in.

k200
series of compact full-function keypads
for in.xe spa systems

Single pump system

Two pump system

The Quick Reference Card provides a quick overview of your spa’s main
functions and the operations accessible with your digital control pad.

Spa functions

Key 1
Press Key 1 key to turn Pump 1 on at low speed. Press a
second time to turn pump to high speed (with a dual-speed
98 pump). A third time turns pump off.
A built-in timer automatically turns pump off after a prede-
termined period of time, unless pump has been manually
deactivated first.
The “Pump 1” indicator lights up when Pump 1 is on.
With dual-speed pump, indicator will flash when
Pump 1 is on at low speed.

Key 2 (2 Pump (or single pump/blower)

(Single-speed pump/blower)
Press Key 2 key to turn Pump 2 or Blower on. Press a
98 second time to turn pump or blower off.
(Dual-speed pump)
Press Key 2 key to turn Pump 2 on at low speed. Press
a second time to turn pump to high speed. A third time
turns pump off.
A built-in timer automatically turns pump off after a prede-
termined period of time, unless it has been manually
deactivated first.
The “Pump 2” indicator lights up when Pump 2 is on.
With dual-speed pump, indicator will flash when
Pump 2 is on at low speed.
 Key 2 (2-Pump/ Blower System)
Press Key 2 to turn Pump 2 on at high speed. Pressing a
second time turns blower on. A third press turns Pump 2 off
98 but leaves blower on. A final press turns blower off. A built-in
timer automatically turns Pump 2/blower off after a prede-
termined period of time, unless Pump 2/blower has been
manually deactivated first.
The “Pump 2” indicator lights up
when Pump 2/blower is on.

Light key
Press Light key to turn light on. Press a second time to turn
light off. A built-in timer automatically turns light off after
98 2 hours, unless it has been manually deactivated first.
The “Light” indicator lights up
when light is on.

Up/Down keys
Use Up or Down key to set desired water temperature.
The temperature setting will be displayed for 5 seconds to
98 confirm your new selection.
The "Set Point" icon indicates that the display shows the
desired temperature, NOT the current water temperature!

Off Mode
This mode allows you to stop all outputs for 30 minutes to
perform a quick spa maintenance.
Press and hold Key 1 key for 5 secs to activate the Off mode.
Quick press Key 1 key to reactivate the system before the ex-
piration of the 30-minute delay.
While the Off mode is engaged, the display will toggle
between OFF and the water temperature.

Programming the purge / filter cycles

Programming filter cycles

Depending on system configuration the system performs either purge cycles or filter cycles.
To program the filter cycles, you must enter these parameters: duration and frequency.
During a filter cycle, pumps & blower run at high speed for one minute to purge the
plumbing. Pump 1 or CP then runs at low speed for the remaining of the cycle.
 Setting filter cycle duration
Press and hold Light key until the display shows dxx, with
"xx" representing the duration in hours. (Default: 2 hours).
Use Up or Down key to change setting.
0 = no filtration
24 = continuous filtration
Note: it's not recommended to set this to "0".

Filter cycle frequency

Press Light key again. The display will show Fx, with "x"
representing the number of filter cycles per day (up to 4).
F 2 (Default: twice a day).
Use Up or Down key to change setting.
When the desired setting is displayed, press Light
key to confirm. A filter cycle will start immediately.
The “Filter” indicator lights up
when a filter cycle is on.

Setting the temperature display units

To set the temperature display units, quick press Light key
again. The display will show either°F or °C.
Use Up or Down key to change units.
Press Light key a last time to go back to normal mode.
°F = Fahrenheit
°C = Celsius

Programming purge cycles

To program the purge cycles, you must select the frequency. During a purge cycle, all pumps
and the blower run for one minute. To set purge cycles:

Purge cycle frequency

Press and hold Light key until the display shows Fx, with "x"
representing the number of purge cycles per day (up to 4).
F 2 Use Up or Down key to change setting.
When the desired setting is displayed, press Light
key to confirm. A purge cycle will start immediately.
The “Filter” indicator lights up
when a purge cycle is on.
Water temperature regulation Smart Winter Mode
In a regulation cycle, the system first Our Smart Winter Mode protects your
generates water flow through the heater system from the cold by turning pumps on
housing and the plumbing, in order several times a day to prevent water from
to ensure accurate water temperature freezing in pipes.
readings as well as avoiding heater
activation in dry conditions. The “Smart Winter Mode” indicator
lights up when the Smart Winter
After verifying pump activation and taking a Mode is on.
water temperature reading if required, the
system automatically turns the heater on to
reach and maintain water temperature at Cooldown
Set Point.
The “Heater” indicator lights up when While performing this task, the heater is not
the heater is on. It flashes when there allowed to turn on and its icon flashes.
is a request for more heat but the
heater has not yet started.

Troubleshooting

Hr
An internal hardware error has been detected in in.xe.
Contact dealer or service supplier.

HL
The system has shut the heater down because the t emperature at the heater
has reached 119°F (48°C). Do not enter the water! Remove the spa cover and
allow the water to cool down, then shut power off and power your spa up
again to reset the system.

AOH
Temperature inside the spa skirt is too high, causing the internal temperature
in the in.xe to increase above normal limits. Open skirt and wait until error
clears.

FLO
The system does not detect any water flow w  hile the primary pump is
running. Check and open water valves. Check for water level. C  lean filter.
If the problem persists, call your dealer o
 r service supplier.

Prr
A problem is detected with the temperature probe.
Call your dealer or service supplier.

OH
The water temperature in the spa has reached 108°F (42°C). D  o not enter the
water! Remove the spa cover and a llow the water to cool down to a lower
temperature. Call your dealer or service supplier if problem persists.

© Groupe Gecko Alliance Inc., 2017

All trademarks or registered trademarks
are the property of their respective owners. www.geckoalliance.com 9919-101135-B