Instrumentation & Control

Process Control Fundamentals

Table of Contents
Introduction..................................................................................................................................................... 1 Performance Objective ............................................................................................................................. 1 The Importance of Process Control ............................................................................................................... 1 Learning Objectives.................................................................................................................................. 1 The Importance of Process Control................................................................................................................. 2 Process...................................................................................................................................................... 2 Process Control ........................................................................................................................................ 2 Reduce Variability ............................................................................................................................. 2 Increase Efficiency ............................................................................................................................ 3 Ensure Safety ..................................................................................................................................... 3 Control Theory Basics .................................................................................................................................... 4 Learning Objectives.................................................................................................................................. 4 The Control Loop............................................................................................................................................. 5 Three Tasks...............................................................................................................................................5 Process Control Terms ....................................................................................................................................6 Process Variable.......................................................................................................................................6 Setpoint .....................................................................................................................................................6 Measured Variables, Process Variables, and Manipulated Variables.....................................................7 Error .........................................................................................................................................................7 Offset.........................................................................................................................................................8 Load Disturbance .....................................................................................................................................8 Control Algorithm.....................................................................................................................................8 Manual and Automatic Control ................................................................................................................9 Closed and Open Control Loops ..............................................................................................................10 Components of Control Loops and ISA Symbology ...................................................................................... 11 Learning Objectives.................................................................................................................................. 11 Control Loop Equipment and Technology....................................................................................................... 12 Primary Elements/Sensors........................................................................................................................ 12 Transducers and Converters..................................................................................................................... 13 Transmitters.............................................................................................................................................. 13 Signals ...................................................................................................................................................... 14 Pneumatic Signals ............................................................................................................................. 14 Analog Signals................................................................................................................................... 14 Digital Signals ................................................................................................................................... 15 Indicators.................................................................................................................................................. 15 Recorders.................................................................................................................................................. 16 Controllers................................................................................................................................................ 16 Correcting Elements/Final Control Elements .......................................................................................... 18 Actuators................................................................................................................................................... 18

Fundamentals of Control
2006 PAControl.com

ii

www.PAControl.com

Table of Contents
ISA Symbology ................................................................................................................................................. 9 1 Symbols ................................................................................................................................................... 20 Pumps .............................................................................................................................................. 21 Piping and Connections .................................................................................................................. 22 Identification Letters............................................................................................................................... 23 Tag Numbers........................................................................................................................................... 23 ISA Symbology Review ........................................................................................................................... 26 Controller Algorithms and Tuning ...............................................................................................................27 Learning Objectives.................................................................................................................................27 Controller Algorithms.....................................................................................................................................28 Discrete Controllers ................................................................................................................................28 Multistep Controllers................................................................................................................................29 Continuous Controllers ............................................................................................................................29 Why controllers need tuning?...........................................................................................................................31 Gain ..........................................................................................................................................................31 Proportional Mode ..........................................................................................................................................33 Proportional Gain ....................................................................................................................................33 Proportional Band ....................................................................................................................................33 Limits of Proportional action ...................................................................................................................34 Determining the Controller Output..........................................................................................................34 Proportional Action- Closed Loop........................................................................................................... 35 . Integral Mode ................................................................................................................................................. 37 Integral Action ........................................................................................................................................ 37 Open Loop Analysis................................................................................................................................ 37 Closed Loop Analysis ............................................................................................................................. 38 Reset Windup .......................................................................................................................................... 39 Summary ................................................................................................................................................. 40 Derivative Mode .............................................................................................................................................. 41 Derivative Action .................................................................................................................................... 41 Rate Summary......................................................................................................................................... 44

Process Control Loops.....................................................................................................................................46 Learning Objectives..................................................................................................................................46 Single Control Loops .......................................................................................................................................47 Feedback Control .....................................................................................................................................47 Examples Of Single Control Loops..................................................................................................................48 Pressure Control Loops............................................................................................................................49 Flow Control Loops..................................................................................................................................49 Level Control Loops .................................................................................................................................50 Temperature Control Loops .....................................................................................................................51

iii

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Table of Contents
Multi-Variable / Advanced Control Loops ......................................................................................................52 Multivariable Loops .................................................................................................................................52 Feedforward Control ................................................................................................................................53 Feedforward plus Feedback .....................................................................................................................54 Cascade Control ..................................................................................................................................... 55 Batch Control ......................................................................................................................................... 56 Ratio Control .......................................................................................................................................... 56 Selective Control..................................................................................................................................... 57 Fuzzy Control ......................................................................................................................................... 57

Fundamentals of Control
2006 PAControl.com

iv

www.PAControl.com

Introduction
Control in process industries refers to the regulation of all aspects of the process. Precise control of level, temperature, pressure and flow is important in many process applications. This module introduces you to control in process industries, explains why control is important, and identifies different ways in which precise control is ensured. The following five sections are included in this module: The importance of process control Control theory basics Components of control loops and ISA symbology Controller algorithms and tuning Process control systems As you proceed through the module, answer the questions in the activities column on the right side of each page. Also, note the application boxes (double-bordered boxes) located throughout the module. Application boxes provide key information about how you may use your baseline knowledge in the field. When you see the workbook exercise graphic at the bottom of a page, go to the workbook to complete the designated exercise before moving on in the module. Workbook exercises help you measure your progress toward meeting each sections learning objectives.

PERFORMANCE OBJECTIVE
After completing this module, you will be able to determine needed control loop components in specific process control applications.

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

The Importance of Process Control

Refining, combining, handling, and otherwise manipulating fluids to profitably produce end products can be a precise, demanding, and potentially hazardous process. Small changes in a process can have a large impact on the end result. Variations in proportions, temperature, flow, turbulence, and many other factors must be carefully and consistently controlled to produce the desired end product with a minimum of raw materials and energy. Process control technology is the tool that enables manufacturers to keep their operations running within specified limits and to set more precise limits to maximize profitability, ensure quality and safety.

LEARNING OBJECTIVES
After completing this section, you will be able to: Define process Define process control Describe the importance of process control in terms of variability, efficiency, and safety

Note: To answer the activity questions the Hand Tool (H) should be activated.

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

The Importance of Process Control

The Importance of Process Control Activities PROCESS

Process as used in the terms process control and process industry, refers to the methods of changing or refining raw materials to create end products. The raw materials, which either pass through or remain in a liquid, gaseous, or slurry (a mix of solids and liquids) state during the process, are transferred, measured, mixed, heated or cooled, filtered, stored, or handled in some other way to produce the end product. Process industries include the chemical industry, the oil and gas industry, the food and beverage industry, the pharmaceutical industry, the water treatment industry, and the power industry. 1. Process is defined as the changing or refining of raw materials that pass through or remain in a liquid, gaseous, or slurry state to to create end products.

PROCESS CONTROL
Process control refers to the methods that are used to control process variables when manufacturing a product. For example, factors such as the proportion of one ingredient to another, the temperature of the materials, how well the ingredients are mixed, and the pressure under which the materials are held can significantly impact the quality of an end product. Manufacturers control the production process for three reasons: Reduce variability Increase efficiency Ensure safety Reduce Variability Process control can reduce variability in the end product, which ensures a consistently high-quality product. Manufacturers can also save money by reducing variability. For example, in a gasoline blending process, as many as 12 or more different components may be blended to make a specific grade of gasoline. If the refinery does not have precise control over the flow of the separate components, the gasoline may get too much of the high-octane components. As a result, customers would receive a higher grade and more expensive gasoline than they paid for, and the refinery would lose money. The opposite situation would be customers receiving a lower grade at a higher price.

2. Which of these industries are examples of the process industry? Select all options that apply.
1 2 3 4 5

Pharmaceutical Satellite Oil and Gas Cement Power

Fundamentals of Control
2006 PAControl.com.

www.PAControl.com

The Importance of Process Control

product padding to meet required product specifications. Padding refers to the process of making a product of higher-quality than it needs to be to meet specifications. When there is variability in the end product (i.e., when process control is poor), manufacturers are forced to pad the product to ensure that specifications are met, which adds to the cost. With accurate, dependable process control, the setpoint (desired or optimal point) can be moved closer to the actual product specification and thus save the manufacturer money.
PV limit to ensure quality

The Importance of Process Control Reducing variability can also save money by reducing the need for Activities
3. What are the main reasons for manufacturers to control a process? Select all options that apply.
1 2 3 4
PV limit to ensure quality PV Setpoint

Reduce variability Ensure safety Reduce costs Increase efficiency Increase productivity

Low Variability PV Setpoint

High Variability

Increase Efficiency Some processes need to be maintained at a specific point to maximize efficiency. For example, a control point might be the temperature at which a chemical reaction takes place. Accurate control of temperature ensures process efficiency. Manufacturers save money by minimizing the resources required to produce the end product. Ensure Safety A run-away process, such as an out-of-control nuclear or chemical reaction, may result if manufacturers do not maintain precise control of all of the processg variables. The consequences of a run-away process can be catastrophic. Precise process control may also be required to ensure safety. For example, maintaining proper boiler pressure by controlling the inflow of air used in combustion and the outflow of exhaust gases is crucial in preventing boiler implosions that can clearly threaten the safety of workers.
COMPLETE WORKBOOK EXERCISE - THE IMPORTANCE OF PROCESS CONTROL

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

This section presents some of the basic concepts of control and provides a foundation from which to understand more complex control processes and algorithms later described in this module. Common terms and concepts relating to process control are defined in this section.

LEARNING OBJECTIVES
After completing this section, you will be able to: Define control loop Describe the three tasks necessary for process control to occur: Measure Compare Adjust Define the following terms: Process variable Setpoint Manipulated variable Measured variable Error Offset Load disturbance Control algorithm List at least five process variables that are commonly controlled in process measurement industries At a high level, differentiate the following types of control: Manual versus automatic feedback control Closed-loop versus open-loop control

Note: To answer the activity questions the Hand Tool (H) should be activated.

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

The Control Loop

Imagine you are sitting in a cabin in front of a small fire on a cold winter evening. You feel uncomfortably cold, so you throw another log on the fire. Thisis an example of a control loop. In the control loop, a variable (temperature) fell below the setpoint (your comfort level), and you took action to bring the process back into the desired condition by adding fuel to the fire. The control loop will now remain static until the temperature again rises above or falls below your comfort level.

Activities
1. The three tasks associated with any control loop are measurement, comparison, and adjustment. Is this statement true or false?

THREE TASKS
Control loops in the process control industry work in the same way, requiring three tasks to occur: Measurement Comparison Adjustment In Figure 7.1, a level transmitter (LT) measures the level in the tank and transmits a signal associated with the level reading to a controller (LIC). The controller compares the reading to a predetermined value, in this case, the maximum tank level established by the plant operator, and finds that the values are equal. The controller then sends a signal to the device that can bring the tank level back to a lower levela valve at the bottom of the tank. The valve opens to let some liquid out of the tank. Many different instruments and devices may or may not be used in control loops (e.g., transmitters, sensors, controllers, valves, pumps), but the three tasks of measurement, comparison, and adjustment are always present.

LIC

Maximum level

LT

A Simple Control Loop

Fundamentals of Control
2006 PAControl.com.

www.PAControl.com

Control Theory Basics

Process Control Terms

As in any field, process control has its own set of common terms that you should be familiar with and that you will use when talking about control technology.

Activities
2. A process variable is a condition that can change the process in some way.

PROCESS VARIABLE
A process variable is a condition of the process fluid (a liquid or gas) that can change the manufacturing process in some way. In the example of you sitting by the fire, the process variable was temperature. In the example of the tank in Figure 7.1, the process variable is level. Common process variables include: Pressure Flow Level Temperature Density Ph (acidity or alkalinity) Liquid interface (the relative amounts of different liquids that are combined in a vessel) Mass Conductivity

SETPOINT
The setpoint is a value for a process variable that is desired to be maintained. For example, if a process temperature needs to kept within 5 C of 100 C, then the setpoint is 100 C. A temperature sensor can be used to help maintain the temperature at setpoint. The sensor is inserted into the process, and a contoller compares the temperature reading from the sensor to the setpoint. If the temperature reading is 110 C, then the controller determines that the process is above setpoint and signals the fuel valve of the burner to close slightly until the process cools to 100 C. Set points can also be maximum or minimum values. For example, level in tank cannot exceed 20 feet.

3. Imagine you are in a cabin in front of a small fire on a cold winter evening. You feel uncomfortably cold, so you throw another log into the fire. In this scenario, the process variable is temperature. Is this true or false?

4. If the level of a liquid in a tank must be maintained within 5 ft of 50 ft, what is the liquids setpoint?

1 2 3 4

45 ft 55 ft 5 ft 50 ft

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

Process Control Terms

MEASURED VARIABLES, PROCESS VARIABLES, AND MANIPULATED VARIABLES
In the temperature control loop example, the measured variable is temperature, which must be held close to 100 C. In this example and in most instances, the measured variable is also the process variable. The measured variable is the condition of the process fluid that must be kept at the designated setpoint. Sometimes the measured variable is not the same as the process variable. For example, a manufacturer may measure flow into and out of a storage tank to determine tank level. In this scenario, flow is the measured variable, and the process fluid level is the process variable. The factor that is changed to keep the measured variable at setpoint is called the manipulated variable. In the example described, the manipulated variable would also be flow (Figure 7.2).
Setpoint
Process variable or measured variable

Activities
5. ____________________ is a sustained deviation of the process variable from the setpoint.

6. A load disturbance is an undesired change in one of the factors that can affect the setpoint. Is this statement true or false?

Controller

Manipulated variable

Variables

ERROR
Error is the difference between the measured variable and the setpoint and can be either positive or negative. In the temperature control loop example, the error is the difference between the 110 C measured variable and the 100 C setpointthat is, the error is +10 C. The objective of any control scheme is to minimize or eliminate error. Therefore, it is imperative that error be well understood. Any error can be seen as having three major components. These three components are shown in the figure on the folowing page Magnitude The magnitude of the error is simply the deviation between the values of the setpoint and the process variable. The magnitude of error at any point in time compared to the previous error provides the basis for determining the change in error. The change in error is also an important value.

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

Process Control Terms

Duration Duration refers to the length of time that an error condition has existed. Rate Of Change The rate of change is shown by the slope of the error plot.

Activities

Rate of Change of Error (Slope of Error Plot) PV Magnitude of Error

Duration

SP

Components of Error

OFFSET
Offset is a sustained deviation of the process variable from the setpoint. In the temperature control loop example, if the control system held the process fluid at 100.5 C consistently, even though the setpoint is 100 C, then an offset of 0.5 C exists.

LOAD DISTURBANCE
A load disturbance is an undesired change in one of the factors that can affect the process variable. In the temperature control loop example, adding cold process fluid to the vessel would be a load disturbance because it would lower the temperature of the process fluid.

CONTROL ALGORITHM
A control algorithm is a mathematical expression of a control function. Using the temperature control loop example, V in the equation below is the fuel valve position, and e is the error. The relationship in a control algorithm can be expressed as:

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

Process Control Terms

V = f ( e)

Activities
7. Automatic control systems are control operations that involve human action to make adjustment. Is this statement true or false?

The fuel valve position (V) is a function (f) of the sign (positive or negative) of the error (Figure 7.3).
Summing block Process variable Error Manipulated variable

f(e)

Valve position

Feedback

Algorithm Example

Control algorithms can be used to calculate the requirements of much more complex control loops than the one described here. In more complex control loops, questions such as How far should the valve be opened or closed in response to a given change in setpoint? and How long should the valve be held in the new position after the process variable moves back toward setpoint? need to be answered.

MANUAL AND AUTOMATIC CONTROL

Before process automation, people, rather than machines, performed many of the process control tasks. For example, a human operator might have watched a level gauge and closed a valve when the level reached the setpoint. Control operations that involve human action to make an adjustment are called manual control systems. Conversely, control operations in which no human intervention is required, such as an automatic valve actuator that responds to a level controller, are called automatic control systems.

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Control Theory Basics

Process Control Terms

CLOSED AND OPEN CONTROL LOOPS
A closed control loop exists where a process variable is measured, compared to a setpoint, and action is taken to correct any deviation from setpoint. An open control loop exists where the process variable is not compared, and action is taken not in response to feedback on the condition of the process variable, but is instead taken without regard to process variable conditions. For example, a water valve may be opened to add cooling water to a process to prevent the process fluid from getting too hot, based on a pre-set time interval, regardless of the actual temperature of the process fluid.

Activities
8. Under what circumstances does an open control loop exist? Select all options that apply.
1 2 3 4 5

Process variable is not measured Process variable is not compared Process variable is measured and compared to a setpoint Action is taken without regard to process variable conditions Action is taken with regard to process variable conditions

COMPLETE WORKBOOK EXERCISE - CONTROL THEORY BASICS

10

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

This section describes the instruments, technologies, and equipment used to develop and maintain process control loops. In addition, this section describes how process control equipment is represented in technical drawings of control loops.

LEARNING OBJECTIVES
After completing this section, you will be able to: Describe the basic function of and, where appropriate, the basic method of operation for the following control loop components: Primary element/sensor Transducer Converter Transmitter Signal Indicator Recorder Controller Correcting element/final control element Actuator List examples of each type of control loop component listed above State the advantages of 420 mA current signals when compared with other types of signals List at least three types of final control elements, and for each one: Provide a brief explanation of its method of operation Describe its impact on the control loop List common applications in which it is used Given a piping and instrumentation drawing (P&ID), correctly label the: Instrument symbols (e.g., control valves, pumps, transmitters) Location symbols (e.g., local, panel-front) Signal type symbols (e.g., pneumatic, electrical) Accurately interpret instrument letter designations used on P&IDs

Fundamentals of Control
2006 PAControl.com

11

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology The previous section described the basic elements of control as Activities
measurement, comparison, and adjustment. In practice, there are instruments and strategies to accomplish each of these essential tasks. In some cases, a single process control instrument, such as a modern pressure transmitter, may perform more than one of the basic control functions. Other technologies have been developed so that communication can occur among the components that measure, compare, and adjust. 1. Identify three examples of a primary element/sensors in process control? Select all options that apply.
1 2 3 4 5

PRIMARY ELEMENTS/SENSORS
In all cases, some kind of instrument is measuring changes in the process and reporting a process variable measurement. Some of the greatest ingenuity in the process control field is apparent in sensing devices. Because sensing devices are the first element in the control loop to measure the process variable, they are also called primary elements. Examples of primary elements include: Pressure sensing diaphragms, strain gauges, capacitance cells Resistance temperature detectors (RTDs) Thermocouples Orifice plates Pitot tubes Venturi tubes Magnetic flow tubes Coriolis flow tubes Radar emitters and receivers Ultrasonic emitters and receivers Annubar flow elements Vortex sheddar Primary elements are devices that cause some change in their property with changes in process fluid conditions that can then be measured. For example, when a conductive fluid passes through the magnetic field in a magnetic flow tube, the fluid generates a voltage that is directly proportional to the velocity of the process fluid. The primary element (magnetic flow tube) outputs a voltage that can be measured and used to calculate the fluids flow rate. With an RTD, as the temperature of a process fluid surrounding the RTD rises or falls, the electrical resistance of the RTD increases or decreases a proportional amount. The resistance is measured, and from this measurement, temperature is determined.

Resistance Temperature Detectors Thermocouples Control Valve Converter Pitot tubes

2. Primary elements will not make direct contact with the process fluid. Is this statement true or false?

12

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology

TRANSDUCERS AND CONVERTERS
A transducer is a device that translates a mechanical signal into an electrical signal. For example, inside a capacitance pressure device, a transducer converts changes in pressure into a proportional change in capacitance. A converter is a device that converts one type of signal into another type of signal. For example, a converter may convert current into voltage or an analog signal into a digital signal. In process control, a converter used to convert a 420 mA current signal into a 315 psig pneumatic signal (commonly used by valve actuators) is called a current-to-pressure converter.

Activities
3. A ____________ is a device that translates a mechanical signal into an electrical signal.

TRANSMITTERS
A transmitter is a device that converts a reading from a sensor or transducer into a standard signal and transmits that signal to a monitor or controller. Transmitter types include: Pressure transmitters Flow transmitters Temperature transmitters Level transmitters Analytic (O2 [oxygen], CO [carbon monoxide], and pH) transmitters
4. A transmitter is a device that converts a reading from a transducer into a standard signal and transmits that signal to a monitor or controller. Is this statement true or false?

Fundamentals of Control
2006 PAControl.com

13

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology SIGNALS Activities

There are three kinds of signals that exist for the process industry to transmit the process variable measurement from the instrument to a centralized control system. 1. Pneumatic signal 2. Analog signal 3. Digital signal Pneumatic Signals Pneumatic signals are signals produced by changing the air pressure in a signal pipe in proportion to the measured change in a process variable. The common industry standard pneumatic signal range is 315 psig. The 3 corresponds to the lower range value (LRV) and the 15 corresponds to the upper range value (URV). Pneumatic signalling is still common. However, since the advent of electronic instruments in the 1960s, the lower costs involved in running electrical signal wire through a plant as opposed to running pressurized air tubes has made pneumatic signal technology less attractive. Analog Signals The most common standard electrical signal is the 420 mA current signal. With this signal, a transmitter sends a small current through a set of wires. The current signal is a kind of gauge in which 4 mA represents the lowest possible measurement, or zero, and 20 mA represents the highest possible measurement. For example, imagine a process that must be maintained at 100 C. An RTD temperature sensor and transmitter are installed in the process vessel, and the transmitter is set to produce a 4 mA signal when the process temperature is at 95 C and a 20 mA signal when the process temperature is at 105 C. The transmitter will transmit a 12 mA signal when the temperature is at the 100 C setpoint. As the sensors resistance property changes in response to changes in temperature, the transmitter outputs a 420 mA signal that is proportionate to the temperature changes. This signal can be converted to a temperature reading or an input to a control device, such as a burner fuel valve. Other common standard electrical signals include the 15 V (volts) signal and the pulse output. 5. Identify the signal types that are used in the process control industry? Select all options that apply.
1 2 3 4 5

Hydraulic signals Digital signals Analog signals Pneumatic signals Electro-magnetic signals

14

Fundamentals of Control

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology Digital Signals Activities

Digital signals are the most recent addition to process control signal technology. Digital signals are discrete levels or values that are combined in specific ways to represent process variables and also carry other information, such as diagnostic information. The methodology used to combine the digital signals is referred to as protocol. Manufacturers may use either an open or a proprietary digital protocol. Open protocols are those that anyone who is developing a control device can use. Proprietary protocols are owned by specific companies and may be used only with their permission. Open digital protocols include the HART (highway addressable remote transducer) protocol, FOUNDATION Fieldbus, Profibus, DeviceNet, and the Modbus protocol. (See Module 8: Communication Technologies for more information on digital communication protocols.) 6. The ___________ is a human-readable device that displays information about the process or the instrument it is connected to.

INDICATORS
While most instruments are connected to a control system, operators sometimes need to check a measurement on the factory floor at the measurement point. An indictor makes this reading possible. An indicator is a human-readable device that displays information about the process. Indicators may be as simple as a pressure or temperature gauge or more complex, such as a digital read-out device. Some indicators simply display the measured variable, while others have control buttons that enable operators to change settings in the field.

7. Which of the following are examples of a digital signal? Select all options that apply.
1 2 3 4 5

Profibus 4 - 20 mA 1-5v Fieldbus 3 - 15 psig

15

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology RECORDERS Activities

A recorder is a device that records the output of a measurement devices. Many process manufacturers are required by law to provide a process history to regulatory agencies, and manufacturers use recorders to help meet these regulatory requirements. In addition, manufacturers often use recorders to gather data for trend analyses. By recording the readings of critical measurement points and comparing those readings over time with the results of the process, the process can be improved. Different recorders display the data they collect differently. Some recorders list a set of readings and the times the readings were taken; others create a chart or graph of the readings. Recorders that create charts or graphs are called chart recorders.

8. A recorder is a device that records the ________________ of a measurement or control device.

CONTROLLERS
A controller is a device that receives data from a measurement instrument, compares that data to a programmed setpoint, and, if necessary, signals a control element to take corrective action. Local controllers are usually one of the three types: pneumatic, electronic or programmable. Contollers also commonly reside in a digital control system.
Computer-based central controller DCS Pneumatic, electronic, or programmable local controller

Transmitter

Single-loop controller

Valve

Power supply

Controller (CPU)

I/O card

Controllers

16

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology Controllers may perform complex mathematical functions to compare Activities
a set of data to setpoint or they may perform simple addition or subtraction functions to make comparisons. Controllers always have an ability to receive input, to perform a mathematical function with the input, and to produce an output signal. Common examples of controllers include: Programmable logic controllers (PLCs)PLCs are usually computers connected to a set of input/output (I/O) devices. The computers are programmed to respond to inputs by sending outputs to maintain all processes at setpoint. Distributed control systems (DCSs)DCSs are controllers that, in addition to performing control functions, provide readings of the status of the process, maintain databases and advanced man-machine-interface. 9. Which of the following have the ability to receive input, to perform a mathematical function with the input, and produce an output signal?
1 2 3 4

Actuators Transmitters Transducers Controllers

Setpoint P I D Analog Rack Mount Controller (Electronic)

10. Which of the following is the most common final control element in process control industries?

Pipestand Controller (Pneumatic or Electronic)

1 2 3 4

Agitator Pump motor Valve Louver

Single Loop Digital Converter (Electronic)

Distributed Control System (Electronic)

Types of Process Controllers

Fundamentals of Control
2006 PAControl.com

17

www.PAControl.com

Components of Control Loops and ISA Symbology

Control Loop Equipment and Technology Activities

11. _______________ is a part final control device that causes a physical change in the final control device when signaled to do so.
Smart Transmitter

Digital Valve Controller (Smart Positioner)

Smart Transmitter (Provides PID Output)

Types of Process Controllers

CORRECTING ELEMENTS/FINAL CONTROL ELEMENTS

The correcting or final control element is the part of the control system that acts to physically change the manipulated variable. In most cases, the final control element is a valve used to restrict or cut off fluid flow, but pump motors, louvers (typically used to regulate air flow), solenoids, and other devices can also be final control elements. Final control elements are typically used to increase or decrease fluid flow. For example, a final control element may regulate the flow of fuel to a burner to control temperature, the flow of a catalyst into a reactor to control a chemical reaction, or the flow of air into a boiler to control boiler combustion. In any control loop, the speed with which a final control element reacts to correct a variable that is out of setpoint is very important. Many of the technological improvements in final control elements are related to improving their response time.

ACTUATORS
An actuator is the part of a final control device that causes a physical change in the final control device when signalled to do so. The most common example of an actuator is a valve actuator, which opens or closes a valve in response to control signals from a controller. Actuators are often powered pneumatically, hydraulically, or electrically. Diaphragms, bellows, springs, gears, hydraulic pilot valves, pistons, or electric motors are often parts of an actuator system.

18

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
The Instrumentation, Systems, and Automation Society (ISA) is one of the leading process control trade and standards organizations. The ISA has developed a set of symbols for use in engineering drawings and designs of control loops (ISA S5.1 instrumentation symbol specification). You should be familiar with ISA symbology so that you can demonstrate possible process control loop solutions on paper to your customer. Figure 7.5 shows a control loop using ISA symbology. Drawings of this kind are known as piping and instrumentation drawings (P&ID).
SP

Activities
12. What does the acronym P&ID stand for?

1 2 3

FIC 123

TIC 123

Piping and Instrument Designing Piping and Instrumentation Drawing Process Control and Installation Drawing Proportional, Intergral and Derivative control

TY 123

YIC 123 TT 123

FT 123

Piping and Instrumentation Drawing (P&ID)

Fundamentals of Control
2006 PAControl.com

19

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
SYMBOLS
In a P&ID, a circle represents individual measurement instruments, such as transmitters, sensors, and detectors (Figure 7.6).
LOCATION

Activities
13. Which of the following is a symbol of a transmitter in an auxiliary location?

1
Control Room Auxiliary Field Not Accessible

Figure 7.6: Discrete Instruments

A single horizontal line running across the center of the shape indicates that the instrument or function is located in a primary location (e.g., a control room). A double line indicates that the function is in an auxiliary location (e.g., an instrument rack). The absence of a line indicates that the function is field mounted, and a dotted line indicates that the function or instrument is inaccessible (e.g., located behind a panel board). A square with a circle inside represents instruments that both display measurement readings and perform some control function (Figure 7.7). Many modern transmitters are equipped with microprocessors that perform control calculations and send control output signals to final control elements.
DISPLAY AND CONTROL TYPES

14. Which of the following is a symbol of a field-mounted control/display element?

Control Room Field Not Accessible Flow/ Square Root

Shared Control/Display Elements

A hexagon represents computer functions, such as those carried out by a controller (Figure 7.8).
Control Types

4
Control Room Auxiliary Field Not Accessible

Computer Functions (Controllers)

20

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
Activities
15. Which of the following is a symbol of a controller located behind a panel?

Fundamentals of Control
2006 PAControl.com

21

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
A square with a diamond inside represents PLCs (Figure 7.9).
PLC Types

Activities
16. The symbol displayed below denotes a PLC in a primary location. Is this statement true or false?

Control Room

Auxiliary

Field

Not accessible

PLCs

Two triangles with their apexes contacting each other (a bow tie shape) represent a valve in the piping. An actuator is always drawn above the valve (Figure 7.10).
Pneumatic valve Manual valve Electric valve

17. Which of the following is a symbol of a pneumatic valve?

Valves

Pumps Directional arrows showing the flow direction represent a pump (Figure 7.11).
2

Pumps

Fundamentals of Control
2006 PAControl.com

22

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
Piping and Connections Piping and connections are represented with several different symbols (Figure 7.12): A heavy solid line represents piping A thin solid line represents process connections to instruments (e.g., impulse piping) A dashed line represents electrical signals (e.g., 420 mA connections) A slashed line represents pneumatic signal tubes A line with circles on it represents data links Other connection symbols include capillary tubing for filled systems (e.g., remote diaphragm seals), hydraulic signal lines, and guided electromagnetic or sonic signals.
Piping

Activities
18. The symbols displayed below represent a data link and a process connection. Is this statement true or false?

Process connection

Electrical signal

Pneumatic signal

Data link

Capillary tubing for filled systems

Hydraulic signal line

Guided electromagnetic or sonic signal

Piping and Connection Symbols

23

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
IDENTIFICATION LETTERS
Identification letters on the ISA symbols (e.g., TT for temperature transmitter) indicate: The variable being measured (e.g., flow, pressure, temperature) The devices function (e.g., transmitter, switch, valve, sensor, indicator) Some modifiers (e.g., high, low, multifunction) Table 7.1 on page 26 shows the ISA identification letter designations. The initial letter indicates the measured variable. The second letter indicates a modifier, readout, or device function. The third letter usually indicates either a device function or a modifier. For example, FIC on an instrument tag represents a flow indicating controller. PT represents a pressure transmitter. You can find identification letter symbology information on the ISA Web site at http://www.isa.org.

Activities
19. The initial letter on an ISA symbol indicates the measured variable. Is this statement true or false?

20. What does the third letter on an ISA symbol indicate?

TAG NUMBERS
Numbers on P&ID symbols represent instrument tag numbers. Often these numbers are associated with a particular control loop (e.g., flow transmitter 123). See Figure 7.13.
Identification letters

1 2 3 4

Device function or a modifier Measured variable Readout Type of process fluid

FIC 123
Tag number

Identification Letters and Tag Number

Fundamentals of Control
2006 PAControl.com

24

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
Measured Variable

Modifier

Readout

Device Function

Modifier Activities

Analysis

Alarm

Burner, combustion

Users choice

Users choice

Users choice

Users choice

Control

Users choice

Differential

Voltage

Sensor (primary element)

Flow rate

Ration (fraction)

Users choice

Glass, viewing device

Hand

High

Electrical Current

Indication

Power

Scan

Time, time schedule

Time rate of change

Control station

Level

Light

Low

Users choice

Momentary

Middle, intermediate

Users choice

Users choice

Users choice

Users choice

Users choice

Orifice, restriction

Pressure, vacuum

Point, test connection

Quantity

Integrate, totalizer

Radiation

Record

Speed, frequency

Safety

Switch

Temperature

Transmit

Multivariable

Multifunction

Multifunction

Multifunction

Vibration, mechanical analysis

Valve, damper, louver

Weight, force

Well

Unclassified

X axis

Unclassified

Unclassified

Unclassified

Event, state, or presence

Y axis

Relay, compute, convert

Position, dimension

Z axis

Driver, actuator

ISA Identification Letters

25

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Components of Control Loops and ISA Symbology

ISA Symbology
ISA SYMBOLOGY REVIEW
Figure 7.14 shows the elements of ISA symbology used in a P&ID.
Flow indicating controller that performs a square root flow calculation (primary location)

Activities
Temperature indicating controller (field mounted)

21. In Figure 7.14, what kind of . signal is transmitted out from the temperature transmitter?

FIC 123

SP
Data link Electrical signal

1 2 3

TIC 123
PLC

Data link Mechanical signal Electrical signal Pneumatic signal

Flow transmitter
Temperature computer

TY 123

YIC 123
Pneumatic line

FT 123
Impulse Tubing
Pipe

TT 123
Temperature transmitter

Pneumatically actuated valve

Electrically actuated valve

P&ID with ISA Symbology

COMPLETE WORKBOOK EXERCISE - COMPONENTS OF CONTROL LOOPS AND ISA SYMBOLOGY

Fundamentals of Control
2006 PAControl.com

26

www.PAControl.com

Controller Algorithms and Tuning

The previous sections of this module described the purpose of control, defined individual elements within control loops, and demonstrated the symbology used to represent those elements in an engineering drawing. The examples of control loops used thus far have been very basic. In practice, control loops can be fairly complex. The strategies used to hold a process at setpoint are not always simple, and the interaction of numerous setpoints in an overall process control plan can be subtle and complex. In this section, you will be introduced to some of the strategies and methods used in complex process control loops.

LEARNING OBJECTIVES
After completing this section, you will be able to: Differentiate between discrete, multistep, and continuous controllers Describe the general goal of controller tuning. Describe the basic mechanism, advantages and disadvantages of the following mode of controller action: Proportional action Intergral action Derivative action Give examples of typical applications or situations in which each mode of controller action would be used. Identify the basic implementation of P, PI and PID control in the following types of loops: Pressure loop Flow loop Level loop Temperature loop

Note: To answer the activity questions the Hand Tool (H) should be activated.

Fundamentals of Control
2006 PAControl.com

27

www.PAControl.com

Controller Algorithms and Tuning

Controller Algorithms
The actions of controllers can be divided into groups based upon the functions of their control mechanism. Each type of contoller has advantages and disadvantages and will meet the needs of different applications. Grouped by control mechanism function, the three types of controllers are: Discrete controllers Multistep controllers Continuous controllers

Activities
1. Which one of the following is an everyday example of a discrete controller? Select the options that apply.
1 2 3 4

DISCRETE CONTROLLERS
Discrete controllers are controllers that have only two modes or positions: on and off. A common example of a discrete controller is a home hot water heater. When the temperature of the water in the tank falls below setpoint, the burner turns on. When the water in the tank reaches setpoint, the burner turns off. Because the water starts cooling again when the burner turns off, it is only a matter of time before the cycle begins again. This type of control doesnt actually hold the variable at setpoint, but keeps the variable within proximity of setpoint in what is known as a dead zone (Figure 7.15).

Refrigerator Electric iron Air conditioner Rice cooker

Dead zone

Process variable action

Control action

Discrete Control

28

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Controller Algorithms
MULTISTEP CONTROLLERS
Multistep controllers are controllers that have at least one other possible position in addition to on and off. Multistep controllers operate similarly to discrete controllers, but as setpoint is approached, the multistep controller takes intermediate steps. Therefore, the oscillation around setpoint can be less dramatic when multistep controllers are employed than when discrete controllers are used (Figure 7.16).

Activities
2. A controller with three or more set positions is called a continuous controller. Is this statement true or false?

Process variable action

Control action

Figure 7.16: Multistep Control Profile

CONTINUOUS CONTROLLERS
Controllers automatically compare the value of the PV to the SP to determine if an error exists. If there is an error, the controller adjusts its output according to the parameters that have been set in the controller. The tuning parameters essentially determine: How much correction should be made? The magnitude of the correction( change in controller output) is determined by the proportional mode of the controller. How long should the correction be applied? The duration of the adjustment to the controller output is determined by the integral mode of the controller How fast should the correction be applied? The speed at which a correction is made is determined by the derivative mode of the controller.

Fundamentals of Control
2006 PAControl.com

29

www.PAControl.com

Controller Algorithms and Tuning

Controller Algorithms
When there is an error, the controller makes a change in its output. It determines: How much? Proportional Mode How long? Integral Mode How fast? Derivative Mode
Setpoint LIC I/P P I D SP PV

Activities

Controller

LT

PV

SP

Load

Automatic Feedback Control

Fundamentals of Control
2006 PAControl.com

30

www.PAControl.com

Controller Algorithms and Tuning

Why Controllers Need Tuning?

Controllers are tuned in an effort to match the characteristics of the control equipment to the process so that two goals are achieved: is the foundation of process control measurement in that electricity: The system responds quickly to errors. The system remains stable (PV does not oscillate around the SP).

3. The change in the controller output divided by the change in the input to the controller is known as __________ .

Activities

GAIN
Controller tuning is performed to adjust the manner in which a control valve (or other final control element) responds to a change in error. In particular, we are interested in adjusting the gain of the controller such that a change in controller input will result in a change in controller output that will, in turn, cause sufficient change in valve position to eliminate error, but not so great a change as to cause instability or cycling. Gain is defined simply as the change in output divided by the change in input. Examples: Change in Input to Controller - 10% Change in Controller Output - 20% Gain = 20% / 10% = 2 Change in Input to Controller - 10% Change in Controller Output - 5% Gain = 5% / 10% = 0.5 convey measurements and instructions to other instruments in a control loop to maintain the highest level of safety and efficiency. The next three sections in this module discuss electricity, circuits, transmitters, and signals in greater detail so you can understand the importance of electricity in process control.

31

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Why Controllers Need Tuning?

Gain Plot - The Figure below is simply another graphical way of representing the concept of gain. Gain Kc = Output % / Input %
100 Gain=2 Gain=1

Activities
4. Fast or slow processes have no impact on controller gain settings. Is this statement true or false?

Output %
50 Gain=0.5

0 0 50 100

Input % Graphical Representaion of Gain Concept

Examples - The following examples help to illustrate the purpose of setting the controller gain to different values.
LIC I/P LIC I/P

LT

LT

Controllers May be Tuned to Help Match the Valve to the Process

Fast Process May Require Less Gain To Achieve Stability

Small volume liquid process

Slow Process May Require Higher Gain To Achieve Responsiveness

Large volume gas process

Fast and Slow Processes May Require Different Controller Gain Settings
32 Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Proportional Mode
PROPORTIONAL ACTION
The proportional mode is used to set the basic gain value of the controller. The setting for the proportional mode may be expressed as either: 1. Proportional Gain 2. Proportional Band

Activities
5. Identify the major disadvantage of proportional action.

1 2 3 4

PROPORTIONAL GAIN In electronic controllers, proportional action is typically expressed as proportional gain. Proportional Gain (Kc) answers the question: "What is the percentage change of the controller output relative to the percentage change in controller input?" Proportional Gain is expressed as: Gain, (Kc) = Output% /Input % PROPORTIONAL BAND
Proportional Band (PB) is another way of representing the same information and answers this question: "What percentage of change of the controller input span will cause a 100% change in controller output?" PB = Input (% Span) For 100%Output

Tends to leave an offset Reset Windup during shutdown Possible overshoot during startup Can cause cycling in fast process by amplifying noisy signals

Converting Between PB and Gain A simple equation converts gain to proportional Band: added. PB = 100/Gain Also recall that: Gain = 100%/PB

Proportional Gain, (Kc) = Output% / Input %

PB= Input(%Span) For 100%Output

33

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Proportional Mode
Gain=2 100 PB= 50% Gain=1 PB=100% Gain=0.5 PB=200%

Activities
6. If proportional gain is 0.5, and a level reading is 5% above setpoint, a proportional controller will signal the outflow control valve to open by <1 / 2.5 / 5> % of its full range.

Output %
50

50

100

150

200

Input % Relationship of Proportional Gain and Proportional Band

LIMITS OF PROPORTIONAL ACTION

Responds Only to a Change in error - Proportional action responds only to a change in the magnitude of the error. Does Not Return the PV to Setpoint - Proportional action will not return the PV to setpoint. It will, however, return the PV to a value that is within a defined span (PB) around the PV.

DETERMINING THE CONTROLLER OUTPUT

Controller Output - In a proportional only controller, the output is a function of the change in error and controller gain. Output Change, % = (Error Change, %) (Gain) Example: If the setpoint is suddenly changed 10% with a proportional band setting of 50%, the output will change as follows:

Calculating Controller Output Controller Output = Input, % X Gain Gain = 100%/PB EXAMPLE Input = 10% PB = 50%, so Gain = 100%/50% = 2

34

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Proportional Mode
Controller Output = Input X Gain Controller Output = 10% X 2 = 20% Expressed in Units: Controller Output Change = (0.2)(12 psi span) = 2.4 psi OR (0.2)(16 mA span) = 3.2 mA

Activities

PROPORTIONAL ACTION - CLOSED LOOP

Loop Gain - Every loop has a critical or natural frequency. This is the frequency at which cycling may exist. This critical frequency is determined by all of the loop components. If the loop gain is too high at this frequency, the PV will cycle around the SP; i.e., the process will become unstable. Low Gain Example - In the example below, the proportional band is high (gain is low). The loop is very stable, but an error remains between SP and PV.
10 9 8 7 % 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 PB= 200% Time IVP PV SP

Proportional Control Closed Loop - Low Gain Example

High Gain Example - In the example, the proportional band is small resulting in high gain, which is causing instability. Notice that the process variable is still not on set point.

35

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Proportional Mode
10 9 8 7 SP 6 %5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 PB=10% TIME PV IVP

Activities
7. What will be the result if the proportional gain is set too high? Select all options that apply.
1 2 3 4

Large offset Minimized offset Possible cycling Stable loop

Proportional Control Closed Loop - High Gain example

Proportional Summary - For the proportional mode, controller output is a function of a change in error. Proportional band is expressed in terms of the percentage change in error that will cause 100% change in controller output. Proportional gain is expressed as the percentage change in output divided by the percentage change in input. PB = (Input, % / Output, % ) x 100 = 100/Gain

Gain= Input % / Output %

Controller Output = (Change in Error)(Gain) 1. Proportional Mode Responds only to a change in error 2. Proportional mode alone will not return the PV to SP. Advantages - Simple Disadvantages - Error Settings - PB settings have the following effects:

Small PB (%) High Gain (%) Large PB (%) Low Gain

Minimize Offset Possible cycling Large Offset Stable Loop

Tuning - reduce PB (increase gain) until the process cycles following a disturbance, then double the PB (reduce gain by 50%).

36

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Integral Mode
INTEGRAL ACTION
Duration of Error and Integral Mode - Another component of error is the duration of the error, i.e., how long has the error existed? The controller output from the integral or reset mode is a function of the duration of the error.
100 90 80 70 60 % 50 40 30 20 10 0 0 1 2 3 4 5 6 7 8 9 10 SP Duration PV

Activities
8. _____________ action is the type of control algorithm that eliminates offset.

INTEGRAL(RESET)

OPEN LOOP ANALYSIS

Purpose- The purpose of integral action is to return the PV to SP. This is accomplished by repeating the action of the proportional mode as long as an error exists. With the exception of some electronic controllers, the integral or reset mode is always used with the proportional mode. Setting - Integral, or reset action, may be expressed in terms of: Repeats Per Minute - How many times the proportional action is repeated each minute. Minutes Per Repeat - How many minutes are required for 1 repeat to occur.

37

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Integral Mode
CLOSED LOOP ANALYSIS

Activities

Closed Loop With Reset - Adding reset to the controller adds one more 9. Which of the following are integral or reset actions expressed in gain component to the loop. The faster the reset action, the greater terms of? the gain. Select all options that apply. Slow Reset Example - In this example the loop is stable because the total loop gain is not too high at the loop critical frequency. 1 Repeats per setting Notice thatthe process variable does reach set point due to the reset 2 Repeats per minute action. 3 Repeats per loop 100 4 Minutes per repeat 90
80 70 60 % 40 50 PV SP

30 20 10 0 PB=80% Repeat=2.0 Repeats/min TIME 0 1 2 3 4 5 6 7 8 9 10 IVP

SLOW RESET, CLOSED LOOP

Fast Reset Example - In the example the rest is too fast and the PV is cycling around the SP.

100 90 80 70 60 50 % 40 30 20 10 0 0 1 2 3 4 5 6 7 8 9 IVP PB=80% Repeat=10 Repeats/min TIME 10 PV SP

FAST RESET, CLOSED LOOP

38

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Integral Mode
RESET WINDUP
Defined - Reset windup is described as a situation where the controller output is driven from a desired output level because of a large difference between the set point and the process variable.
100

Activities
10. Identify the major disadvantages of integral action. Select all options that apply.
1 2 3 4

Output% IVP ARW

Tends to leave an offset Reset windup during shutdown Possible overshoot during start up Can cause cycling in fast process by amplifying noisy signals

0 INPUT(ERROR)

Reset Windup - Ant-Reset Windup

Shutdown - Reset windup is common on shut down because the process variable may go to zero but the set point has not changed, therefore this large error will drive the output to one extreme.
100

SP Input %

PV ARW

0 Shutdown Input(Error) Startup

Reset Windup - Shutdown and Startup

Startup - At start up, large process variable overshoot may occur because the reset speed prevents the output from reaching its desired value fast enough. Anti Reset Windup - Controllers can be modified with an anti-reset

39

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Integral Mode
windup (ARW) device. The purpose of an anti-reset option is to allow the output to reach its desired value quicker, therefore minimizing the overshoot.

Activities

SUMMARY
Integral (Reset) Summary - Output is a repeat of the proportional action as long as error exists. The units are in terms of repeats per minute or minutes per repeat. Advantages - Eliminates error Disadvantages - Reset windup and possible overshoot
Fast Reset 1.High Gain (Large Repeats/Min.,Small Min./Repeat) 2.Fast Return To Setpoint 3.Possible Cycling Slow Reset 1.Low Gain (Small Repeats/Min.,Large Min./Repeats) 2.Slow Return To Setpoint 3.Stable Loop Trailing and Error Tuning - Increase repeats per minute until the PV cycles following a disturbance, then slow the reset action to a value that is 1/3 of the initial setting.

40

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Derivative Mode
DERIVATIVE ACTION
Derivative Mode Basics - Some large and/or slow process do not respond well to small changes in controller output. For example, a large liquid level process or a large thermal process (a heat exchanger) may react very slowly to a small change in controller output. To improve response, a large initial change in controller output may be applied. This action is the role of the derivative mode.

Activities
11. ___________ action is a control algorithm that is tied to the rate of change in the error.

The derivative action is initiated whenever there is a change in the rate of change of the error (the slope of the PV). The magnitude of the derivative action is determined by the setting of the derivative . The mode of a PID controller and the rate of change of the PV. The Derivative setting is expressed in terms of minutes. In oper ation, the the controller first compares the current PV with the last value of the PV. If there is a change in the slope of the PV, the controller 12. Which of the following are derivative or etermines what its output would be at a future point in time rate actions expressed in terms of? (the future point in time is determined by the value of the derivative setting, in minutes). The derivative mode immediately increases the output by that amount. 1 Repeats per minute 100 Hours 2 90 Seconds 3 80 Slope= Rate of Error Change(Y/X) Minutes 4 70 5 Milliseconds 60
50 % 40 30 20 10 0 0 1 2 3 4 5 6 7 8 9 10 TIME Y X PV

SP

Derivative Action is based on the rate of change in Error (Y/X)

41

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Derivative Mode
Example - Let's start a closed loop example by looking at a temperature control system. IN this example, the time scale has been lengthened to help illustrate controller actions in a slow process. Assume a proportional band settingof 50%. There is no reset at this time. The proportional gain of 2 acting on a 10% change in set pint results in a change in controller output of 20%. Because temperature is a slow process the setting time after a change in error is quite long. And, in this example, the PV never becomes equal to the SP because there is no reset. Rate Effect - To illustrate the effect of rate action, we will add the are mode with a setting of 1 minute. Notice the very large controller output at time 0. The output spike is the result of rate action. Recall that the change in output due to rate action is a function of the speed (rate) of change of error, which in a step is nearly infinite. The addition of rate alone will not cause the process variable to match the set point.
100 90 80 70 60 50 40 30 20 10 0 0 100 200 300 400 PB=50% Reset=0 Rate=0 TIME PV SP IVP

Activities
13. The addition of derivative or rate alone to a close loop control can cause the process variable to match the set point. Is this statement true or false?

100 IVP 90 80 70 PV 60 50 40 30 20 10 0 0 100 200 300 400 PB=50% Reset=0 Rate=1 min TIME PV SP

No Rate, Small Rate examples, Closed Loop

42 Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Derivative Mode
Effect of Fast Rate - Let's now increase the rate setting to 10 minutes. The controller gain is now much higher. As a result, both the IVP (controller output) and the PV are cycling. The point here is that increasing the rate setting will not cause the PV to settle at the SP.
100 90 80 70 60 50 40 30 20 10 0 PB= 50% Reset=0 Rate= 10 min 0 100 200 300 400 PV SP IVP

Activities

TIME

P+D, High Rate Setting, Closed Loop Analysis

Need for Reset Action - It is now clear that reset must be added to bring process variable back to set point. Applications - Because this component of the controller output is dependent on the speed of change of the input or error, the output will be very erratic if rate is used on fast process or one with noisy signals. The controller output, as a result of rate, will have the greatest change when the input changes rapidly. Controller Option to Ignore Change in SP - Many controllers, especially digital types, are designed to respond to changes in the PV only, and to ignore changes in SP. This feature eliminates a major upset upset that would occur following a change in the setpoint.

43

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Derivative Mode
SUMMARY Derivative (Rate) Sumary - Rate action is a function of the speed of change of the error. The units are minutes. The action is to apply an immediate response that is equal to the proportional plus reset action that would have occurred some number of minutes I the future.
Advantages - Rapid output reduces the time that is required to return PV to SP in slow process.
Disadvantage - Dramatically amplifies noisy signals; can cause cycling in fast processes. Settings Large (Minutes) 1.High Gain 2.Large Output Change 3.Possible Cycling 1.Low Gain 2.Small Output Change 3.Stable Loop

Activities

Small (Minutes)

Trial-and-Error Tuning

Increase the rate setting until the process cycles following a disturbance, then reduce the rate setting to one-third of the initial value.

44

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Controller Algorithms and Tuning

Controller Algorithms
Proportional, PI, and PID Control
By using all three control algorithms together, process operators can: Achieve rapid response to major disturbances with derivative control Hold the process near setpoint without major fluctuations with proportional control Eliminate offset with integral control Not every process requires a full PID control strategy. If a small offset has no impact on the process, then proportional control alone may be sufficient. PI control is used where no offset can be tolerated, where noise (temporary error readings that do not reflect the true process variable condition) may be present, and where excessive dead time (time after a disturbance before control action takes place) is not a problem. In processes where no offset can be tolerated, no noise is present, and where dead time is an issue, customers can use full PID control. Table 7.2 shows common types of control loops and which types of control algorithms are typically used.
Controlled Variable

Activities
14. What type of control is used in an application where noise is present, but where no offset can be tolerated?

1 2 3 4

P only PD PI PID

Proportional Control

PI Control

PID Control

Flow

Yes

Yes

No

Level

Yes

Yes

Rare

Temperature

Yes

Yes

Yes

Pressure

Yes

Yes

Rare

Analytical

Yes

Yes

Rare

Table 7.2: Control Loops and Control Algorithms

COMPLETE WORKBOOK EXERCISE - CONTROLLER ALGORITHMS AND TUNING

Fundamentals of Control
2006 PAControl.com

45

www.PAControl.com

Process Control Loops

In this section, you will learn about how control components and control algorithms are integrated to create a process control system. Because in some processes many variables must be controlled, and each variable can have an impact on the entire system, control systems must be designed to respond to disturbances at any point in the system and to mitigate the effect of those disturbances throughout the system.

LEARNING OBJECTIVES
After completing this section, you will be able to: Explain how a multivariable loop is different from a single loop. Differentiate feedback and feedforward control loops in terms of their operation, design, benefits, and limitations Perform the following functions for each type of standard process control loop (i.e., pressure, flow, level, and temperature): State the type of control typically used and explain why it is used Identify and describe considerations for equipment selection (e.g., speed, noise) Identify typical equipment requirements Diagram the loop using ISA symbology Explain the basic implementation process, including a description of equipment requirements and considerations, for each of the following types of control: Cascade control Batch control Ratio control Selective control Fuzzy control Describe benefits and limitations of each type of control listed above Give examples of process applications in which each type of control described in this section might be used

Note: To answer the activity questions the Hand Tool (H) should be activated.

Fundamentals of Control
2006 PAControl.com

46

www.PAControl.com

Process Control Loops

Single Control Loops

Control loops can be divided into two categories: Single variable loops and multi-variable loops.

Activities
1. What type of control loop takes action in response to measured deviation from setpoint?

FEEDBACK CONTROL
A feedback loop measures a process variable and sends the measurement to a controller for comparison to setpoint. If the process variable is not at setpoint, control action is taken to return the process variable to setpoint. Figure 7.18 illustrates a feedback loop in which a transmitter measures the temperature of a fluid and, if necessary, opens or closes a hot steam valve to adjust the fluids temperature.

1 2 3 4

Discrete control loop Multi-step control loop Open loop Feedback control loop

Controller Process fluid

Steam valve

Transmitter

Feedback Loop

An everyday example of a feedback loop is the cruise control system in an automobile. A setpoint is established for speed. When the car begins to climb a hill, the speed drops below setpoint and the controller adjusts the throttle to return the cars speed to setpoint. Feedback loops are commonly used in the process control industry. The advantage of a feedback loop is that it directly controls the desired process variable. The disadvantage to feedback loops is that the process variable must leave setpoint for action to be taken.

47

Fundamentals of Control
2006 PAControl.com.

www.PAControl.com

Process Control Loops

Examples of Single Control Loops While each application has its own characteristics, some general Activities statements can be made about pressure, flow, level, and temperature
loops.

PRESSURE CONTROL LOOPS

Pressure control loops vary in speedthat is, they can respond to changes in load or to control action slowly or quickly. The speed required in a pressure control loop may be dictated by the volume of the process fluid. High-volume systems (e.g., large natural gas storage facilities) tend to change more slowly than low-volume systems (Figure 7.21).
Pneumatic controller

2. How does a high-volume pressure control loop react as compared to a small-volume pressure control loop?

1 2 3 4

Same rate Quicker Slower Extremely fast

Relief valve
Pressure transmitter

Process fluid Fluid pump

A Pressure Loop

Fundamentals of Control
2006 PAControl.com

48

www.PAControl.com

Process Control Loops

Examples of Single Control Loops FLOW CONTROL LOOPS Activities

Generally, flow control loops are regarded as fast loops that respond to changes quickly. Therefore, flow control equipment must have fast sampling and response times. Because flow transmitters tend to be rather sensitive devices, they can produce rapid fluctuations or noise in the control signal. To compensate for noise, many flow transmitters have a damping function that filters out noise. Sometimes, filters are added between the transmitter and the control system. Because the temperature of the process fluid affects its density, temperature measurements are often taken with flow measurements and compensation for temperature is accounted for in the flow calculation. Typically, a flow sensor, a transmitter, a controller, and a valve or pump are used in flow control loops (Figure 7.22).
Pneumatic controller

3. Flow control loops are generally considered to be slow responding loops. Is this statement true or false?

Flow transmitter Valve

Process fluid Fluid pump

A Flow Loop

49

Fundamentals of Control
2006 PAControl.com.

www.PAControl.com

Process Control Loops

Examples of Single Control Loops Activities LEVEL CONTROL LOOPS

The speed of changes in a level control loop largely depends on the size and shape of the process vessel (e.g., larger vessels take longer to fill than smaller ones) and the flow rate of the input and outflow pipes. Manufacturers may use one of many different measurement technologies to determine level, including radar, ultrasonic, float gauge, and pressure measurement. The final control element in a level control loop is usually a valve on the input and/or outflow connections to the tank (Figure 7.23). Because it is often critical to avoid tank overflow, redundant level control systems are sometimes employed.
Converter Level controller

4. Redundant control systems are sometimes used in level applications because preventing tank overflow is often critically important. Is this statement true or false?

Differential pressure transmitter

A Level Loop

Fundamentals of Control
2006 PAControl.com

50

www.PAControl.com

Process Control Loops

Examples of Single Control Loops TEMPERATURE CONTROL LOOPS Activities

Because of the time required to change the temperature of a process fluid, temperature loops tend to be relatively slow. Feedforward control strategies are often used to increase the speed of the temperature loop response. RTDs or thermocouples are typical temperature sensors. Temperature transmitters and controllers are used, although it is not uncommon to see temperature sensors wired directly to the input interface of a controller. The final control element for a temperature loop is usually the fuel valve to a burner or a valve to some kind of heat exchanger. Sometimes, cool process fluid is added to the mix to maintain temperature (Figure 7.24).
Controller

5. What type of control strategy is often used to increase the speed of a temperature control loop?

1 2 3 4

Feedforward control Feedback control Cascade control Ratio control

Process fluid Valve

Temperature transmitter

A Temperature Loop

51

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops MULTIVARIABLE LOOPS Activities

Multivariable loops are control loops in which a primary controller controls one process variable by sending signals to a controller of a different loop that impacts the process variable of the primary loop. For example, the primary process variable may be the temperature of the fluid in a tank that is heated by a steam jacket (a pressurized steam chamber surrounding the tank). To control the primary variable (temperature), the primary (master) controller signals the secondary (slave) controller that is controlling steam pressure. The primary controller will manipulate the setpoint of the secondary controller to maintain the setpoint temperature of the primary process variable (Figure 7.17).
.

6. A multivariable control loop contains a primary and secondary controller assigned to different process variables? Is this statement true or false?

Primary controller Transmitter

SP
Transmitter

Secondary controller

Valve

Multivariable Loop

When tuning a control loop, it is important to take into account the presence of multivariable loops. The standard procedure is to tune the secondary loop before tuning the primary loop because adjustments to the secondary loop impact the primary loop. Tuning the primary loop will not impact the secondary loop tuning.

52

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops Activities FEEDFORWARD CONTROL

Feedforward control is a control system that anticipates load disturbances and controls them before they can impact the process variable. For feedforward control to work, the user must have a mathematical understanding of how the manipulated variables will impact the process variable. Figure 7.19 shows a feedforward loop in which a flow transmitter opens or closes a hot steam valve based on how much cold fluid passes through the flow sensor.
Flow transmitter

7. What type of control loop anticipates and controls load disturbances before they can impact the process variable?

1 2 3 4

Controller

Feedback control loop Feedforward control loop Ratio control loop Single variable loop

Cold process fluid

Steam valve

Feedforward Control

An advantage of feedforward control is that error is prevented, rather than corrected. However, it is difficult to account for all possible load disturbances in a system through feedforward control. Factors such as outside temperature, buildup in pipes, consistency of raw materials, humidity, and moisture content can all become load disturbances and cannot always be effectively accounted for in a feedforward system. In general, feedforward systems should be used in cases where the controlled variable has the potential of being a major load disturbance on the process variable ultimately being controlled. The added complexity and expense of feedforward control may not be equal to the benefits of increased control in the case of a variable that causes only a small load disturbance.

Fundamentals of Control
2006 PAControl.com

53

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops FEEDFORWARD PLUS FEEDBACK Activities

Because of the difficulty of accounting for every possible load disturbance in a feedforward system, feedforward systems are often combined with feedback systems. Controllers with summing functions are used in these combined systems to total the input from both the feedforward loop and the feedback loop, and send a unified signal to the final control element. Figure 7.20 shows a feedforward-plus-feedback loop in which both a flow transmitter and a temperature transmitter provide information for controlling a hot steam valve.
Feedforward controller

8. A controller with a summing function totals the input from both the feedforward loop and the feedback loop and sends a unified signal to the final control element. This is how a single control signal is sent to the final control element in a feedforward plus feedback system. Is this statement true or false?

Summing controller

Feedback controller

Flow transmitter

Process fluid Steam valve

Temperature transmitter

Feedforward Plus Feedback Control System

54

Fundamentals of Control
2006 PAControl.com.

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops This module has discussed specific types of control loops, what Activities components are used in them, and some of the applications (e.g., flow,
pressure, temperature) they are applied to. In practice, however, many independent and interconnected loops are combined to control the workings of a typical plant. This section will acquaint you with some of the methods of control currently being used in process industries.

9. Ratio control is the term used to describe a system in which the controller of the primary loop determines the setpoint of a secondary loop. Is this statement true or false?

CASCADE CONTROL
Cascade control is a control system in which a secondary (slave) control loop is set up to control a variable that is a major source of load disturbance for another primary (master) control loop. The controller of the primary loop determines the setpoint of the summing contoller in the secondary loop (Figure 7.25).

Secondary controller

Primary controller

Process fluid Temperature transmitter

Flow transmitter

Valve

Cascade Control

Fundamentals of Control
2006 PAControl.com

55

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops BATCH CONTROL Activities

Batch processes are those processes that are taken from start to finish in batches. For example, mixing the ingredients for a juice drinks is often a batch process. Typically, a limited amount of one flavor (e.g., orange drink or apple drink) is mixed at a time. For these reasons, it is not practical to have a continuous process running. Batch processes often involve getting the correct proportion of ingredients into the batch. Level, flow, pressure, temperature, and often mass measurements are used at various stages of batch processes. A disadvantage of batch control is that the process must be frequently restarted. Start-up presents control problems because, typically, all measurements in the system are below setpoint at start-up. Another disadvantage is that as recipes change, control instruments may need to be recalibrated.

10. Which term describes a control system in which controlled flow is added proportionately to an uncontrolled flow?

1 2 3 4

Selective control Cascade control Ratio control Fuzzy control

RATIO CONTROL
Imagine a process in which an acid must be diluted with water in the proportion two parts water to one part acid. If a tank has an acid supply on one side of a mixing vessel and a water supply on the other, a control system could be developed to control the ratio of acid to water, even though the water supply itself may not be controlled. This type of control system is called ratio control (Figure 7.26). Ratio control is used in many applications and involves a contoller that receives input from a flow measurement device on the unregulated (wild) flow. The controller performs a ratio calculation and signals the appropriate setpoint to another controller that sets the flow of the second fluid so that the proper proportion of the second fluid can be added. Ratio control might be used where a continuous process is going on and an additive is being put into the flow (e.g., chlorination of water).

Water flow

Acid flow

Ratio Control

56

Fundamentals of Control
2006 PAControl.com

www.PAControl.com

Process Control Loops

Multi-Variable / Advanced Control Loops Activities SELECTIVE CONTROL

Selective control refers to a control system in which the more important of two variables will be maintained. For example, in a boiler control system, if fuel flow outpaces air flow, then uncombusted fuel can build up in the boiler and cause an explosion. Selective control is used to allow for an air-rich mixture, but never a fuel-rich mixture. Selective control is most often used when equipment must be protected or safety maintained, even at the cost of not maintaining an optimal process variable setpoint. 11. In which type of control system will the more important of two variables be maintained?

1 2 3 4

FUZZY CONTROL
Fuzzy control is a form of adaptive control in which the controller uses fuzzy logic to make decisions about adjusting the process. Fuzzy logic is a form of computer logic where whether something is or is not included in a set is based on a grading scale in which multiple factors are accounted for and rated by the computer. The essential idea of fuzzy control is to create a kind of artificial intelligence that will account for numerous variables, formulate a theory of how to make improvements, adjust the process, and learn from the result. Fuzzy control is a relatively new technology. Because a machine makes process control changes without consulting humans, fuzzy control removes from operators some of the ability, but none of the responsibility, to control a process.

Fuzzy control Cascade control Ratio control Selective control

12.

___________ control is the term used to describe a control system in which the controller uses computer logic to make decisions about adjusting the process.

COMPLETE WORKBOOK EXERCISE - PROCESS CONTROL LOOPS

Fundamentals of Control
2006 PAControl.com

57

www.PAControl.com

Module 7: Workbook Exercises

EXERCISE 7.1 THE IMPORTANCE OF PROCESS CONTROL
1. Which of the following options best represents the reasons to control a process? (Select three options that apply) (1) (2) (3) (4) (5) Reduce variability Increase productivity Increase efficiency Reduce cost Ensure safety

2.

Process is defined as the method of changing or refining raw materials to create end products. Is this statement true or false? (1) (2) True False

3.

Which of the following are advantages of reducing variability in a process application? (1) (2) (3) (4) Helps ensure a consistently high-quality end product. Helps ensure an increase in the reaction rate of the process. Helps ensure increase in efficiency of the process. Helps ensure safety

Page 58

Workbook Exercises
2006 PAControl.com

www.PAControl.com

Module 7: Workbook Exercises

EXERCISE 7.2 CONTROL THEORY BASICS
1. Which of the following tasks is associated with process control? (Select three options that apply) (1) (2) (3) (4) (5) Measurement Comparison Quality Analysis Adjustment Calculation

2.

Which of the following variables are commonly measured or monitored in process control applications? (Select three options that apply) (1) (2) (3) (4) (5) Pressure Viscosity Nitrogen content Flow rate Temperature

3.

A process liquid level needs to be held within 5 ft of 150 ft in a large tank. A pressure transmitter monitors the liquids level using a pressure reading and sends the result to a controller. The controller compares the level reading to the set point and opens or closes an inflow or outflow pipe depending on the liquid level. Keeping in mind the given scenario, match the terms in Column A with their values in Column B. (1) (2) (3) (4) Inferred process variable Manipulated variable Measured variable Set point (A) (B) (C) (D) 150 ft Pressure Flow of liquid to the tank Level

Workbook Exercises
2006 PAControl.com

Page 59

www.PAControl.com

Module 7: Workbook Exercises

4. Match each term to its correct definition. (1) (2) (3) (4) (5) (A) (B) (C) (D) (E) Load disturbance Control algorithm Manual control Manipulated variable Set point The factor that is changed to keep a measured variable at set point. An undesired change in a factor that can affect the process variable. A value or range of values for a process variable that must be maintained to keep the process running properly. A control operation that directly involves human action. A mathematical expression of a control function

5.

Match each term to its correct description. (1) (2) (3) (A) (B) (C) Closed-loop, automatic control Closed-loop, manual control Open-loop, automatic control _____ _____ _____

An operator turns off the heater coil when the temperature transmitter outputs a certain reading. A controller turns off the heater coil at set intervals, regardless of the process temperature. A temperature sensor measures process temperature, sends the result to a controller to compare to the setpoint, and the controller turns off the heater coil.

6.

__________ is a deviation from set point due to load disturbance. (1) (2) (3) Error Offset Rate of change

7.

__________ is a continuing error due to the inability of a control system to keep the measured variable at set point. (1) (2) (3) Load disturbance Offset Pressure

Page 60

Workbook Exercises
2006 PAControl.com

www.PAControl.com

Module 7: Workbook Exercises

EXERCISE 7.3 COMPONENTS OF CONTROL LOOPS AND ISA SYMBOLOGY
1. The basic function of a __________ is to convert a reading from a transducer into a standard signal and transmit that signal to a controller or computer monitor. (1) (2) (3) recorder transmitter converter

2.

420 mA is the most common standard analog signal used in the process control industry today. Is this statement true or false? (1) (2) True False

3.

Match the signal type in Column A with its example/application in Column B. (1) (2) (3) Analog signal Pneumatic signal Digital signal (A) (B) (C) 3 15 psig Fieldbus, Profibus and Modbus 4-20 mA and 1 5 V

4.

A customer would use __________to read the temperature of a process fluid on a display. (1) (2) (3) an indicator a volt-meter an actuator

5.

Match each control loop equipment to its correct description. (1) (2) (3) (4) Recorder Controller Final control element Actuator _____ _____ _____ _____

6.

A pump motor is the most commonly used final control element. Is this statement true or false? (1) (2) True False

Workbook Exercises
2006 PAControl.com

Page 61

www.PAControl.com

Module 7: Workbook Exercises

7. Match the ISA symbols in Column A with its respective description in Column B. (1) (A) Programmable logic control

(2)

(B)

Temperature transmitter

(3)

(C)

Pneumatically actuated valve

(4)

(D)

Electrically actuated valve

Page 62

Workbook Exercises
2006 PAControl.com

www.PAControl.com

Module 7: Workbook Exercises

EXERCISE 7.4 CONTROL ALGORITHMS AND TUNING
1. Match each term to its correct definitions. (1) (2) (3) (4) (5) (A) (B) (C) (D) (E) Proportional band Proportional/integral (PI) control Proportional control Derivative control Integral control A type of control that corrects error and eliminates offset. A type of control that produce erratic output in noisy applications. The percent change in error that will cause a 100% change in controller output. A type of control that is prone to leaving an offset. A type of control that repeats the action of the proportional mode as long as an error exists.

2.

Identify the two effects on a process variable if the proportional gain (Pgain) is set too high? (Select all that apply)

(1) (2) (3) (4)

Minimize offset Large offset Stable loop Possible cycling

3.

Derivative gain (Dgain) is typically set to zero in flow applications since flow applications are usually noisy and derivative control will react to readings that are in fact noise, thus preventing the process from holding set point. Is this statement true or false? (1) (2) True False

Workbook Exercises
2006 PAControl.com

Page 63

www.PAControl.com

Module 7: Workbook Exercises

EXERCISE 7.5 PROCESS CONTROL LOOPS
1. Which control system anticipates load disturbances and controls them before they can impact the process variable? (1) (2) (3) (4) Selective control Fuzzy control Feed forward control Cascade control

2.

Match the component label in Column A to its ISA symbol representation in Column B. (1) Flow transmitter (A)

(2)

Temperature transmitter

(B)

(3)

Flow controller

(C)

(4)

Valve

(D)

3.

If R1 = 60 , R2 = 100 the circuit? (1) (2) (3) slow fast variable speed

, and R3 = 100

, what is the equivalent resistance (Req) in

Page 64

Workbook Exercises
2006 PAControl.com.

www.PAControl.com

Module 7: Workbook Exercises - Answers

Exercise 7.1 The Importance of Process Control

1. 2. 3.

1, 3, 5 1 1

Exercise 7.2 Control Theory Basics

1. 2. 3. 4. 5. 6. 7.

1, 2, 4 1, 4, 5 D, C, B, A B, E, D, A, C C, A, B 1 2

Exercise 7.3 Components of Control Loops and ISA Symbology

1. 2. 3. 4. 5. 6. 7.

2 1 C, A, B 1 C, D, B, A 2 B, C, D, A

Exercise 7.4 Control Algorithms and Tuning

1. 2. 3.

C, A, D, B, E 1, 4 1

Exercise 7.5 Process Control Loops

1. 2. 3.

3 B, C, D, A 1

Workbook Exercises
2006 PAControl.com

Page 65

www.PAControl.com

Module 7: Activity Answers

The Importance of Process Control

1. 2. 3.

True 1,3,5 1,2,4

Control Theory Basics

1. 2. 3. 4. 5. 6. 7. 8.

True True True 4 3 False False 2,4

Components of Control Loops and ISA Symbology

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.

1,2,5 False 3 True 2,3,4 1 1,4 2 4 3 1 2 1 2 3 True 4 True True 1 3

Page 66

Activity Answers
2006 PAControl.com

www.PAControl.com

Module 7: Activity Answers

Controller Algorithms and Tuning

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.

1,2,3,4 False 2 False 1 2.5 2,3 3 2,4 2,3 2 4 False 3

Process Control Loops

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.

4 3 False True 1 True 2 True False 3 4 1

Activity Answers
2006 PAControl.com

Page 67

www.PAControl.com

www.PAControl.com