Venza HV

Doc. 22.61.00 Rev.
A 07/06/2023
Southeast Toyota Distributors, LLC

Accessory Installation Instructions
2023 Venza HV
SmartLED Ambient Lighting
Recommended Tools
Year & Model: 2023 Venza HV Safety Items
Part Number: 00016-00K02 Safety Glasses Safety Gloves
Accessory Code: LS1000 Special Tools
PIO / DIO: PIO & DIO N/A
Business Partner: J85
Installation Tools
Conflicts Philips Screwdriver #1 & #2 Plastic Pry Tool
None Torque Wrench 8mm Drill Bit
Protective Tape Moulding Remover
General Applicability 8, 10 mm Socket
Fits Models:
1. 2023 Venza HV
2.
3.
Special Chemicals
Additional Items Required For N/A
Installation
Item# Description: Legend
N/A
Sequence of Application
Item# Accessory:
1. N/A
SPECIAL NOTE: Installation Sequences
After TMS & Safety mandated preparatory steps have
been taken, the installation sequence is the suggested
method for completing the accessory installation. In
some instances the suggested sequence is written for one
associate to install & in others the sequence is given as
part of a team accessory installation. Unless otherwise
stated in the document, the associates may perform the
installation steps in any order to make the installation
as efficient as possible while maintaining consistent
quality.
Southeast Toyota Distributors, LLC Page 1 of 58

TOYOTA VENZA HV SmartLED Ambient Lighting
Document History Revisions

Version Date Description of Changes Made
Rev. A 07/06/2023 Originally Published

Table of Contents
Kit/Hardware Bag Contents ................................................................................................. 4

Parts for Installation ................................................................................................ .............5
Service & Warranty Information ............................................................................ ..............6
Installation Preparation:
Secure Vehicle ...................................................................................................................7

Battery Preparation .............................................................................................. ..........8-9
Disassembly Process..................................................................................................10-19
Assembly Process.......................................................................................................20-43
Reconnect Battery..........................................................................................................44
Checklist.............................................................................................................. .............45
Diagnostics ...................................................................................................................46-48
Block Diagram & Terminal of ECU.................................................................................49
Troubleshooting .................................................................................................................50
Disassembling the Output Side ....................................................................................51-53

Template............................................................................................................... ........54-55
BlankPage...........................................................................................................................56
Limited Warranty .........................................................................................................57-58

Kit/Hardware Bag Contents:
Item # Description
1 ECU Module
2 Power Harness
3 39" Fiber Optics Cable
4 Bezel
5 Output Lens
6 6" Zip Tie
7 14" Zip Tie
8 Customer Card

Parts for Installation:

Care must be taken when installing this accessory to ensure damage does not occur to the
vehicle. The installation of this accessory should follow approved guidelines to ensure a quality
installation. These guidelines can be found in the “Accessory Installation Practices” document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, re-checking torque procedure, etc.).
• Vehicle Disassembly/ Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector
removal, etc.).
Item # Quantity Description

1. 1 ECU Module
2. 1 Power Harness
3. 5 39" Fiber Optic Cables
4. 5 Bezels
5. 5 Output Lens
6. 10 6" Zip Tie
7. 3 14" Zip Tie
8. 1 Customer Card
4
1
2
6

Service & Warranty Information
Parts Information Warranty Information

Image
Key Part Number Description Warranty Labor Op. Code
Time
A 00016-00K02 Smart LED Ambient Lighting Kit 1.0 hr. AMB011
B 00016-ECU01 ECU Module 1.0 hr. AMB021
1 pc 39" Fiber, 1pc 24" Fiber 1.0 hr. AMB031

C 00016-FBRKT-01 3 Lenses, 3 Bezels
Labor times include consideration for diagnosis and Administration time.
If you are a dealer located outside of the Southeast Region, please contact the SET Accessory
Warranty Department at (888) 851-2722 or email Accessory.Warranty@SEToyota.com for
claim payment instructions.
Parts:
B– Smart LED, & Ambient Lighting Module C- 1 pc 39" Fiber, 1pc 24" Fiber3 Lenses, 3 Bezels

1. SECURE VEHICLE:
a. Fully apply the parking brake then turn the

vehicle off as shown in figure 1a.
If the vehicle is not secured and the shift lever is

moved, the vehicle may suddenly move, possibly
resulting in an accident or serious injury.
Figure 1a.
b. Pry the cover up using a screwdriver. To prevent

damage to the cover, cover the tip of the
screwdriver with tape or a rag as shown in figure
1b.
Figure 1b.
c. Press and hold the shift lock override button and

then push the button on the shift knob and move
the shifter knob to "N" as shown in figure 1c.
CAUTION:
Make sure to apply the parking brake before
performing this procedure.
Figure 1c.

Battery Preparation
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting
time may be required before disconnecting the
cable from the negative (-) auxiliary battery
terminal.
2a. REMOVE REAR NO. 2 FLOOR

BOARD
Figure 2a (a) Turn back the deck board assembly, as
shown in Figure 2a.
(b) Disengage the 3 clips to remove the rear
No. 2 floor board, as shown in Figure
2b.
Figure 2b

2b. REMOVE BATTERY HOLE COVER

(a) Disengage the 8 claws to remove the
battery hole cover, as shown in Figure
2c.
Figure 2c
2c. DISCONNECT CABLE FROM

NEGATIVE AUXILIARY BATTERY
TERMINAL
10mm Socket and Drive
(a) Loosen the nut, and disconnect the cable

from the negative (-) auxiliary battery
terminal, as shown in Figure 2d.
Figure 2d

3. REMOVE NO. 2 INSTRUMENT

CLUSTER FINISH PANEL GARNISH
(a) Disengage the 10 clips to remove the

No. 2 instrument cluster finish panel
garnish, as shown in Figure 3.
Figure 3
Remove in this Direction
4. REMOVE UPPER NO. 2 CONSOLE

PANEL GARNISH
(a) Apply protective tape to the area, as

shown in Figure 4.
(b) Disengage the 8 clips to remove the upper
No. 2 console panel garnish, as shown in
Figure 4.
Figure 4
Protective Tape

5. REMOVE UPPER CONSOLE COVER
(a) Apply protective tape to the area, as

shown in Figure 5.
(b) Disengage the 7 clips to remove the upper
console cover, as shown in Figure 5.
Figure 5
Protective Tape

6. REMOVE CONSOLE BOX

ORNAMENT (w/ Seat Heater System)
Moulding Remover
(a) Using a moulding remover, disengage

the 2 claws and 6 clips, as shown in
Figure 6.
(b) Disconnect the connector to remove the
console box ornament, as shown in
Figure 6 Figure 7.
Remove in this direction
Figure 7
7. REMOVE CONSOLE BOX

ORNAMENT (W/O SEAT HEATER
SYSTEM)
Moulding Remover

the 2 claws and 6 clips to remove the
console box ornament, as shown in
Figure 8.
Figure 8

8. REMOVE SHIFT LEVER KNOB SUB-

ASSEMBLY
Screwdriver
(a) Disengage the 2 claws to disconnect the

shifting hole cover sub-assembly as
shown in the illustration, as shown in
Figure 9.
(b) Using a screwdriver with its tip wrapped
Figure 9 with protective tape, expand the left side
of the clip and remove the shift lever
sub-assembly from the transmission
floor shift assembly, as shown in
Figure 10.
NOTICE:
• Be careful not to damage the shift
lever knob sub-assembly.
• The clip is difficult to remove. Check
that the clip is installed to the shift
Figure 10 lever knob sub-assembly after
removing the shift lever knob sub-
*a Clip assembly.
*b Protective Tape • If the installation procedures
described in the repair manual are not
performed correctly, the shift lever
knob sub-assembly may fall off.

9. REMOVE UPPER CONSOLE PANEL

SUB-ASSEMBLY
(a) Move the shift lever to N.

(b) Disengage the 4 clips, 6 claws, and 3
guides as shown in the illustration, as
shown in Figure 11.
(c) Disconnect the 3 connectors and
disengage the 2 clamps to remove the
upper console panel sub-assembly, as
Figure 11 shown in Figure 12.
Figure 12

10. REMOVE CONSOLE CUP HOLDER

BOX SUB-ASSEMBLY
(a) Remove the bolt shown in Figure 11.

(b) Disengage the 14 clips as shown in
Figure 13.
(c) Pull in the direction indicated by the
arrow (2) shown in Figure 13 to detach
the guide and remove the upper console
box.
Figure 13 (d) Disconnect the connector to remove the
console cup holder box sub-assembly, as
Remove in this direction shown in Figure 14.
Figure 14

11. REMOVE FRONT DOOR SCUFF

PLATE LH
(a) Place your hand at the position shown in

Figure 15 and pull in the removal
direction to disengage the 2 claws and
guide.
Figure 15
Place Hand Here

(b.) Place both hands at the position shown in

Figure 16 and lift in the direction indicated
by the arrow to detach the 6 claws and guide,
and remove the front door scuff plate.
Figure 16
Place Hand Here
12. REMOVE COWL SIDE TRIM

BOARD LH
(a) Remove the clip, as shown in Figure 17.
(b) Disengage the clip to remove the cowl

side trim board LH, as shown in Figure
17.
Figure 17


PANEL UNDER COVER SUB-
ASSEMBLY
Screwdriver
(a) Pull the No. 1 instrument panel under

cover sub-assembly in the direction
indicated by the arrow (1) shown in
Figure 18 to disengage the 3 claws .
Figure 18 (b) Pull the No. 1 instrument panel under

indicated by the arrow (2) shown in
Remove in this Direction (1) Figure 18 to disengage the guide.
(c) Disengage the 2 claws (*a) to disconnect
Remove in this Direction (2) the DLC3, as shown in Figure 18.
(d) Disconnect the connector and disengage
the clamp to remove the No. 1
instrument panel under cover sub-
assembly, as shown in Figure 19 (w/o
illumination), or Figure 20
(w/illumination).
Figure 19
Figure 20

14. REMOVE FRONT NO. 2 CONSOLE

BOX INSERT
(a) Pull the front No. 2 console box insert in
the direction indicated by the arrow (1)
shown in Figure 21 to disengage the 3
clips.
(b) Pull the front No. 2 console box insert in

shown in Figure 21 to disengage the
guide and remove it.
Figure 21
Remove in this direction (1)
15. REMOVE FRONT NO. 1 CONSOLE

BOX INSERT
(a) Pull the front No. 1 console box insert in

to disengage the 3 clips, as shown in
Figure 22.
(b) Pull the front No. 1 console box insert in
to disengage the guide and remove it, as
shown in Figure 22.
Figure 22


ASSEMBLY
(a) Pull the No. 2 instrument panel under

indicated by the arrow (1) to disengage
the 4 claws, as shown in Figure 23.
(b) Pull the No. 2 instrument panel under
indicated by the arrow (2) to disengage
Figure 23 the 2 guides and remove it, as shown in
Figure 23.
Remove in this direction (1) (c) Disconnect the connector and disengage
the clamp to remove the No. 2
Remove in this direction (2) instrument panel under cover sub-
assembly, as shown in Figure 24 (w/o
illumination), or Figure 25
(w/illumination).
Figure 24
Figure 25

17. REMOVE CONSOLE REAR END

PANEL SUB-ASSEMBLY
Moulding Remover

the 2 claws and 6 clips, as shown in
Figure 26.
(b) Disconnect the connector to remove the
console rear end panel sub-assembly, as
Figure 26 shown in Figure 27.
Figure 27

18. HOLE DRILLING INSTRUCTIONS
8mm drill bit
Drill 8mm holes with 8mm drill bit, as

shown in Figure 28.
Be sure to drill at a 90-degree angle to

produce an even round hole, as shown
in Figure 28.
NOTICE:
Disassembly instructions are provided at the
end of this manual.
Figure 28
19. DRIVER SIDE PANEL HOLE

DRILLING
8mm drill bit
(a) Drill a hole on the panel marking shown

in Figures 29 & 30.
Figure 29
NOTICE:
DIO use the template at the end of this
manual.
Figure 30

20. PASSENGER SIDE PANEL HOLE

DRILLING
8mm drill bit
(a) Drill a hole using the template at the end

of this manual, as shown in Figures 31 &
32.
NOTICE:
Figure 31
DIO use the template at the end of this
manual.
Figure 32

21. CENTER CONSOLE HOLE

DRILLING
8mm drill bit
(a) Drill a hole using the template at the end

of this manual, as shown in Figures 33 &
34.
Figure 33
Figure 34

22. REAR END PANEL SUB-ASSEMBLY

HOLE DRILLING
8mm drill bit
(a) Drill two holes on the panel marking

shown in Figures 35 & 36.
Figure 35
Figure 36

23. INSTALL THE ECU MODULE AND

ROUTE THE FIBER OPTIC CABLES
Do not bend the fiber optic cables

closer than 4 inches from the ECU, as
shown in Figure 37.
Do gently bend the fiber optic cables,

as shown in Figure 38.
Do not over bend the fiber optic cables,

and do not over tighten cables with a
zip tie, as shown in Figure 39.
(a) Install the ECU Module, orienting the
Figure 37 ECU module so that the side with three
fiber optic cables is facing the rear of the
vehicle, and the side with two cables is
facing the front.
(b) Route the fiber optic cables, as shown in
Figure 40.
(c) Leave enough slack to insert the fiber
optics into the removed panels, and
secure the remainder of the fiber optic
cables using supplied zip ties.
NOTICE:
Do not over tighten the fiber optic cables
with the zip ties.
Figure 38
Figure 39

Figure 40
24. MAKE THE HARNESS

CONNECTION
(a) Make the harness connection to the shift

knob connector, as shown in Figure 41,
and secure to the harness with a zip tie.
Figure 41 NOTICE:
Do not mix the connection up with another
10-pin connector that is present on the upper
panel sub-assembly for off road controls.

25. SECURE THE ECU MODULE
(a) Secure the ECU Module, as shown in

Figures 42 & 43.
(b) Use 14” zip ties and mounting tabs.
Make sure to mount the ECU Module

flat, with plastic cover facing up, and
facing toward the driver’s seat, as
shown in Figure 43.
Figure 42
Figure 43

26. ROUTE THE FIBER OPTIC CABLES
(a) Route one fiber optic cable to the front

driver side footwell, as shown in Figure
44.
(b) Route one fiber optic cable to the front
passenger side footwell, as shown in
Figure 44.
Figure 44

(c) Route three fiber optic cables to the rear end

panel sub-assembly, as shown in Figure 45,
coming out at the rear console end panel sub
assembly.
Figure 45

27. ROUTE A FIBER OPTIC CABLE TO

DRIVER FOOTWELL
(a) Route the fiber optic cable in the driver’s

footwell and secure it with a zip tie, as
shown in Figures 46 & 47.
NOTICE:
Figure 46 Leave enough slack to be able to plug the fiber
optics cable into the panel and safely remove
the panel for serviceability.
Figure 47

28. ROUTE A FIBER OPTIC CABLE TO

PASSENGER FOOTWELL
(a) Route the fiber optic cable in the

passenger’s footwell, as shown in
Figure 48.
NOTICE:
Leave enough slack to be able to plug the
Figure 48 fiber optics cable into the panel and safely
remove the panel for serviceability.
29. ROUTE THREE FIBER OPTIC

CABLES TO REAR OF THE CENTER
CONSOLE
(a) Route three fiber optic cables to the rear

of the console and secure with a wire tie,
NOTICE:
Leave enough slack to be able to plug the
fiber optics cable into the panel and safely
remove the panel for serviceability.
Figure 49

30. VERIFY FIBER OPTIC CABLES
1. Verify all 5 fiber optic cables are

installed and routed as shown in Figures
50, 51, 52, & 53.
2. Verify all fiber optic cables are secured.
3. Verify fiber optic cables are not over
bent.
4. Verify that enough slack is left for
panels to be safely removed for
serviceability.
If all the above items are verified you are
now ready to install the bezels and lenses.
Figure 50
Figure 51
Figure 52

Figure 53
31. INSTALL BEZELS AND LENSES
(a) Install a provided bezel into the hole that

was drilled, as shown in Figure 54.
(b) Route the fiber optic through the bezel,
(c) Install a provided lens on the end of the
fiber optic cable, as shown in Figure 56.
(d) Push the fiber optic cable with the lens
into the bezel, pushing in until it clicks
into the bezel, as shown in Figure 57.
See next page for figures.
Figure 54
Do not damage the lens. Guide it

directly into the bezel and do not bend
the ends of the lens.

(e) Repeat these steps for each fiber optic

cable.
Figure 55
Figure 56
Figure 57

32. REINSTALL CONSOLE REAR END

PANEL SUB-ASSEMBLY
(a) Connect the connector.

(b) Engage the 6 clips and 2 claws as shown
in the illustration to install the console
rear end panel sub-assembly, as shown
in Figure 58.
Figure 58
Install in this direction
33. REINSTALL NO. 2 INSTRUMENT

ASSEMBLY
(a) Engage the clamp and connect the

connector.
(b) Engage the 2 guides and 4 claws to
install the No. 2 instrument panel under
cover sub-assembly, as shown in
Figure 59.
Figure 59
Install in this direction (1)

34. REINSTALL FRONT NO. 1

CONSOLE BOX INSERT
(a) Engage the guide and 3 clips to install

the front No. 1 console box insert, as
shown in Figure 60.
Figure 60
35. REINSTALL FRONT NO. 2

CONSOLE BOX INSERT
(a) Engage the guide and 3 clips to install

the front No. 2 console box insert, as
shown in Figure 61.
Figure 61


ASSEMBLY
Screwdriver
(a) Engage the clamp and connect the

connector.
(b) Engage the 2 claws to connect the
DLC3.
Figure 62
(c) Engage the guide and 3 claws, as shown
in Figure 62.
(d) Install the No. 1 instrument panel under
cover sub-assembly with the 3 screws, as
Install in this direction (2) shown in Figure 62.
37. REINSTALL COWL SIDE TRIM

BOARD LH
(a) Engage the clip, as shown in Figure 63.

(b) Install the cowl side trim board LH
with the clip, as shown in Figure 63.
Figure 63

38. REINSTALL FRONT DOOR SCUFF

PLATE LH
(a) w/ Illumination:
(1) Connect the connector.
(b) Engage the 2 guides and 8 claws to
install the front door scuff plate LH, as
shown in Figure 64.
Figure 64
39. INSTALL CONSOLE CUP HOLDER

BOX SUB-ASSEMBLY

(b) Engage the 14 clips, as shown in
Figure 65.
(c) Install the console cup holder box sub-
assembly with the bolt, as shown in
Figure 65.
Figure 65
40. REINSTALL UPPER CONSOLE

PANEL SUB-ASSEMBLY
(a) Connect the 3 connectors and engage the

2 clamps, as shown in Figure 66.
(b) Engage the 3 guides, 6 claws and 4 clips
to install the upper console panel sub-
assembly, as shown in Figure 66.
(c) Move the shift lever to P.
Figure 66

41. REINSTALL SHIFT LEVER KNOB

SUB-ASSEMBLY
(a) Install the shift lever knob sub-assembly

to the transmission floor shift assembly,
(b) Engage the 2 claws to connect the

shifting hole cover sub-assembly as
shown in the illustration, as shown in
Figure 68.
Figure 67
NOTICE:
Make sure that the shifting hole cover sub-
assembly does not twist after installing the
shift lever knob sub-assembly.
Figure 68
42. REINSTALL CONSOLE BOX

ORNAMENT (W/O SEAT HEATER
SYSTEM)
(a) Engage the 6 clips and 2 claws to

install the console box ornament, as
shown in the Figure 69.
Figure 69
Install in this Direction

43. REINSTALL CONSOLE BOX

ORNAMENT (W/ SEAT HEATER
SYSTEM)

(b) Engage the 6 clips and 2 claws to
install the console box ornament, as
shown in the Figure 70.
Figure 70
44. REINSTALL UPPER CONSOLE

COVER
(a) Engage the 7 clips to install the upper

console cover, as shown in the Figure 71.
Figure 71
45. REINSTALL UPPER NO. 2

CONSOLE PANEL GARNISH
(a) Engage the 8 clips to install the upper

No. 2 console panel garnish, as shown
in the Figure 72.
Figure 72


CLUSTER FINISH PANEL GARNISH
(a) Engage the 10 clips to install the No. 2

instrument cluster finish panel
garnish, as shown in the Figure 73.
Figure 73
47. TESTING AND REASSEMBLY
Take special care to make sure all

harnesses and wiring are properly
secured.
Make sure harnesses are not pinched or

bound by trim pieces.
Make sure fiber optic cables are not

pinched or bent more than a 30 mm
radius.

48a. RECONNECT THE BATTERY
10mm Socket and Torque Wrench
(a) Reconnect the battery. Connect the cable to

the negative (-) battery terminal and tighten
the nut to the specified torque, as shown in
Figure 74a.
Figure 74a Torque: 5.4 N·m {55 kgf·cm, 48 in·lbf}
CAUTION: Do not touch the positive

terminal.
NOTICE: When disconnecting the

cable, some systems need to be initialized after
the cable is reconnected.

48b. REINSTALL BATTERY HOLE

COVER
(a) Engage the 8 claws and install the
battery hole cover, as shown in Figure
74b.
Figure 74b
48c. REINSTALL REAR NO. 2 FLOOR

BOARD
(a) Engage the 3 clips to install the rear No.
2 floor board, as shown in Figure 74c.
(b) Turn down the deck board assembly as
shown in Figure 74d.
Figure 74c
Figure 74d

CHECKLIST – These Points Must Be Checked To Ensure A Quality Installation
Check: Look for:
Ignition Verify vehicle will crank
SRS Warning Light Confirm SRS warning light illuminates for

approximately 6 seconds with the ignition on and then
goes out
Turn Headlight on a) Verify interior illumination around shifter is

working
b) Verify ambient light is working from all sources
Start SmartLED app Run Diagnostics mode (next page) and verify
accessory changes colors and brightness
Warranty Statement Place in glove box (DIO only)
Customer Card Place in glove box

DIAGNOSTICS
1. INSTALL AND OPEN THE SmartLED

APP
a. Install and then open the SmartLED

app, as shown in Figure 1.
Figure 1
2. SELECT THE BLUETOOTH DEVICE
a. Select the SmartLED Bluetooth device,

Figure 2

3. MAKE SURE VEHICLE’S

ILLUMINATION IS ON
a. Be sure the vehicle illumination is on, as

shown in Figure 3.
Figure 3
4. GO TO SETTINGS AND SELECT TO

RUN DIAGNOSTIC MODE
a. Verify the proper operation of each zone

and channel as the app goes through the
diagnostic mode, as shown in Figure 4.
Figure 4
5. VERIFY LIGHT COLORS IN THE

FRONT OF THE VEHICLE
(A) Verify the colors are shown in the app

correspond to the actual colors in the
front of the vehicle, as shown in Figure
5.
- Red
- Green
- Blue
- Yellow
- Purple
- Cyan
- White
- Black (Off)
Figure 5
6. VERIFY LIGHT COLORS IN THE

REAR OF THE VEHICLE
(B) Verify the colors are shown in the app

correspond to the actual colors in the
REAR of the vehicle, as shown in
Figure 6.
- Red
- Green
- Blue
- Yellow
- Purple
- Cyan
- White
- Black (Off)
Figure 6

Block Diagram
Terminal of ECU

Troubleshooting Guide
Symptom Check
No illumination from 1. Turn headlights on.

interior light by the shifter 2. Check and verify harness connection.
SmartLED app doesn't 1. Reboot the phone.

connect to module 2. Turn the car off, wait 20 sec, turn the car on.
No illumination from 1. Turn headlight ON.

interior ambient light, all 2. Light is turned off in the app.
sources 3. ECU reached temp 55C (130F) and needs to cool down.
4. Check and verify harness connection
One or more (not all) light 1. Light is turned off in the app for one or more zones.
sources do not have the 2. Check and verify fiber optics cable connection at ECU and
light Bezel.
3. Make sure fiber optic cable isn't bent more than 30mm radius.

Disassembling the Output Side
1. DISASSEMBLING THE OUTPUT

SIDE
8mm Socket
8mm (a) Take an 8mm socket and wrap the end in

Socket protective tape, as shown in Figure 1.
NOTICE:
Protective tape is required protect the bezel
from getting scratched by the 8mm socket.
Figure 1 (b) Press 8mm socket firmly against the

bezel, as shown in Figure 2.
Figure 2

(c) Push the fiber optic cable in the direction

shown in Figure 3, until the lens comes
out as shown in step (d).
(d) Push the fiber optic cable in step (c) until

lens is pushed from inside the bezel, as
shown in Figure 4.
Figure 3
Figure 4

(e) Remove the lens from the fiber optic

cable, as shown in Figure 5.
(f) Pull the fiber optic cable out of the hole.
Figure 5

TEMPLATE
Print this page and cut out the dotted portion and use it as a template.
MY23 Venza SmartLED Ambient Lighting Passenger foot well
Dept. Technical reference Created by Approved by
New Products TBD Idoko Abuh 6/9/2023

Document type Document status
Template
Title DWG No.
MY23 Venza SmartLED 1

Ambient Lighting
Passenger foot well
Rev. Date of issue Sheet
1/1

TEMPLATE
Print this page and cut out the dotted portion and use it as a template.
MY23 Venza SmartLED Ambient Lighting

Center Console Template
Dept. Technical reference Created by Approved by
New Products TBD Idoko Abuh 6/9/2023

Document type Document status
Template
Title DWG No.
MY23 Venza SmartLED

Ambient Lighting Center
Console Template
Rev. Date of issue Sheet
1/1


SOUTHEAST TOYOTA DISTRIBUTORS, LLC (“we,” “our” and “us”) provides the following limited warranty on our accessories, excluding tires, (“Accessories” or
“Accessory”) installed on a Toyota. This limited warranty is not provided by and does not bind or provide benefit to the vehicle dealer, the manufacturer, or Toyota
Motor Sales, U.S.A., Inc. This limited warranty does not apply to tires; please consult the tire manufacturer and/or its materials accompanying the vehicle for any
warranty terms concerning tires. This limited warranty also does not apply to ToyoGuard Exterior Paint Sealant and ToyoGuard Interior Protector; please consult the
ToyoGuard Limited Warranty Certificate for the warranty terms concerning those products.
SCOPE OF LIMITED WARRANTY:

A. Protection:
i. Accessories Installed by Southeast Toyota Distributors, LLC on a new Toyota vehicle. We warrant that, for a period of 36 months or 36,000
miles, whichever occurs first, we will repair or replace (includes labor), free of charge, any defect in such an Accessory due to faulty material or
workmanship, or, at our option, provide a full refund of the purchase price of the Accessory. The warranty period begins on the vehicle’s In-Service
Date, which is the first date the new vehicle is either delivered to an ultimate purchaser, leased, or used as a company car or demonstrator. Accessories
installed by Southeast Toyota Distributors, LLC are identified on the vehicle’s window sticker (Monroney Label).
ii. Accessories Installed by a Toyota Dealer on a Toyota vehicle. We warrant that, for 12 months, regardless of mileage, from the date such an
Accessory was installed on the vehicle or the remainder of the Toyota new vehicle warranty, whichever is longer, we will repair or replace (includes
labor), free of charge, any defect in the Accessory due to faulty material or workmanship, or, at our option, provide a full refund of the purchase price of
the Accessory. For a new vehicle, the warranty period begins on the vehicle’s In-Service Date, which is the first date the new vehicle is either delivered
to an ultimate purchaser, leased, or used as a company car or demonstrator.
iii. Accessories purchased from a Toyota Dealer but not installed by the Toyota Dealer. We warrant that, for a period of 12 months, regardless of
mileage, from the date the accessory was purchased, we will repair or replace (does not include labor), free of charge, any defect in the Accessory due
to faulty material or workmanship, or, at our option, provide a full refund of the purchase price of the Accessory.
B. Limitation of Warranty. This limited warranty does not apply to, and we will not repair, replace, or reimburse you for: (1) wheel balancing and wheel
alignments, except for one wheel balancing or alignment during the first 12 months or 12,000 miles, whichever occurs first, from the vehicle’s In-Service Date,
as defined above, (2) abrasions or dents, whatever their cause, and any failure or damage resulting directly or indirectly from accidents, collisions, impacts from
foreign objects, fire, theft, larceny, explosion, malicious mischief, vandalism, civil commotion, riots, war, or any other similar causes, (3) any failure or damage
resulting directly or indirectly from lightning, windstorms, hail, water, floods, subfreezing temperatures, airborne chemicals, tree sap, dust, salt, and any other
environmental conditions or similar causes, (4) any failure or damage caused by: (a) a failure of any part, other than the Accessory, (b) any misuse, abuse,
improper towing, negligence or lack of maintenance of the vehicle or Accessory, (c) the alteration, modification or repair of the Accessory by anyone other than
persons expressly authorized by us to perform such alteration, modification or repair, or (d) the use of the vehicle for commercial purposes, competitive driving
or racing, (5) any failure or damage, if the Accessory has not been installed according to instructions, (6) any failure or damage occurring outside of Canada,
the United States of America, its territories or possessions, (7) except to the extent required by the state whose laws govern this limited warranty, any
consequential, secondary, or unreasonable costs that may be suffered as a result of the need to repair or replace the Accessory, including without limitation any
loss of use of the vehicle, road service, towing, storage charges, inconvenience, loss of wages and/or income, additional expense incurred, loss of transportation,
rental car expense, or any derivative damage to persons or things other than the Accessory, including other parts of the vehicle, or (8) liability for damage to
property or for injury to or death of any person, arising out of the operation, maintenance or use of your vehicle whether or not related to the covered Accessory.
C. Exclusive Remedy. If there is a valid claim under this limited warranty for a defect due to faulty material or workmanship in the Accessory, we will, at our
option, either: (i) repair, (ii) replace or (iii) provide a full refund of the purchase price of the Accessory. We have no other obligations under this limited warranty.
Refunds will be made to the vehicle owner. If the vehicle is leased, the refund will be made to the leasing company.
HOW TO MAKE A CLAIM: In the event of a warranty claim, please contact the nearest Toyota dealer to arrange for repairs. The dealership must receive
our prior authorization before making repairs covered by this limited warranty. The dealer will contact Southeast Toyota Distributors, LLC at 1-888-851-2722,
select option #5 (Warranty Department), then option #4 (Repairs), for instructions on processing a warranty claim, if they are not already familiar with the process. If
you have any questions or concerns regarding repairs covered by this limited warranty, please contact our Customer Assistance Hotline at 1-800-301-6859.
OUR DISPUTE RESOLUTION PROGRAM: Your satisfaction is our highest priority. In keeping with that focus, in the event that an issue arises related to
this Limited Warranty, we invite you to call our Customer Assistance Hotline at 1-800-301-6859 to discuss it. In most cases, we expect that a satisfactory
resolution of your issue can be reached through engagement with that Department. If our Customer Loyalty Department is unable to resolve your issue to your
satisfaction, we offer a dispute resolution program administered by the National Center for Dispute Settlement (NCDS) (“the Program”). The purpose of the Program
is to resolve disputes in an informal setting before an impartial arbitrator. The Program is free of charge to you (although you must bear the cost of any expert
witness or attorney you elect to employ). You are required to complete the Program before exercising rights or seeking remedies under the federal Magnuson-Moss
Warranty Act, 15 U.S.C. § 2301 et seq. (“the Act”). If you choose to seek remedies that are not created by the Act, you are not required to use the Program before
pursuing such remedies – although the Program is still available to you to resolve the dispute. When utilizing the Program, you will need to provide (a) the vehicle
identification number of your vehicle, (b) the identity of your selling and servicing dealerships, (c) the mileage on your vehicle at relevant times, (d) the date and
nature of any relevant repairs, (e) legible copies of repair orders and other relevant documents, (f) a summary of the unresolved issue and the requested action, and
(g) your contact information. In most cases, the dispute resolution process under the Program will be completed within forty (40) days of your submission of your
request and will consist of steps such as an initial eligibility determination, an opportunity for you and us to submit information in writing relating to your claim, an oral
hearing, and a decision from the arbitrator. A decision will be binding on you only if you choose to accept it. You may submit a request to NCDS by telephone at
their toll free number: (877)-276-8848 or in writing at P.O. Box 463196, Mt. Clemens, MI 48046. You may obtain additional information regarding the Program at
www.ncdsusa.org. In the event that the NCDS does not exist or no longer handles disputes for us at the time that you seek to submit a request, you may contact our
Customer Assistance Hotline at 1-800-301-6859 to obtain current information about our dispute resolution programs.

TOYOTA MODEL ACCESSORY
GENERAL LIMITATION OF WARRANTY: THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES OR
LIABILITIES. IN NO EVENT SHALL WE BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS
OR ANY OTHER WARRANTY. SOME STATES DO NOT ALLOW THE EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE INFORMATION OR EXCLUSION MAY NOT APPLY. NO EXPRESS WARRANTY OF
FITNESS OR MERCHANTABILITY IS GRANTED BY THIS LIMITED WARRANTY. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THOSE DESCRIBED IN THIS DOCUMENT. ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH MAY BE APPLICABLE BY OPERATION OF LAW SHALL
BE LIMITED TO THE PERIOD OF THIS WRITTEN LIMITED WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY. THIS LIMITED WARRANTY PROVIDES
SPECIFIC LEGAL RIGHTS, AND THERE MAY BE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. ANY ACTION FOR
BREACH OF ANY WARRANTY HEREUNDER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT
WITH IN A PERIOD NOT EXCEEDING 12 MONTHS AFTER EXPIRATION OF THIS LIMITED WARRANTY. THE REMEDIES SPECIFIED
HEREIN AND THOSE SPECIFIED BY APPLICABLE LAW ARE THE ONLY REMEDIES AVAILABLE. WE ASSUME NO OTHER
OBLIGATION OR RESPONSIBILITY WITH REGARD TO THE ACCESSORY. WE NEITHER ASSUME, NOR AUTHORIZE ANYONE TO
ASSUME FOR US, ANY ADDITIONAL LIABILITY IN CONNECTION HEREWITH.
GENERAL: This limited warranty describes the complete and exclusive rights that result from the purchase of Accessories. No oral representations or
statements may be relied upon. This limited warranty may not be amended or modified, and additional rights may not be granted, unless in a written
statement signed by one of our officers. This limited warranty shall be governed by the laws of the state where the vehicle is purchased, excluding laws
concerning conflicts of law. We may delegate the performance of our duties and obligations and assign our rights and benefits hereunder. For inquiries
regarding this limited warranty, we can be contacted directly at Customer Assistance Hotline at 1-800-301-6859, or by mail to:
Southeast Toyota Distributors, LLC, Attention: Customer Loyalty Department, 100 Jim Moran Boulevard, Deerfield Beach, Florida
33442.
Rev. 12/01/16

Venza HV

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Venza HV

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Venza HV

Uploaded by

Copyright:

Available Formats

Doc. 22.61.00 Rev.

Southeast Toyota Distributors, LLC

Southeast Toyota Distributors, LLC Page 1 of 58

Document History Revisions

Rev. A 07/06/2023 Originally Published

Southeast Toyota Distributors, LLC Page 2 of 58

Kit/Hardware Bag Contents ................................................................................................. 4

Secure Vehicle ...................................................................................................................7

Disassembling the Output Side ....................................................................................51-53

Southeast Toyota Distributors, LLC Page 3 of 58

Kit/Hardware Bag Contents:

Southeast Toyota Distributors, LLC Page 4 of 58

Parts for Installation:

Item # Quantity Description

Southeast Toyota Distributors, LLC Page 5 of 58

Service & Warranty Information

Parts Information Warranty Information

B 00016-ECU01 ECU Module 1.0 hr. AMB021

1 pc 39" Fiber, 1pc 24" Fiber 1.0 hr. AMB031

Labor times include consideration for diagnosis and Administration time.

Southeast Toyota Distributors, LLC Page 6 of 58

a. Fully apply the parking brake then turn the

If the vehicle is not secured and the shift lever is

b. Pry the cover up using a screwdriver. To prevent

c. Press and hold the shift lock override button and

Southeast Toyota Distributors, LLC Page 7 of 58

2a. REMOVE REAR NO. 2 FLOOR

Southeast Toyota Distributors, LLC Page 8 of 58

2b. REMOVE BATTERY HOLE COVER

2c. DISCONNECT CABLE FROM

10mm Socket and Drive

(a) Loosen the nut, and disconnect the cable

Southeast Toyota Distributors, LLC Page 9 of 58

3. REMOVE NO. 2 INSTRUMENT

(a) Disengage the 10 clips to remove the

Remove in this Direction

4. REMOVE UPPER NO. 2 CONSOLE

(a) Apply protective tape to the area, as

Remove in this Direction

Southeast Toyota Distributors, LLC Page 10 of 58

5. REMOVE UPPER CONSOLE COVER

(a) Apply protective tape to the area, as

Remove in this Direction

Southeast Toyota Distributors, LLC Page 11 of 58

6. REMOVE CONSOLE BOX

(a) Using a moulding remover, disengage

Remove in this direction

7. REMOVE CONSOLE BOX

(a) Using a moulding remover, disengage

Remove in this direction

Southeast Toyota Distributors, LLC Page 12 of 58

8. REMOVE SHIFT LEVER KNOB SUB-

(a) Disengage the 2 claws to disconnect the

Southeast Toyota Distributors, LLC Page 13 of 58

9. REMOVE UPPER CONSOLE PANEL

(a) Move the shift lever to N.

Remove in this direction