Scribd
Upload
14 views3 pages

Specs

Uploaded by

Sivarama Prasad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
14 views3 pages

Specs

Uploaded by

Sivarama Prasad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Specifications

Diversity Modem (S/W with Hardware)

I Modem
Sl. No. Parameters Specifications
1 IF interface 70 MHz ; 50 ohms
2 Transmit channels 2
3 Receiver channels 4
4 Modulation BPSK, QPSK
5 IF Bandwidth (1 dB) 12 MHz (for rates above 8 MBps)
7 MHz (for rates upto 8 Mbps)
6 Transmit power 0 dBm typical at both Tx ports (Without automatic link
power control in transmitter path)
7 Receiver Dynamic range +10 t0 -10 dBm (Linear operational)
+15 dBm max without damage
8 Data rate Upto 20 Mbps with FEC
22 Mbps without FEC
9 Data channel interface Ethernet 100base T IPV6
10 Channel health monitoring Integrated BER tester with embedded test sequence
11 Monitor and control port RS-232
12 Network management interface Ethernet (SNMP with GUI)
13 Front panel Operator control and status indication (Display,
Keypad and LEDs)
14 FEC Viterbi and/or TPC and/or LDPC or any suitable (user
selectable rates)
15 Automatic link power control 0-20 dB attenuator
Automatic based on received power of remote
modem
16 Diversity Combining Dual and quad digital diversity combining using MRC
or better technique
17 Eb/No Without FEC, 9dB for 1E-6 BER with quad diversity
With FEC 3.5 dB for 1E-6 BER (12 MHz, 1 dB BW)
with quad diversity
18 Troposcatter performance Multipath adaptive channel equalization for all four
receive channels
Dispersion expected upto 2σ/T=3 or better
19 Alarms Front panel LED / Alphanumeric display

20 Redundancy Through a Hot Standby switch (Note : Modem to work


independently without switch also)
21 10 MHz Ext. clock (in addition to SMA (Female), 50 Ohm, 0 dBm typical
internal)
22 IF connectors (4+2) SMA (female), 50 ohms, 6 nos.
23 Data connectors Suitable connectors ( D type)
24 Power supply 230 +/- 10% 47-60 Hz AC, Single phase
25 Height 2U or smaller
26 Width 19” rack mount
27 Weight Less than 10 Kgs
28 Cooling Fan on rear side
II Hot Standby Switch
Sl. No. Parameter Specifications
1 Hardware Min 8 bit Microcontroller based design
2 Switching On major alarm / switchable sensed on Monitor and
switch port
3 Indication Master / Slave indication through LED
4 Alarms Front panel LED/Buzzer
5 Rx IF (4 nos.) from Down Passive divider network
convertor
6 Tx IF (2 nos.) to Up convertor Passive combiner network
7 IF connectors (4*3 + 2*3) SMA (female), 50 ohm, 18 nos.
8 Data connectors Suitable connector (D type)
9 Power supply (1+1) 220 +/- 10% 47-60 Hz, Single phase
10 Height 1U or smaller
11 Width 19” rack mount
12 Weight Less than 2 Kg

III Environmental Requirements


Sl. No. Parameter Specifications
1 Operating temperature 0 to 50 deg
2 Storage temperature -20 to +70 deg C
3 Damp heat 40 deg ± 2 deg C Relative humidity ≥ 95 %
4 Vibration From 5 to 8 Hz ± 6 mm Const displacement
From 8 to 500 Hz ±15 m/s² Constant acceleration
5 Bump Peak acceleration 40 m/ s²
Pulse duration 6 ms
No. of bumps 1000 ± 10
Repetition rate 1 to 3 bumps /s

IV EMI/EMC (As per MIL STD 461 E)


1 CE 102 Power supply leads
2 CS 101 Power supply leads
3 CS 104 Rejection of undesired signals
4 RE 102 E field emissions

V Monitor & Control Data Console


Sl. No. Parameter Specifications
1 Processor Intel core i7, 3.5 Ghz, 8Mb
2 Operating System Windows 7, 32 bit
3 Memory 8 GB DDR3, 1600 MHz
4 Video card 2 GB
5 Display 15.6 cm LED
6 Hard disk 1TB SATA
7 Connectivity Ethernet/WLAN/Bluetooth

Page 2 of 3
Functions
1) Equalization / Diversity combining
2) Time tracking
3) Frequency tracking
4) Automatic Gain Control (AGC)

Data Interface
User Data channels
RS 422 and HSSI Interface
100 Base T Ethernet interface
Digital Service channels
Tropo FEC Turbo product code FEC
Adaptive Link Power control
Automatic Redundant Switching

Operating Modes
Monitor – Summary – local, remote
Alarms
Modem A – current, Historical
View, clear
Modem B – current, Historical
View, clear
RSL
Temp
AGC
TX APC
BERT
FAN

Configuration
Setup
Maintenance
Diagnostics
Operation via additional interfaces
Monitor and control
Ethernet interface
GUI interface
SNMP interface

Page 3 of 3

You might also like