Product Support Document

Calibrate Baro Encoder

Prepared by: Vorasinh Keobouarabath

Approved by:
Date of issue:
 Revision History

First Issued
Version Description Author
(yyyy-mm-dd)
pre-
2018-01-26 Preliminary Draft VK
release
001 2018-01-29 First General Release VK

Product Support Document

Calibrate Baro Encoder
Page 2 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 2 of 10
 TABLE OF CONTENTS
Section/Title Page

1 Purpose and Scope .................................................................................................................. 4

2 Overview................................................................................................................................... 4
3 Tools and Software .................................................................................................................. 5
3.1 Tools Required .................................................................................................................. 5
3.2 Software Required ............................................................................................................ 5
4 How to finding CANBus address to Instrument panel .............................................................. 5
4.1 H:\usr\Ascent\common_data\hardware Exemple 0011268700001 Open IOdef file ......... 5
4.2 Open CANSniffer with Node 109 depend panel Can address .......................................... 5
5 Validate functionality ................................................................................................................ 8
5.1 Check encoder value ........................................................................................................ 8
6 Troubleshoot............................................................................................................................. 9
6.1 Upcoming Contents ......................................................................................................... 10

Product Support Document

Calibrate Baro Encoder
Page 3 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 3 of 10
1 Purpose and Scope
Purpose

The purpose of this document is to establish and define a clear setup, calibration guide
for ISIS and ISFD Encoder

Scope

This procedure applies to sims using:

• MA00075881-04-001 ISIS Instrument
• MA00075881-05-001 EISI Instrument
• MA00075881-06-001 ISFD Instrument
• 3020453 EISI Instrument ATR

This guide is to be used by TRU personnel during the HW integration only. It is not
intended for customer use; all on-site recalibration or debugging should be done by a
qualified TRU employee.

2 Overview

Product Support Document

Calibrate Baro Encoder
Page 4 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 4 of 10
3 Tools and Software

3.1 Tools Required

• Laptop or DEV Computer

3.2 Software Required

• CanSniffer

4 How to finding CANBus address to Instrument panel

4.1 H:\usr\Ascent\common_data\hardware Exemple 0011268700001

Open IOdef file
o Should find CANbus address in 0011268700001.dat or on panel label
EX: define ISIS @1.109
More detail sees to Maintenance Manual specify aircrate

4.2 Open CANSniffer with Node 109 depend panel Can address
Exemple

Product Support Document

Calibrate Baro Encoder
Page 5 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 5 of 10
 o Type VER 3 and Enter
o Turning knob to validate Digital Input (DI) make sure the value increments and
decrement correctly (No jumping). If you have problem value jumping that mean
need “to do Calibration Encoder”
o Type CAL and Enter
o Turn the knob Clock wise, follow message until you see message appear
Counter Clock wise and then turn the knob Counter clock wise.
Annexe:1 Turning Clockwise

Product Support Document

Calibrate Baro Encoder
Page 6 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 6 of 10
Annexe:2 Turning Counter Clockwise

Product Support Document

Calibrate Baro Encoder
Page 7 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 7 of 10
Annexe:3 End process

5 Validate functionality
5.1 Check encoder value
o Type VER 3 and Enter
o Turning knob to validate Digital Input (DI) make sure the value increments and
decrement correctly (No jumping)
o If you get jumping value that mean need to do Calibration Encoder
o Repeat step 4.2 one more time. If it was not resolve problem Encoder skips,
probably has serially problem with hardware Encoder switch.

Product Support Document

Calibrate Baro Encoder
Page 8 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 8 of 10
6 Troubleshoot

Condition A

Condition B

Product Support Document

Calibrate Baro Encoder
Page 9 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 9 of 10
6.1 Upcoming Contents
New content to be added to the list

Product Support Document

Calibrate Baro Encoder
Page 10 of 10 Revision 001 Last revised 2010-12-1526

Copyright © 2016 TRU Simulation + Training Canada Inc. All rights reserved.
This document also includes proprietary, trade secret and confidential information of TRU Simulation + Training Canada. No part of this document or of its
contents may be disclosed, translated, stored in a retrieval system, reproduced, or transmitted, in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise, without the express prior written consent of an authorized representative of TRU Simulation + Training Canada Inc.

Page 10 of 10