Revision

Indication
LEGEND ALTERNATE VENTURI DETAIL STANDARD DRAWING
R UOP ENGINEERING DEPARTMENT 6-116-9
GATE VALVE
(WHEN VENTURI IS SPECIFIED)
ON.

DATE 06APR17
O
W ORIFICE METER PIPING ASSEMBLIES
SSI

GLOBE VALVE L STATUS REAFFIRMED

F
VALVING AND IMPULSE LIQUID, STEAM OR CONDENSABLE VAPOR SERVICE SPONSOR RED
TTEN PERM I

PIPING AS PER ORIFICE (METER LOCATED NEAR AND BELOW ORIFICE -FOR ASME FLANGE CLASS 300 AND 600)
NEEDLE VALVE APPROVED MJM
INSTALLATION.
•" SOLID
H - HIGH PRESSURE TAP
TUBING AND MANIFOLD
S W RI

L - LOW PRESSURE TAP

P - PLUGGED
THOUT UOP'

PIPE STRAP
(NOTE 5) 2" INSTRUMENT PROCESS
OW
PIPE MULTIPLE TRANSMITTERS DETAIL FL MOUNTING

SUPPORT PIPE
SCLOSED TO OTHERS W I

•" S
MI
PLUG NI
PIPE STRAP MU
M
(NOTE 5) TEST TEST
P P

2'-0" (600)
OW •" TU

MAXIMUM
HORIZONTAL
FL 2" INSTRUMENT

MOUNTING SUPPORT PIPE ORIFICE TAPS

INSTRUMENT

 •" H
5 VALVE MANIFOLD
CATED,OR DI

MI L
SOLID NI DIFFERENTIAL
MU DETAIL
PLUG M PRESSURE 5 VALVE MANIFOLD

INSTRUMENT (SEE DETAIL)

L
2'-0" (600)

2' H
MAXIMUM

-0 PIPE
AL AND M UST NOT BE USED FOR ANY PURPOSE,DUPLI

"
MA (6
XI 00 •" SO
HORIZONTAL
MU )
M PLUG

MAXIMUM
ORIFICE TAPS DIFFERENTIAL

2'-0"

(600)
PRESSURE
NOTE 6 INSTRUMENT
) •"
00 NOTE 4
•" (6
" M •" TU
-0 MU
2' XI L
A H
M
SCREWED CAP NOTE 12

FLOW
DO NOT SEAL SLOPE 1" PER FOOT

WELD (80mm PER METER)

5 VALVE MANIFOLD
MINIMUM
(SEE DETAIL)
PIPE STRAP
(NOTE 5)

MI DIFFERENTIAL
NI
2" INSTRUMENT MU PRESSURE
SCREWED CAP M
•" PIPE MOUNTING
DO NOT SEAL INSTRUMENT
2'-0" (600)

SUPPORT PIPE
•" SOLID WELD
MAXIMUM
DENTI

)
00
(6
" M •"
S CONFI

-0 MU NOTES:
2' XI
MA
DIFFERENTIAL
1. THE USE OF TUBING INSTEAD OF PIPE SHALL BE IN ACCORDANCE WITH UOP STANDARD SPECIFICATION 8-11 PIPING.
•"
S DOCUM ENT I

NOTE 12 PRESSURE
FLOW

2. DO NOT SEAL WELD SCREWED CONNECTIONS AT INSTRUMENT.

INSTRUMENT
3. PIPE AND NIPPLES BETWEEN FITTINGS SHALL BE OF MINIMUM LENGTH.
NOTE 6
4. USE FLANGES FOR SOCKET WELD PIPING AND UNION FOR SCREWED PIPING. NOT REQUIRED WHEN

USING REMOVABLE MOUNTING ADAPTORS ON INSTRUMENT BODY.

TUBING
N THI

PIPE STRAP 5. ALTERNATE MOUNTING: SUPPORT INSTRUMENT FROM ADJACENT PIPE RACK, GRADE, GRATING, OR FROM STRUCTURAL

(NOTE 5) STEEL. INSTALLATION SHALL ALLOW FOR PROCESS THERMAL EXPANSION OF PIPING.
ON I

H MINIMUM 6. PROVIDE UNION FOR SCREWED PIPING ONLY.

L •"
NFORM ATI

2" INSTRUMENT 1'

- 7. ORIFICE FLANGE TAPS AND PLUGS SHALL BE SEAL WELDED.
MOUNTING (3 0"
00
) 8. CAPPED TEES AT ORIFICE FLANGE SHALL BE ACCESSIBLE FOR REAMING.
SUPPORT PIPE
9. FOR INSTALLATIONS WHERE TWO TRANSMITTERS ARE REQUIRED, EACH TRANSMITTER SHALL BE INSTALLED
•"
AL -THE I

NOTE 4 FROM ITS OWN SET OF ORIFICE TAPS IN ACCORDANCE WITH THIS DRAWING.

10. EACH TRANSMITTER SHALL HAVE ITS OWN SET OF ISOLATING (•" GATE) VALVES FOR INSTALLATIONS WH
SCREWED CAP
MORE THAN ONE TRANSMITTER IS REQUIRED TO BE INSTALLED FROM ONE SET OF ORIFICE TAPS.
(DO NOT
DENTI

SEAL WELD) 11. ALL GLOBE AND GATE VALVES ARE

12. UPFLOW IS PERMITTED FOR LIQUIDS THAT ARE NOT NEAR THEIR BUBBLE POINTS. UPFLOW IS NOT
CONFI

RECOMMENDED FOR STEAM AND CONDENSABLE VAPORS.

TUBING
13. DIMENSIONS SHOWN IN PARENTHESES ARE IN MILLIMETERS.

QUALTRAX 11495