SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017

& ANSI/NCSL Z540-1-1994 & ANSI/NCSL Z540.3-2006

SIMCO ELECTRONICS
783 N. Grove Road, Suite 106
Richardson, TX 75081
Erwin Kanins Phone: 972 994 0120

CALIBRATION

Valid To: September 30, 2023 Certificate Number: 1395.03

In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this
laboratory to perform the following calibrations1, 6:

I. Dimensional

Parameter/Equipment Range CMC2, 4 (±) Comments

Micrometers3 Up to 1 in (30 + 2L) μin Gage blocks, optical flat

(Outside, Inside, (1 to 16) in (20 + 15L) μin
Depth)

Micrometer End Up to 12 in (5.9 + 3.7L) µin Pratt & Whitney

Standards LabMaster™ Universal
and gage blocks

Height Gages3 Up to 1 in 76 μin Gage blocks,

(1 to 36) in (77 + 14L) μin surface plate

Calipers3 Up to 36 in (290 + 10L) μin Gage blocks

Linear Indicators – Up to 10 in:

Digital and Analog (20 μin resolution) (8.1 + 5L) μin Pratt & Whitney
(50 μin resolution) (13 + 5L) μin LabMaster™ Universal
(100 μin resolution) (28 + 5L) μin and gage blocks
(0.001 in resolution) (150 + 5L) μin

(A2LA Cert. No. 1395.03) 7/26/2021 Page 1 of 20

 Parameter/Equipment Range CMC2, 4 (±) Comments

Cylindrical Plug Up to 1 in 10 µin Pratt & Whitney

Gages & Master Discs (1 to 12) in (4.8 + 5L) µin LabMaster™ Universal
and gage blocks

Cylindrical Ring (0.040 to 1.0) in 10 µin Pratt & Whitney

Gages (> 1.0 to 14) in (8.8 + 3.3L) µin LabMaster™ Universal
and gage blocks

Thread Plugs –

UN (60° threads) Pitch Diameter:

Up to 12 in, (70 + 5L) µin Pratt & Whitney
Pitch: (4 to 80) TPI LabMaster™ Universal,
gage blocks and thread
Pitch Diameter: wires
(1 to 300) mm, (1.7 + 0.13L) µm
Pitch: (0.3 to 4) mm

UN Major Diameter:
Up to 1 in 10 µin Pratt & Whitney
(1 to 12) in (4.8 + 5L) µin LabMaster™ Universal
and gage blocks

Steel Rulers and Tape Up to 40 in 0.0014 in + 43L µin Linear scale calibrator
Measures

Wafer Film Thickness (3.0 to 1500) nm 0.65 nm Woolam VASE System

Standards w/ NIST SRMs:
NIST 2534
NIST 2531
NIST 2532

Precision Step Height (10 to 100) nm 2.5 % Veeco Dektak 3

Standards (>100 to 2500) nm 0.6 % comparator, Veeco 138 -
367, -369, -371 step
height standards

(A2LA Cert. No. 1395.03) 7/26/2021 Page 2 of 20

II. Electrical – DC/Low Frequency

Parameter/Equipment Range CMC2, 4, 5 (±) Comments

DC Voltage3 – Generate Up to 220 mV 8.1 µV/V + 0.4 µV Fluke calibrator 5720A

220 mV to 2.2 V 4.6 µV/V + 0.7 µV
(2.2 to 11) V 3.5 µV/V + 2.5 µV
(11 to 22) V 3.5 µV/V + 4 µV
(22 to 220) V 4.4 µV/V + 40 µV
(220 to 1100) V 5.2 µV/V + 400 µV

(1 to 75) kV 0.16 % ROSS probe

VD90-16.5Y-AK-K

Fixed Points 1V 2 μV/V Fluke Zener standard

1.018 V 4 μV/V 732A
10 V 1 μV/V

DC Voltage3 – Measure Up to 200 mV 6.4 µV/V + 0.1 µV Fluke DMM 8508A

200 mV to 2 V 4.1 µV/V + 0.4 µV
(2 to 20) V 4.4 µV/V + 4.0 µV
(20 to 200) V 5.9 µV/V + 40 µV
(200 to 1050) V 5.9 µV/V + 0.50 mV

(1 to 90) kV 0.16 % ROSS probe

VD90-16.5Y-AK-K

DC Current3 – Up to 220 µA 37 µA/A + 6 nA Fluke calibrator 5720A

Generate 220 µA to 2.2 mA 32 µA/A + 7 nA
(2.2 to 22) mA 35 µA/A + 40 nA
(22 to 220) mA 41 µA/A + 0.7 µA
220 mA to 2.2 A 64 µA/A + 12 µA

(2.2 to 11) A 0.034 % + 0.48 mA Fluke amplifier 5725A

(1 to 10) A 0.015 % Guildline 9211A shunt,

(10 to 100) A 0.052 % HP 6031A, Fluke DMM
8508A

DC Current – Clamp (10 to 16.5) A 0.40 % + 0.06 A Fluke 5500A/coil &

Meters3 (16.5 to 150) A 0.40 % + 0.06 A 5520A
(150 to 1000) A 0.40 % + 0.06 A

(A2LA Cert. No. 1395.03) 7/26/2021 Page 3 of 20

 Parameter/Equipment Range CMC2, 4, 5 (±) Comments

DC Current3 – Up to 200 µA 13 µA/A + 0.4 nA Fluke DMM 8508A

Measure 200 µA to 2 mA 13 µA/A + 4 nA
(2 to 20) mA 15 µA/A + 40 nA
(20 to 200) mA 50 µA/A + 0.8 µA
200 mA to 2 A 0.019 % + 16 µA
(2 to 20) A 0.042 % + 0.40 mA

(1 to 10) A 0.015 % Guildline 9211A shunt,

(10 to 20) A 0.054 % Fluke DMM 8508A
(20 to 100) A 0.052 %
(100 to 300) A 0.11 %

Resistance3 – Generate (0 to 11) Ω 36 μΩ/Ω + 0.78 mΩ Fluke 5522A

(11 to 33) Ω 27 μΩ/Ω + 1.2 mΩ
(33 to 110) Ω 25 μΩ/Ω + 1.1 mΩ
(110 to 330) Ω 25 μΩ/Ω + 1.6 mΩ
(0.33 to 1.1) kΩ 25 μΩ/Ω + 1.6 mΩ
(1.1 to 3.3) kΩ 26 μΩ/Ω + 16 mΩ
(3.3 to 11) kΩ 26 μΩ/Ω + 16 mΩ
(11 to 33) kΩ 26 μΩ/Ω + 0.16 Ω
(33 to 110) kΩ 26 μΩ/Ω + 0.16 Ω
(110 to 330) kΩ 28 μΩ/Ω + 1.6 Ω
(0.33 to 1.1) MΩ 28 μΩ/Ω + 1.6 Ω
(1.1 to 3.3) MΩ 50 μΩ/Ω + 24 Ω
(3.3 to 11) MΩ 0.011 % + 39 Ω
(11 to 33) MΩ 0.021 % + 2 kΩ
(33 to 110) MΩ 0.040 % + 2.4 kΩ
(110 to 330) MΩ 0.24 % + 78 kΩ
(0.33 to 1.1) GΩ 1.2 % + 0.39 MΩ

Fixed Points 1.0 Ω 4 µΩ/Ω L&N 4210

0Ω 52 µΩ Fluke calibrator 5720A

1Ω 84 µΩ/Ω
1.9 Ω 84 µΩ/Ω

10 Ω 24 µΩ/Ω

19 Ω 25 µΩ/Ω

(100, 190) Ω 11 µΩ/Ω

1 kΩ 8.6 µΩ/Ω
1.9 kΩ 8.0 µΩ/Ω

(10, 19) kΩ 8.0 µΩ/Ω

100 kΩ 10 µΩ/Ω

190 kΩ 10 µΩ/Ω

(A2LA Cert. No. 1395.03) 7/26/2021 Page 4 of 20

 Parameter/Equipment Range CMC2, 4, 5 (±) Comments

Resistance3 – Generate
(cont.)

Fixed Points 1 MΩ 16 µΩ/Ω Fluke calibrator 5720A

1.9 MΩ 17 µΩ/Ω
10 MΩ 34 µΩ/Ω
19 MΩ 42 µΩ/Ω
100 MΩ 0.011 %

Resistance3 – Measure Up to 2 Ω 20 µΩ/Ω + 4 µΩ Fluke DMM 8508A

(2 to 20) Ω 11 µΩ/Ω + 14 µΩ
(20 to 200) Ω 8.6 µΩ/Ω + 50 µΩ
200 Ω to 2 kΩ 8.6 µΩ/Ω + 500 µΩ
(2 to 20) kΩ 8.6 µΩ/Ω + 5 mΩ
(20 to 200) kΩ 8.9 µΩ/Ω + 50 mΩ
200 kΩ to 2 MΩ 11 µΩ/Ω + 1.0 Ω
(2 to 20) MΩ 24 µΩ/Ω + 0.10 kΩ
(20 to 200) MΩ 80 µΩ/Ω + 1 kΩ
200 MΩ to 2 GΩ 0.022 % + 100 kΩ
(2 to 100) GΩ 0.74 % Keithley 6517B

Electrical Simulation
of Thermocouples3 –

Type E (-250 to -100) °C 0.41 °C Fluke calibrator 5522A

(-100 to -25) °C 0.18 °C
(-25 to 350) °C 0.17 °C
(350 to 650) °C 0.18 °C
(650 to 1000) °C 0.21 °C

Type J (-210 to -100) °C 0.24 °C

(-100 to -30) °C 0.18 °C
(-30 to 150) °C 0.17 °C
(150 to 760) °C 0.18 °C
(760 to 1200) °C 0.22 °C

Type K (-200 to -100) °C 0.28 °C

(-100 to -25) °C 0.19 °C
(-25 to 120) °C 0.18 °C
(120 to 1000) °C 0.24 °C
(1000 to 1372) °C 0.33 °C

Type T (-250 to -150) °C 0.50 °C

(-150 to 0) °C 0.22 °C
(0 to 120) °C 0.18 °C
(120 to 400) °C 0.17 °C

(A2LA Cert. No. 1395.03) 7/26/2021 Page 5 of 20

 Parameter/Range Frequency CMC2, 5 (±) Comments

AC Voltage3–
Generate

Up to 2.2 mV (10 to 20) Hz 0.19 % + 4 µV Fluke calibrator

(20 to 40) Hz 0.12 % + 4 µV 5720A
40 Hz to 20 kHz 0.10 % + 4 µV
(20 to 50) kHz 0.15 % + 4 µV
(50 to 100) kHz 0.20 % + 5 µV
(100 to 300) kHz 0.36 % + 10 µV
(300 to 500) kHz 0.52 % + 20 µV
500 kHz to 1 MHz 0.65 % + 20 µV

(2.2 to 22) mV (10 to 20) Hz 0.024 % + 4 µV

(20 to 40) Hz 0.012 % + 4 µV
40 Hz to 20 kHz 0.011 % + 4 µV
(20 to 50) kHz 0.025 % + 4 µV
(50 to 100) kHz 0.053 % + 5 µV
(100 to 300) kHz 0.097 % + 10 µV
(300 to 500) kHz 0.13 % + 20 µV
500 kHz to 1 MHz 0.27 % + 20 µV

(22 to 220) mV (10 to 20) Hz 0.022 % + 12 µV

(20 to 40) Hz 95 µV/V + 7 µV
40 Hz to 20 kHz 79 µV/V + 7 µV
(20 to 50) kHz 0.019 % + 7 µV
(50 to 100) kHz 0.043 % + 17 µV
(100 to 300) kHz 0.076 % + 20 µV
(300 to 500) kHz 0.12 % + 25 µV
500 kHz to 1 MHz 0.26 % + 45 µV

220 mV to 2.2 V (10 to 20) Hz 0.024 % + 40 µV

(20 to 40) Hz 88 µV/V + 15 µV
40 Hz to 20 kHz 47 µV/V + 8 µV
(20 to 50) kHz 78 µV/V + 10 µV
(50 to 100) kHz 0.011 % + 30 µV
(100 to 300) kHz 0.036 % + 80 µV
(300 to 500) kHz 0.091 % + 0.20 mV
500 kHz to 1 MHz 0.15 % + 0.30 mV

(2.2 to 22) V (10 to 20) Hz 0.022 % + 0.40 mV Subject to a 2.2 x 107 V-

(20 to 40) Hz 89 µV/V + 0.15 mV Hz output
40 Hz to 20 kHz 47 µV/V + 50 µV
(20 to 50) kHz 77 µV/V + 0.10 mV
(50 to 100) kHz 0.010 % + 0.20 mV
(100 to 300) kHz 0.028 % + 0.60 mV
(300 to 500) kHz 0.091 % + 2 mV
500 kHz to 1 MHz 0.14 % + 3.2 mV

(A2LA Cert. No. 1395.03) 7/26/2021 Page 6 of 20

 Parameter/Range Frequency CMC2, 5 (±) Comments

AC Voltage3 –
Generate (cont)

(22 to 220) V (10 to 20) Hz 0.022 % + 4.0 mV Fluke calibrator 5720A

(20 to 40) Hz 88 µV/V + 1.5 mV w/Fluke amplifier
40 Hz to 20 kHz 53 µV/V + 0.60 mV 5725A (max. output =
(20 to 50) kHz 87 µV/V + 1.0 mV 250 V for [15 to 50] Hz)
(50 to 100) kHz 0.014 % + 2.5 mV
(100 to 300) kHz 0.080 % + 16 mV
(300 to 500) kHz 0.42 % + 40 mV
500 kHz to 1 MHz 0.70 % + 80 mV

(220 to 1100) V (15 to 50) Hz 0.026 % + 16 mV Fluke calibrator

50 Hz to 1 kHz 70 µV/V + 3.5 mV 5720A

(220 to 750) V (30 to 50) kHz 0.037 % + 11 mV

(50 to 100) kHz 0.14 % + 45 mV

(750 to 1100) V 40 Hz to 1 kHz 87 µV/V + 4 mV

(1 to 20) kHz 0.013 % + 6 mV
(20 to 30) kHz 0.037 % + 11 mV

AC Voltage3 –
Measure

(0.6 to 2.2) mV (10 to 20) Hz 0.14 % + 1 µV Fluke AC standard

(20 to 40) Hz 0.062 % + 1 µV 5790A
40 Hz to 20 kHz 0.039 % + 1 µV
(20 to 50) kHz 0.067 % + 1.6 µV
(50 to 100) kHz 0.097 % + 2 µV
(100 to 300) kHz 0.18 % + 3.2 µV
(300 to 500) kHz 0.19 % + 6.3 µV
500 kHz to 1 MHz 0.31 % + 6.3 µV

(2.2 to 7) mV (10 to 20) Hz 0.068 % + 1 µV

(20 to 40) Hz 0.030 % + 1 µV
40 Hz to 20 kHz 0.019 % + 1 µV
(20 to 50) kHz 0.033 % + 1.6 µV
(50 to 100) kHz 0.048 % + 2 µV
(100 to 300) kHz 0.097 % + 3.2 µV
(300 to 500) kHz 0.11 % + 6.3 µV
500 kHz to 1 MHz 0.19 % + 6.3 µV

(A2LA Cert. No. 1395.03) 7/26/2021 Page 7 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

AC Voltage3 –
Measure (cont)

(7 to 22) mV (10 to 20) Hz 0.024 % + 1 µV Fluke AC standard

(20 to 40) Hz 0.016 % + 1 µV 5790A
40 Hz to 20 kHz 96 µV/V + 1 µV
(20 to 50) kHz 0.017 % + 1.6 µV
(50 to 100) kHz 0.026 % + 2 µV
(100 to 300) kHz 0.067 % + 3.2 µV
(300 to 500) kHz 0.074 % + 6.3 µV
500 kHz to 1 MHz 0.14 % + 6.3 µV

(22 to 70) mV (10 to 20) Hz 0.022 % + 1.2 µV

(20 to 40) Hz 0.012 % + 1.2 µV
40 Hz to 20 kHz 74 µV/V + 1.2 µV
(20 to 50) kHz 0.013 % + 1.6 µV
(50 to 100) kHz 0.025 % + 2 µV
(100 to 300) kHz 0.048 % + 3.2 µV
(300 to 500) kHz 0.063 % + 6.3 µV
500 kHz to 1 MHz 0.097 % + 6.3 µV

(70 to 220) mV (10 to 20) Hz 0.018 % + 1.2 µV

(20 to 40) Hz 71 µV/V + 1.2 µV
40 Hz to 20 kHz 36 µV/V + 1.2 µV
(20 to 50) kHz 68 µV/V + 1.6 µV
(50 to 100) kHz 0.015 % + 2 µV
(100 to 300) kHz 0.024 % + 3.2 µV
(300 to 500) kHz 0.033 % + 6.3 µV
500 kHz to 1 MHz 0.082 % + 6.3 µV

(220 to 700) mV (10 to 20) Hz 0.017 % + 1.2 µV

(20 to 40) Hz 70 µV/V + 1.2 µV
40 Hz to 20 kHz 29 µV/V + 1.2 µV
(20 to 50) kHz 46 µV/V + 1.6 µV
(50 to 100) kHz 66 µV/V + 2 µV
(100 to 300) kHz 0.017 % + 3.2 µV
(300 to 500) kHz 0.026 % + 6.3 µV
500 kHz to 1 MHz 0.077 % + 6.3 µV

700 mV to 2.2 V (10 to 20) Hz 0.016 %

(20 to 40) Hz 56 µV/V
40 Hz to 20 kHz 21 µV/V
(20 to 50) kHz 40 µV/V
(50 to 100) kHz 58 µV/V
(100 to 300) kHz 0.016 %
(300 to 500) kHz 0.022 %
500 kHz to 1 MHz 0.075 %

(A2LA Cert. No. 1395.03) 7/26/2021 Page 8 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

AC Voltage3 –
Measure (cont)

(2.2 to 7) V (10 to 20) Hz 0.017 % Fluke AC standard

(20 to 40) Hz 57 µV/V 5790A
40 Hz to 20 kHz 22 µV/V
(20 to 50) kHz 44 µV/V
(50 to 100) kHz 67 µV/V
(100 to 300) kHz 0.018 %
(300 to 500) kHz 0.033 %
500 kHz to 1 MHz 0.098 %

(7 to 22) V (10 to 20) Hz 0.016 %

(20 to 40) Hz 57 µV/V
40 Hz to 20 kHz 24 µV/V
(20 to 50) kHz 40 µV/V
(50 to 100) kHz 67 µV/V
(100 to 300) kHz 0.017 %
(300 to 500) kHz 0.033 %
500 kHz to 1 MHz 0.098 %

(22 to 70) V (10 to 20) Hz 0.016 %

(20 to 40) Hz 58 µV/V
40 Hz to 20 kHz 29 µV/V
(20 to 50) kHz 55 µV/V
(50 to 100) kHz 81 µV/V
(100 to 300) kHz 0.017 %
(300 to 500) kHz 0.033 %
500 kHz to 1 MHz 0.095 %

(70 to 220) V (10 to 20) Hz 0.016 %

(20 to 40) Hz 58 µV/V
40 Hz to 20 kHz 31 µV/V
(20 to 50) kHz 57 µV/V
(50 to 100) kHz 81 µV/V
(100 to 300) kHz 0.017 %
(300 to 500) kHz 0.040 %

(220 to 700) V (10 to 20) Hz 0.016 %

(20 to 40) Hz 80 µV/V
40 Hz to 20 kHz 38 µV/V
(20 to 50) kHz 0.011 %
(50 to 100) kHz 0.040 %

(700 to 1000) V (10 to 20) Hz 0.016 %

(20 to 40) Hz 80 µV/V
40 Hz to 20 kHz 36 µV/V
(20 to 50) kHz 0.011 %
(50 to 100) kHz 0.040 %

(A2LA Cert. No. 1395.03) 7/26/2021 Page 9 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

AC Voltage3 –
Measure (cont)

(1 to 65) kV (50 to 60) Hz 0.60 % Ross VD90-16.5Y-AK-K

and Fluke 8508A

AC Flatness3 –
Measure

(0.6 to 2.2) mV (10 to 30) Hz 0.089 % Fluke 5790A wideband

30 Hz to 120 kHz 0.051 %
120 kHz to 2 MHz 0.064 % + 0.78 μV
(2 to 10) MHz 0.14 % + 0.78 μV
(10 to 20) MHz 0.25 % + 0.78 μV
(20 to 30) MHz 0.56 % + 1.6 μV

(2.2 to 7) mV (10 to 30) Hz 0.082 %

30 Hz to 120 kHz 0.048 %
120 kHz to 2 MHz 0.058 % + 0.78 μV
(2 to 10) MHz 0.087 % + 0.78 μV
(10 to 20) MHz 0.15 % + 0.78 μV
(20 to 30) MHz 0.32 % + 0.78 μV

(7 to 22) mV (10 to 30) Hz 0.081 %

30 Hz to 120 kHz 0.04 %
120 kHz to 2 MHz 0.058 %
(2 to 10) MHz 0.087 %
(10 to 20) MHz 0.15 %
(20 to 30) MHz 0.32 %

(22 to 70) mV (10 to 30) Hz 0.081 %

30 Hz to 120 kHz 0.04 %
120 kHz to 2 MHz 0.043 %
(2 to 10) MHz 0.085 %
(10 to 20) MHz 0.13 %
(20 to 30) MHz 0.3 %

(70 to 220) mV (10 to 30) Hz 0.08 %

30 Hz to 120 kHz 0.033 %
120 kHz to 2 MHz 0.043 %
(2 to 10) MHz 0.084 %
(10 to 20) MHz 0.13 %
(20 to 30) MHz 0.3 %

(A2LA Cert. No. 1395.03) 7/26/2021 Page 10 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

AC Flatness3 –
Measure (cont)

220 mV to 7 V (10 to 30) Hz 0.08 % Fluke 5790A wideband

30 Hz to 120 kHz 0.025 %
120 kHz to 2 MHz 0.043 %
(2 to 10) MHz 0.083 %
(10 to 20) MHz 0.13 %
(20 to 30) MHz 0.3 %

AC Current3 –
Generate

Up to 220 µA (10 to 20) Hz 0.024 % + 16 nA Fluke calibrator 5720A

(20 to 40) Hz 0.015 % + 10 nA w/Fluke 5725A
40 Hz to 1 kHz 0.012 % + 8 nA
(1 to 5) kHz 0.030 % + 12 nA
(5 to 10) kHz 0.094 % + 65 nA

220 µA to 2.2 mA (10 to 20) Hz 0.024 % + 40 nA

(20 to 40) Hz 0.015 % + 35 nA
40 Hz to 1 kHz 0.012 % + 35 nA
(1 to 5) kHz 0.019 % + 110 nA
(5 to 10) kHz 0.090 % + 0.65 µA

(2.2 to 22) mA (10 to 20) Hz 0.026 % + 0.40 µA

(20 to 40) Hz 0.015 % + 0.35 µA
40 Hz to 1 kHz 0.012 % + 0.35 µA
(1 to 5) kHz 0.019 % + 0.55 µA
(5 to 10) kHz 0.090 % + 5 µA

(22 to 220) mA (10 to 20) Hz 0.026 % + 4 µA

(20 to 40) Hz 0.015 % + 3.5 µA
40 Hz to 1 kHz 0.012 % + 2.5 µA
(1 to 5) kHz 0.019 % + 3.5 µA
(5 to 10) kHz 0.092 % + 10 µA

220 mA to 2.2 A 20 Hz to 1 kHz 0.025 % + 35 µA

(1 to 5) kHz 0.040 % + 80 µA
(5 to 10) kHz 0.60 % + 0.16 mA

(2.2 to 11) A 40 Hz to 1 kHz 0.050 % + 0.17 mA

(1 to 5) kHz 0.090 % + 0.38 mA
(5 to 10) kHz 0.33 % + 0.75 mA

(A2LA Cert. No. 1395.03) 7/26/2021 Page 11 of 20

 Parameter/Range Frequency CMC2, 5 (±) Comments

AC Current – Clamp
Meters3–

(0 to 500) A (45 to 440) Hz 0.37 % + 0.1 A Fluke 5522A w/5500

(500 to 1000) A (45 to 440) Hz 0.39 % + 0.2 A coil

AC Current3 –
Measure

Up to 200 µA 10 Hz to 10 kHz 0.037 % + 20 nA Fluke DMM 8508A

200 µA to 2 mA 10 Hz to 10 kHz 0.031 % + 200 nA

(2 to 20) mA 10 Hz to 10 kHz 0.032 % + 2 µA

(20 to 200) mA 10 Hz to 10 kHz 0.030 % + 20 µA

200 mA to 2 A 10 Hz to 2 kHz 0.062 % + 200 µA

(2 to 10) kHz 0.075 % + 200 µA

(2 to 20) A 10 Hz to 2 kHz 0.082 % + 2 mA

(2 to 10) kHz 0.25 % + 2 mA

Oscilloscope3 –

DC Signal ± 1 mV to ± 200 Vdc 0.061 % + 25 μV Fluke 9500B scope

(into 50 Ω) calibrator w/
9530 heads
± 1 mV to ± 50 Vdc
(into 1 MΩ)

40 μV to <1 mVpk-pk 0.83 % + 10 μV

1 mV to 200 Vpk-pk 0.16 % + 10 μV

50 kHz Reference 1.2 %

Amplitude

0.1 Hz to 300 MHz 2.2 %

(>300 to 550) MHz 2.5 %
(>0.55 to 2.5) GHz 2.8 %

(>2.5 to 3.0) GHz 2.8 %

Rise/Fall Times (350 to 550) ps 33 ps

10 Hz to 2 MHz

(A2LA Cert. No. 1395.03) 7/26/2021 Page 12 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

Oscilloscope3 – (cont)

Rise/Fall Times (125 to 175) ps 14 ps Fluke 9500B scope

10 Hz to 2 MHz calibrator w/ 9530 heads

Timing Marker 9.0091 ns to <83 μs 0.2 μs/s

Functions ≥83 μs to 55 s 2.3 μs/s

Pulse Width (1 to 100) ns 4.1 % + 200 ps

Inductance3 – Measure

(100 to 200) μH 1 kHz, 120 Hz 0.58 % Gen Rad 1657 RLC bridge
200 µH to 200 H 0.25 %

Capacitance3 – Generate

(0.19 to 0.3999) nF 10 Hz to 10 kHz 0.61 % + 7.8 pF Fluke calibrator 5522A

(0.4 to 1.0999) nF 10 Hz to 10 kHz 0.44 % + 7.8 pF
(1.1 to 3.2999) nF 10 Hz to 3 kHz 0.42 % + 7.8 pF
(3.3 to 10.9999) nF 10 Hz to 1 kHz 0.24 % + 7.8 pF
(11 to 32.9999) nF 10 Hz to 1 kHz 0.23 % + 7.8 pF
(33 to 109.999) nF 10 Hz to 1 kHz 0.23 % + 7.8 pF
(110 to 329.999) nF 10 Hz to 1 kHz 0.23 % + 0.23 nF

(0.33 to 1.099 99) µF 10 Hz to 600 Hz 0.23 % + 0.8 nF

(1.1 to 3.299 99) µF (10 to 300) Hz 0.23 % + 2.3 nF
(3.3 to 10.9999) µF (10 to 150) Hz 0.23 % + 7.8 nF
(11 to 32.9999) µF (10 to 120) Hz 0.33 % + 23 nF
(33 to 109.999) µF (10 to 80) Hz 0.37 % + 78 nF
(110 to 329.999) µF (0 to 50) Hz 0.37 % + 0.23 µF

(0.33 to 1.099 99) mF (0 to 20) Hz 0.37 % + 0.8 µF

(1.1 to 3.2999) mF (0 to 6) Hz 0.37 % + 2.3 µF
(3.3 to 10.9999) mF (0 to 2) Hz 0.37 % + 8 µF
(11 to 32.9999) mF (0 to 0.6) Hz 0.59 % + 23 µF
(33 to 110) mF (0 to 0.2) Hz 0.86 % + 78 µF

100 pF 1 kHz 12 µF/F ITE 1404B capacitor

1000 pF 1 kHz 18 µF/F IET 1404A capacitor

(1, 10) pF 1 kHz 0.13 % Ultra Agilent 16380A/16380C

(100, 1000) pF Conservative standard air capacitor
(0.01, 0.1, 1) µF set, BNC 4 terminal pair

(A2LA Cert. No. 1395.03) 7/26/2021 Page 13 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

Capacitance3 –
Generate (cont)

Fixed Points

1 pF 1 MHz 0.12 % Agilent 16380A/16380C

2 MHz 0.12 % standard air capacitor set,
3 MHz 0.13 % BNC 4 terminal pair
4 MHz 0.14 %
5 MHz 0.15 %
10 MHz 0.28 %
13 MHz 0.39 %

10 pF 1 MHz 0.12 %
2 MHz 0.12 %
3 MHz 0.12 %
4 MHz 0.12 %
5 MHz 0.12 %
10 MHz 0.12 %
13 MHz 0.12 %

100 pF 1 MHz 0.12 %

2 MHz 0.12 %
3 MHz 0.12 %
4 MHz 0.12 %
5 MHz 0.12 %
10 MHz 0.13 %
13 MHz 0.13 %

1000 pF 1 MHz 0.12 %

2 MHz 0.12 %
3 MHz 0.12 %
4 MHz 0.13 %
5 MHz 0.14 %
10 MHz 0.23 %
13 MHz 0.31 %

Capacitance3 –
Measure

1 pF to 1 µF 1 kHz 61 µF/F Andeen Hagerling 2500A

capacitance bridge

(1.0 to 200) µF 120 Hz, 1 kHz 0.25 % GenRad 1657 RLC bridge
200 µF to 1 mF 1.2 %

(A2LA Cert. No. 1395.03) 7/26/2021 Page 14 of 20

III. Electrical – RF/Microwave

Parameter/Range Frequency CMC2, 4, 5 (±) Comments

RF Power3 – Generate

(+13 to -5) dBm 200 Hz to 80 MHz 0.09 dB HP 3335A generator

(-6 to -45) dBm 0.13 dB
(-46 to -85) dBm 0.20 dB

(+20 to -100) dBm 2.5 MHz to 26.5 GHz 0.6 dB HP 8340B synthesizer
w/ HP 8902 audio
analyzer; HP 11722A,
HP 11792A sensors, HP
1793A converter

RF Power3 – Measure

1 mW for 50 Ω (1 to 30) MHz 0.94 % HP 478A-H75

Reference 50 MHz 0.39 % thermistor mount w/
(50 to 100) MHz 0.53 % Agilent N432A power
(100 to 500) MHz 0.65 % meter
(0.5 to 1) GHz 0.79 %

(-20 to + 30) dBm 100 kHz to 2.6 GHz 0.063 dB + 1 digit HP 8902A measuring
50 MHz to 26.5 GHz 0.13 dB + 1 digit receiver w/ HP 11792A
power sensor

Tuned RF Power –
Measure (Relative)
(+10 to 0) dB (0.15 to 1300) MHz 0.035 dB + 1 digit HP 8902A measuring
(0 to -10) dB 0.035 dB + 1 digit receiver w/ HP 11722A
(-10 to -20) dB 0.040 dB + 1 digit power sensor
(-20 to -30) dB 0.045 dB + 1 digit
(-30 to -40) dB 0.051 dB + 1 digit
(-40 to -50) dB 0.058 dB + 1 digit
(-50 to -60) dB 0.058 dB + 1 digit
(-60 to -70) dB 0.064 dB + 1 digit
(-70 to -80) dB 0.070 dB + 1 digit
(-80 to -90) dB 0.076 dB + 1 digit
(-90 to -100) dB 0.083 dB + 1 digit
(-100 to -110) dB 0.14 dB + 1 digit
(-110 to -120) dB 0.19 dB + 1 digit

(A2LA Cert. No. 1395.03) 7/26/2021 Page 15 of 20

 Parameter/Range Frequency CMC2, 5 (±) Comments

Tuned RF Power – Measure

(Relative)
(cont)
(+10 to 0) dB (1.3 to 26.5) GHz 0.035 dB + 1 digit HP 8902A measuring
(0 to -10) dB 0.035 dB + 1 digit receiver w/ HP 11793A
(-10 to -20) dB 0.040 dB + 1 digit converter, HP 11792A
(-20 to -30) dB 0.045 dB + 1 digit power sensor
(-30 to -40) dB 0.051 dB + 1 digit
(-40 to -50) dB 0.058 dB + 1 digit
(-50 to -60) dB 0.14 dB + 1 digit
(-60 to -70) dB 0.19 dB + 1 digit
(-70 to -80) dB 0.25 dB + 1 digit
(-80 to -90) dB 0.31 dB + 1 digit

Amplitude Modulation3 –
Measure

Rate: 50 Hz to 10 kHz 150 kHz to 10 MHz 2.1 % + 1 digit HP 8902A measuring

Depth: (5 to 99) % receiver w/ HP
11793A converter, HP
Rate: 20 Hz to 10 kHz 3.0 % + 1 digit 11792A power sensor
Depth: To 99 %

Rate: 50 Hz to 50 kHz (10 to 1300) MHz 1.1 % + 1 digit

Depth: (5 to 99) %

Rate: 20 Hz to 100 kHz 3.0 % + 1 digit

Depth: To 99 %

Rate: 50 Hz to 50 kHz (1.3 to 26.5) GHz 1.6 % + 1 digit

Depth: (5 to 99) %

Rate: 20 Hz to 100 kHz 3.0 % + 1 digit

Depth: To 99 %

(A2LA Cert. No. 1395.03) 7/26/2021 Page 16 of 20

 Parameter/Range Frequency CMC2, 4, 5 (±) Comments

Frequency Modulation3 –
Measure

Rate: 20 Hz to 10 kHz 250 kHz to 10 MHz 2.0 % + 1 digit HP 8902A measuring

Dev.: ≤ 40 kHz peak receiver

Rate: 50 Hz to 100 kHz (10 to 1300) MHz 1.1 % + 1 digit

Dev.: ≤ 400 kHz peak

Rate: 20 Hz to 200 kHz

Dev.: ≤ 400 kHz peak (10 to 1300) MHz 5.0 % + 1 digit

Phase Modulation –
Measure

Rate: 200 Hz to 10 kHz 150 kHz to 10 MHz 4 % + 0.015 rad HP 8902A measuring
receiver w/
Rate: 20 Hz to 200 kHz 10 MHz to 26.5 GHz 5 % + 0.019 rad HP 11792A power
sensor

Harmonic Distortion –
Measure

≤ -80 dB ≤20 Hz to 20 kHz 1.0 dB HP 8903B audio

analyzer

≤ -65 dB (20 to 100) kHz 2.0 dB HP 8563E spectrum

>100 kHz to 13.2 GHz 2.7 dB analyzer

In Line RF Power Meters –

(1 to 80) W (0.1 to 500) MHz 1.7 % RF Attenuator, Agilent

(0.5 to 1.0) GHz 1.9 % 478-H75 w/8482,
Agilent N478 w/8482,
AR amplifier

(A2LA Cert. No. 1395.03) 7/26/2021 Page 17 of 20

IV. Mechanical

Parameter/Equipment Range CMC2, 4, 7 (±) Comments

Scales & Balances3 (1 to 500) mg 0.024 mg + 0.6R Class 1 weights

(0.5 to 5) g 0.040 mg + 0.6R
(5 to 20) g 0.078 mg + 0.6R
(20 to 500) g 2.5 µg/g + 0.6R
(0.5 to 5) kg 5.4 µg/g + 0.6R Class 2 weights
(10 to 500) lb 0.010 % + 0.6R Class F weights

Pressure3 –
Measuring Equipment

Nitrogen Gas (0 to 90) psia 0.0021 % + 0.009 psia + 0.58R Additel ADT780
(>90 to 300) psia 0.0054 % + 0.015 psia + 0.6R pressure calibrator

(300 to 1000) psia 0.01 % + 0.01 psia + 0.6R

Hydraulic (-14.5 to 300) psig 0.0054 % + 0.015 psi + 0.6R Crystal reference
(300 to 1000) psig 0.01 % + 0.01 psi + 0.6R pressure gauge

(1000 to 2000) psi 0.011 % + 2.1 psi + 0.6R

(2000 to 10 000) psi 0.10 % + 0.45 psi + 0.6R

Torque – Measuring (1 to 10) ozf∙in 1.4 % Digital torque load

Equipment3 (10 to 100) ozf∙in 1.7 % cells
(5 to 50) lbf∙in 0.64 % + 0.58R
50 lbf∙in to 250 lbf∙ft 1.7 %

V. Thermodynamics

Parameter/Equipment Range CMC2, 7 (±) Comments

Temperature3 – (-80 to 0) °C 0.025 °C Monitored by Hart

Measuring Equipment (0 to 420) °C 0.061 °C Scientific 5626 PRT/
(420 to 660) °C 0.12 °C Fluke 8508A DMM,
Wahl IPR4-1 ice point
reference for 0 °C and
mixture dry ice/alcohol
for below 0 °C

(50 to 420) °C 0.14 °C Fluke 9144 dry well

(420 to 660) °C 0.17 °C

(A2LA Cert. No. 1395.03) 7/26/2021 Page 18 of 20

 Parameter/Equipment Range CMC2, 7 (±) Comments

Temperature3 – (-200 to 400) °C 0.018 °C Hart Scientific 5626

Measure (400 to 660) °C 0.020 °C PRT w/Fluke 8508A
DMM

Relative Humidity – (10 to 90) % RH 1.2 % RH Temperature/RH data

Measure3 recorder Veriteq SP2000

Relative Humidity – (11 to 80) % RH 1.2 % RH Temperature/RH data

Measuring Equipment recorder Veriteq SP2000

VI. Time & Frequency

Parameter/Equipment Range CMC2, 4, 7 (±) Comments

Frequency Reference 10 MHz Reference 1.8 × 10-12 Hz/Hz Fluke 910 GPS receiver
Signal

Frequency3 – 1 µHz to 26.5 GHz 1.8 × 10-12 Hz/Hz +0.6R GPS receiver w/
Measuring Equipment synthesized generator

Frequency3 – Measure DC to 225 MHz 1.5 × 10-9 Hz/Hz + 5 µHz GPS receiver w/
53132 counter

225 MHz to 26.5 GHz 1.8 × 10-12 Hz/Hz + 1.3 5343A counter
Hz

Stopwatches and (0 to 19.99) s/day 0.12 s/day Timometer

Timers3
__________________________________________________________

1
This laboratory offers commercial calibration service and field calibration service.
2
Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement
that a laboratory can achieve within its scope of accreditation when performing more or less routine
calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMC represent
expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage
factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory
may be greater than the CMC due to the behavior of the customer’s device and to influences from the
circumstances of the specific calibration.

(A2LA Cert. No. 1395.03) 7/26/2021 Page 19 of 20

3
Field calibration service is available for this calibration. Please note the actual measurement uncertainties
achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA
Scope. Allowance must be made for aspects such as the environment at the place of calibration and for
other possible adverse effects such as those caused by transportation of the calibration equipment. The
usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must
also be considered and this, on its own, could result in the actual measurement uncertainty achievable on
a customer’s site being larger than the CMC.
4
In the statement of CMC, L is defined as the length of the unit under test in inches, D is the diameter of
the unit under test in inches, R is the resolution of the device under test and % is percentage of reading,
unless otherwise indicated.
5
The stated measured values are determined using the indicated instrument (see Comments). This
capability is suitable for the calibration of the devices intended to measure or generate the measured value
in the ranges indicated. CMC are expressed as either a specific value that covers the full range or as a
percent or fraction of the reading plus a fixed floor specification.
6
This scope meets A2LA’s P112 Flexible Scope Policy.
7
The type of instrument or material being calibrated is defined by the parameter. This indicates the
laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated
for the listed measurement parameter.

(A2LA Cert. No. 1395.03) 7/26/2021 Page 20 of 20

 Accredited Laboratory
A2LA has accredited

SIMCO ELECTRONICS, INC.

Ricardson, TX
for technical competence in the field of

Calibration
This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017 General
requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSL
Z540-1-1994 and the requirements of ANSI/NCSL Z540.3-2006 and R205 – Specific Requirements: Calibration Laboratory
Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a
laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017).

Presented this 26th day of July 2021.

_______________________
Vice President, Accreditation Services
For the Accreditation Council
Certificate Number 1395.03
Valid to September 30, 2023

For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation.