
5 TechnicalSpecificationElectricalforSchedule-D.pdf Technical Specification Electrical
6 GCC2022April.pdf GCC April 2022
7 ACSNo.1GCC-2022.pdf GCC Correction slip no 1
8 GCCAdvanceCorrectionslipNo2.pdf GCC correction Slip No 02
9 GCCAdvancecorrectionslipNo3.pdf GCC correction Slip No 03
10 GCCAdvanceCorrectionSlipNo_4ACS-4_1.pdf GCC correction Slip No 04
11 GCCAdvanceCorrectionSlipNo_5ACS-53_1.pdf GCC correction Slip No 05
12 Correctedcompendiumofinstructiononsafetyatworkssite31.3.14.pdf Corrected compendium of instruction
2023_12_21IndianRailwaysStandardGeneralConditionsofContractApril-
13 GCC correction Slip No 06
2022AdvanceCorrectionSlipNo_6ACS-61.pdf
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by
Department of Induswww Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.
2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.

TENDER DOCUMENT
As a Tender Inviting Authority, the undersigned has ensured that the issue of this tender does not violate provisions of
GFR regarding procurement through GeM.
Signed By: VIJAI SINGH MEENA
Designation : Dy.CE/C/Bikaner

viewNitPdf 4487818

Uploaded by

Copyright:

Available Formats

viewNitPdf 4487818

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

viewNitPdf 4487818

Uploaded by

Copyright:

Available Formats

DYCE-C-BKN-ENGINEERING/NORTH WESTERN RLY

Auto Elimination rules

Pa g e 1 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 2 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 4 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

NS14 69.00 Numbers 55.00 3795.00 AT Par 3795.00

Pa g e 5 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 6 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

022035 135.00 cum 2944.12 397456.20 (-) 12.53 347654.94

Pa g e 8 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 9 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Schedule Schedule B-CPWD DSR-2021 Items

Pa g e 10 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and laying cement concrete in retaining walls,

Pa g e 11 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 12 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

5.33.1 All works upto plinth level

Pa g e 13 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 14 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and fixing M.S. grills of required pattern in

Pa g e 15 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 16 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and fixing hand rail of approved size by

Pa g e 17 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Kota stone slab flooring over 20 mm (average) thick

Pa g e 18 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

12.1S SHEET ROOFING

Pa g e 19 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and fixing precoated galvanised steel sheet

Pa g e 2 0 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

13.71 per 25000 5.05 126250

Pa g e 2 1 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

3 16.3.2 63 mm to 45 mm size stone aggregate cum 3039 1624.5 4936855.5

Pa g e 2 2 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 2 3 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 2 4 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 2 5 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and fixing Chlorinated Polyvinyl Chloride

Pa g e 2 6 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Providing and fixing C.P. brass stop cock (concealed) of

Pa g e 2 7 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Extra for depth beyond 45 cm of brick masonry chamber

Pa g e 2 8 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Boring/drilling bore well of required dia for casing/

Special Financial Criteria

S.No. Description Confirmation Remarks Documents

Pa g e 2 9 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Special Technical Criteria

S.No. Description Confirmation Remarks Documents

Pa g e 30 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

S.No. Description Confirmation Remarks Documents

S.No. Description Confirmation Remarks Documents

Pa g e 31 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

S.No. Description Confirmation Remarks Documents

Pa g e 32 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 33 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 34 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

Pa g e 35 o f 38 Ru n Da te/Time: 0 9 /0 3/2 0 2 4 14:2 0 :5 5

The tenderer in the capacity of existing/ New Company, shall submit