FERROXCUBE

DATA SHEET

ETD34/17/11
ETD cores and accessories
Supersedes data of September 2004 2008 Sep 01
Ferroxcube

ETD cores and accessories ETD34/17/11

CORE SETS
Effective core parameters
handbook, halfpage
SYMBOL PARAMETER VALUE UNIT 0.6
11.8
0 17.3
Σ(I/A) core factor (C1) 0.810 mm−1 0.2

Ve effective volume 7640 mm3

Ie effective length 78.6 mm
Ae effective area 97.1 mm2 0
35 1.6
Amin minimum area 91.6 mm2 1.4
25.6 0
m mass of core half ≈ 20 g 0
11.1 0.6

0
11.1
0.6

MGC176

Dimensions in mm.

Fig.1 ETD34/17/11 core half.

Core halves
Clamping force for AL measurements, 40 ±20 N. Gapped cores are available on request.

AL AIR GAP
GRADE µe TYPE NUMBER
(nH) (µm)
3C90 2700 ±25% ≈ 1740 ≈0 ETD34/17/11-3C90
3C94 2700 ±25% ≈ 1740 ≈0 ETD34/17/11-3C94
3C95 3270 ±25% ≈ 2110 ≈0 ETD34/17/11-3C95
3C96 2500 ±25% ≈ 1610 ≈0 ETD34/17/11-3C96
3F3 2500 ±25% ≈ 1610 ≈0 ETD34/17/11-3F3
3F35 1850 ±25% ≈ 1190 ≈0 ETD34/17/11-3F35

2008 Sep 01 2
Ferroxcube

ETD cores and accessories ETD34/17/11

Properties of core sets under power conditions

B (mT) at CORE LOSS (W) at

GRADE H = 250 A/m; f = 25 kHz; f = 100 kHz; f = 100 kHz; f = 100 kHz; f = 400 kHz;
f = 25 kHz; B̂ = 200 mT; B̂ = 100 mT; B̂ = 200 mT; B̂ = 200 mT; Bˆ = 50 mT;
T = 100 °C T = 100 °C T = 100 °C T = 25 °C T = 100 °C T = 100 °C
3C90 ≥330 ≤ 0.92 ≤ 0.97 − − −
3C94 ≥330 − ≤ 0.73 − ≤ 4.2 −
3C95 ≥330 − − ≤ 4.51 ≤ 4.28 −
3C96 ≥340 − ≤ 0.55 − ≤ 3.4 −
3F3 ≥320 − ≤ 0.9 − − ≤ 1.6
3F35 ≥300 − − − − −

Properties of core sets under power conditions (continued)

B (mT) at CORE LOSS (W) at

GRADE H = 250 A/m; f = 500 kHz; f = 500 kHz; f = 1 MHz; f = 3 MHz;

f = 25 kHz; Bˆ = 50 mT; Bˆ = 100 mT; ˆ = 30 mT;
B ˆ = 10 mT;
B
T = 100 °C T = 100 °C T = 100 °C T = 100 °C T = 100 °C
3C90 ≥330 − − − −
3C94 ≥330 − − − −
3C95 ≥330 − − − −
3C96 ≥340 ≤ 2.8 − − −
3F3 ≥320 − − − −
3F35 ≥300 ≤ 1.0 ≤ 8.0 − −

2008 Sep 01 3
Ferroxcube

ETD cores and accessories ETD34/17/11

COIL FORMERS
General data 14-pins ETD34/17/11 coil former
PARAMETER SPECIFICATION
Coil former material polybutyleneterephtalate (PBT), glass-reinforced, flame retardant
in accordance with “UL 94V-0”; UL file number E45329(R)
Pin material copper-tin alloy (CuSn), tin (Sn) plated
Maximum operating temperature 155 °C, “IEC 60085”, class F
Resistance to soldering heat “IEC 60068-2-20” , Part 2, Test Tb, method 1B, 350 °C, 3.5 s
Solderability “IEC 60068-2-20”, Part 2, Test Ta, method 1

39.6 max.
35.3 min. 42.8 max.
0 0
25.4 −0.2 23.4 −0.2
handbook, full pagewidth 11.4 +0.1
0 20.9 min.

5.08

0
∅13.4 −0.2
32.9
max.

4
1.6 +0.15
0
CBW280

5.08 0.8 5.08

30.48 25.4
Dimensions in mm.

Fig.2 ETD34/17/11 coil former; 14-pins.

Winding data and area product for 14-pins ETD34/17/11 coil former

MINIMUM AVERAGE AREA

WINDING
NUMBER OF WINDING LENGTH OF PRODUCT
AREA TYPE NUMBER
SECTIONS WIDTH TURN Ae x Aw
(mm 2)
(mm) (mm) (mm4)
1 123 20.9 60 11900 CPH-ETD34-1S-14P(1)

Note
1. Also available with ∅1.0 mm pins.

2008 Sep 01 4
Ferroxcube

ETD cores and accessories ETD34/17/11

General data 14-pins coaxial ETD34/17/11 coil former

PARAMETER SPECIFICATION
Coil former material phenolformaldehyde (PF), glass-reinforced, flame retardant
in accordance with “UL 94V-0”; UL file number E167521(M)
Pin material copper-tin alloy (CuSn), tin (Sn) plated
Maximum operating temperature 180 °C, “IEC 60085”, class H
Resistance to soldering heat “IEC 60 068-2-20”, Part 2, Test Tb, method 1B, 350 °C, 3.5 s
Solderability “IEC 60 068-2-20”, Part 2, Test Ta, method 1

32.6 max 39.8 max

handbook, full pagewidth 0 0
21.15 25.4 0.2
0.1
(17.05 min) 0.2
11.4
0

0.15
O13.1 0

4.5

O1 5.08
2.7 30.48 MGC178

39.8 max 42.9 max

handbook, full pagewidth 0 0
25.4 0.2 21.7 0.15
0.2 (18.85 min)
11.4 0

0.15 O 20.15
O18.4 0 0.1
32.6
max

MGC179

4.5

5.08 O1
30.48 22.7

Dimensions in mm.
For mounting grid and method of fitting, see Fig.4.

Fig.3 Coaxial ETD34/17/11 coil former; 14-pins.

2008 Sep 01 5
Ferroxcube

ETD cores and accessories ETD34/17/11

5.08
handbook, full pagewidth 0.1

CSCI-ETD34-1S-7P

14 8

CSCO-ETD34-1S-7P

CBW590
PH 1.6 +0.15
0
1 ETD34 7

Dimensions in mm.
This coil former incorporates 8 mm creepage distance between primary and secondary windings, as
well as between primary and all other conductive parts (in accordance with IEC 380 safety regulations).

Fig.4 Mounting grid and method of fitting.

Winding data and area product for coaxial ETD34/17/11 coil former

MINIMUM AVERAGE AREA

WINDING
NUMBER OF WINDING LENGTH OF PRODUCT
AREA TYPE NUMBER
SECTIONS WIDTH TURN Ae x Aw
(mm2)
(mm) (mm) (mm4)
1 42.6 17.05 49.4 4140 CSCI-ETD34-1S-7P
1 46.6 18.85 71.4 4520 CSCO-ETD34-1S-7P

2008 Sep 01 6
Ferroxcube

ETD cores and accessories ETD34/17/11

MOUNTING PARTS
General data

ITEM REMARKS FIGURE TYPE NUMBER

Mounting clip material: stainless steel 5 CLI-ETD34

handbook, halfpage9

22 37.8 min

MGC181 0.4 11

Dimensions in mm.

Fig.5 Mounting clip for ETD34/17/11.

2008 Sep 01 7
Ferroxcube

ETD cores and accessories ETD34/17/11

DATA SHEET STATUS DEFINITIONS

DATA SHEET PRODUCT

DEFINITIONS
STATUS STATUS
Preliminary Development This data sheet contains preliminary data. Ferroxcube reserves the right to
specification make changes at any time without notice in order to improve design and
supply the best possible product.
Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right
to make changes at any time without notice in order to improve design and
supply the best possible product.

DISCLAIMER
Life support applications  These products are not designed for use in life support appliances, devices, or systems
where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers
using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube
for any damages resulting from such application.

PRODUCT STATUS DEFINITIONS

STATUS INDICATION DEFINITION

These are products that have been made as development samples for the purposes of
Prototype technical evaluation only. The data for these types is provisional and is subject to
change.
Design-in These products are recommended for new designs.
These products are recommended for use in current designs and are available via our
Preferred
sales channels.
These products are not recommended for new designs and may not be available
Support
through all of our sales channels. Customers are advised to check for availability.

2008 Sep 01 8