SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017

EL AL STANDARDS LABORATORY
EL AL Head Office
Ben-Gurion Airport
Israel
Erez Lee Yadgar Phone: 972 3 9716596
Mobile: 972 54 4337757

CALIBRATION

Valid To: July 31, 2023 Certificate Number: 4282.01

In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this
laboratory to perform the following calibrations1, 5:

I. Dimensional

Parameter/Equipment Range CMC2 () Comments

Calipers Up to 25.4 mm 18 µm (710 µin) Gage blocks, caliper

(25.4 to 76.2) mm 23 µm (890 µin) checker
(76.2 to 101.6) mm 24 µm (940 µin)
(101.6 to 152.4) mm 28 µm (1100 µin)
(152.4 to 254) mm 33 µm (1300 µin)
(254 to 304.8) mm 41 µm (1600 µin)
(304.8 to 406.4) mm 48 µm (1900 µin)
(406.4 to 609.6) mm 56 µm (2200 µin)

Micrometers Up to 2.7 mm 2.2 µm (88 µin) Gage blocks

(2.7 to 5.3) mm 2.3 µm (91 µin)
(5.3 to 12.7) mm 2.3 µm (92 µin)
(12.7 to 20.7) mm 2.4 µm (94 µin)
(20.7 to 25.4) mm 2.5 µm (100 µin)
(25.4 to 50.8) mm 3.0 µm (120 µin)
(50.8 to 101.6) mm 4.3 µm (170 µin)
(101.6 to 152.4) mm 5.0 µm (200 µin)
(152.4 to 203.2) mm 6.0 µm (240 µin)
(203.2 to 406.4) mm 7.5 µm (320 µin)

(A2LA Cert. No. 4282.01) 10/22/2021 Page 1 of 10

 Parameter/Equipment Range CMC2 () Comments

Depth Micrometers Up to 50.8 mm 3.0 µm (120 µin) Gage blocks

(50.8 to 76.2) mm 3.5 µm (140 µin)
(76.2 to 101.6) mm 4.3 µm (170 µin)
(101.6 to 152.4) mm 4.8 µm (190 µin)
(152.4 to 203.2) mm 5.3 µm (210 µin)
(203.4 to 304.8) mm 6.6 µm (260 µin)

Length Standards Up to 100 mm 2.8 µm (110 µin) Height gage

(Extension Rods, (100 to 200) mm 2.9 µm (110 µin)
Micrometer Settings (200 to 300) mm 3.6 µm (140 µin)
Standards) (300 to 400) mm 4.5 µm (180 µin)
(400 to 600) mm 5.3 µm (210 µin)

Height Gages Up to 25.4 mm 2.0 µm (81 µin) Gage blocks

(25.4 to 50.8) mm 2.5 µm (97 µin)
(50.8 to 101.6) mm 3.8 µm (150 µin)
(101.6 to 152.4) mm 5.8 µm (230 µin)
(152.4 to 203.2) mm 7.3 µm (290 µin)
(203.2 to 254) mm 9.1 µm (360 µin)
(254.0 to 330.2) mm 12 µm (460 µin)
(330.2 to 457.2) mm 16 µm (630 µin)
(457.2 to 508.0) mm 18 µm (700 µin)
(508.0 to 609.6) mm 22 µm (850 µin)

Cylindrical Gages Up to 25.4 mm 3.3 µm Micrometer

(Pin Gages)

II. Electrical – DC/Low Frequency

Parameter/Equipment Range CMC2 () Comments

Resistance – Up to 0.5 mΩ 0.28 µΩ Shunts

Micro Ohmmeter (0.5 to 10) mΩ 7.1 µΩ

Decade Box (10 to 100) Ω 0.015 Ω DMM

(100 to 1000) Ω 0.016 Ω
(1 to 10) kΩ 0.37 Ω
(10 to 100) kΩ 12 Ω
(100 to 1000) kΩ 0.015 kΩ
(1 to 10) MΩ 0.001 MΩ

(A2LA Cert. No. 4282.01) 10/22/2021 Page 2 of 10

 Parameter/Equipment Range CMC2, 6 () Comments

DC Current – Measuring (0 to 5) A 7 mA Comparison reading

Equipment (Ammeter) (5 to 10) A 9 mA with standard DMM

DC Voltage – Measuring (0 to 5) V 1.2 mV Comparison reading

Equipment (Voltmeter) (5 to 50) V 12 mV with standard DMM

DC Power Supply –

DC Voltage (0 to 5) V 0.9 mV Comparison reading

(5 to 50) V 10 mV with standard DMM
(50 to 400) V 120 mV

DC Current (0 to 0.5) A 0.54 mA

(0.5 to 5) A 7 mA
(5 to 10) A 7 mA
(10 to 50) A 38 mA
(50 to 100) A 50 mA

Clamp – Meters

DC Volt (100 to 600) V 0.2 V Comparison reading

with standard DMM,
DC Current (0 to 0.5) A 0.8 mA coil
(0.5 to 3) A 7 mA
(3 to 10) A 9 mA
(10 to 20) A 40 mA
(20 to 600) A 2A

AC Volt (50/400 Hz) (100 to 600) V 0.3 V

AC Current (50/400 (0 to 4) A 0.9 mA

Hz) (4 to 10) A 20 mA
(10 to 20) A 42 mA
(20 to 200) A 1A
(200 to 600) A 4.9 A

(50 to 500) Ω 0.1 mΩ

Resistance (500 to 6000) Ω 0.58 mΩ
(6 to 20) kΩ 5.8 mΩ

(A2LA Cert. No. 4282.01) 10/22/2021 Page 3 of 10

 Parameter/Equipment Range CMC2, 4, 6 () Comments

Resistance – Measuring 0 Ω? 5.8 mΩ Fluke 5522A

Equipment (DMM) (0 to 11) Ω 40 µΩ/Ω multi – product
11 Ω to 1 MΩ 32 µΩ/Ω calibrator
(1.1 to 3.3) MΩ 60 µΩ/Ω
(3.3 to 11) MΩ 130 µΩ/Ω
(11 to 33) MΩ 250 µΩ/Ω
(33 to 110) MΩ 500 µΩ/Ω
(110 to 330) MΩ 3000 µΩ/Ω
(330 to 1100) MΩ 15 000 µΩ/Ω

Capacitance – Measuring (220 to 400) pF 0.5 % + 10 pF Fluke 5522A multi –

Equipment (DMM) (0.4 to 1.1) nF 0.5 % + 0.01 nF product calibrator
(1.1 to 3.3) nF 0.5 % + 0.01 nF
(3.3 to 11) nF 0.25 % + 0.01 nF
(11 to 33) nF 0.25 % + 0.01 nF
(33 to 110) nF 0.25 % + 0.01 nF
(110 to 330) nF 0.25 % + 0.03 nF
(0.33 to 1.1) µF 0.25 % + 1 nF
(1.1 to 3.3) µF 0.25 % + 3 nF
(3.3 to 11) µF 0.25 % + 10 nF
(11 to 33) µF 0.4 % + 30 nF
(33 to 110) µF 0.45 % + 100 nF
(110 to 330) µF 0.45 % + 300 nF
(0.33 to 1.1) mF 0.40 % + 1 µF
(1.1 to 3.3) mF 0.45 % + 3 µF
(3.3 to 11) mF 0.45 % + 10 µF
(11 to 33) mF 0.75 % + 30 µF
(33 to 110) mF 1.1 % + 100 µF

DC Voltage – Measuring (0 to 330) mV 20 µV/V + 1 µV Fluke 5522A multi –

Equipment (DMM) (0 to 3.3) V 11 µV/V + 2 µV product calibrator
(3.3 to 32.3) V 12 µV/V + 20 µV
(30 to 330) V 18 µV/V + 150 µV
(100 to 1020) V 18 µV/V + 1500 µV

DC Current – Measuring Up to 330 µA 150 µA/A + 0.02 µA Fluke 5522A multi –

Equipment (DMM) (0.3 to 3.3) mA 100 µA/A + 0.05 µA product calibrator
(3.3 to 33) mA 100 µA/A + 0.25 µA
(33 to 330) mA 100 µA/A + 2.5 µA
(0.3 to 1.1) A 200 µA/A + 40 µA
(1.1 to 3) A 380 µA/A + 40 µA
(3 to 11) A 500 µA/A + 500 µA
(11 to 25) A 1000 µA/A + 750 µA

(A2LA Cert. No. 4282.01) 10/22/2021 Page 4 of 10

 Parameter/Range Frequency CMC2, 6 () Comments

AC Voltage – Measuring
Equipment (Voltmeter)

(0 to 5) V 50 Hz and 400 Hz 27 mV Comparison reading

(5 to 50) V 38 mV with standard DMM
(50 to 250) V 380 mV

AC Current – Measuring
Equipment (Ammeter)

(0 to 5) A 50 Hz and 400 Hz 1.1 mA Comparison reading

(5 to 10) A 19 mA with standard DMM
(10 to 20) A 38 mA

Power Supply – AC Volts

(0 to 5) V (50 and 400) Hz 27 mV Comparison reading

(5 to 50) V 36 mV with standard DMM
(50 to 300) V 380 mV

Power Supply –
AC Current

(0 to 5) A (50 and 400) Hz 5.8 mA Comparison reading

(5 to 10) A 34 mA with standard DMM

(A2LA Cert. No. 4282.01) 10/22/2021 Page 5 of 10

 Parameter/Range Frequency CMC2, 6 () Comments

AC Voltage – Measuring
Equipment (DMM)

(1 to 33) mV (10 to 45) Hz 800 µV/V + 6 µV Fluke 5522A multi –

45 Hz to 10 kHz 150 µV/V + 6 µV product calibrator
(10 to 20) kHz 200 µV/V + 6 µV
(20 to 50) kHz 1000 µV/V + 6 µV
(50 to 100) kHz 3500 µV/V + 12 µV
(100 to 500) kHz 8000 µV/V + 50 µV

(33 to 330) mV (10 to 45) Hz 300 µV/V + 8 µV

45 Hz to 10 kHz 145 µV/V + 8 µV
(10 to 20) kHz 160 µV/V + 8 µV
(20 to 50) kHz 350 µV/V + 8 µV
(50 to 100) kHz 800 µV/V + 32 µV
(100 to 500) kHz 2000 µV/V + 70 µV

(0.33 to 3.3) V (10 to 45) Hz 300 µV/V + 50 µV

45 Hz to 10 kHz 150 µV/V + 60 µV
(10 to 20) kHz 190 µV/V + 60 µV
(20 to 50) kHz 300 µV/V + 50 µV
(50 to 100) kHz 700 µV/V + 130 µV
(100 to 500) kHz 2400 µV/V + 600 µV

(3.3 to 33 V) (10 to 45) Hz 300 µV/V + 650 µV

45 Hz to 10 kHz 150 µV/V + 600 µV
(10 to 20) kHz 240 µV/V + 600 µV
(20 to 50) kHz 350 µV/V + 600 µV
(50 to 100) kHz 900 µV/V + 1600 µV

(33 to 330 V) 45 Hz to 1 kHz 190 µV/V + 2000 µV

(1 to 10) kHz 200 µV/V + 6000 µV
(10 to 20) kHz 250 µV/V + 6000 µV
(20 to 50) kHz 300 µV/V + 6000 µV
(50 to 100) kHz 2000 µV/V + 50 000 µV

(330 to 1020 V) 45 Hz to 1 kHz 300 µV/V + 10 000 µV

(1 to 5) kHz 250 µV/V + 10 000 µV
(5 to 10) kHz 300 µV/V + 10 000 µV

(A2LA Cert. No. 4282.01) 10/22/2021 Page 6 of 10

 Parameter/Range Frequency CMC2, 6 () Comments

AC Current – Measuring
Equipment (DMM)

(29 to 330) µA (10 to 20) Hz 0.2 µA/A + 0.1 µA Fluke 5522A multi –
(20 to 45) Hz 0.15 µA/A + 0.1 µA product calibrator
45 Hz to 1 kHz 0.13 µA/A + 0.1 µA
(1 to 5) kHz 0.3 µA/A + 0.15 µA
(5 to 10) kHz 0.8 µA/A + 0.2 µA
(10 to 30) kHz 1.6 µA/A + 0.4 µA

(0.33 to 3.3) mA (10 to 20) Hz 0.2 µA/A + 0.15 µA

(20 to 45) Hz 0.13 µA/A + 0.15 µA
45 Hz to 1 kHz 0.1 µA/A + 0.15 µA
(1 to 5) kHz 0.2 µA/A + 0.2 µA
(5 to 10) kHz 0.5 µA/A + 0.3 µA
(10 to 30) kHz 1 µA/A + 0.6 µA

(3.3 to 33) mA (10 to 20) Hz 0.18 µA/A + 2 µA

(20 to 45) Hz 0.09 µA/A + 2 µA
45 Hz to 1 kHz 0.04 µA/A + 2 µA
(1 to 5) kHz 0.08 µA/A + 2 µA
(5 to 10) kHz 0.2 µA/A + 3 µA
(10 to 30) kHz 0.4 µA/A + 4 µA

(33 to 330) mA (10 to 20) Hz 0.18 µA/A + 20 µA

(20 to 45) Hz 0.09 µA/A + 20 µA
45 Hz to 1 kHz 0.04 µA/A + 20 µA
(1 to 5) kHz 0.1 µA/A + 50 µA
(5 to 10) kHz 0.2 µA/A + 100 µA
(10 to 30) kHz 0.4 µA/A + 200 µA

(0.33 to 1.1) A (10 to 45) Hz 0.18 µA/A + 100 µA

45 Hz to 1 kHz 0.05 µA/A + 100 µA
(1 to 5) kHz 0.6 µA/A + 1000 µA
(5 to 10) kHz 2.5 µA/A + 5000 µA

(1.1 to 3) A (10 to 45) Hz 0.18 µA/A + 100 µA

45 Hz to 1 kHz 0.06 µA/A + 100 µA
(1 to 5) kHz 0.6 µA/A + 1000 µA
(5 to 10) kHz 2.5 µA/A + 5000 µA

(3 to 11) A (45 to 100) Hz 0.06 µA/A + 2000 µA

100 Hz to 1 kHz 0.1 µA/A + 2000 µA
(1 to 5) kHz 3 µA/A + 2000 µA

(11 to 20.5) A (45 to 100) Hz 0.12 µA/A + 5000 µA

100 Hz to 1 kHz 0.15 µA/A + 5000 µA
(1 to 5) kHz 3 µA/A + 5000 µA

(A2LA Cert. No. 4282.01) 10/22/2021 Page 7 of 10

 Parameter/Range Range CMC2 () Comments

Insulation Tester (Megger)

–

DC Volt (100 to 600) V 0.14 V Decade box and

comparison reading
AC Volt (50/400 Hz) (100 to 600) V 0.44 V with standard DMM

Resistance 50 Ω to 1 kΩ 0.6 Ω
(1 to 20) kΩ 5.8 Ω

DC Volt Output (50 to 1000) V 0.59 V

Insulation 50 VDC (10 to 50) MΩ 24 kΩ

Insulation 100 VDC (20 to 100) MΩ 67 kΩ
Insulation 250 VDC (50 to 200) MΩ 120 kΩ
Insulation 500 VDC (150 to 500) MΩ 310 kΩ

Insulation 1000 VDC 1000 MΩ 2300 kΩ

10 000 MΩ 13 000 kΩ

III. Mechanical

Parameter/Equipment Range CMC2 () Comments

Pressure3 –

Pressure Gages – (0 to 1000) psi 0.094 psi (0.6 kPa) Druck DPI 612
Hydraulic and (1000 to 5000) psi 0.26 psi (1.8 kPa)
Pneumatic (5000 to 10 000) psi 0.80 psi (5.5 kPa)

Vacuum Gages Up to -13.7 psi 0.021 psi (0.1 kPa)

Torque, Torque Wrenches (0.056 to 0.113) N∙m 0.000 67 N∙m Torque transducers,
and Torque Drivers (0.113 to 0.565) N∙m 0.003 N∙m ISO 6789
(0.565 to 2.26) N∙m 0.0044 N∙m
(2.26 to 5.65) N∙m 0.0064 N∙m
(5.65 to 16.9) N∙m 0.036 N∙m
(16.9 to 28.2) N∙m 0.062 N∙m
(28.2 to 67) N∙m 0.092 N∙m
(67 to 340) N∙m 0.75 N∙m
(340 to 680) N∙m 1.4 N∙m
(680 to 880) N∙m 4.6 N∙m
(880 to 1320) N∙m 5.4 N∙m

(A2LA Cert. No. 4282.01) 10/22/2021 Page 8 of 10

 Parameter/Equipment Range CMC2, 4 () Comments

Scales and Balances3 –

Resolution 0.001 g Up to 400 g 0.0012 g Mass standards

Resolution 0.01 g Up to 5000 g 0.01 g OIML R/76
Resolution 0.1 g Up to 10000 g 0.091 g

Resolution 0.001 kg Up to 50 kg 0.001 kg

Resolution 0.01 kg Up to 50 kg 0.0076 kg
Resolution 0.1 kg Up to 50 kg 0.076 kg

Resolution 0.01 kg (50 to 160) kg 0.012 kg

Resolution 0.1 kg (50 to 160) kg 0.1 kg

Force3 – Force Indicators, Load cell standards

Dynamometers

Compression Up to 0.5 kN 0.27 %

(0.5 to 4.5) kN 0.17 %
(4.5 to 45) kN 0.18 %
(45 to 89) kN 0.16 %

Tension Up to 0.5 kN 0.46 %

(0.5 to 1.8) kN 0.26 %
(1.8 to 4.5) kN 0.33 %
(4.5 to 8.9) kN 0.36 %
(8.9 to 89) kN 0.18 %

Tachometers – Optical Up to 600 RPM 0.6 RPM Tachometer Shimpo

(Non-contact) (600 to 1200) RPM 2.1 RPM DT 205b
(1200 to 3000) RPM 3.0 RPM
(3000 to 6000) RPM 4.7 RPM
(6000 to 12 000) RPM 8.9 RPM
(12 000 to 600 000) RPM 41 RPM

IV. Thermodynamics

Parameter/Equipment Range CMC2, 6 () Comments

Temperature – Measure and (0 to 50) °C 0.067 °C RTD, with dry

Measuring Equipment (0 to 150) °C 0.095 °C blocks or
(150 to 200) °C 0.11 °C temperature chamber

(A2LA Cert. No. 4282.01) 10/22/2021 Page 9 of 10

 Parameter/Equipment Range CMC2, 6 () Comments

Relative Humidity – (35 to 75) % RH 1.5 % RH Rotronic hygrometer,

Measure and Measuring humidity chamber
Equipment

___________________________________________

1
This laboratory offers commercial calibration service.
2
Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement
that a laboratory can achieve within its scope of accreditation when performing more or less routine
calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMC’s
represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using
a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by
the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences
from the circumstances of the specific calibration.
3
Field calibration service is available for this calibration. Please note the actual measurement uncertainties
achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA
Scope. Allowance must be made for aspects such as the environment at the place of calibration and for
other possible adverse effects such as those caused by transportation of the calibration equipment. The
usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must
also be considered and this, on its own, could result in the actual measurement uncertainty achievable on
a customer’s site being larger than the CMC
4
In the statement of CMC, percentages are to be read as percentage of reading, unless otherwise noted.
5
This lab meets A2LA’s P112 Flexible Scope Policy.
6
The type of instrument or material being calibrated is defined by the parameter. This indicates the
laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated
for the listed measurement parameter.

(A2LA Cert. No. 4282.01) 10/22/2021 Page 10 of 10

 Accredited Laboratory
A2LA has accredited

EL AL STANDARDS LABORATORY
Tel Aviv, ISRAEL
for technical competence in the field of

Calibration
This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017
General requirements for the competence of testing and calibration laboratories. This laboratory also meets R205 – Specific
Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a
defined scope and the operation of a laboratory quality management system
(refer to joint ISO-ILAC-IAF Communiqué dated April 2017).

Presented this 22nd day of October 2021.

_______________________
Vice President, Accreditation Services
For the Accreditation Council
Certificate Number 4282.01
Valid to July 31, 2023

For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation.