Aspirating Smoke Detection

Titanus ProSens, Titanus TopSens

Air samples are constantly taken in the monitored areas. By means
of a high performance suction mechanism, they are fed via a pipe
network to a detector chamber and checked there continuously. If
smoke particles are recorded, an alarm is activated immediately.

z High sensitivity early fire detection

z Suitable for a very wide range of applications
z For volumetric and objective surveillance
z Equipped with either one or two detector modules
z Various detector modules with different sensitivity levels
z Fire alarm at max. 0.8% obscuration per meter
z Fire alarm at max. 0.25% obscuration per meter
z Fire alarm at max. 0.05% obscuration per meter
z Sensitivity of each detector module can also be changed
z One fire alarm per detector module (Titanus ProSens only)
z Detection of pipe fractures or blockages of air sampling points

Additionally features of Titanus TopSens

z Three alarms per detector module
z Fire alarm at e.g. 0.25% obscuration per meter
z Action alarm at 66% of fire alarm smoke level
z Alert alarm at 33% of fire alarm smoke level
z 10-digit bar graph display

Building Technologies
Fire Safety & Security Products
Application

Titanus ProSens and Titanus TopSens are used when one encounters conditions
which hinder a standard solution or even make it impossible:
– Environmental conditions such as dirt, moisture, extreme cold, high voltage etc. in-
hibit the performance of the fire detectors.
– High halls and rooms with an intensive air change (e.g. air conditioning systems)
show a strong degree of smoke dilution, thereby delaying a rapid alarm response.
– Especially sensitive objects and a high concentration of valuable property (operating
data, data-dependant production means, software etc.) require particularly fast inter-
vention.
– In a production plant running 24 hours a day, the required maintenance work cannot
be performed on fire detectors if they are located in the production area.
– Access is often difficult or impossible in hollow spaces or vertical ducts.
– "Invisible" detection is desired in cultural buildings or design architecture.

Scope of application

ProSens TopSens
Clean rooms z
High open rooms | z
Air conditioning systems | z
Industrial production facilities z z
Refrigerated warehouses | z
Data processing service centres | z
Invisible security particularly appreciated in buildings with | z
cultural significance (churches, cathedrals, libraries, muse-
ums etc.) and with design oriented modern structures.
Rapid evacuation requiring early detection of the sources | z
of danger, which in an emergency allow rapid evacuation.
Risk of vandalism z z
Difficult access for maintenance e.g. areas of confidential- | z
ity, operating rooms, nuclear facilities, laboratories, high-
voltage facilities, penal institutions, false ceilings, false
floors, shafts, and other hard-to-access areas.
EMC-compatible z z
z Suitable | Depends on risk analysis

Examples for object and volumetric surveillance

Non-ventilated and power-ventilated devices cabi- Rooms such as storage areas, high-rack storage, elevator
nets such as distribution cabinets, switch cabinets, shafts, museums, deep-freeze storage, floor voids, ceiling
telephone switching equipment, measuring and voids, ducts, etc.
control units etc.
Pipe system : room

Pipe system : floor void

Siemens Building Technologies

Fire Safety & Security Products
Operating principle, installation, commissioning and maintenance

Titanus ProSens and Titanus TopSens take continuous air samples from the area
monitored via a tube system with defined air sampling points. An integrated smoke
detector detects an existing smoke concentration. Different detector modules with
various sensitivity levels can be selected and set according to the type of application.
Air flow to the detection device is constantly monitored and there will be a fault sig-
detector module
nalisation in case of blockage or rupture of the tube system.
Titanus ProSens Titanus TopSens
0.30 0.30

10
Fire alarm 0.25 0.25 Fire alarm
9
0.20 8 0.20
7
6 Action alarm
0.15 0.15
5
0.10 4 0.10
i 3 Alert alarm
0.05 0.05
2
smoke level
1
(% obsc./m) 0.00 0.00
Example: Titanus ProSens in comparison with Titanus TopSens.
Both have detector modules with a fire alarm sensitivity of 0.25% obsc./m.

Titanus ProSens and Titanus TopSens are mounted on walls or cabinets. By revers-
ing the device the connection socket can be positioned upward or downwards. By
removing the device cover, full access is provided to the detector modules without
any influence on the air flow monitoring. Easy commissioning is given due to micro-
processor controlled calibration of the air flow sensor and the easy set up of the sen-
sitivity. A diagnostic device is provided for maintenance and servicing which enables
rapid fault location.

Accessories

detonation preventation arc 90 °

device
steam trap

air sleeve
sampling
hose

ceiling lead through

special filter

air filter T-piece double screw joint

air sampling point

elbow 90°
testadapter

elbow 45°

end cap
reducer coup ling

aspiration reducing film sheet

air flow reducer

pipe with PG16 marking tape for AF

pipe cap (optional) internal thread

Siemens Building Technologies

Fire Safety & Security Products
Technical data

ProSens ProSens 2 TopSens TopSens 2

Detector modules 1 2 1 2
Operating voltage range 14 up to 30 V DC 14 up to 30 V DC 14 up to 30 V DC 14 up to 30 V DC
Nominal supply voltage 24 V DC 24 V DC 24 V DC 24 V DC
Current quiescent 200 mA (at 24 V) 220mA (at 24 V) 200 mA (at 24 V) 235mA (at 24 V)
Current alarm 210 mA (at 24 V) 240mA (at 24 V) 230 mA (at 24 V) 295mA (at 24 V)
Starting current limitation 300 mA 320mA 355 mA 385mA
Dimensions including 113 x 200 x 292mm 113 x 200 x 292mm 113 x 200 x 292mm 113 x 200 x 292mm
cable screw joints (H x W x D) (H x W x D) (H x W x D) (H x W x D)
Protection category IP 20 (IP 52*) IP 20 (IP 52*) IP 20 (IP 52*) IP 20 (IP 52*)
Temperature range -20 °C up to +60 °C -20 °C up to +60 °C -20 °C up to +60 °C -20 °C up to +60 °C
- deep freeze version -40 °C up to +60 °C -40 °C up to +60 °C -40 °C up to +60 °C -40 °C up to +60 °C
Humidity 10 up to 95 % rh 10 up to 95 % rh 10 up to 95 % rh 10 up to 95 % rh
- green operating display 1 1 1 1
- red alarm displays 1 2 3 6
- yellow fault display 1 1 1 1
- 10 digit bar display - - 1 2
Detector module highest level highest level highest level highest level
- DM-xx-80 0.80% obsc./m 0.80% obsc./m 0.80% obsc./m 0.80% obsc./m
- DM-xx-25 0.25% obsc./m 0.25% obsc./m 0.25% obsc./m 0.25% obsc./m
- DM-xx-05 0.05% obsc./m 0.05% obsc./m 0.05% obsc./m 0.05% obsc./m
Fire output (potential-free) 1 alarm signal 2 alarm signals 3 alarm signals 6 alarm signals
Fault signal (potential-free) 1 1 1 1
Load on contact/relay 1 A, 30 V DC 1 A, 30 V DC 1 A, 30 V DC 1 A, 30 V DC
max. 24 W max. 24 W max. 24 W max. 24 W
Terminal connections max. 1.5 mm² max. 1.5 mm² max. 1.5 mm² max. 1.5 mm²
Event memory yes yes yes yes
Remote displays 1 display possible 1 display possible 1 display possible 1 display possible
Pipe system **
- max. monitoring area *** 2.400m2 4.800 m2 2.400 m2 4.800 m2
- max. total length of pipe 180m 360m 180 m 360m
- max. air sampling points 24 48 24 48
Approvals VdS no. G202064 VdS no. G202064 VdS no. G203058 VdS no. G203058
*expandable **according to project planning guidelines; monitored area per air sampling point corresponds to a point detector according to VDE 0833
***depending on local codes and standards

Details for ordering

Type Part no Designation Weight

TP-1 AD-05-0455 Basic device Titanus ProSens 1.55 kg
TP-2 AD-05-1905 Basic device Titanus ProSens 2 1.55 kg
FS-TP-1 AD-10-1600 Front film sheet Titanus ProSens 0.012 kg
FS-TP-2 AD-10-1610 Front film sheet Titanus ProSens 2 0.012 kg
DM-TP-25-L AD-10-4150 Detector module Titanus ProSens (0.25% obsc. / m) 0.125 kg
DM-TP-05-L AD-10-4160 Detector module Titanus ProSens (0.05% obsc. / m) 0.125 kg
DM-TP-80-L AD-10-4165 Detector module Titanus ProSens (0.80% obsc. / m) 0.125 kg

TT/a AD-05-1220 Basic device Titanus TopSens 1.75 kg

FS-TT-1 AD-10-1650 Front film sheet Titanus TopSens 0.012 kg
FS-TT-2 AD-10-1660 Front film sheet Titanus TopSens 2 0.012 kg
DM-TT-25-L/a AD-10-4405 Detector module Titanus TopSens (0.25% obsc. / m) 0.125 kg
DM-TT-05-L/a AD-10-4412 Detector module Titanus TopSens (0.05% obsc. / m) 0.125 kg
DM-TT-80-L/a AD-10-4417 Detector module Titanus TopSens (0.80% obsc. / m) 0.125 kg
Siemens Switzerland Ltd
Building Technologies Group
International Headquaters
Fire Safety & Security Products
Gubelstrasse 21 © 2007 Copyright by
CH-6301 Zug Siemens Switzerland Ltd
Tel. +41 41 724 24 24
Fax +41 41 724 35 22 Data and design subject to change without notice.
www.sbt.siemens.com Supply subject to availability.
Document no. Manual -
Edition 02.2007 Section -