ASME B36.

10M-2015
[Revision of ASME B36.10M-2004 (R2010)]

Welded and
Seamless
Wrought Steel
Pipe

A N A M E R I C A N N AT I O N A L STA N DA R D
 ASME B36.10M-2015
[Revision of ASME B36.10M-2004 (R2010)]

Welded and
Seamless
Wrought Steel
Pipe

A N A M E R I C A N N AT I O N A L S TA N D A R D

Two Park Avenue • New York, NY • 10016 USA

 Date of Issuance: August 31, 2015

This Standard will be revised when the Society approves the issuance of a new edition.

Periodically certain actions of the ASME B32 Committee may be published as Cases. Cases are
published on the ASME Web site under the B32 Committee Page at go.asme.org/B32committee as
they are issued.

Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to
provide corrections to incorrectly published items, or to correct typographical or grammatical errors
in codes and standards. Such errata shall be used on the date posted.

The B32 Committee Page can be found at go.asme.org/B32committee. There is an option available
to automatically receive an e-mail notification when errata are posted to a particular code or standard.
This option can be found on the appropriate Committee Page after selecting “Errata” in the “Publication
Information” section.

ASME is the registered trademark of the American Society of Mechanical Engineers.

This code or standard was developed under procedures accredited as meeting the criteria for American National
Standards. The Consensus Committee that approved the code or standard was balanced to assure that individuals from
competent and concerned interests have had an opportunity to participate. The proposed code or standard was made
available for public review and comment that provides an opportunity for additional public input from industry, academia,
regulatory agencies, and the public-at-large.
ASME does not ‘‘approve,’’ ‘‘rate,’’ or ‘‘endorse’’ any item, construction, proprietary device, or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in connection with any
items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for
infringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expressly
advised that the determination of the validity of any such patent rights, and the risk of infringement of such rights, is
entirely their own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as
government or industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretations of this document issued in accordance with the established
ASME procedures and policies, which precludes the issuance of interpretations by individuals.

No part of this document may be reproduced in any form,

in an electronic retrieval system or otherwise,
without the prior written permission of the publisher.

The American Society of Mechanical Engineers

Two Park Avenue, New York, NY 10016-5990

Copyright © 2015 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All rights reserved
Printed in U.S.A.
 CONTENTS

Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Correspondence With the B32 Committee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 Wall Thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 Permissible Variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7 Pipe Threads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8 Wall Thickness Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
9 Wall Thickness Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table
1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe . . . . . . . . . . . . . . . 3

iii
 FOREWORD

In March 1927, the American Standards Association authorized the organization of a Sectional
Committee on Standardization of Dimensions and Material of Wrought Steel and Wrought Iron
Pipe and Tubing for the purpose of unifying the standards of these commodities in force in this
country. The American Society for Testing and Materials and The American Society of Mechanical
Engineers were designated as sponsors, and the first meeting of the Sectional Committee was
held in Pittsburgh, Pennsylvania, on May 18, 1928.
The dimensions of commercial pipe in general use in the United States at the time conformed
rather generally to those recommended by the ASME Committee on Standard Pipe and Pipe
Threads published in 1886 (ASME Transactions, Vol. VIII, p. 29). On these standards an enormous
industry has been built and the satisfactory use of this product proves the soundness of the
original design and specification.
Increasingly severe service demands at the time of the Committee’s organization had been met
by using the nearest available pipe or tubing for heavier sections such as casing, mechanical
tubing, etc., with resulting uneconomical multiplicity of wall thicknesses.
Subsequently, the Committee, with the cooperation of the industry, made a survey of existing
practice as the logical starting point for the development of an American Standard. From this
survey, a table was designed to provide a selection of wall thicknesses of pipe to cover the power
piping requirements of industry where strength to resist internal pressure governs selection and
was later expanded to include pipe diameters and thicknesses used in other industries.
The original intent of the Committee was to establish a system of Schedule Numbers for pipe
size/wall thickness combinations which would have an approximately uniform relationship equal
to 1000 times the P/S expression contained in the modified Barlow formula for pipe wall thickness
as defined in the Appendix* to this standard. The resulting Numbers departed so far from existing
wall thicknesses in common use that the original intent could not be accomplished. The Schedule
Numbers were then adopted strictly as a convenient designation system for use in ordering.
In all cases, the designer must base his selection on the rules and allowable stresses set by the
code which governs his particular construction. The table is dimensionally complete for all sizes
and wall thicknesses within its scope, but some of the larger, heavier wall sections are beyond
the capability of seamless mill production and must be obtained from forged and bored billets
or other sources.
The first issue of this standard was given with the designation American Standard “tentative”
by the American Standards Association in November 1935. Subsequent slight revisions to Table 1
and the footnotes of the dimensional tables were approved and the ASA changed the designation
to American Standard; the date of ASA approval was April 28, 1939.
Further revisions were made by the Sectional Committee. The list of specifications in Table 1
was revised where necessary and slight revisions in wall thicknesses of some of the large sizes
of the heavy schedules were made where P/S values were out of line.
It was the hope in 1939 that the designation of pipe used commercially by all industry as
Standard weight, Extra-Strong, and Double Extra-Strong would gradually be replaced by Schedule
Number designation. However, owing to customs of over 50 years’ standing, demand and produc-
tion of pipe to these traditional dimensions is undiminished. Consequently, in response to a
demand from users, accepted practice for dimensions and weights of commercial wrought steel
and welded wrought iron pipe were added. These changes were designated an American Standard
on February 23, 1950.

* This Appendix, which appeared in the 1975 edition, was later removed.

iv
 Subcommittee No. 1 was reorganized in 1957. In addition to necessary editorial changes, a
simplified format was selected for the tables of weights and dimensions so as to include and
identify the sizes and weights of API Standards 5L and 5LX. These changes to the standard were
approved and it was designated an American Standard on December 21, 1959.
The standard was revised in 1969. A uniform method to calculate the plain end weight of steel
pipe was included, and minor adjustments were made in the tabulated weights of steel pipe in
Table 2 to conform to this new method. Additional sizes and thicknesses of steel pipe that had
come into common use were also added to Table 2. Inasmuch as API Standard 5L no longer
included wrought iron pipe, reference to this API Standard was deleted from Table 3. These
changes to the standard were approved and it was designated an American National Standard
on February 3, 1970.
Further revisions were made to the standard in 1975. Additional sizes and thicknesses of steel
pipe that had been added to API specifications were added to Table 2. Table 3, Dimensions and
Weights of Welded Wrought Iron Pipe, was deleted in its entirety, since wrought iron pipe is no
longer produced. These changes in the standard were approved and it was designated an American
National Standard on June 5, 1975.
The standard was revised in 1978 to include SI metric dimensions. The outside diameter and
wall thicknesses were converted to millimeters by multiplying the inch dimensions by 25.4.
Outside diameters larger than 16 in. were rounded to the nearest millimeter, and outside diameters
16 in. and smaller were rounded to the nearest 0.1 mm. Wall thicknesses were rounded to the
nearest 0.01 mm. These converted and rounded SI metric dimensions were added to Table 2. A
formula to calculate the SI metric plain end mass, in kilograms per meter, using SI metric diameters
and thicknesses was added to section 5. The SI metric plain end mass was calculated and was
added to Table 2. These changes in the standard were approved and it was designated an American
National Standard on July 18, 1979.
Further revisions were made in 1984. The ANSI designations, which are no longer in use, were
deleted from Table 1, and the list of specifications was revised to agree with current ASTM and
API specifications. Additional sizes and thicknesses which had been added to API specifications
were added to Table 2. That edition was approved as an American National Standard on
August 19, 1985.
The next edition included additional wall thicknesses and was approved by the American
National Standards Institute on August 24, 1995.
The 1996 edition contained revisions to Table 2, adding pipe sizes, changing some plain end
weights and masses, identifying metric pipe by the dimensionless designator DN, and eliminating
the API Specification column. The 1996 edition was approved as an American National Standard
on September 23, 1996.
The 2000 edition contained revisions to Table 2 to include the revised density for steel incorpo-
rated into section 5 previously. Table 1 was deleted and other editorial changes to Sections 1, 2,
3, 5, 8, and 9 were made. The 2000 edition was approved as an American National Standard on
December 1, 2000.
The 2004 edition contained revisions to section 5 and Table 1. It corrected the equation for
nominal plain end weight. It added the missing DN schedule numbers in Table 1. This edition
was approved as an American National Standard on June 23, 2004.
The 2015 edition contains revisions to Table 1 by removing Note (3) and its references. The
2015 edition was approved as an American National Standard on June 16, 2015.

v
 ASME B32 COMMITTEE
Metal and Metal Alloy
Wrought Mill Product Nominal Sizes
(The following is the roster of the Committee at the time of approval of this Standard.)

OFFICERS

J. A. Gruber, Chair
A. R. Amaral, Secretary

COMMITTEE PERSONNEL

A. R. Amaral, The American Society of Mechanical Engineers

D. O. Bankston, Jr., Consultant
D. Frikken, Becht Engineering Co.
J. A. Gruber, J A Gruber & Associates
R. A. McLeod, General Electric Co.
M. L. Nayyara, NICE
A. P. Rangus, Bechtel
R. Reamy, Turner Industries Group
M. H. Skinningberg, Consultant
F. W. Tatar, FM Global

vi
 CORRESPONDENCE WITH THE B32 COMMITTEE

General. ASME Standards are developed and maintained with the intent to represent the
consensus of concerned interests. As such, users of this Standard may interact with the Committee
by proposing revisions or a Case, and attending Committee meetings. Correspondence should
be addressed to:
Secretary, B32 Standards Committee
The American Society of Mechanical Engineers
Two Park Avenue
New York, NY 10016-5990
http://go.asme.org/Inquiry
Proposing Revisions. Revisions are made periodically to the Standard to incorporate changes
that appear necessary or desirable, as demonstrated by the experience gained from the application
of the Standard. Approved revisions will be published periodically.
The Committee welcomes proposals for revisions to this Standard. Such proposals should be
as specific as possible, citing the paragraph number(s), the proposed wording, and a detailed
description of the reasons for the proposal, including any pertinent documentation.
Proposing a Case. Cases may be issued for the purpose of providing alternative rules when
justified, to permit early implementation of an approved revision when the need is urgent, or to
provide rules not covered by existing provisions. Cases are effective immediately upon
ASME approval and shall be posted on the ASME Committee Web page.
Requests for Cases shall provide a Statement of Need and Background Information. The request
should identify the Standard and the paragraph, figure, or table number(s), and be written as a
Question and Reply in the same format as existing Cases. Requests for Cases should also indicate
the applicable edition(s) of the Standard to which the proposed Case applies.
Request that are not in this format may be rewritten in the appropriate format by the Committee
prior to being answered, which may inadvertently change the intent of the original request.
ASME procedures provide for reconsideration of any interpretation when or if additional
information that might affect an interpretation is available. Further, persons aggrieved by an
interpretation may appeal to the cognizant ASME Committee or Subcommittee. ASME does not
“approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device, or activity.
Attending Committee Meetings. The B32 Standards Committee regularly holds meetings and/
or telephone conferences that are open to the public. Persons wishing to attend any meeting
and/or telephone conference should contact the Secretary of the B32 Standards Committee. Future
Committee meeting dates and locations can be found on the Committee Page at
go.asme.org/B32committee.

vii
INTENTIONALLY LEFT BLANK

viii
 ASME B36.10M-2015

WELDED AND SEAMLESS WROUGHT STEEL PIPE

1 SCOPE where
D p outside diameter to the nearest 0.001 in. (the
This Standard covers the standardization of dimen-
symbol D is to be used for O.D. only in mathe-
sions of welded and seamless wrought steel pipe for
matical equations or formulas)
high or low temperatures and pressures.
t p specified wall thickness, rounded to the near-
The word pipe is used, as distinguished from tube, to
est 0.001 in.
apply to tubular products of dimensions commonly used
Wpe p nominal plain end mass, rounded to the near-
for pipeline and piping systems. Pipe NPS 12 (DN 300)
est 0.01 lb/ft
and smaller have outside diameters numerically larger
than their corresponding sizes. In contrast, the outside The nominal plain end mass, in kilograms per meter,
diameters of tubes are numerically identical to the size is calculated using the following formula:
number for all sizes.
Wpe p 0.0246615(D − t)t
2 SIZE where
The size of all pipe is identified by the nominal D p outside diameter to the nearest 0.1 mm for
pipe size. outside diameters that are 16 in. (406.4 mm)
The manufacture of pipe NPS 1⁄8 (DN 6) to NPS 12 and smaller and to the nearest 1.0 mm
(DN 300), inclusive, is based on a standardized outside for outside diameters larger than 16 in.
diameter (O.D.). This O.D. was originally selected so (406.4 mm) (the symbol D is to be used for
that pipe with a standard O.D. and having a wall thick- O.D. only in mathematical equations or
ness that was typical of the period would have an inside formulas)
diameter (I.D.) approximately equal to the nominal size. t p specified wall thickness, rounded to the near-
Although there is no such relation between the existing est 0.01 mm
standard thickness — O.D. and nominal size — these Wpe p nominal plain end mass, rounded to the near-
nominal sizes and standard O.D.s continue in use as est 0.01 kg/m
‘‘standard.’’
The manufacture of pipe NPS 14 (DN 350) and larger 6 PERMISSIBLE VARIATIONS
proceeds on the basis of an O.D. corresponding to the
nominal size. Variations in dimensions differ depending upon the
method of manufacture employed in making the pipe
to the various specifications available. Permissible varia-
3 MATERIALS tions for dimensions are indicated in each specification.
The dimensional standards for pipe described here
are for products covered in ASTM specifications. 7 PIPE THREADS
Unless otherwise specified, the threads of threaded
4 WALL THICKNESS pipe shall conform to ANSI / ASME B1.20.1, Pipe
The nominal wall thicknesses are given in Table 1. Threads, General Purpose (Inch).
Schedules 5 and 10 wall thicknesses do not permit
threading in accordance with ANSI/ASME B1.20.1.
5 WEIGHTS
The nominal weights of steel pipe are calculated val- 8 WALL THICKNESS DESIGNATIONS
ues and are tabulated in Table 1.
The wall thickness designations Standard,
The nominal plain end weight, in pounds per foot, is
Extra- Strong, and Double Extra-Strong have been com-
calculated using the following formula:
mercially used designations for many years. As
Wpe p 10.69(D − t)t explained in the Foreword, the Schedule Numbers were
subsequently added as a convenient designation for use

1
 ASME B36.10M-2015

in ordering pipe. Standard and Schedule 40 are identical 9 WALL THICKNESS SELECTION
for up to NPS 10 (DN 250), inclusive. All larger sizes of
When the selection of wall thickness depends primar-
Standard have 3⁄8 in. (9.53 mm) wall thicknesses. ily upon capacity to resist internal pressure under given
Extra-Strong and Schedule 80 are identical for up to conditions, the designer shall compute the exact value
NPS 8 (DN 200), inclusive. All larger sizes of of wall thickness suitable for conditions for which the
Extra-Strong have 1⁄2 in. (12.70 mm) wall thicknesses. pipe is required, as prescribed in detail in the
Pipe of sizes and wall thicknesses other than those of ASME Boiler and Pressure Vessel Code, ASME B31 Code
Standard, Extra-Strong, and Double Extra-Strong, and for Pressure Piping, or other similar codes, whichever
Schedule Number were adopted from API Specification governs the construction. A thickness shall be selected
5L. It was not considered practical to establish Schedule from Table 1 to suit the value computed to fulfill the
Numbers or new designations for them. conditions for which the pipe is desired.

2
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m
1
⁄8 0.405 0.049 0.19 ... 10 6 (3) 10.3 1.24 0.28
1
⁄8 0.405 0.057 0.21 ... 30 6 (3) 10.3 1.45 0.32
1
⁄8 0.405 0.068 0.24 STD 40 6 (3) 10.3 1.73 0.37
1
⁄8 0.405 0.095 0.31 XS 80 6 (3) 10.3 2.41 0.47
1
⁄4 0.540 0.065 0.33 ... 10 8 (3) 13.7 1.65 0.49
1
⁄4 0.540 0.073 0.36 ... 30 8 (3) 13.7 1.85 0.54
1
⁄4 0.540 0.088 0.43 STD 40 8 (3) 13.7 2.24 0.63
1
⁄4 0.540 0.119 0.54 XS 80 8 (3) 13.7 3.02 0.80
3
⁄8 0.675 0.065 0.42 ... 10 10 17.1 1.65 0.63
3
⁄8 0.675 0.073 0.47 ... 30 10 17.1 1.85 0.70
3
⁄8 0.675 0.091 0.57 STD 40 10 17.1 2.31 0.84
3
⁄8 0.675 0.126 0.74 XS 80 10 17.1 3.20 1.10
1
⁄2 0.840 0.065 0.54 ... 5 15 21.3 1.65 0.80
1
⁄2 0.840 0.083 0.67 ... 10 15 21.3 2.11 1.00
1
⁄2 0.840 0.095 0.76 ... 30 15 21.3 2.41 1.12
1
⁄2 0.840 0.109 0.85 STD 40 15 21.3 2.77 1.27
1
⁄2 0.840 0.147 1.09 XS 80 15 21.3 3.73 1.62
1
⁄2 0.840 0.188 1.31 ... 160 15 21.3 4.78 1.95
1
⁄2 0.840 0.294 1.72 XXS ... 15 21.3 7.47 2.55
3
⁄4 1.050 0.065 0.69 ... 5 20 26.7 1.65 1.03
3
⁄4 1.050 0.083 0.86 ... 10 20 26.7 2.11 1.28
3
⁄4 1.050 0.095 0.97 ... 30 20 26.7 2.41 1.44
3
⁄4 1.050 0.113 1.13 STD 40 20 26.7 2.87 1.69
3
⁄4 1.050 0.154 1.48 XS 80 20 26.7 3.91 2.20
3
⁄4 1.050 0.219 1.95 ... 160 20 26.7 5.56 2.90
3
⁄4 1.050 0.308 2.44 XXS ... 20 26.7 7.82 3.64

1 1.315 0.065 0.87 ... 5 25 33.4 1.65 1.29

1 1.315 0.109 1.41 ... 10 25 33.4 2.77 2.09
1 1.315 0.114 1.46 ... 30 25 33.4 2.90 2.18
1 1.315 0.133 1.68 STD 40 25 33.4 3.38 2.50
1 1.315 0.179 2.17 XS 80 25 33.4 4.55 3.24
1 1.315 0.250 2.85 ... 160 25 33.4 6.35 4.24
1 1.315 0.358 3.66 XXS ... 25 33.4 9.09 5.45

11⁄4 1.660 0.065 1.11 ... 5 32 42.2 1.65 1.65

11⁄4 1.660 0.109 1.81 ... 10 32 42.2 2.77 2.69
11⁄4 1.660 0.117 1.93 ... 30 32 42.2 2.97 2.87
11⁄4 1.660 0.140 2.27 STD 40 32 42.2 3.56 3.39
11⁄4 1.660 0.191 3.00 XS 80 32 42.2 4.85 4.47
11⁄4 1.660 0.250 3.77 ... 160 32 42.2 6.35 5.61
11⁄4 1.660 0.382 5.22 XXS ... 32 42.2 9.70 7.77

11⁄2 1.900 0.065 1.28 ... 5 40 48.3 1.65 1.90

11⁄2 1.900 0.109 2.09 ... 10 40 48.3 2.77 3.11
11⁄2 1.900 0.125 2.37 ... 30 40 48.3 3.18 3.53
11⁄2 1.900 0.145 2.72 STD 40 40 48.3 3.68 4.05

11⁄2 1.900 0.200 3.63 XS 80 40 48.3 5.08 5.41

11⁄2 1.900 0.281 4.86 ... 160 40 48.3 7.14 7.25
11⁄2 1.900 0.400 6.41 XXS ... 40 48.3 10.15 9.55

3
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

2 2.375 0.065 1.61 ... 5 50 60.3 1.65 2.39

2 2.375 0.083 2.03 ... ... 50 60.3 2.11 3.03
2 2.375 0.109 2.64 ... 10 50 60.3 2.77 3.93
2 2.375 0.125 3.01 ... 30 50 60.3 3.18 4.48

2 2.375 0.141 3.37 ... ... 50 60.3 3.58 5.01

2 2.375 0.154 3.66 STD 40 50 60.3 3.91 5.44
2 2.375 0.172 4.05 ... ... 50 60.3 4.37 6.03
2 2.375 0.188 4.40 ... ... 50 60.3 4.78 6.54
2 2.375 0.218 5.03 XS 80 50 60.3 5.54 7.48
2 2.375 0.250 5.68 ... ... 50 60.3 6.35 8.45
2 2.375 0.281 6.29 ... ... 50 60.3 7.14 9.36
2 2.375 0.344 7.47 ... 160 50 60.3 8.74 11.11
2 2.375 0.436 9.04 XXS ... 50 60.3 11.07 13.44

21⁄2 2.875 0.083 2.48 ... 5 65 73.0 2.11 3.69

21⁄2 2.875 0.109 3.22 ... ... 65 73.0 2.77 4.80
21⁄2 2.875 0.120 3.53 ... 10 65 73.0 3.05 5.26
21⁄2 2.875 0.125 3.67 ... ... 65 73.0 3.18 5.48

21⁄2 2.875 0.141 4.12 ... ... 65 73.0 3.58 6.13

21⁄2 2.875 0.156 4.53 ... ... 65 73.0 3.96 6.74
21⁄2 2.875 0.172 4.97 ... ... 65 73.0 4.37 7.40
21⁄2 2.875 0.188 5.40 ... 30 65 73.0 4.78 8.04
21⁄2 2.875 0.203 5.80 STD 40 65 73.0 5.16 8.63
21⁄2 2.875 0.216 6.14 ... ... 65 73.0 5.49 9.14
21⁄2 2.875 0.250 7.02 ... ... 65 73.0 6.35 10.44
21⁄2 2.875 0.276 7.67 XS 80 65 73.0 7.01 11.41
21⁄2 2.875 0.375 10.02 ... 160 65 73.0 9.53 14.92
21⁄2 2.875 0.552 13.71 XXS ... 65 73.0 14.02 20.39

3 3.500 0.083 3.03 ... 5 80 88.9 2.11 4.52

3 3.500 0.109 3.95 ... ... 80 88.9 2.77 5.88
3 3.500 0.120 4.34 ... 10 80 88.9 3.05 6.46
3 3.500 0.125 4.51 ... ... 80 88.9 3.18 6.72

3 3.500 0.141 5.06 ... ... 80 88.9 3.58 7.53

3 3.500 0.156 5.58 ... ... 80 88.9 3.96 8.30
3 3.500 0.172 6.12 ... ... 80 88.9 4.37 9.11
3 3.500 0.188 6.66 ... 30 80 88.9 4.78 9.92
3 3.500 0.216 7.58 STD 40 80 88.9 5.49 11.29

3 3.500 0.250 8.69 ... ... 80 88.9 6.35 12.93

3 3.500 0.281 9.67 ... ... 80 88.9 7.14 14.40
3 3.500 0.300 10.26 XS 80 80 88.9 7.62 15.27
3 3.500 0.438 14.34 ... 160 80 88.9 11.13 21.35
3 3.500 0.600 18.60 XXS ... 80 88.9 15.24 27.68
31⁄2 4.000 0.083 3.48 ... 5 90 101.6 2.11 5.18
31⁄2 4.000 0.109 4.53 ... ... 90 101.6 2.77 6.75
31⁄2 4.000 0.120 4.98 ... 10 90 101.6 3.05 7.41
31⁄2 4.000 0.125 5.18 ... ... 90 101.6 3.18 7.72

31⁄2 4.000 0.141 5.82 ... ... 90 101.6 3.58 8.65

31⁄2 4.000 0.156 6.41 ... ... 90 101.6 3.96 9.54
31⁄2 4.000 0.172 7.04 ... ... 90 101.6 4.37 10.48
31⁄2 4.000 0.188 7.66 ... 30 90 101.6 4.78 11.41

4
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

31⁄2 4.000 0.226 9.12 STD 40 90 101.6 5.74 13.57

31⁄2 4.000 0.250 10.02 ... ... 90 101.6 6.35 14.92
31⁄2 4.000 0.281 11.17 ... ... 90 101.6 7.14 16.63
31⁄2 4.000 0.318 12.52 XS 80 90 101.6 8.08 18.64

4 4.500 0.083 3.92 ... 5 100 114.3 2.11 5.84

4 4.500 0.109 5.12 ... ... 100 114.3 2.77 7.62
4 4.500 0.120 5.62 ... 10 100 114.3 3.05 8.37
4 4.500 0.125 5.85 ... ... 100 114.3 3.18 8.71
4 4.500 0.141 6.57 ... ... 100 114.3 3.58 9.78
4 4.500 0.156 7.24 ... ... 100 114.3 3.96 10.78
4 4.500 0.172 7.96 ... ... 100 114.3 4.37 11.85
4 4.500 0.188 8.67 ... 30 100 114.3 4.78 12.91
4 4.500 0.203 9.32 ... ... 100 114.3 5.16 13.89
4 4.500 0.219 10.02 ... ... 100 114.3 5.56 14.91
4 4.500 0.237 10.80 STD 40 100 114.3 6.02 16.08
4 4.500 0.250 11.36 ... ... 100 114.3 6.35 16.91

4 4.500 0.281 12.67 ... ... 100 114.3 7.14 18.87

4 4.500 0.312 13.97 ... ... 100 114.3 7.92 20.78
4 4.500 0.337 15.00 XS 80 100 114.3 8.56 22.32
4 4.500 0.438 19.02 ... 120 100 114.3 11.13 28.32
4 4.500 0.531 22.53 ... 160 100 114.3 13.49 33.54
4 4.500 0.674 27.57 XXS ... 100 114.3 17.12 41.03

5 5.563 0.083 4.86 ... ... 125 141.3 2.11 7.24

5 5.563 0.109 6.36 ... 5 125 141.3 2.77 9.46
5 5.563 0.125 7.27 ... ... 125 141.3 3.18 10.83
5 5.563 0.134 7.78 ... 10 125 141.3 3.40 11.56

5 5.563 0.156 9.02 ... ... 125 141.3 3.96 13.41

5 5.563 0.188 10.80 ... ... 125 141.3 4.78 16.09
5 5.563 0.219 12.51 ... ... 125 141.3 5.56 18.61
5 5.563 0.258 14.63 STD 40 125 141.3 6.55 21.77

5 5.563 0.281 15.87 ... ... 125 141.3 7.14 23.62

5 5.563 0.312 17.51 ... ... 125 141.3 7.92 26.05
5 5.563 0.344 19.19 ... ... 125 141.3 8.74 28.57
5 5.563 0.375 20.80 XS 80 125 141.3 9.53 30.97

5 5.563 0.500 27.06 ... 120 125 141.3 12.70 40.28

5 5.563 0.625 32.99 ... 160 125 141.3 15.88 49.12
5 5.563 0.750 38.59 XXS ... 125 141.3 19.05 57.43

6 6.625 0.083 5.80 ... ... 150 168.3 2.11 8.65

6 6.625 0.109 7.59 ... 5 150 168.3 2.77 11.31
6 6.625 0.125 8.69 ... ... 150 168.3 3.18 12.95
6 6.625 0.134 9.30 ... 10 150 168.3 3.40 13.83

6 6.625 0.141 9.77 ... ... 150 168.3 3.58 14.54

6 6.625 0.156 10.79 ... ... 150 168.3 3.96 16.05
6 6.625 0.172 11.87 ... ... 150 168.3 4.37 17.67
6 6.625 0.188 12.94 ... ... 150 168.3 4.78 19.28

6 6.625 0.203 13.94 ... ... 150 168.3 5.16 20.76

6 6.625 0.219 15.00 ... ... 150 168.3 5.56 22.31
6 6.625 0.250 17.04 ... ... 150 168.3 6.35 25.36
6 6.625 0.280 18.99 STD 40 150 168.3 7.11 28.26

5
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

6 6.625 0.312 21.06 ... ... 150 168.3 7.92 31.33

6 6.625 0.344 23.10 ... ... 150 168.3 8.74 34.39
6 6.625 0.375 25.05 ... ... 150 168.3 9.53 37.31
6 6.625 0.432 28.60 XS 80 150 168.3 10.97 42.56

6 6.625 0.500 32.74 ... ... 150 168.3 12.70 48.73

6 6.625 0.562 36.43 ... 120 150 168.3 14.27 54.21
6 6.625 0.625 40.09 ... ... 150 168.3 15.88 59.69

6 6.625 0.719 45.39 ... 160 150 168.3 18.26 67.57

6 6.625 0.750 47.10 ... ... 150 168.3 19.05 70.12
6 6.625 0.864 53.21 XXS ... 150 168.3 21.95 79.22
6 6.625 0.875 53.78 ... ... 150 168.3 22.23 80.08

8 8.625 0.109 9.92 ... 5 200 219.1 2.77 14.78

8 8.625 0.125 11.36 ... ... 200 219.1 3.18 16.93
8 8.625 0.148 13.41 ... 10 200 219.1 3.76 19.97
8 8.625 0.156 14.12 ... ... 200 219.1 3.96 21.01

8 8.625 0.188 16.96 ... ... 200 219.1 4.78 25.26

8 8.625 0.203 18.28 ... ... 200 219.1 5.16 27.22
8 8.625 0.219 19.68 ... ... 200 219.1 5.56 29.28
8 8.625 0.250 22.38 ... 20 200 219.1 6.35 33.32
8 8.625 0.277 24.72 ... 30 200 219.1 7.04 36.82
8 8.625 0.312 27.73 ... ... 200 219.1 7.92 41.25
8 8.625 0.322 28.58 STD 40 200 219.1 8.18 42.55
8 8.625 0.344 30.45 ... ... 200 219.1 8.74 45.34

8 8.625 0.375 33.07 ... ... 200 219.1 9.53 49.25

8 8.625 0.406 35.67 ... 60 200 219.1 10.31 53.09
8 8.625 0.438 38.33 ... ... 200 219.1 11.13 57.08
8 8.625 0.500 43.43 XS 80 200 219.1 12.70 64.64

8 8.625 0.562 48.44 ... ... 200 219.1 14.27 72.08

8 8.625 0.594 51.00 ... 100 200 219.1 15.09 75.92
8 8.625 0.625 53.45 ... ... 200 219.1 15.88 79.59
8 8.625 0.719 60.77 ... 120 200 219.1 18.26 90.44

8 8.625 0.750 63.14 ... ... 200 219.1 19.05 93.98

8 8.625 0.812 67.82 ... 140 200 219.1 20.62 100.93
8 8.625 0.875 72.49 XXS ... 200 219.1 22.23 107.93
8 8.625 0.906 74.76 ... 160 200 219.1 23.01 111.27
8 8.625 1.000 81.51 ... ... 200 219.1 25.40 121.33

10 10.750 0.134 15.21 ... 5 250 273.0 3.40 22.61

10 10.750 0.156 17.67 ... ... 250 273.0 3.96 26.27
10 10.750 0.165 18.67 ... 10 250 273.0 4.19 27.78
10 10.750 0.188 21.23 ... ... 250 273.0 4.78 31.62

10 10.750 0.203 22.89 ... ... 250 273.0 5.16 34.08

10 10.750 0.219 24.65 ... ... 250 273.0 5.56 36.67
10 10.750 0.250 28.06 ... 20 250 273.0 6.35 41.76
10 10.750 0.279 31.23 ... ... 250 273.0 7.09 46.49

10 10.750 0.307 34.27 ... 30 250 273.0 7.80 51.01

10 10.750 0.344 38.27 ... ... 250 273.0 8.74 56.96
10 10.750 0.365 40.52 STD 40 250 273.0 9.27 60.29
10 10.750 0.438 48.28 ... ... 250 273.0 11.13 71.88

6
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

10 10.750 0.500 54.79 XS 60 250 273.0 12.70 81.53

10 10.750 0.562 61.21 ... ... 250 273.0 14.27 91.05
10 10.750 0.594 64.49 ... 80 250 273.0 15.09 95.98
10 10.750 0.625 67.65 ... ... 250 273.0 15.88 100.69

10 10.750 0.719 77.10 ... 100 250 273.0 18.26 114.71

10 10.750 0.812 86.26 ... ... 250 273.0 20.62 128.34
10 10.750 0.844 89.38 ... 120 250 273.0 21.44 133.01
10 10.750 0.875 92.37 ... ... 250 273.0 22.23 137.48
10 10.750 0.938 98.39 ... ... 250 273.0 23.83 146.43
10 10.750 1.000 104.23 XXS 140 250 273.0 25.40 155.10
10 10.750 1.125 115.75 ... 160 250 273.0 28.58 172.27
10 10.750 1.250 126.94 ... ... 250 273.0 31.75 188.90
12 12.750 0.156 21.00 ... 5 300 323.8 3.96 31.24
12 12.750 0.172 23.13 ... ... 300 323.8 4.37 34.43
12 12.750 0.180 24.19 ... 10 300 323.8 4.57 35.98
12 12.750 0.188 25.25 ... ... 300 323.8 4.78 37.61

12 12.750 0.203 27.23 ... ... 300 323.8 5.16 40.55

12 12.750 0.219 29.34 ... ... 300 323.8 5.56 43.64
12 12.750 0.250 33.41 ... 20 300 323.8 6.35 49.71
12 12.750 0.281 37.46 ... ... 300 323.8 7.14 55.76
12 12.750 0.312 41.48 ... ... 300 323.8 7.92 61.70
12 12.750 0.330 43.81 ... 30 300 323.8 8.38 65.19
12 12.750 0.344 45.62 ... ... 300 323.8 8.74 67.91
12 12.750 0.375 49.61 STD ... 300 323.8 9.53 73.86

12 12.750 0.406 53.57 ... 40 300 323.8 10.31 79.71

12 12.750 0.438 57.65 ... ... 300 323.8 11.13 85.82
12 12.750 0.500 65.48 XS ... 300 323.8 12.70 97.44
12 12.750 0.562 73.22 ... 60 300 323.8 14.27 108.93

12 12.750 0.625 81.01 ... ... 300 323.8 15.88 120.59

12 12.750 0.688 88.71 ... 80 300 323.8 17.48 132.05
12 12.750 0.750 96.21 ... ... 300 323.8 19.05 143.17
12 12.750 0.812 103.63 ... ... 300 323.8 20.62 154.17

12 12.750 0.844 107.42 ... 100 300 323.8 21.44 159.87

12 12.750 0.875 111.08 ... ... 300 323.8 22.23 165.33
12 12.750 0.938 118.44 ... ... 300 323.8 23.83 176.29
12 12.750 1.000 125.61 XXS 120 300 323.8 25.40 186.92

12 12.750 1.062 132.69 ... ... 300 323.8 26.97 197.43

12 12.750 1.125 139.81 ... 140 300 323.8 28.58 208.08
12 12.750 1.250 153.67 ... ... 300 323.8 31.75 228.68
12 12.750 1.312 160.42 ... 160 300 323.8 33.32 238.69

14 14.000 0.156 23.09 ... 5 350 355.6 3.96 34.34

14 14.000 0.188 27.76 ... ... 350 355.6 4.78 41.36
14 14.000 0.203 29.94 ... ... 350 355.6 5.16 44.59
14 14.000 0.210 30.96 ... ... 350 355.6 5.33 46.04

14 14.000 0.219 32.26 ... ... 350 355.6 5.56 48.00

14 14.000 0.250 36.75 ... 10 350 355.6 6.35 54.69
14 14.000 0.281 41.21 ... ... 350 355.6 7.14 61.36
14 14.000 0.312 45.65 ... 20 350 355.6 7.92 67.91

7
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

14 14.000 0.344 50.22 ... ... 350 355.6 8.74 74.76

14 14.000 0.375 54.62 STD 30 350 355.6 9.53 81.33
14 14.000 0.406 59.00 ... ... 350 355.6 10.31 87.79
14 14.000 0.438 63.50 ... 40 350 355.6 11.13 94.55

14 14.000 0.469 67.84 ... ... 350 355.6 11.91 100.95

14 14.000 0.500 72.16 XS ... 350 355.6 12.70 107.40
14 14.000 0.562 80.73 ... ... 350 355.6 14.27 120.12
14 14.000 0.594 85.13 ... 60 350 355.6 15.09 126.72
14 14.000 0.625 89.36 ... ... 350 355.6 15.88 133.04
14 14.000 0.688 97.91 ... ... 350 355.6 17.48 145.76
14 14.000 0.750 106.23 ... 80 350 355.6 19.05 158.11
14 14.000 0.812 114.48 ... ... 350 355.6 20.62 170.34

14 14.000 0.875 122.77 ... ... 350 355.6 22.23 182.76

14 14.000 0.938 130.98 ... 100 350 355.6 23.83 194.98
14 14.000 1.000 138.97 ... ... 350 355.6 25.40 206.84
14 14.000 1.062 146.88 ... ... 350 355.6 26.97 218.58

14 14.000 1.094 150.93 ... 120 350 355.6 27.79 224.66

14 14.000 1.125 154.84 ... ... 350 355.6 28.58 230.49
14 14.000 1.250 170.37 ... 140 350 355.6 31.75 253.58
14 14.000 1.406 189.29 ... 160 350 355.6 35.71 281.72

14 14.000 2.000 256.56 ... ... 350 355.6 50.80 381.85

14 14.000 2.125 269.76 ... ... 350 355.6 53.98 401.52
14 14.000 2.200 277.51 ... ... 350 355.6 55.88 413.04
14 14.000 2.500 307.34 ... ... 350 355.6 63.50 457.43
16 16.000 0.165 27.93 ... 5 400 406.4 4.19 41.56
16 16.000 0.188 31.78 ... ... 400 406.4 4.78 47.34
16 16.000 0.203 34.28 ... ... 400 406.4 5.16 51.06
16 16.000 0.219 36.95 ... ... 400 406.4 5.56 54.96

16 16.000 0.250 42.09 ... 10 400 406.4 6.35 62.65

16 16.000 0.281 47.22 ... ... 400 406.4 7.14 70.30
16 16.000 0.312 52.32 ... 20 400 406.4 7.92 77.83
16 16.000 0.344 57.57 ... ... 400 406.4 8.74 85.71

16 16.000 0.375 62.64 STD 30 400 406.4 9.53 93.27

16 16.000 0.406 67.68 ... ... 400 406.4 10.31 100.71
16 16.000 0.438 72.86 ... ... 400 406.4 11.13 108.49
16 16.000 0.469 77.87 ... ... 400 406.4 11.91 115.87

16 16.000 0.500 82.85 XS 40 400 406.4 12.70 123.31

16 16.000 0.562 92.75 ... ... 400 406.4 14.27 138.00
16 16.000 0.625 102.72 ... ... 400 406.4 15.88 152.94
16 16.000 0.656 107.60 ... 60 400 406.4 16.66 160.13

16 16.000 0.688 112.62 ... ... 400 406.4 17.48 167.66

16 16.000 0.750 122.27 ... ... 400 406.4 19.05 181.98
16 16.000 0.812 131.84 ... ... 400 406.4 20.62 196.18
16 16.000 0.844 136.74 ... 80 400 406.4 21.44 203.54

16 16.000 0.875 141.48 ... ... 400 406.4 22.23 210.61

16 16.000 0.938 151.03 ... ... 400 406.4 23.83 224.83
16 16.000 1.000 160.35 ... ... 400 406.4 25.40 238.66
16 16.000 1.031 164.98 ... 100 400 406.4 26.19 245.57

8
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

16 16.000 1.062 169.59 ... ... 400 406.4 26.97 252.37

16 16.000 1.125 178.89 ... ... 400 406.4 28.58 266.30
16 16.000 1.188 188.11 ... ... 400 406.4 30.18 280.01
16 16.000 1.219 192.61 ... 120 400 406.4 30.96 286.66

16 16.000 1.250 197.10 ... ... 400 406.4 31.75 293.35

16 16.000 1.438 223.85 ... 140 400 406.4 36.53 333.21
16 16.000 1.594 245.48 ... 160 400 406.4 40.49 365.38

18 18.000 0.165 31.46 ... 5 450 457 4.19 46.79

18 18.000 0.188 35.80 ... ... 450 457 4.78 53.31
18 18.000 0.219 41.63 ... ... 450 457 5.56 61.90
18 18.000 0.250 47.44 ... 10 450 457 6.35 70.57

18 18.000 0.281 53.23 ... ... 450 457 7.14 79.21

18 18.000 0.312 58.99 ... 20 450 457 7.92 87.71
18 18.000 0.344 64.93 ... ... 450 457 8.74 96.62
18 18.000 0.375 70.65 STD ... 450 457 9.53 105.17

18 18.000 0.406 76.36 ... ... 450 457 10.31 113.58

18 18.000 0.438 82.23 ... 30 450 457 11.13 122.38
18 18.000 0.469 87.89 ... ... 450 457 11.91 130.73
18 18.000 0.500 93.54 XS ... 450 457 12.70 139.16
18 18.000 0.562 104.76 ... 40 450 457 14.27 155.81
18 18.000 0.625 116.09 ... ... 450 457 15.88 172.75
18 18.000 0.688 127.32 ... ... 450 457 17.48 189.47
18 18.000 0.750 138.30 ... 60 450 457 19.05 205.75

18 18.000 0.812 149.20 ... ... 450 457 20.62 221.91

18 18.000 0.875 160.18 ... ... 450 457 22.23 238.35
18 18.000 0.938 171.08 ... 80 450 457 23.83 254.57
18 18.000 1.000 181.73 ... ... 450 457 25.40 270.36

18 18.000 1.062 192.29 ... ... 450 457 26.97 286.02

18 18.000 1.125 202.94 ... ... 450 457 28.58 301.96
18 18.000 1.156 208.15 ... 100 450 457 29.36 309.64
18 18.000 1.188 213.51 ... ... 450 457 30.18 317.68

18 18.000 1.250 223.82 ... ... 450 457 31.75 332.97

18 18.000 1.375 244.37 ... 120 450 457 34.93 363.58
18 18.000 1.562 274.48 ... 140 450 457 39.67 408.28
18 18.000 1.781 308.79 ... 160 450 457 45.24 459.39
20 20.000 0.188 39.82 ... 5 500 508 4.78 59.32
20 20.000 0.219 46.31 ... ... 500 508 5.56 68.89
20 20.000 0.250 52.78 ... 10 500 508 6.35 78.56
20 20.000 0.281 59.23 ... ... 500 508 7.14 88.19
20 20.000 0.312 65.66 ... ... 500 508 7.92 97.68
20 20.000 0.344 72.28 ... ... 500 508 8.74 107.61
20 20.000 0.375 78.67 STD 20 500 508 9.53 117.15
20 20.000 0.406 85.04 ... ... 500 508 10.31 126.54

20 20.000 0.438 91.59 ... ... 500 508 11.13 136.38

20 20.000 0.469 97.92 ... ... 500 508 11.91 145.71
20 20.000 0.500 104.23 XS 30 500 508 12.70 155.13
20 20.000 0.562 116.78 ... ... 500 508 14.27 173.75

9
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

20 20.000 0.594 123.23 ... 40 500 508 15.09 183.43

20 20.000 0.625 129.45 ... ... 500 508 15.88 192.73
20 20.000 0.688 142.03 ... ... 500 508 17.48 211.45
20 20.000 0.750 154.34 ... ... 500 508 19.05 229.71

20 20.000 0.812 166.56 ... 60 500 508 20.62 247.84

20 20.000 0.875 178.89 ... ... 500 508 22.23 266.31
20 20.000 0.938 191.14 ... ... 500 508 23.83 284.54
20 20.000 1.000 203.11 ... ... 500 508 25.40 302.30
20 20.000 1.031 209.06 ... 80 500 508 26.19 311.19
20 20.000 1.062 215.00 ... ... 500 508 26.97 319.94
20 20.000 1.125 227.00 ... ... 500 508 28.58 337.91
20 20.000 1.188 238.91 ... ... 500 508 30.18 355.63
20 20.000 1.250 250.55 ... ... 500 508 31.75 372.91
20 20.000 1.281 256.34 ... 100 500 508 32.54 381.55
20 20.000 1.312 262.10 ... ... 500 508 33.32 390.05
20 20.000 1.375 273.76 ... ... 500 508 34.93 407.51

20 20.000 1.500 296.65 ... 120 500 508 38.10 441.52

20 20.000 1.750 341.41 ... 140 500 508 44.45 508.15
20 20.000 1.969 379.53 ... 160 500 508 50.01 564.85
22 22.000 0.188 43.84 ... 5 550 559 4.78 65.33
22 22.000 0.219 50.99 ... ... 550 559 5.56 75.89
22 22.000 0.250 58.13 ... 10 550 559 6.35 86.55
22 22.000 0.281 65.24 ... ... 550 559 7.14 97.17

22 22.000 0.312 72.34 ... ... 550 559 7.92 107.64

22 22.000 0.344 79.64 ... ... 550 559 8.74 118.60
22 22.000 0.375 86.69 STD 20 550 559 9.53 129.14
22 22.000 0.406 93.72 ... ... 550 559 10.31 139.51

22 22.000 0.438 100.96 ... ... 550 559 11.13 150.38

22 22.000 0.469 107.95 ... ... 550 559 11.91 160.69
22 22.000 0.500 114.92 XS 30 550 559 12.70 171.10
22 22.000 0.562 128.79 ... ... 550 559 14.27 191.70

22 22.000 0.625 142.81 ... ... 550 559 15.88 212.70

22 22.000 0.688 156.74 ... ... 550 559 17.48 233.44
22 22.000 0.750 170.37 ... ... 550 559 19.05 253.67
22 22.000 0.812 183.92 ... ... 550 559 20.62 273.78
22 22.000 0.875 197.60 ... 60 550 559 22.23 294.27
22 22.000 0.938 211.19 ... ... 550 559 23.83 314.51
22 22.000 1.000 224.49 ... ... 550 559 25.40 334.25
22 22.000 1.062 237.70 ... ... 550 559 26.97 353.86
22 22.000 1.125 251.05 ... 80 550 559 28.58 373.85

22 22.000 1.188 264.31 ... ... 550 559 30.18 393.59

22 22.000 1.250 277.27 ... ... 550 559 31.75 412.84
22 22.000 1.312 290.15 ... ... 550 559 33.32 431.96
22 22.000 1.375 303.16 ... 100 550 559 34.93 451.45
22 22.000 1.438 316.08 ... ... 550 559 36.53 470.69

22 22.000 1.500 328.72 ... ... 550 559 38.10 489.44

22 22.000 1.625 353.94 ... 120 550 559 41.28 527.05
22 22.000 1.875 403.38 ... 140 550 559 47.63 600.67
22 22.000 2.125 451.49 ... 160 550 559 53.98 672.30

10
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

24 24.000 0.218 55.42 ... 5 600 610 5.54 82.58

24 24.000 0.250 63.47 ... 10 600 610 6.35 94.53
24 24.000 0.281 71.25 ... ... 600 610 7.14 106.15
24 24.000 0.312 79.01 ... ... 600 610 7.92 117.60

24 24.000 0.344 86.99 ... ... 600 610 8.74 129.60

24 24.000 0.375 94.71 STD 20 600 610 9.53 141.12
24 24.000 0.406 102.40 ... ... 600 610 10.31 152.48
24 24.000 0.438 110.32 ... ... 600 610 11.13 164.38
24 24.000 0.469 117.98 ... ... 600 610 11.91 175.67
24 24.000 0.500 125.61 XS ... 600 610 12.70 187.07
24 24.000 0.562 140.81 ... 30 600 610 14.27 209.65
24 24.000 0.625 156.17 ... ... 600 610 15.88 232.67
24 24.000 0.688 171.45 ... 40 600 610 17.48 255.43
24 24.000 0.750 186.41 ... ... 600 610 19.05 277.63
24 24.000 0.812 201.28 ... ... 600 610 20.62 299.71
24 24.000 0.875 216.31 ... ... 600 610 22.23 322.23

24 24.000 0.938 231.25 ... ... 600 610 23.83 344.48

24 24.000 0.969 238.57 ... 60 600 610 24.61 355.28
24 24.000 1.000 245.87 ... ... 600 610 25.40 366.19
24 24.000 1.062 260.41 ... ... 600 610 26.97 387.79
24 24.000 1.125 275.10 ... ... 600 610 28.58 409.80
24 24.000 1.188 289.71 ... ... 600 610 30.18 431.55
24 24.000 1.219 296.86 ... 80 600 610 30.96 442.11
24 24.000 1.250 304.00 ... ... 600 610 31.75 452.77

24 24.000 1.312 318.21 ... ... 600 610 33.32 473.87

24 24.000 1.375 332.56 ... ... 600 610 34.93 495.38
24 24.000 1.438 346.83 ... ... 600 610 36.53 516.63
24 24.000 1.500 360.79 ... ... 600 610 38.10 537.36

24 24.000 1.531 367.74 ... 100 600 610 38.89 547.74

24 24.000 1.562 374.66 ... ... 600 610 39.67 557.97
24 24.000 1.812 429.79 ... 120 600 610 46.02 640.07
24 24.000 2.062 483.57 ... 140 600 610 52.37 720.19
24 24.000 2.344 542.64 ... 160 600 610 59.54 808.27
26 26.000 0.250 68.82 ... ... 650 660 6.35 102.36
26 26.000 0.281 77.26 ... ... 650 660 7.14 114.96
26 26.000 0.312 85.68 ... 10 650 660 7.92 127.36
26 26.000 0.344 94.35 ... ... 650 660 8.74 140.37

26 26.000 0.375 102.72 STD ... 650 660 9.53 152.88

26 26.000 0.406 111.08 ... ... 650 660 10.31 165.19
26 26.000 0.438 119.69 ... ... 650 660 11.13 178.10
26 26.000 0.469 128.00 ... ... 650 660 11.91 190.36
26 26.000 0.500 136.30 XS 20 650 660 12.70 202.74
26 26.000 0.562 152.83 ... ... 650 660 14.27 227.25
26 26.000 0.625 169.54 ... ... 650 660 15.88 252.25
26 26.000 0.688 186.16 ... ... 650 660 17.48 276.98

26 26.000 0.750 202.44 ... ... 650 660 19.05 301.12

26 26.000 0.812 218.64 ... ... 650 660 20.62 325.14
26 26.000 0.875 235.01 ... ... 650 660 22.23 349.64
26 26.000 0.938 251.30 ... ... 650 660 23.83 373.87
26 26.000 1.000 267.25 ... ... 650 660 25.40 397.51

11
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

28 28.000 0.250 74.16 ... ... 700 711 6.35 110.35

28 28.000 0.281 83.26 ... ... 700 711 7.14 123.94
28 28.000 0.312 92.35 ... 10 700 711 7.92 137.32
28 28.000 0.344 101.70 ... ... 700 711 8.74 151.37

28 28.000 0.375 110.74 STD ... 700 711 9.53 164.86

28 28.000 0.406 119.76 ... ... 700 711 10.31 178.16
28 28.000 0.438 129.05 ... ... 700 711 11.13 192.10
28 28.000 0.469 138.03 ... ... 700 711 11.91 205.34
28 28.000 0.500 146.99 XS 20 700 711 12.70 218.71
28 28.000 0.562 164.84 ... ... 700 711 14.27 245.19
28 28.000 0.625 182.90 ... 30 700 711 15.88 272.23
28 28.000 0.688 200.87 ... ... 700 711 17.48 298.96
28 28.000 0.750 218.48 ... ... 700 711 19.05 325.08
28 28.000 0.812 236.00 ... ... 700 711 20.62 351.07
28 28.000 0.875 253.72 ... ... 700 711 22.23 377.60
28 28.000 0.938 271.36 ... ... 700 711 23.83 403.84
28 28.000 1.000 288.63 ... ... 700 711 25.40 429.46

30 30.000 0.250 79.51 ... 5 750 762 6.35 118.34

30 30.000 0.281 89.27 ... ... 750 762 7.14 132.92
30 30.000 0.312 99.02 ... 10 750 762 7.92 147.29
30 30.000 0.344 109.06 ... ... 750 762 8.74 162.36
30 30.000 0.375 118.76 STD ... 750 762 9.53 176.85
30 30.000 0.406 128.44 ... ... 750 762 10.31 191.12
30 30.000 0.438 138.42 ... ... 750 762 11.13 206.10
30 30.000 0.469 148.06 ... ... 750 762 11.91 220.32
30 30.000 0.500 157.68 XS 20 750 762 12.70 234.68
30 30.000 0.562 176.86 ... ... 750 762 14.27 263.14
30 30.000 0.625 196.26 ... 30 750 762 15.88 292.20
30 30.000 0.688 215.58 ... ... 750 762 17.48 320.95

30 30.000 0.750 234.51 ... ... 750 762 19.05 349.04

30 30.000 0.812 253.36 ... ... 750 762 20.62 377.01
30 30.000 0.875 272.43 ... ... 750 762 22.23 405.56
30 30.000 0.938 291.41 ... ... 750 762 23.83 433.81
30 30.000 1.000 310.01 ... ... 750 762 25.40 461.41
30 30.000 1.062 328.53 ... ... 750 762 26.97 488.88
30 30.000 1.125 347.26 ... ... 750 762 28.58 516.93
30 30.000 1.188 365.90 ... ... 750 762 30.18 544.68
30 30.000 1.250 384.17 ... ... 750 762 31.75 571.79

32 32.000 0.250 84.85 ... ... 800 813 6.35 126.32

32 32.000 0.281 95.28 ... ... 800 813 7.14 141.90
32 32.000 0.312 105.69 ... 10 800 813 7.92 157.25
32 32.000 0.344 116.41 ... ... 800 813 8.74 173.35

32 32.000 0.375 126.78 STD ... 800 813 9.53 188.83

32 32.000 0.406 137.12 ... ... 800 813 10.31 204.09
32 32.000 0.438 147.78 ... ... 800 813 11.13 220.10
32 32.000 0.469 158.08 ... ... 800 813 11.91 235.29

32 32.000 0.500 168.37 XS 20 800 813 12.70 250.65

32 32.000 0.562 188.87 ... ... 800 813 14.27 281.09
32 32.000 0.625 209.62 ... 30 800 813 15.88 312.17
32 32.000 0.688 230.29 ... 40 800 813 17.48 342.94

12
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

32 32.000 0.750 250.55 ... ... 800 813 19.05 373.00

32 32.000 0.812 270.72 ... ... 800 813 20.62 402.94
32 32.000 0.875 291.14 ... ... 800 813 22.23 433.52
32 32.000 0.938 311.47 ... ... 800 813 23.83 463.78

32 32.000 1.000 331.39 ... ... 800 813 25.40 493.35

32 32.000 1.062 351.23 ... ... 800 813 26.97 522.80
32 32.000 1.125 371.31 ... ... 800 813 28.58 552.88
32 32.000 1.188 391.30 ... ... 800 813 30.18 582.64
32 32.000 1.250 410.90 ... ... 800 813 31.75 611.72

34 34.000 0.250 90.20 ... ... 850 864 6.35 134.31

34 34.000 0.281 101.29 ... ... 850 864 7.14 150.88
34 34.000 0.312 112.36 ... 10 850 864 7.92 167.21
34 34.000 0.344 123.77 ... ... 850 864 8.74 184.34

34 34.000 0.375 134.79 STD ... 850 864 9.53 200.82

34 34.000 0.406 145.80 ... ... 850 864 10.31 217.06
34 34.000 0.438 157.14 ... ... 850 864 11.13 234.10
34 34.000 0.469 168.11 ... ... 850 864 11.91 250.27

34 34.000 0.500 179.06 XS 20 850 864 12.70 266.63

34 34.000 0.562 200.89 ... ... 850 864 14.27 299.04
34 34.000 0.625 222.99 ... 30 850 864 15.88 332.14
34 34.000 0.688 245.00 ... 40 850 864 17.48 364.92
34 34.000 0.750 266.58 ... ... 850 864 19.05 396.96
34 34.000 0.812 288.08 ... ... 850 864 20.62 428.88
34 34.000 0.875 309.84 ... ... 850 864 22.23 461.48
34 34.000 0.938 331.52 ... ... 850 864 23.83 493.75
34 34.000 1.000 352.77 ... ... 850 864 25.40 525.30
34 34.000 1.062 373.94 ... ... 850 864 26.97 556.73
34 34.000 1.125 395.36 ... ... 850 864 28.58 588.83
34 34.000 1.188 416.70 ... ... 850 864 30.18 620.60
34 34.000 1.250 437.62 ... ... 850 864 31.75 651.65

36 36.000 0.250 95.54 ... ... 900 914 6.35 142.14

36 36.000 0.281 107.30 ... ... 900 914 7.14 159.68
36 36.000 0.312 119.03 ... 10 900 914 7.92 176.97
36 36.000 0.344 131.12 ... ... 900 914 8.74 195.12

36 36.000 0.375 142.81 STD ... 900 914 9.53 212.57

36 36.000 0.406 154.48 ... ... 900 914 10.31 229.77
36 36.000 0.438 166.51 ... ... 900 914 11.13 247.82
36 36.000 0.469 178.14 ... ... 900 914 11.91 264.96

36 36.000 0.500 189.75 XS 20 900 914 12.70 282.29

36 36.000 0.562 212.90 ... ... 900 914 14.27 316.63
36 36.000 0.625 236.35 ... 30 900 914 15.88 351.73
36 36.000 0.688 259.71 ... ... 900 914 17.48 386.47

36 36.000 0.750 282.62 ... 40 900 914 19.05 420.45

36 36.000 0.812 305.44 ... ... 900 914 20.62 454.30
36 36.000 0.875 328.55 ... ... 900 914 22.23 488.89
36 36.000 0.938 351.57 ... ... 900 914 23.83 523.14

13
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

36 36.000 1.000 374.15 ... ... 900 914 25.40 556.62

36 36.000 1.062 396.64 ... ... 900 914 26.97 589.98
36 36.000 1.125 419.42 ... ... 900 914 28.58 624.07
36 36.000 1.188 442.10 ... ... 900 914 30.18 657.81
36 36.000 1.250 464.35 ... ... 900 914 31.75 690.80
38 38.000 0.312 125.70 ... ... 950 965 7.92 186.94
38 38.000 0.344 138.47 ... ... 950 965 8.74 206.11
38 38.000 0.375 150.83 STD ... 950 965 9.53 224.56
38 38.000 0.406 163.16 ... ... 950 965 10.31 242.74

38 38.000 0.438 175.87 ... ... 950 965 11.13 261.82

38 38.000 0.469 188.17 ... ... 950 965 11.91 279.94
38 38.000 0.500 200.44 XS ... 950 965 12.70 298.26
38 38.000 0.562 224.92 ... ... 950 965 14.27 334.58

38 38.000 0.625 249.71 ... ... 950 965 15.88 371.70

38 38.000 0.688 274.42 ... ... 950 965 17.48 408.46
38 38.000 0.750 298.65 ... ... 950 965 19.05 444.41
38 38.000 0.812 322.80 ... ... 950 965 20.62 480.24

38 38.000 0.875 347.26 ... ... 950 965 22.23 516.85

38 38.000 0.938 371.63 ... ... 950 965 23.83 553.11
38 38.000 1.000 395.53 ... ... 950 965 25.40 588.57
38 38.000 1.062 419.35 ... ... 950 965 26.97 623.90
38 38.000 1.125 443.47 ... ... 950 965 28.58 660.01
38 38.000 1.188 467.50 ... ... 950 965 30.18 695.77
38 38.000 1.250 491.07 ... ... 950 965 31.75 730.74

40 40.000 0.312 132.37 ... ... 1 000 1 016 7.92 196.90

40 40.000 0.344 145.83 ... ... 1 000 1 016 8.74 217.11
40 40.000 0.375 158.85 STD ... 1 000 1 016 9.53 236.54
40 40.000 0.406 171.84 ... ... 1 000 1 016 10.31 255.71

40 40.000 0.438 185.24 ... ... 1 000 1 016 11.13 275.82

40 40.000 0.469 198.19 ... ... 1 000 1 016 11.91 294.92
40 40.000 0.500 211.13 XS ... 1 000 1 016 12.70 314.23
40 40.000 0.562 236.93 ... ... 1 000 1 016 14.27 352.53

40 40.000 0.625 263.07 ... ... 1 000 1 016 15.88 391.67

40 40.000 0.688 289.13 ... ... 1 000 1 016 17.48 430.45
40 40.000 0.750 314.69 ... ... 1 000 1 016 19.05 468.37
40 40.000 0.812 340.16 ... ... 1 000 1 016 20.62 506.17

40 40.000 0.875 365.97 ... ... 1 000 1 016 22.23 544.81

40 40.000 0.938 391.68 ... ... 1 000 1 016 23.83 583.08
40 40.000 1.000 416.91 ... ... 1 000 1 016 25.40 620.51
40 40.000 1.062 442.05 ... ... 1 000 1 016 26.97 657.82

40 40.000 1.125 467.52 ... ... 1 000 1 016 28.58 695.96

40 40.000 1.188 492.90 ... ... 1 000 1 016 30.18 733.73
40 40.000 1.250 517.80 ... ... 1 000 1 016 31.75 770.67

42 42.000 0.344 153.18 ... ... 1 050 1 067 8.74 228.10

42 42.000 0.375 166.86 STD ... 1 050 1 067 9.53 248.53
42 42.000 0.406 180.52 ... ... 1 050 1 067 10.31 268.67
42 42.000 0.438 194.60 ... ... 1 050 1 067 11.13 289.82

14
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

42 42.000 0.469 208.22 ... ... 1 050 1 067 11.91 309.90

42 42.000 0.500 221.82 XS ... 1 050 1 067 12.70 330.21
42 42.000 0.562 248.95 ... ... 1 050 1 067 14.27 370.48
42 42.000 0.625 276.44 ... ... 1 050 1 067 15.88 411.64

42 42.000 0.688 303.84 ... ... 1 050 1 067 17.48 452.43

42 42.000 0.750 330.72 ... ... 1 050 1 067 19.05 492.33
42 42.000 0.812 357.52 ... ... 1 050 1 067 20.62 532.11
42 42.000 0.875 384.67 ... ... 1 050 1 067 22.23 572.77
42 42.000 0.938 411.74 ... ... 1 050 1 067 23.83 613.05
42 42.000 1.000 438.29 ... ... 1 050 1 067 25.40 652.46
42 42.000 1.062 464.76 ... ... 1 050 1 067 26.97 691.75
42 42.000 1.125 491.57 ... ... 1 050 1 067 28.58 731.91
42 42.000 1.188 518.30 ... ... 1 050 1 067 30.18 771.69
42 42.000 1.250 544.52 ... ... 1 050 1 067 31.75 810.60
44 44.000 0.344 160.54 ... ... 1 100 1 118 8.74 239.09
44 44.000 0.375 174.88 STD ... 1 100 1 118 9.53 260.52
44 44.000 0.406 189.20 ... ... 1 100 1 118 10.31 281.64
44 44.000 0.438 203.97 ... ... 1 100 1 118 11.13 303.82
44 44.000 0.469 218.25 ... ... 1 100 1 118 11.91 324.88
44 44.000 0.500 232.51 XS ... 1 100 1 118 12.70 346.18
44 44.000 0.562 260.97 ... ... 1 100 1 118 14.27 388.42
44 44.000 0.625 289.80 ... ... 1 100 1 118 15.88 431.62

44 44.000 0.688 318.55 ... ... 1 100 1 118 17.48 474.42

44 44.000 0.750 346.76 ... ... 1 100 1 118 19.05 516.29
44 44.000 0.812 374.88 ... ... 1 100 1 118 20.62 558.04
44 44.000 0.875 403.38 ... ... 1 100 1 118 22.23 600.73
44 44.000 0.938 431.79 ... ... 1 100 1 118 23.83 643.03

44 44.000 1.000 459.67 ... ... 1 100 1 118 25.40 684.41

44 44.000 1.062 487.47 ... ... 1 100 1 118 26.97 725.67
44 44.000 1.125 515.63 ... ... 1 100 1 118 28.58 767.85
44 44.000 1.188 543.70 ... ... 1 100 1 118 30.18 809.65
44 44.000 1.250 571.25 ... ... 1 100 1 118 31.75 850.54

46 46.000 0.344 167.89 ... ... 1 150 1 168 8.74 249.87

46 46.000 0.375 182.90 STD ... 1 150 1 168 9.53 272.27
46 46.000 0.406 197.88 ... ... 1 150 1 168 10.31 294.35
46 46.000 0.438 213.33 ... ... 1 150 1 168 11.13 317.54

46 46.000 0.469 228.27 ... ... 1 150 1 168 11.91 339.56

46 46.000 0.500 243.20 XS ... 1 150 1 168 12.70 361.84
46 46.000 0.562 272.98 ... ... 1 150 1 168 14.27 406.02
46 46.000 0.625 303.16 ... ... 1 150 1 168 15.88 451.20

46 46.000 0.688 333.26 ... ... 1 150 1 168 17.48 495.97

46 46.000 0.750 362.79 ... ... 1 150 1 168 19.05 539.78
46 46.000 0.812 392.24 ... ... 1 150 1 168 20.62 583.47
46 46.000 0.875 422.09 ... ... 1 150 1 168 22.23 628.14
46 46.000 0.938 451.85 ... ... 1 150 1 168 23.83 672.41

46 46.000 1.000 481.05 ... ... 1 150 1 168 25.40 715.73

46 46.000 1.062 510.17 ... ... 1 150 1 168 26.97 758.92
46 46.000 1.125 539.68 ... ... 1 150 1 168 28.58 803.09
46 46.000 1.188 569.10 ... ... 1 150 1 168 30.18 846.86
46 46.000 1.250 597.97 ... ... 1 150 1 168 31.75 889.69

15
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

48 48.000 0.344 175.25 ... ... 1 200 1 219 8.74 260.86

48 48.000 0.375 190.92 STD ... 1 200 1 219 9.53 284.25
48 48.000 0.406 206.56 ... ... 1 200 1 219 10.31 307.32
48 48.000 0.438 222.70 ... ... 1 200 1 219 11.13 331.54

48 48.000 0.469 238.30 ... ... 1 200 1 219 11.91 354.54

48 48.000 0.500 253.89 XS ... 1 200 1 219 12.70 377.81
48 48.000 0.562 285.00 ... ... 1 200 1 219 14.27 423.97
48 48.000 0.625 316.52 ... ... 1 200 1 219 15.88 471.17
48 48.000 0.688 347.97 ... ... 1 200 1 219 17.48 517.95
48 48.000 0.750 378.83 ... ... 1 200 1 219 19.05 563.74
48 48.000 0.812 409.61 ... ... 1 200 1 219 20.62 609.40
48 48.000 0.875 440.80 ... ... 1 200 1 219 22.23 656.10
48 48.000 0.938 471.90 ... ... 1 200 1 219 23.83 702.38

48 48.000 1.000 502.43 ... ... 1 200 1 219 25.40 747.67

48 48.000 1.062 532.88 ... ... 1 200 1 219 26.97 792.84
48 48.000 1.125 563.73 ... ... 1 200 1 219 28.58 839.04
48 48.000 1.188 594.50 ... ... 1 200 1 219 30.18 884.82
48 48.000 1.250 624.70 ... ... 1 200 1 219 31.75 929.62
52 52.000 0.375 206.95 ... ... 1 300 1 321 9.53 308.23
52 52.000 0.406 223.93 ... ... 1 300 1 321 10.31 333.26
52 52.000 0.438 241.42 ... ... 1 300 1 321 11.13 359.54
52 52.000 0.469 258.36 ... ... 1 300 1 321 11.91 384.50
52 52.000 0.500 275.27 ... ... 1 300 1 321 12.70 409.76
52 52.000 0.562 309.03 ... ... 1 300 1 321 14.27 459.86
52 52.000 0.625 343.25 ... ... 1 300 1 321 15.88 511.12
52 52.000 0.688 377.39 ... ... 1 300 1 321 17.48 561.93

52 52.000 0.750 410.90 ... ... 1 300 1 321 19.05 611.66

52 52.000 0.812 444.33 ... ... 1 300 1 321 20.62 661.27
52 52.000 0.875 478.21 ... ... 1 300 1 321 22.23 712.02
52 52.000 0.938 512.01 ... ... 1 300 1 321 23.83 762.33

52 52.000 1.000 545.19 ... ... 1 300 1 321 25.40 811.57

52 52.000 1.062 578.29 ... ... 1 300 1 321 26.97 860.69
52 52.000 1.125 611.84 ... ... 1 300 1 321 28.58 910.93
52 52.000 1.188 645.30 ... ... 1 300 1 321 30.18 960.74
52 52.000 1.250 678.15 ... ... 1 300 1 321 31.75 1 009.49

56 56.000 0.375 222.99 ... ... 1 400 1 422 9.53 331.96

56 56.000 0.406 241.29 ... ... 1 400 1 422 10.31 358.94
56 56.000 0.438 260.15 ... ... 1 400 1 422 11.13 387.26
56 56.000 0.469 278.41 ... ... 1 400 1 422 11.91 414.17
56 56.000 0.500 296.65 ... ... 1 400 1 422 12.70 441.39
56 56.000 0.562 333.06 ... ... 1 400 1 422 14.27 495.41
56 56.000 0.625 369.97 ... ... 1 400 1 422 15.88 550.67
56 56.000 0.688 406.80 ... ... 1 400 1 422 17.48 605.46

56 56.000 0.750 442.97 ... ... 1 400 1 422 19.05 659.11

56 56.000 0.812 479.05 ... ... 1 400 1 422 20.62 712.63
56 56.000 0.875 515.63 ... ... 1 400 1 422 22.23 767.39
56 56.000 0.938 552.12 ... ... 1 400 1 422 23.83 821.68

16
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

56 56.000 1.000 587.95 ... ... 1 400 1 422 25.40 874.83

56 56.000 1.062 623.70 ... ... 1 400 1 422 26.97 927.86
56 56.000 1.125 659.94 ... ... 1 400 1 422 28.58 982.12
56 56.000 1.188 696.10 ... ... 1 400 1 422 30.18 1 035.91
56 56.000 1.250 731.60 ... ... 1 400 1 422 31.75 1 088.57
60 60.000 0.375 239.02 ... ... 1 500 1 524 9.53 355.94
60 60.000 0.406 258.65 ... ... 1 500 1 524 10.31 384.87
60 60.000 0.438 278.88 ... ... 1 500 1 524 11.13 415.26
60 60.000 0.469 298.47 ... ... 1 500 1 524 11.91 444.13

60 60.000 0.500 318.03 ... ... 1 500 1 524 12.70 473.34

60 60.000 0.562 357.09 ... ... 1 500 1 524 14.27 531.30
60 60.000 0.625 396.70 ... ... 1 500 1 524 15.88 590.62
60 60.000 0.688 436.22 ... ... 1 500 1 524 17.48 649.44

60 60.000 0.750 475.04 ... ... 1 500 1 524 19.05 707.03

60 60.000 0.812 513.77 ... ... 1 500 1 524 20.62 764.50
60 60.000 0.875 553.04 ... ... 1 500 1 524 22.23 823.31
60 60.000 0.938 592.23 ... ... 1 500 1 524 23.83 881.63

60 60.000 1.000 630.71 ... ... 1 500 1 524 25.40 938.73

60 60.000 1.062 669.11 ... ... 1 500 1 524 26.97 995.71
60 60.000 1.125 708.05 ... ... 1 500 1 524 28.58 1 054.01
60 60.000 1.188 746.90 ... ... 1 500 1 524 30.18 1 111.83
60 60.000 1.250 785.05 ... ... 1 500 1 524 31.75 1 168.44
64 64.000 0.375 255.06 ... ... 1 600 1 626 9.53 379.91
64 64.000 0.406 276.01 ... ... 1 600 1 626 10.31 410.81
64 64.000 0.438 297.61 ... ... 1 600 1 626 11.13 443.25
64 64.000 0.469 318.52 ... ... 1 600 1 626 11.91 474.09

64 64.000 0.500 339.41 ... ... 1 600 1 626 12.70 505.29

64 64.000 0.562 381.12 ... ... 1 600 1 626 14.27 567.20
64 64.000 0.625 423.42 ... ... 1 600 1 626 15.88 630.56
64 64.000 0.688 465.64 ... ... 1 600 1 626 17.48 693.41

64 64.000 0.750 507.11 ... ... 1 600 1 626 19.05 754.95

64 64.000 0.812 548.49 ... ... 1 600 1 626 20.62 816.37
64 64.000 0.875 590.46 ... ... 1 600 1 626 22.23 879.23
64 64.000 0.938 632.34 ... ... 1 600 1 626 23.83 941.57

64 64.000 1.000 673.47 ... ... 1 600 1 626 25.40 1 002.62

64 64.000 1.062 714.52 ... ... 1 600 1 626 26.97 1 063.55
64 64.000 1.125 756.15 ... ... 1 600 1 626 28.58 1 125.90
64 64.000 1.188 797.69 ... ... 1 600 1 626 30.18 1 187.74
64 64.000 1.250 838.50 ... ... 1 600 1 626 31.75 1 248.30
68 68.000 0.469 338.57 ... ... 1 700 1 727 11.91 503.75
68 68.000 0.500 360.79 ... ... 1 700 1 727 12.70 536.92
68 68.000 0.562 405.15 ... ... 1 700 1 727 14.27 602.74
68 68.000 0.625 450.15 ... ... 1 700 1 727 15.88 670.12

68 68.000 0.688 495.06 ... ... 1 700 1 727 17.48 736.95

68 68.000 0.750 539.18 ... ... 1 700 1 727 19.05 802.40
68 68.000 0.812 583.21 ... ... 1 700 1 727 20.62 867.73
68 68.000 0.875 627.87 ... ... 1 700 1 727 22.23 934.60
68 68.000 0.938 672.45 ... ... 1 700 1 727 23.83 1 000.92

17
 ASME B36.10M-2015

Table 1 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Cont’d)
Identification
Customary Units [Standard (STD), SI Units
Outside Wall Plain End Extra-Strong (XS), Outside Wall Plain End
NPS Diameter, Thickness, Weight, or Double Extra Schedule DN Diameter, Thickness, Mass,
[Note (1)] in. in. lb/ft Strong (XXS)] No. [Note (2)] mm mm kg/m

68 68.000 1.000 716.23 ... ... 1 700 1 727 25.40 1 065.89

68 68.000 1.062 759.93 ... ... 1 700 1 727 26.97 1 130.73
68 68.000 1.125 804.26 ... ... 1 700 1 727 28.58 1 197.09
68 68.000 1.188 848.49 ... ... 1 700 1 727 30.18 1 262.92
68 68.000 1.250 891.95 ... ... 1 700 1 727 31.75 1 327.39
72 72.000 0.500 382.17 ... ... 1 800 1 829 12.70 568.87
72 72.000 0.562 429.18 ... ... 1 800 1 829 14.27 638.64
72 72.000 0.625 476.87 ... ... 1 800 1 829 15.88 710.06
72 72.000 0.688 524.48 ... ... 1 800 1 829 17.48 780.92

72 72.000 0.750 571.25 ... ... 1 800 1 829 19.05 850.32

72 72.000 0.812 617.93 ... ... 1 800 1 829 20.62 919.60
72 72.000 0.875 665.29 ... ... 1 800 1 829 22.23 990.52
72 72.000 0.938 712.55 ... ... 1 800 1 829 23.83 1 060.87

72 72.000 1.000 758.99 ... ... 1 800 1 829 25.40 1 129.78

72 72.000 1.062 805.34 ... ... 1 800 1 829 26.97 1 198.57
72 72.000 1.125 852.36 ... ... 1 800 1 829 28.58 1 268.98
72 72.000 1.188 899.29 ... ... 1 800 1 829 30.18 1 338.83
72 72.000 1.250 945.40 ... ... 1 800 1 829 31.75 1 407.25
76 76.000 0.500 403.55 ... ... 1 900 1 930 12.70 600.50
76 76.000 0.562 453.21 ... ... 1 900 1 930 14.27 674.18
76 76.000 0.625 503.60 ... ... 1 900 1 930 15.88 749.62
76 76.000 0.688 553.90 ... ... 1 900 1 930 17.48 824.45
76 76.000 0.750 603.32 ... ... 1 900 1 930 19.05 897.77
76 76.000 0.812 652.65 ... ... 1 900 1 930 20.62 970.96
76 76.000 0.875 702.70 ... ... 1 900 1 930 22.23 1 045.89
76 76.000 0.938 752.66 ... ... 1 900 1 930 23.83 1 120.22

76 76.000 1.000 801.75 ... ... 1 900 1 930 25.40 1 193.05

76 76.000 1.062 850.75 ... ... 1 900 1 930 26.97 1 265.74
76 76.000 1.125 900.47 ... ... 1 900 1 930 28.58 1 340.17
76 76.000 1.188 950.09 ... ... 1 900 1 930 30.18 1 414.01
76 76.000 1.250 998.85 ... ... 1 900 1 930 31.75 1 486.33
80 80.000 0.562 477.25 ... ... 2 000 2 032 14.27 710.08
80 80.000 0.625 530.32 ... ... 2 000 2 032 15.88 789.56
80 80.000 0.688 583.32 ... ... 2 000 2 032 17.48 868.43
80 80.000 0.750 635.39 ... ... 2 000 2 032 19.05 945.69

80 80.000 0.812 687.37 ... ... 2 000 2 032 20.62 1 022.83

80 80.000 0.875 740.12 ... ... 2 000 2 032 22.23 1 101.81
80 80.000 0.938 792.77 ... ... 2 000 2 032 23.83 1 180.17
80 80.000 1.000 844.51 ... ... 2 000 2 032 25.40 1 256.94
80 80.000 1.062 896.17 ... ... 2 000 2 032 26.97 1 333.59
80 80.000 1.125 948.57 ... ... 2 000 2 032 28.58 1 412.06
80 80.000 1.188 1,000.89 ... ... 2 000 2 032 30.18 1 489.92
80 80.000 1.250 1,052.30 ... ... 2 000 2 032 31.75 1 566.20

NOTES:
(1) NPS (Nominal Pipe Size) is a dimensionless designator that has been substituted in the customary units section for the previous term
Inch Nominal Size.
(2) DN (Nominal Diameter) is a dimensionless designator used in the SI (metric) system to describe pipe size.

18
 B32 AMERICAN NATIONAL STANDARDS FOR PRODUCT SIZES

Preferred Metric Sizes for Flat, Round, Square, Rectangular, and Hexagonal Metal Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B32.100-2005
Welded and Seamless Wrought Steel Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B36.10M-2015
Stainless Steel Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B36.19M-2004 (R2015)

The ASME Publications Catalog shows a complete list of all the Standards published by the Society. For a complimentary catalog, or the latest
information about our publications, call 1-800-THE-ASME (1-800-843-2763).
INTENTIONALLY LEFT BLANK
ASME B36.10M-2015

M03115