Scribd
Upload
56 views4 pages

Jagdpanther Building Guide EN

Uploaded by

kike mendo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
56 views4 pages

Jagdpanther Building Guide EN

Uploaded by

kike mendo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

https://www.youtube.

com/channel/UCMGMgo0nDydsYclif8VPc3A/videos
https://cults3d.com/en/users/kaja18/creations?fbclid=IwAR0dMBRWBT4ph6
jE1VWNbBh1D_Uj4IgnIXRG9MFB-tE36PSZzvdTgusCjMk

Construction instructions
scale: 1:10 width: 332 mm height:270 mm
length: 989 mm weight: 7000 g

The model is for personal use only.

What will be needed for construction:


ball bearings: 10x15x4 (53 pcs.), 15x21x4 (10 pcs)
tube of small diameter 2 cm on a flat from a bicycle
(2x)
https://www.rcprofi.cz/robitronic-stejnosmerny-motor-razer-540-
55t?_gl=1*19vdpv3*_up*MQ..&gclid=Cj0KCQiAgribBhDkARIsAASA5bs424juRTSmGLvZTS0
LTYvjYABiFzIhnsO1FY3d9du1suqjtSDSioIaAjQoEALw_wcB

two-way controller 45 60 A 2x
https://hobbyking.com/en_us/hobbyking-x-car-45a-brushed-car-
esc.html?queryID=b86370ec82555e2a04e124a690c7d5c3&objectID=48605&indexName=hbk_live_m
agento_en_us_products&___store=en_us

12 kg,
https://dratek.cz/arduino/122949-servo-mg995r-s-kovovymi-prevody-12kg-
360.html?gclid=Cj0KCQiAgribBhDkARIsAASA5buIQ-
stXTGq_V4yvLHROyY2cHm_8-HAgbp9KnjKkSllibnJnRVWqUEaAsl1EALw_wcB
1x
https://www.bighobby.cz/tower-pro-servo-mg90s-13-4g-0-08s-2-2kg-360-2/
1x Slip small Servo MG90S (360
https://www.bighobby.cz/tower-pro-servo-mg90s-13-4g-0-08s-2-2kg-360/

M2

8x

10x matka

M3
M3 matka

15
55
55
70x imbus
35

brass wire or welding wire 2 mm, length 60 mm - 174 pcs (belt couplings)
wire 1.6 mm to some hatches.
medium cyanoacrylate adhesive

belt gearbox
Here's what you'll need:
toothed belt 70 XL 037, width 9.4 mm (4 pcs.)
toothed belt 60 XL 037, width 9.4 mm (2 pcs.)

Recommended: It is better to print the plate where the


motor is assigned from PET-G. Part.6 pinion the same.

For a 20T motor, you need to adjust the power on your


radio by 40 %!

Part-2 large gear need to be printed 1 perimeter 100% fill. I


printed PET-G here

The prototype of the tank was printed on the Prusa MK3i printer
All parts have been printed and tested.
Print settings I used:
You can also use your own settings.
Support is needed on parts with the inscription suport!!!!!
As a slicer I prefer PrusaSlicer 2.5.0.
Printing support set by default.
For small parts, it is advisable to use a raft.
A grid fill pattern was applied to all parts.
Large parts, axles: standard setting Prusa slicer layer 0,2 mm
3 perimeters
30-80 % fill
extrusion width
outer 0,45 mm
inner 0,45 mm

Detailed parts:
layer 0,15 mm
3 perimeters
30-50 % fill
extrusion width
outer 0,45 mm
inner 0,45 mm

Transmission wheels:
layer 0,2 mm
Minimum 3 perimeters
60 % fill
Extrusion width:
external 0,44 mm
inner 0,45 mm

Gearbox drive axes:


0.2 mm layer
3 perimeters
80-90 % fill
Extrusion width:
outer 0,45 mm
inner 0,45 mm

Printing rounds with support is a necessary setting in the slicer:

You might also like