Doc.no.

LEC-OM03203

Product name

Electric actuator controller

Gateway (GW) unit (EtherNet IP type)

Model / Series

LEC-GEN1
Contents
1. Safety Instructions................................................................. 4

2. Outlines of Product................................................................ 7
2. 1 Features................................................................................................................ 7
2. 2 How to Order ...................................................................................................... 7
2. 3 Structure of the product ................................................................................ 8
2. 4 Procedure （How to start the actuator) ................................................... 9
(1) Checking the content of the package ................................................ 9
(2) Mounting the unit ....................................................................................... 9
(3) Initial setting of the connect controller ............................................. 9
(4) Setting the unit........................................................................................... 9
(5) Unit wiring / Connection ......................................................................... 9
(6) Power supply ............................................................................................. 10
(7) Operation .................................................................................................... 10

3. Specifications .............................................................................11
3. 1 Specifications.................................................................................................... 11
3. 2 Details of parts................................................................................................. 13
3.3 Outside dimension diagram............................................................................ 14
(1) Screw mount type (LEC－GEＮ1) ...................................................... 14
(2) DIN rail mount type (LEC－GEＮ1D)................................................. 14
3.4 How to install...................................................................................................... 15
(1) How to install............................................................................................. 15
(2) Installation location ................................................................................. 15

4. Initial Setting ...............................................................................16

4. 1 Gateway unit Communication speed switch (B RATE) .................. 16
4. 2 Setting the switch to change the communication （CN2SW）......... 16
4. 3 Setting of controller (LEC)........................................................................... 17
4. 4 Setting of EtherNet/IP using RSLogix5000TM..................................... 20

5. External connection .................................................................21

5. 1 CN4: Power supply connector .................................................................... 21
5. 2 CN3: Bus connector ....................................................................................... 21
5. 3 CN1: CONT connector................................................................................... 21
5. 4 CN2: PC/TB connector................................................................................. 22

6. CN4: Power supply connector .............................................23

-1-
 6.1 Power supply connector................................................................................. 23
6.2 Power line ............................................................................................................ 23
6. 3 Wiring of the shutdown circuit .................................................................... 24
【Shutdown circuit Example】 ...................................................................... 26

7. CN1: Controller IF communication connector (CONT)27

7. 1 Connection......................................................................................................... 27
7. 2 Wiring diagram................................................................................................... 29

8. CN2: TB/PC connector..........................................................30

8. 1 How to use......................................................................................................... 30

9. LED display ..................................................................................31

9. 1 LED display ........................................................................................................ 31
9. 2 Controller IF communication status and LED display ........................ 32

10. Mode.............................................................................................33
10. 1 Outline............................................................................................................... 33
10. 2 Step data input mode .................................................................................. 33
10. 3 Numerical data input mode ........................................................................ 33
10. 4 Data writing mode ......................................................................................... 35

11. Memory map .............................................................................36

11.1 Memory assignment ....................................................................................... 36
11.2 Controller IF flag（IN Data） ......................................................................... 40
11.3 Gateway unit status flag（IN Data） .......................................................... 40
11.4 Gateway unit control flag（OUT Data）.................................................... 42

12. Precautions for controlling the controller (LEC).......43

12. 1 Communication delay between the gateway unit unit and the controller(LEC) 43
12. 2. Guideline of the Response delay between the Gateway and the Motor Control Unit
........................................................................................................................................ 44

13. Wiring of cables/Common precautions..........................45

14. Electric actuators/Common precautions .....................46

14.1 Design and selection ..................................................................................... 46
14.2 Mounting............................................................................................................. 47
14.3 Handling.............................................................................................................. 48
14.4. Operating environment ................................................................................ 49
14.5 Maintenance ..................................................................................................... 50
14.6 Precautions for actuator with lock........................................................... 50
-2-
15. Gateway unit and its peripheral devices /Specific product precautions 51
15.1 Design and selection ..................................................................................... 51
15.2 Handling.............................................................................................................. 51
15.3 Mounting............................................................................................................. 52
15.4 Electrical wiring ............................................................................................... 53
15.5 Power supply .................................................................................................... 53
15.6. Grounding.......................................................................................................... 53
15.7 Maintenace........................................................................................................ 54

-3-
 LEC Series/ Gateway unit
1. Safety Instructions

These safety instructions are intended to prevent hazardous situations and/or equipment damage. These
instructions are categorized into three groups, "Caution", "Warning" and "Danger" depending on the level of
hazard and damage, and the degree of emergency. They are all important notes for safety and must be
followed in addition to International Standards (ISO/IEC), Japan Industrial Standards (JIS)*1) and
other safety regulations*2).
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems
ISO 4413: Hydraulic fluid power -- General rules relating to systems
IEC 60204-1: Safety of machinery -- Electrical equipment of machines (Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots -- Safety
JIS B 8370: Pneumatic fluid power - General rules relating to systems
JIS B 8361: Hydraulic fluid power - General rules relating to systems
JIS B 9960-1: Safety of machinery - Electrical equipments of machines (Part 1: General requirements)
JIS B 8433-1993: Manipulating industrial robots - Safety, etc/
*2) Labor Safety and Sanitation Law, etc.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or
Caution moderate injury.
Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or
Warning serious injury.

Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or
serious injury.

Warning
(1) The compatibility of the product is the responsibility of the person who designs the
equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with
specific equipment must be decided by the person who designs the equipment or decides its
specifications based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the
person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest
catalog information, with a view to giving due consideration to any possibility of equipment failure
when configuring the equipment.
(2) Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment must be performed by an
operator who is appropriately trained and experienced.
(3) Do not service or attempt to remove product and machinery/equipment until safety is
confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after measures
to prevent dropping of driven objects or run-away of machinery/equipment have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the
specific product precautions of all relevant products carefully.
3.Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.

-4-
 Warning
(4) Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a location
exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space,
shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact
with food and beverages, emergency stop circuits, clutch and brake circuits in press applications,
safety equipment or other applications unsuitable for the standard specifications described in the
product catalog.
3. An application which could have negative effects on people, property, or animals requiring special
safety analysis.
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using
a mechanical protective function, and periodical checks to confirm proper operation. Check the
product regularly in order to confirm normal operation.

-5-
 LEC-G Series/Gateway unit
Safety Instructions

Caution
The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.

Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before using the product.

[Limited warranty and Disclaimer]

(1) The warranty period of the product is 1 year in service or within 1.5 years after the product is
delivered.
Also, the product may have specified durability, running distance or replacement parts. Please
consult your nearest sales branch.

(2) For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to SMC product independently, and not to any other damage
incurred due to the failure of the product.

(3) Prior to using SMC products, please read and understand the warranty terms and disclaimers
noted in the specified catalog for the particular products.

[Compliance Requirements]
When the product is exported, strictly follow the laws required by the Ministry of Economy, Trade and
Industry (Foreign Exchange and Foreign Trade Control Law).

-6-
2. Outlines of Product
2. 1 Features
The gateway unit (GW unit, hereafter) is the unit to connect the electric actuator controller (LEC
series) to Ethernet IP. One unit can control up to 12 same type of controllers.

Caution
When setting up the device or when failure occurs, please refer to the operation manual of the
controller, the actuator, and the teaching box as well as this operation manual.
* Keep this operation manual accessible so it can be referred to when necessary.

2. 2 How to Order
How to order is shown below.

Ｌ Ｅ Ｃ -Ｇ Ｅ Ｎ １ □
DIN rail
Electric equipment
Controller Nil Not mountable.
D Mountable

Applicable

EN1 EtherNetIP

Unit types
G Gateway unit

-7-
2. 3 Structure of the product

The system applies this unit consists of the unit below.

System structure drawing.

PLC
Teaching box
LEC-T1-３□G□
HUB
EtherNet/IP
●Controller setting Kit
Gateway unit LEC-W2
LEC-GEN1□

LEC serial communication (RS485)

Modbus communication Termination
Resistor

Motor controller
LEC Series ・

Electric actuator
LE Series

-8-
2. 4 Procedure （How to start the actuator)
Install, wire, set and operate the gateway unit referring to the procedure below when the product is
used for the first time.

(1) Checking the content of the package

After unpacking, check the description of the label to identify the gateway unit and the quantity of
accessories. Gateway unit

Part’s name Quantity Power rsupply connector

Gateway unit 1 pc.

（LEC－GEN1）
Power supply connector 1 pc.

(*)
These items are included if you ordered by the part number for a set of controller and actuator.

(2) Mounting the unit

Refer to 3.4 How to install for the mounting of the gateway unit.

(3) Initial setting of the connect controller

The parameters of the controller’s, that are is connected to the gateway unit need to be set.
Refer to section 4. 3 Setting of controller (LEC)

(4) Setting the unit

It is necessary to set the node address and the communication speed by the rotary switch of the
gateway unit. Refer to section 4. Initial Setting

(5) Unit wiring / Connection

Connect cables to the connectors(CN1 to CN3) of the gateway unit.
Refer to section 5. External connection for the wiring of connectors.

Connector

-9-
(6) Power supply
Supply power 24V DC.

Caution
Supply power first to the controller (LEC), then to the gateway unit.
If power is supplied to the gateway unit and then to the controller (LEC), reset the data link after
supplying power to the controller (LEC).
(Refer to 11.4 Gateway unit control flag for the details of data link reset.)

If the condition is normal, LED on the front of the gateway unit turns on as the table below when power
is supplied.

Functions LED Condition

condition

PWR Green On Supply of power

CN2 STAT Off CN2（TB/PC terminal） invalid
BUS STAT Green Controller IF is communicating
flashing
ALM Green No alarm
flashing
NS Green On EtherNetIP status normal
MS Green On EtherNetIP status normal

Refer to 10. LED display for the explanation of LED lamps.

If LED [ALM] on the front panel of the gateway unit shows red, an alarm conditions has occured.

(7) Operation
Refer to section 11. Memory map for the assignment of the memory. Read the operation manual of
LEC series as well.

- 10 -
3. Specifications
3. 1 Specifications
Basic specifications of the product.
Item Specifications
Rated voltage 24 VDC±10%
Current consumption 200mA or less (When teaching box is not connected)
300mA or less (When teaching box is connected)
Applicable controller Electric actuator controller (LEC series)
Product to be connected Max. 12pcs.
When conformity to UL is required, the electric actuator and controller should be used with a UL1310
Class 2 power supply.

【EtherNet type】
Item Specifications
Fieldbus EtherNet (IEEEE802.3)
Media 100BASE-TX
Communication speed 10/100Mbps (Automatically selected)
Maximum length of cable 100m (328ｆｔ)
Fieldbus protocol EtherNet/IP TM
Occupied area (inputs /outputs) 2048 point（256byte）/2048 point（256byte）
IP address setting DHCP server. Arbitrary address
Device information Vendor ID: 7
Device type: 0 (Generic device)
Product code: 154
Product name: LEC-GEN1

- 11 -
【Controller IF communication spec.】
Item Specifications
Serial RS485 (Modbus protocol compliant)
communication
Communication 115.2k or 230.4kbps (Select 115.2kbps when the teaching box is connected)
speed
Cable length The cable for the teaching box (3m) and the electric actuator controller (5m x
12)
makes 63m of cable length. This is the maximum cable length.

･･･
3m
5m 5m 5m 5m

【Conditions of environment】
Item Specifications
Applicable ambient temperature 0～40℃(No freezing)
Applicable ambient humidity 90%RH or less (No condensation)
Atmosphere No corrosive gas, flammable gas, oil mist, or particles.
Storage temperature -10～60℃(No freezing)
Storage humidity 90%RH or less (No condensation)
Vibration 4.9m/s2 (0.5G) or less
Enclosure IP20
200g (screw mount type)
Mass
220g (DIN rail mount type)

- 12 -
3. 2 Details of parts
Details of parts of the gateway unit

(2)
(3)
①
(4)

(5)

(6)

(7)

No. Display Description Detail

1 - LED lamp LED to indicate the condition of the gateway unit

Communication The switch to set the communication speed of the
2 B RATE
speed controller IF communication line.
Disables the communication with the controller IF
Communication
3 CN2 SW communication line, and ables the communication with the
switch
equipment which are connected to CN2.
Power supply
4 CN4 Connect the power supply and EMG signal.
connector
5 CN3 Bus connector Connect EtherNet/IP line.
The connector which connect LEC teaching box (LEC-T1)
6 CN2 TB/PC connector
or the ACT software Controller for setting (LEC-W2)
The connector for the controller IF communication line.
7 CN1 CONT connector
Connect the motor controller (LEC series).

- 13 -
3.3 Outside dimension diagram
The outside view of this product is as shown in the diagram below:
(1) Screw mount type (LEC－GEＮ1)

(2) DIN rail mount type (LEC－GEＮ1D)

- 14 -
3.4 How to install
(1) How to install
There are two types of controllers; screw mount type and DIN rail mount type.
The followings are the descriptions on how to install each type:

[1] Screw mount type (LEC-GEN1) [2] DIN rail mount type (LEC-GEN1D)
(Installation with two M4 screws) (Installation with the DIN rail)
DIN rail is locked.

Screw direction

DIN rail

Screw direction

Hook the controller on the DIN rail and

press the lever of section A in the arrow
direction to lockit.

(2) Installation location

Please install this gateway unit at an appropriate place where the surrounding temperature will
not exceed 40oC.

Caution
Install the gateway unit on a flat surface. Excessive pressure applied to the housing will damage the
gateway unit.

- 15 -
4. Initial Setting
4. 1 Gateway unit Communication speed switch (B RATE)
The transmission rate of motor controller LEC are set. Table below shows the setting of switches.

The treble is shown about the transmission rate

of controller IF

Communication speed of
B RATE
controller IF
F
: Not used
9
8 230.4 kbps
7
: Not used
1
0 115.2 kbps

※ Do not set B RATE to the value of "Unused"

Caution1: Set the controller IF communication speed at 115.2kbps to use the teaching box (LEC-T1-□).
Caution2: Turn off the power supply in order to change the switch setting

4. 2 Setting the switch to change the communication （CN2SW）

Turn ON the communication switch (CN2SW) during EtherNet/IP control. If the communication
switch (CN2SW) is turned off during EtherNet/IP control, communication error (data link error) is
generated in the gateway unit. Turn OFF communication switch (CN2SW) when changing the setting
of controller (LEC) by connecting the teaching box (LEC-T1-□) of setting software (LEC-W2) to PC/TB
connector (CN2). In this case, the communication from EtherNet/IP to the controller (LEC) is cut.

- 16 -
4. 3 Setting of controller (LEC)
Initial parameter setting is necessary for the controller (LEC) which is connected to the gateway unit.
Set the following by directly connecting the teaching box (LEC-T1-□) or the setting software to the
controller (LEC) before connecting the gateway unit.
Check the operation manual of the controller (LEC) and the teaching box (LEC-T1-□) when setting
the controller (LEC).

4. 3. 1 ID setting
ID setting is necessary when connecting two or more controllers (LEC) to the gateway unit.
Assign ID to each controller (LEC) in serial number so that the numbers do not overlap. The setting
range of ID is between 1 to 12.

[Example of ID change procedure using the ACT Controller Setting software (LEC-W2)]
Start the setting software in Normal mode.
Open the parameter window.
(1) Set the controller ID.
(Letters are changed to blue)

(2) Select Download.

（Changed ID is sent to the controller. ID
set value turns to black）

4. 3. 2 Setting of the communication speed

It is necessary to match the gateway unit controller IF communication speed with the controller (LEC)
communication speed. Set the controller IF communication speed at 115,2kbps to use the teaching
box (LEC-T1-□)

[Communication speed change procedure Setting software (LEC-W2)]

Start the setting software with Normal mode.
(1)Select [HELP] - [Password] from the menu. Password input screen below appears. Enter "password".

- 17 -
(2) Set the controller so that the communication speed can be changed.
Change "Parameter protect" setting so that "Communication speed" parameter can be changed.
View the parameters of the controller.

(2)-1 Change parameter protect

to [3: Common + Extend + Step].

(2)-2 Select Download.

Select "Basic" Tab - Item "Parameter protect" to "3: Common + Extend + Step"
The changed data is sent by clicking the download button, and the parameter protect set value text
changes from blue to black.
(3) Select the "Motor" Tab of the parameter window to change item "Comm speed" to "115200" for when
using Teaching box or "230400" for when using ACT Controller software.

(3)-1 Select the tag "Motor".

(3)-2 Change the communication speed

to 「115200」(5) or 「230400」(6)

(3)-3 Select Download.

The changed data is sent by clicking the download button, and "Communication speed" set value is
changed from blue to black.

- 18 -
(4) Change item "Parameter protect" using “Basic” tab of the display of (2) to "1: Common + Step data"
and click download.
(5) Close the ACT Controller software (LEC-W2) and turn OFF the controller (LEC) power supply. The
changed communication speed will be valid from the next time the controller (LEC) is turned on.

Caution
The communication speed of the gateway unit and the controller (LEC) must match.
If the communication speed does not match, the gateway unit and the controller (LEC) cannot
communicate.
Set the controller IF communication speed to 115,2kbps when using the teaching box (LEC-T1-)
The defaults setting of communication speed in the setting software (LEC-W2) is 38.6kbps.
After changing the communication speed, set the ACT Controller software (LEC-W2)
communication speed to 115.2kbps for Teaching box or 230.4kbps for the ACT controller software.
Do not change any parameters other than "ID setting"/"Communication speed setting".
Otherwise, malfunction can result.
Change "ID setting" / "Communication speed setting" to use the controller (LEC) stand-alone.

- 19 -
4. 4 Setting of EtherNet/IP using RSLogix5000TM

It is necessary to enter the value of Assembly instance Input，Output，and Configuration to set by

using RSLogix5000TM. Set with values below.

・Comm Format: Data-SINT

・Comnection Parameters
Instance Size
Input 100 256
Output 150 256
Configuration 1 0

＊It is not necessary to set Connection and ModuleInfo.

＊RSLogix5000TM is a registered trademark of Rockwell Automation.

- 20 -
5. External connection
5. 1 CN4: Power supply connector
Connect the power supply. The gateway unit and the controller (LEC) should have the common 0V line.

Gateway
Unit
Power supply
（24 VDC）
Power supply line
CN４

（Cables, PLC and power supply are prepared by customer)

* Refer to 6. CN4: Power supply connector

5. 2 CN3: Bus connector

Connect the EtherNet line and the controller (LEC) with the communication cable (LEC-CG□-□)

Gateway
Unit
PLC
EtherNet line.

CN３ HUB

（ Cables, PLC and power supply are prepared by

5. 3 CN1: CONT connector

Connect the gateway unit and the controller (LEC) to communication cable (LEC-CG□-□).

Gateway Controller input power supply

unit 24 VDC

CN１
Terminating Resistor
(120Ω 1/4W)

CN4 CN4 CN4

Controller (LEC) Controller (LEC) Controller (LEC)

- 21 -
 * Refer to section 7. CN1: Controller IF communication connector (CONT)

Caution
Do not pull out the cable between the gateway unit and the cable, or cut off the power
supply to the controller (LEC). Communication is interrupted.

5. 4 CN2: PC/TB connector

The connector which connects the tools teaching box (LEC-T1-3*G*) or PC (LEC-W2) for setting the
controller (LEC.
The data link of the gateway unit and the controller (LEC) data is cut by turning off CN2SW or
stopping data link, and communication with the tool teaching box (LEC-T1-3*G*) for setting the controller
or PC (LEC-W2) becomes possible.

(1) Connecting the teaching box

Gateway unit

CN2 Teaching box

（with 3m of cable）

(2) Connecting PC

●Controller setting software

（Communication cable, USB cable, conversion unit）

Gateway unit
Conversion unit モニタ
現在 位 置 120.3 mm 動 作中

現在 速 度 200 mm/s アラーム

USB cable
設定 位置 速度

1 ﾃ ｽﾄ 100 500
2 ﾃ ｽﾄ 200 1000

（A-miniB type）
3 ﾃ ｽﾄ 50 200

CN2CN２
Communication cable
PC

（PC is prepared by customer)

※Refer to 8．CN2：TB/PC Power supply connector for usage.

Caution
Do not start the setting software during data link.
Otherwise, communication error (data link error) is generated with the gateway unit.

- 22 -
6. CN4: Power supply connector
6.1 Power supply connector
Specifications of the communication connector in accessory

terminal Function Functional explanation

1 EMG + EMG signal output ＋ Output terminal of the emergency stop

2 EMG - EMG signal output - switch of the teaching box.

3 C 24V Power supply + terminal Power supply terminal of the Gateway unit

4 0V (Power to the teaching box is supplied from

5 4 3 2 1 Power supply - Terminal
this terminal)

5 FG FG Terminal Grounding terminal

Caution
(1) 0V line of the gateway unit and the motor controller (LEC) have to be common.
(2) When conformity to UL is required, the electric actuator and controller should be used with a
UL1310 Class 2 power supply.

6.2 Power line

（Power lines are prepared by customer. Specifications below need to be satisfied)
Item Specifications
Applicable Power terminal AWG20: Single line,No insulation sleeve, Twisted wire with
wire (24V，0V) bar terminal.
Size *The rated temperature for the insulation coating: 60
degrees C or more.
EMG signal output AWG20: Single line,No insulation sleeve, Twisted wire with
（EMG+,EMG-） bar terminal.
*Rated temperature of the insulation cover is 60 degrees C
or higher

Peeled wire
length
8mm

Caution
Do not connect multiple wires to one terminal.

- 23 -
 Caution
(1) The earthling should be the dedicated grounding point. It should be a functional ground with less
than 100 Ω resistance.
(2) The ground point should be near this gateway unit to make the wire length shorter.

Gateway unit Other device Gateway unit Other device

Recommended Functional grounding Not Recommended grounding

6. 3 Wiring of the shutdown circuit

The gateway unit has terminals (EMG+, EMG-) which route the stop switch signal’s from the teaching
box when the communication switch (CN2SW) is turned on. Set the terminal to EMG terminal of the
controller (LEC) when using the teaching box.

Switch to change
the communication
（CN2SW）

Teaching Shutdown
RY
box circuit
CN4
CN2
EMG +

EMG-

24V
Internal
circuit
0V

Gateway unit

- 24 -
 Caution
Turn on the communication switch (CN2SW) before install / removal of the teaching box to
/ from the gateway unit.
If EMG+ and EMG- terminals are connected to the controller (LEC) or a shutdown circuit and the
communication switch is turned off when the teaching box is not connected, connected controller
(LEC) or the shutdown circuit receives stop signal (Open between EMG+ and EMG-) and operation
stops

- 25 -
【Shutdown circuit Example】
Shutdown circuit with gateway Check the circuit referring the controller (LEC) operation manual.

【Example of the circuit】ex. LEC6

DC24 0V
Shutdown is lifted
Switch Ry

Stop
Switch
Gateway
EMG + Surge suppressor
Ry
Unit
EMG -

Power supply plug (1st. unit)

BK RLS
EMG
Ry
C 24V
M 24V 24V Controller
0V 0V input power

Power supply plug (2nd. unit)

BK RLS
EMG
Ry
C 24V
M 24V 24V Controller
0V 0V input power

Power supply plug (3rd. unit)

BK RLS
EMG
Ry
C 24V
M 24V 24V Controller
0V 0V input power

Caution
When the stop signal is input, the controller (LEC) is stopped with max deceleration speed, and servo
motor is turned off.

- 26 -
 7. CN1: Controller IF communication connector (CONT)
7. 1 Connection
One unit can control up to 12 pcs. of controllers (LEC).
The example of link connection which consists of telecommunication cable LEC-CG 1-1 and cable
LEC-CG 2-1 between branches is shown below.
3 LEC-CG2-□
b) M12 4pin b) M12 4pin
male connector male connector

2 LEC-CGD 2 LEC-CGD 4
5

c) M12 4pin
female connector
1 LEC-CG1-□
b) M12 4pin b) M12 4pin
male connector male connector

a) RJ45 male connector with a shield（8P）

1 LEC-CG1-□ 1 LEC-CG1-□

a) RJ45 male connector with a shield（8P） a) RJ45 male connector with a shield（8P）

No Description Part number Content

1 Communication cable cable LEC-CG1-□ Cable to connect the gateway unit CN1 and the branch

K 0.3m connector, or controller (LEC) CN4 and the branch connector.

L 0.5m
1 1m

2 Branch connector LEC-CGD The junction cable to connect the gateway and the controller.

3 Cable between branches LEC-CG2-□ Cable to connect the branch connector.

K 0.3m
L 0.5m
1 1m

4 Terminating Resistor Termination on RS-485 Bus (120 Ohms)

Recommended connector

:XS2C-D4** [OMRON Corporation]

120Ω 1/4W

5 RJ-45 connector dust cover Dust adhere when the RJ-45 connector is not connected with the

CN1 or CN2 or CN3 connector.

LEC-CAP-X22
Please attach a cover when you prevent the adhesion such as

dust.

- 27 -
Recommended connector
No Description Part number
a) RJ45 male connector with a shield（8P） TM21P-88P ［HIROSE ELECTRIC CO., LTD.］
b) M12 4pinmale connector HR24-8DJ4PE550A(73) ［HIROSE ELECTRIC CO., LTD.］
XS2G-D4** [OMRON Corporation]
c) M12 4pin female connector HR24-8DP4S300(73) ［HIROSE ELECTRIC CO., LTD.］
XS2C-D4** [OMRON Corporation]

- 28 -
7. 2 Wiring diagram

For you reference, the example of wiring of the gateway unit CN1 is shown below.
The communication line from the gateway unit CN1 branches to each controller (LEC) by the branch
connector. It is recommended to connect the terminating resistor (120Ω 1/4W) to the branch connector
at the terminal.
When connecting the cable, the shield of the cable becomes same potential as 0V of the controller
power supply.
When using it, do not contact it to conductive parts of switchboard, other instruments, wiring, etc.

← Gateway unit CN1

Description Pin No.
N.C. 1 Branch Branch

N.C. 2 1 1 1 1
SD+ 3 2 2 2 2
SD- 4 3 3 3 3
N.C. 5 4 4 4 4
N.C. 6
N.C. 7 1 2 3 4 1 2 3 4
N.C. 8
Shield

←Controller CN4 ←Controller CN4

Description Pin No. Description Pin No.
EMG+ 1 EMG+ 1
EMG- 2 EMG- 2
SD+ 3 SD+ 3
SD- 4 SD- 4
EN_SW+ 5 EN_SW+ 5
ON 6 ON 6
DC24V 7 DC24V 7
GND 8 GND 8
Shield Shield

- 29 -
8. CN2: TB/PC connector
8. 1 How to use
This connector is for setting the controller (LEC) which is connected to the gateway unit by the teaching
box or the set software.
When the communication switch (CN2SW) is turned off, the communication from EtherNet/IP to the
controller is disconnected, and the signal line of CN2 and CN1 is connected. From now on, the setting of
each controller is possible.

The following is the setting procedure of the controller (LEC) when the teaching box or PC setting
software us connected to the gateway unit.

【Procedure to start setting】

(1) Connect the teaching box or PC to CN2 of gateway unit.
(2) Turn off the communication switch (CN2SW).
(3) Reset signal is sent to all controllers (LEC) which are connected to the gateway unit, and the
communication from Ethernet to the controller (LEC) is disconnected. Reset signal stops all actuators.
(4) Communication from the teaching box or PC becomes available.

【Procedure to finish setting】

(1) Exit the Act Controller software.
(2) Turn on the communication switch (CN2SW).
(In case of the teaching box, power supply is turned off at this point)
(3) Communication starts after the reset signal is sent from the gateway unit to the controller (LEC).
Reset signal stops all the actuators immediately after communication starts.
(4) Remove the teaching box or PC from the CN2 of gateway unit.

Caution
Do not start the setting software during data link (CN2SW turn on).
Otherwise, communication error (data link error) is generated with the gateway unit.

Use the teaching box and the setting software after ｆinishing startup process of the gateway
unit (After ALM lamp green blinks). (CN2SW turn off etc.）
The gateway unit communicates with controller (LEC) as startup processing immediately
after turning on of the power supply.
At this time, if the teaching box or the setting software communicate to controller (LEC),
communication error is generated.

- 30 -
9. LED display
9. 1 LED display

LED name Content

PWR OFF Power is not supplied
Power supply status
Green ON Power is supplied
CN2STAT ON, OFF status of OFF When switch ON
SN2SW Green ON When switch OFF

BUS Green flashing Communicating

STAT Controller IF status OFF Communication
disconnected
Green flashing Normal status
ALM Orange Warning generated
flashing
Red ON When alarm is
Alarm status.
generated or
communication data
link is disconnected.
MS Module Status OFF No power
(Ethernet IP) Green ON Controlled by a
Scanner in Run state
Green flashing Not configured,or
Scanner in Idle state
Red ON Major fault
Red,flashing Recoverable fault
NS Network Status OFF No power or no IP
(Ethernet IP) address
Green ON On-line,connections
established
Green,flashing On-line,no
connections
established
Red ON Duplicate IP address
Red,flashing Connections timed out

- 31 -
9. 2 Controller IF communication status and LED display

Gateway unit status PWR BUS STAT ALM CN2 STAT

Supply of power Green On Off Off Off
Controller (LEC) and normal Green On Green Green Off
communication flashing flashing
Command to interrupt data link is being Green On Off Green Off
given flashing
CN2SW OFF Command to interrupt Green On Off Green Green On
data link is being given flashing
Contr Communication error with Green On Green Orange Off
oller some controllers (LEC) is flashing flashes
IF detected.
Communication error is Green On Green Red On Off
detected for all controllers flashing
(LEC), or IF communication
speed of the controller is
incorrect.

- 32 -
10. Mode
10. 1 Outline
This unit has 3 types of operation mode. These modes can be switched by mode change[OUT: 250.0,
250.1] Current mode can be checked by mode return[IN: 250.0, 250.1]
Refer to “11.4(1) Return of the mode” for “Return of the Mode”.

●Step data input mode [250.0=0，250.1=0]

Operating actuator by using the memory of the gateway unit which corresponds to parallel IO of
controller (LEC).
●Numerical data input mode [250.0=1，250.1=0]
Operating actuator by using the memory of the gateway unit which corresponds to parallel IO of
controller (LEC), and operating actuator by directly sending the parameters which like a position, a
speed etc., are available.
●Step data writing mode [250.0=0，250.1=1]
Operating actuator by using the memory of the gateway unit which corresponds to parallel IO of
controller (LEC), and editing step data of the LEC controllers through the gateway unit, are available.

Please confirm the setting method of "Mode change" and "Mode return" by "Gateway control flag" and
"Gateway unit state flag".

10. 2 Step data input mode

This is the mode that Operating actuator by using the memory of the gateway unit which corresponds
to parallel IO of controller (LEC).
In case that “ID” setting of the controller(LEC) is “1”, the memory which corresponds to the parallel IO
of controller can be operated by [OUT: 0][OUT: 1] and [IN: 0][IN: 1]
Refer to the manual of controller (LEC) for detail of the function and the operation of parallel IO.

10. 3 Numerical data input mode

This is the mode that operating actuator by sending to controller (LEC) the data which is a position, a
speed etc.
The actuator moves with the position, the speed etc which is specified by sent data.
In this mode, the command by using parallel I/O is available.
Before operating the actuator by directly sending the data which like a position, a speed etc, SVON and
return to origin should be finished.
Please make same operation as performing SVON and return to origin with parallel IO by using the
corresponding memory.
And operating the actuator is availavle by using the memory which corresponds to parallel IO of LEC
controller.
Refer to the manual of controller (LEC) for detail of the function and the operation of parallel IO.
The data such as the current position can be read by “Setting numerical data”.
Refer to “11.4(5) Setting numerical data” for “Setting numerical data”.

- 33 -
●Operation commanded by numerical data input mode (ID=1)

(1) Write “0” in [OUT: 2].

(2) Write the motion profile (position, speed…) in [OUT: 3～19]
Refer to "7.1 Step data" of the operation manual of the controller(LEC).
(3) Write “1” in [OUT: 2]. Then, the command of the driving is sent to the controller (LEC).
(4) When the sending to the controller(LEC) is completed, “Sending completed” [IN: 19.0] changes
from “0” to “1” and the actuator starts driving.
(5) And, when the actuator completes driving, INP [IN: 1.3] is changed from “0” to “1”.
Refer to "6.3 Parallel IO input" of the operation manual of the controller(LEC) for detail of INP
signal.
(6) Write “0” in [OUT: 2].
Then, “Sending completed” [IN: 19.0] is changed from “1” to “0”.

1 3 6
Operation command [OUT: 2]

2
Data (Position, speed) [OUT: 3～19]）

4
Sending [IN: 19.1]

(6) Sending completed [IN: 19.0]

Operation
5

INP [IN: 1.3]

- 34 -
10. 4 Data writing mode

This is the mode that the step data of the controller(LEC) can be changed through the gateway unit.
After changing it, the changed step data is reflected by commanding to drive the changed step data.
And the same functions as step data input mode are available in this mode.
The driving and the return to origin etc. are commanded by using the memory which corresponds to
parallel IO of LEC controller.
Refer to the manual of controller (LEC) for detail of the function and the operation of parallel IO.

●Writing step data method

(1)Write “0” in [OUT: 3].
(2)Write the motion profile (position, speed…) in [OUT: 4-19]
Refer to "7.1 Step data" of the operation manual of the controller(LEC).
(3)Write the step data number which is changed in [OUT: 2]. (range 0-63 of input)
(4)Write “1” in [OUT: 3]. Then, the data which is written in avobe (2) are sent to the controller(LEC).
(5)When the sending to the controller(LEC6) is completed, “Sending completed” [IN: 19.0] is
changed from “0” to “1”.
(6)Write “0” in [OUT: 3].
Then, “Sending completed ” [IN: 19.0]changes from “1” to “0”.

- 35 -
11. Memory map
11.1 Memory assignment

● Gateway unit --> Higher level device [IN]

Corresponding Bit/Byte Data Model/ Corresponding

Address Value range Unit
ID No. name Size mode
0 OUT0 bit 0,1 -
1 OUT1 bit 0,1 -
2 OUT2 bit 0,1 -
3 OUT3 bit 0,1 -
0
4 OUT4 bit 0,1 -
5 OUT5 bit 0,1 -
6 - bit 0 -
7 - bit 0 -
All modes
0 BUSY bit 0,1 -
1 SVRE bit 0,1 -
2 SETON bit 0,1 -
3 INP bit 0,1 -
1
4 AREA bit 0,1 -
5 WAREA bit 0,1 -
ID1 6 ESTOP bit 0,1 -
7 ALARM bit 0,1 -

2 3

3 2 Current
4 +/-2147483647 0.01mm
position
4 1
5 0
6 H Current Numerical data
2 0 to 65500 mm/s
7 L speed input
8 H Current
2 0 to 300 %
9 L Force
10 3
11 2 Target
4 +/-2147483647 0.01mm
12 1 position
13 0

・Please refer the operation manual of the step motor controller (LECP6) and the servo motor controller
(LECA6) to check the detail of each signal.

- 36 -
Corresp
Bit/Byte Model/ Corresponding
onding Address Data name Value range Unit
No. Size mode
ID
14 - Alarm 0 to 255 -

15 - Alarm 0 to 255 - Numerical data

4
16 - Alarm 0 to 255 - input
ID1
17 - Alarm 0 to 255 -

18
Controller IF status flag(ID=1) All modes
19
ID2 20 to 39 Same as ID1
ID3 40 to 59 Same as ID1
ID4 60 to 79 Same as ID1
ID5 80 to 99 Same as ID1
ID6 100 to 119 Same as ID1
ID7 120 to 139 Same as ID1
ID8 140 to 159 Same as ID1
ID9 160 to 179 Same as ID1
ID10 180 to 199 Same as ID1
ID11 200 to 219 Same as ID1
ID12 220 to 239 Same as ID1
- 240 to 249 Unused
- 250 to 253 Gateway unit status flag All modes
- 254,255 Unused

- 37 -
● Higher level device --> Gateway unit [OUT]

Corresp
Bit/Byte Model/ Corresponding
onding Address Data name Value range Unit
No. Size mode
ID
0 IN0 bit 0,1 -
1 IN1 bit 0,1 -
2 IN2 bit 0,1 -
3 IN3 bit 0,1 -
0
4 IN4 bit 0,1 -
5 IN5 bit 0,1 -
6 - bit 0 -
7 - bit 0 -
All mode
0 HOLD bit 0,1 -
1 SVON bit 0,1 -
2 DRIVE bit 0,1 -
3 RESET bit 0,1 -
1
4 SETUP bit 0,1 -
5 - bit 0 -
6 - bit 0 -
7 - bit 0 -
ID1 0: no send Numerical data
Start flag
2 - 1 1: send - input
Step data No 0 to 63 Data writing
1: Absolute
2: Relative
3 - Operation 1 -
0: (Only data
writing mode)
4 H
Speed 2 0 to 65500 mm/s
5 L Numerical data
6 3 input
7 2
Position 4 +/-2147483647 0.01mm
8 1 Data writing
9 0
10 H
Acceleration 2 0 to 65500 mm/s2
11 L
12 H
Deceleration 2 0 to 65500 mm/s2
13 L

・Please refer the operation manual of the step motor controller (LECP6) and the servo motor controller
(LECA6) to check the detail of each signal.

- 38 -
Corresp
Bit/Byte Model/ Corresponding
onding Address Data name Value range Unit
No. Size mode
ID
14 - Pushing force 1 0 to 30 10%

15 - Trigger LV 1 0 to 30 10%

Pushing Numerical data

16 - 1 0 to 255 mm/s
ID1 speed input
Positioning Data writing
17 - 1 0 to 30 10%
thrust
18 H
In pos 2 0 to 65500 0.01mm
19 L
ID2 20 to 39 Same as ID1
ID3 40 to 59 Same as ID1
ID4 60 to 79 Same as ID1
ID5 80 to 99 Same as ID1
ID6 100 to 119 Same as ID1
ID7 120 to 139 Same as ID1
ID8 140 to 159 Same as ID1
ID9 160 to 179 Same as ID1
ID10 180 to 199 Same as ID1
ID11 200 to 219 Same as ID1
ID12 220 to 239 Same as ID1
- 240 to 249 Unused
Step data input
mode
- 250 to 253 Gateway unit control flag
Numerical data
input
- 254,255 Unused

- 39 -
11.2 Controller IF flag（IN Data）

Controller IF flag is sent back to each ID ID=1 is shown below as an example

[ID=1]
bit
I_Address 7 6 5 4 3 2 1 0
－ － － － － － Abnormal
18 Connect station
station
－ － － － － － Sending
19 Sending
completed

(1) Connect station [IN18.0]

1(ON) appears when it is confirmed that the motor controller (LEC) is connected. 0 (OFF) appears
when the connection is not confirmed.

(2) Abnormal station [IN18.1]

0 (OFF) appears when the communication with the motor controller is normal at the connect station. 1
(ON) appears when the communication is not normal.

(3) Sending [IN: 19.0]

1 (ON) appears while the operation command from the motor controller (LEC) is given and the
sending of the operation data for the motor controller is completed at numerical data input mode. 0
(OFF) appears when the sending is completed.

(4) Sending completed [IN: 19.1]

1 (ON) appears when the sending of the operation command data to the motor controller (LEC) is
completed at the numerical data input mode. 1 (ON) appears while the sending of the operation
command data to the motor controller when the operation command is (ID=1). 0 (OFF) appears when
the sending is completed.

Start flag

Sending

Sending completed

Sending command

11.3 Gateway unit status flag（IN Data）

The flag to indicate the gateway communication status.

bit
I_Address 7 6 5 4 3 2 1 0
Commu
250 Initial ALARM READY － － Return of the mode
nicating
251
Return of the read numerical data
252
253 Return of the final station number

- 40 -
(1) Return of the mode
Current mode is displayed
Address250 Mode name
bit1 Bit0
0 0 Step data input mode
0 1 Numerical data input mode
1 0 Data writing mode

(2) READY
1 (ON) appears when the gateway is activated.

(3) ALARM
1 (ON) appears when one or more abnormal station are present, and the alarm is generated. 0 (OFF)
appears when alarm is not generated.

(4) Initial
0 (OFF) appears during processing the initial for check the connect station. 1 (ON) appears when the
processing of the initial is completed.

(5) During communication

1 (ON) appears when communication is made for one or more station. 0 (OFF) appears when not
communicated.
In one of following cases, communication is not made.
CN2SW is ON.
Stop［OUT：250.7］ is ON.
All the connect stations become abnormal and the communication is stopped.

(6) Return of the read numerical data (Valid only in numerical data input mode)
ON (1) appears in ID bit if numerical data can be read. OFF (0) appears when the data can not be read.
The command to read numerical data is given by [OUT: 251.]{OUT: 252.}.

bit
I_Address 7 6 5 4 3 2 1 0
251 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1
252 - - - - ID12 ID11 ID10 ID9

(7) Return of the final station number

Return the range of the ID of the controller to communication when the initial is processed. ID number is
returned in binary digit.
bit
ID 3 2 1 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
： ：
11 1 0 1 1
12 1 1 0 0

- 41 -
11.4 Gateway unit control flag（OUT Data）

The flag to control the gateway communication status.

bit
Address 7 6 5 4 3 2 1 0
250 Stop - Restart Reset - - Mode command
251 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1
252 - - - - ID12 ID11 ID10 ID9
253 - - - - Setting the final station number

(1) Mode command

Command the mode. Mode return[IN: 250.0.1.] is updated when the set mode becomes valid.

Address250 Mode name

bit1 Bit0
0 0 Step data input mode
0 1 Numerical data input mode
1 0 Data writing mode

(2) Reset
Communication to the abnormal station restart when 0 (OFF) is changed to 1 (ON). But, it is invalid
when Stop[OUT: 250.7.] is 1 (ON) or CN2SW is ON.

(3) Restart
Initial processing is executed again when 0 OFF) is changed to 1 (ON). But, it is invalid when Stop
[OUT: 250.7.] is 1 (ON) or CN2SW is ON.

(4) Stop
All communications to the connected motor controller (LEC) are stopped when 0 (OFF) is changed to 1
(ON). Communication restart by chancing to 0 (OFF) from 1 (ON).

(5) Setting numerical data (Valid only in direct setting mode)

ON (1) appears in ID bit if numerical data can be read. OFF (0) appears when the data can not be read.
bit
Address 7 6 5 4 3 2 1 0
251 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1
252 - - - - ID12 ID11 ID10 ID9

(6) Return of the final station number

Indicates the range of the ID of the controller(LEC) to communication when the initial is processed. ID
number is set in binary digit.
Input range is from 1 to 12. If the set value is lower than 0 or larger than 12, 12 is set.
bit
ID 3 2 1 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
： ：
11 1 0 1 1
12 1 1 0 0

- 42 -
12. Precautions for controlling the controller (LEC)
12. 1 Communication delay between the gateway unit unit and the controller(LEC)

There is communication delay between the gateway unit and the controller (LEC). Please refer to the
procedure below for the control procedure taking the delay into consideration
For details of each signal, please refer to the operation manual of each motor controller (LEC) to be
connected.

●Example of operation indication with step data input mode

Command Response (Output signal)
(Input signal)
(1) DRIVE input ON (1) ⇒ Confirm that all OUT0 to 5 in the
data information are changed to
OFF (0) from values before
DRIVE input ON (1).
(2) DRIVE input OFF (0) ⇒ Confirmed that OUT0 to 5 in the
data information is the value
within IN0 to 5 in specified data.
(3) INP is ON (1) and BUSY is OFF ⇒ Confirm the
(0) completion of the
operation.

Cautions for the above example

When the operation is ordered right after the operation shown below, the response of DRIVE above
are not recognized because OUT0 to 5 in the data information are all OFF (0) before turning ON (1) the
DRIVE input. In this case, take measures against the communication delay by using the timer.

【Condition in which OUT0 to 5 in the data information is all OFF】

- Supply of power
- During and the right after the returning to origin position.
- RESET input ON
- After DRIVE input OFF(0) after commanding to start step data No.0

- 43 -
12. 2. Guideline of the Response delay between the Gateway and the Motor Control Unit

The gateway unit communicates with the motor controller (LEC) to read the controller status and
commands the controller. The time for the communication causes delay in the response.
Please take this into consideration when selecting the PLC program.

Communication between the

gateway unit and the controller

PLC Gateway Motor controller

Unit （LEC）
EtherNet IP

Motor controller
（LEC）

Motor controller
（LEC）

Communication to read the motor controller status

The gateway unit communicates one by one in order. The communication time is approximately 30ms
per unit. When reading of numerical data is validated during Numerical data input mode or data rewrite
mode, it takes another 30ms for communicating with valid controller (LEC).

Communication for commanding the motor controller

When rewrite of the remote I/O and the register is commanded by Ethernet IP master, it takes 30ms
for communicating with the target controller (LEC).

Response delay depends on the number of the connected motor controllers (LEC) and rewrite
frequency.

Ex. 1) Response time guideline when four controllers are connected in step data input mode.
4 pcs. × approx. 30ms ＝ Approx. 120ms ＋ α
[α：Communication time to rewrite the remote I/O and the register]

Ex. 2) Response time guideline when twelve controllers are connected in step data input mode.
12 pcs. × approx. 30ms ＝ Approx. 360ms ＋ α
[α：Communication time to rewrite the remote I/O and the register]

Ex. 3) Response time guideline when 12 controllers are connected in numerical data input mode (6
controllers are valid for reading numerical data).
12 pcs. × approx. 30ms + 6pcs. x approx. 30ms ＝ Approx. 540ms ＋ α
[α：Communication time to rewrite the remote I/O and the register]

※This response time does not include the response time of Ethernet IP and motor controller (LEC), and
processing time of PLC.

- 44 -
13. Wiring of cables/Common precautions
Warning
1. Adjusting, mounting or wiring change should never be done before shutting off the power
supply to the product.
Electrical shock, malfunction and damaged can result.
2. Never disassemble the cable. Use only specified cables.
3. Never connect or disconnect the cable or connector with power on.
Caution
1. Wire the connector securely. Do not apply any voltage to the terminals other than those
specified in the product Manual.
2. Wire the connector securely.
Check for correct connector wiring and polarity.
3. Take appropriate measures against noise.
Noise in a signal line may cause malfunction. As a countermeasure, separate high voltage and low
voltage cables, and shorten wiring lengths, etc.
4. Do not route wires and cables together with power or high voltage cables.
The product can malfunction due to interference of noise and surge voltage from power and high
voltage cables to the signal line. Route the wires of the product separately from power or high
voltage cables.
5. Take care that actuator movement does not catch cables.
6. Operate with cables secured. Avoid bending cables at sharp angles where they enter the product.
7. Avoid twisting, folding, rotating or applying an external force to the cable.
Risk of electric shock, wire break, contact failure and lost of control for the product can happen.
8. Fix the motor cable protruding from the product in place before using.
The motor and lock cables are not robotic type cables and can be damaged when moved.Therefore
do not place it in a flexible moving tube.
9. The cable connecting the actuator and controller (LEC) is superior in bending resistance, but
should not be placed into a flexible moving tube with a radius smaller than the specified
value.
( Min. 50 mm)

10. Confirm proper wiring of the product.

Poor insulation (interference with other circuits, poor insulation between terminals and etc.) can
apply excessive voltage or current to the product causing damage.
11. The Speed / pushing force may vary, depending on the cable length, load and mounting
conditions etc..
If the cable length exceeds 5m, the speed / pushing force will be reduced by a maximum of 10% per
5m. (If cable length is 15m: Maximum 20% reduction.)
[Transportation]
Caution
1. Do not carry or swing the product by the motor or the cable

- 45 -
14. Electric actuators/Common precautions
14.1 Design and selection
Warning
1. Be sure to read the Operation Manual.
Handling or usage/operation other than that specified in the Operation Manual may lead to
breakage and operation failure of the product.
Any damage attributed to the use beyond the specifications is not guaranteed.
2. There is a possibility of dangerous sudden action by the product if sliding parts of machinery
are twisted due to external forces, etc.
In such cases, human injury may occur, such as by catching hands or feet in the machinery, or damage to the
machinery itself may occur. Design the machinery should be designed to avoid such dangers.
3. A protective cover is recommended to minimize the risk of personal injury.
If a driven object and moving parts of the product are in close proximity, personal injury may occur.
Design the system to avoid contact with the human body.
4. Securely tighten all stationary parts and connected parts so that they will not become loose.
When the product operates with high frequency or is installed where there is a lot of vibration,
ensure that all parts remain secure.
5. Consider a possible loss of power source.
Take measures to prevent injury and equipment damage even in the case of a power source failure.
6. Consider behavior of emergency stop of whole system.
Design the system so that human injury and/or damage to machinery and equipment will not be
caused, when it is stopped by a safety device for abnormal conditions such as a power outage or a
manual emergency stop of whole system.
7. Consider the action when operation is restarted after an emergency stop or abnormal stop of
whole system.
Design the system so that human injury or equipment damage will not occur upon restart of
operation of whole system.
8. Disassembly and modification prohibited
Do not modify or reconstruct (including additional machining) the product. An injury or failure can result.
9. Do not use stop signal,"EMG" of the controller and stop switch on the teaching box as the
emergency stop of system.
The stop signal, "EMG" of controller and the stop switch on the teaching box are for decelerating
and stopping the actuator.
Design the system with an emergency stop circuit which is applied relevant safety standard separately.
10. When using it for vertical application, it is necessary to build in a safety device.
The rod may fall due to the weight of work. The safety device should not interfere with normal
operation of the machine.
Caution
1. Operate within the limits of the maximum usable stroke.
The product will be damaged if it is used with the stroke which is over the maximum stroke. Refer to
the specifications of the product.
2. When the product repeatedly cycles with partial strokes, operate it at a full stroke at least
once a day or every 1000 strokes.
Otherwise, lubrication can run out.

- 46 -
3. Do not use the product in applications where excessive external force or impact force is
applied to it.
The product can be damaged. Each component that includes motor is made with accurate
tolerance. So even slightly deformed or miss-alignment of component may lead operation failure of
the product.
4. Refer to a common auto switch /matter (Best Pneumatics No 2) when an auto switch is built
in and used.
5. Return to origin cannot return while operating.
It cannot be done during positioning operation, pushing operation and pushing.
6. When conformity to UL is required, the electric actuator and controller should be used
with a UL1310 Class 2 power supply.

14.2 Mounting
Warning
1. Install and operate the product only after reading the Operation Manual carefully and
understanding its contents. Keep the manual in a safe place future reference.
2. Observe the tightening torque for screws.
Tighten the screws to the recommended torque for mounting the product.
3. Do not make any alterations to this product.
Alterations made to this product may lead to a loss of durability and damage to the product, which
can lead to human injury and damage to other equipment and machinery.
4. When using external guide, the guide axis should be parallel to the actuator axis.
There will be damage/excessive wear on the lead screw if the external guide is not parallel.
5. When an external guide is used, connect the moving parts of the product and the load in
such a way that there is no interference at any point within the stroke.
Do not scratch or dent the sliding parts of the product tube or piston rod etc., by striking or grasping
them with other objects. Components are manufactured to precise tolerances, so that even a slight
deformation may cause faulty operation.
6. Prevent the seizure of rotating parts.
Prevent the seizure of rotating parts (pins, etc.) by applying grease.
7. Do not use the product until you verify that the equipment can be operated properly.
After mounting or repair, connect the power supply to the product and perform appropriate functional
inspections to check it is mounted properly.
8. At the overhang mounted impeller fixation
There is a possibility that the power at the bending moment damages the actuator when moving it at
high speed.
The support metal fittings that suppress the vibration of the main body of the actuator are installed.
Lower and use speed for the state that the actuator doesn't vibrate.
9. When attaching work piece, do not apply strong impact or large moment.
If an external force over the allowable moment is applied, it may cause looseness in the guide unit,
an increase in sliding resistance or other problems.
10. Maintenance space.
Allow sufficient space for maintenance and inspection.

- 47 -
14.3 Handling

Warning
1. Do not touch the motor while in operation.
The surface temperature of the motor can increase to approx. 90oC to 100oC due to operating
conditions. Energizing alone may also cause this temperature increase. As it may cause burns, do
not touch the motor when in operation.
2. If abnormal heating, smoking or fire, etc., occurs in the product, immediately shut off the
power supply.
3. Immediately stop operation if abnormal operation noise or vibration occurs.
If abnormal operation noise or vibration occurs, the product may have been mounted incorrectly.
Unless operation of the product is stopped for inspection, the product can be seriously damaged.
4. Never touch the rotating part of the motor or moving part of the actuator while in operation.
5. When installing, adjusting, inspecting or performing maintenance on the product, controller and
related equipment, be sure to shut off the power supply to each of them. Then, lock it so that no one
other than the person working can turn the power on, or implement measures such as a safety plug.
6. In the case of the actuator that has a servo motor (24VDC), the “motor phase detection step"
is done by inputting the servo on signal just after the controller power is turned on. The
“motor phase detection step” operates the table/rod to the maximum distance of the lead
screw. (The motor rotates in the reverse direction if the table hits an obstacle such as the end
stop damper.) Take the “motor phase detection step” into consideration for the installation
and operation of this actuator.
Caution
1. Keep the controller and product combined as delivered for use.
The product is set in parameters for shipment. If it is combined with a different parameter, failure can result.
2. Check the product for the following points before operation.
a) Damage to electric driving line and signal lines
b) Looseness of the connector to each power line and signal line
c) Looseness of the actuator/cylinder and controller/driver mounting
d) Abnormal operation
e) Emergency stop of the total system
3. When more than one person is performing work, decide on the procedures, signals,
measures and resolution for abnormal conditions before beginning the work. Also,
designate a person to supervise work other than those performing work.
4. Actual speed of the product will be changed by the workload.
Before selecting a product, check the catalog for the instructions regarding selection and
specifications.
5. Do not apply a load, impact or resistance in addition to a transferred load during return to origin.
In the case of the return to origin by pushing force, additional force will cause displacement of the
origin position since it is based on detected motor torque.
6. Do not remove the name plate.
7. Operation test should be done by low speed. Start operation by predefined speed after
confirming there is no trouble.
[Earth]
Warning
1. Please give the earth of the actuator.
2. Please make it to the earth of the exclusive use. The earth construction is D seed.
(Below earth resistance 100Ω)
3. Please shorten the distance until the actuator and earth.

- 48 -
[Unpackaging]
Caution
1. Check the received product is as ordered.
If a different product is installed from the one ordered, injury or damage can result.

14.4. Operating environment

Warning
1. Avoid use in the following environments.
a. Locations where a large amount of dusts and cutting chips are airborne.
b. Locations where the ambient temperature is outside the range of the temperature specification
(refer to specifications).
c. Locations where the ambient humidity is outside the range of the humidity specification (refer to
specifications).
d. Locations where corrosive gas, flammable gas, sea water, water and steam are present.
e. Locations where strong magnetic or electric fields are generated.
f. Locations where direct vibration or impact is applied to the product.
g. Areas that are dusty, or are exposed to splashes of water and oil drops.
h. Areas exposed to direct sunlight (ultraviolet ray).
2. Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.
If cutting oils, coolant or oil mist contaminates the product, failure or increased sliding resistance can
result.
3. Install a protective cover when the product is used in an environment directly exposed to
foreign matters such as dust, cutting chips and spatter.
Play or increased sliding resistance can result.
4. Shade the sunlight in the place where the product is applied with direct sunshine.
5. Shield the valve from radiated heat generated by nearby heat sources.
When there is a heat source surrounding the product, the radiated heat from the heat source can
increase the temperature of the product beyond the operating temperature range. Protect it with a
cover, etc.
6. Grease oil can be decreased due to external environment and operating conditions, and it
deteriorates lubrication performance to shorten the life of the product.
[Storage]
Warning
1. Do not store the product in a place in direct contact with rain or water drops or is exposed to
harmful gas or liquid.
2. Store in an area that is shaded from direct sunlight and has a temperature and humidity
within the specified range (-10oC to 60oC and 35 to 85% No condensation or freezing.
3. Do not apply vibration and impact to the product during storage.

- 49 -
14.5 Maintenance
Warning
1. Do not disassemble or repair the product.
Fire or electric shock can result.
2. Before modifying or checking the wiring, the voltage should be checked with a tester 5
minutes after the power supply is turned off.
Electrical shock can result.
Caution
1. Maintenance should be performed according to the procedure indicated in the Operating
Manual.
Incorrect handling can cause injury, damage or malfunction of equipment and machinery.
2. Removal of product.
When equipment is serviced, first confirm that measures are in place to prevent dropping of work
pieces and run-away of equipment, etc, and then cut the power supply to the system. When
machinery is restarted, check that operation is normal with actuators in the proper positions.
[Lubrication]
Caution
1. The product has been lubricated for life at manufacturer, and does not require lubrication in
service.
Contact SMC if lubrication will be applied.

14.6 Precautions for actuator with lock

1. Do not use the lock as a safety lock or a control that requires a locking force.
The lock used for the product with a lock is designed to prevent dropping of work piece.
2. For vertical mounting, use the product with a lock.
If the product is not equipped with a lock, the product will move and drop the work piece when
the power is removed.
3. "Measures against drops” means preventing a work piece from dropping due to its
weight when the product operation is stopped and the power supply is turned off.
4. Do not apply an impact load or strong vibration while the lock is activated.
If an external impact load or strong vibration is applied to the product, the lock will lose it’s
holding force and damage to the sliding part of the lock or reduced lifetime can result. The
same situations will happen when the lock slips due to a force over the thurst of the product, as
this accelerates the wear to the lock.
5. Do not apply liquid or oil and grease to the lock or its surrounding.
When liquid or oil and grease is applied to the sliding part of the lock, its holding force will
reduce significantly.
6. Take measures against drops and check that safety is assured before mounting,
adjustment and inspection of the product.
If the lock is released with the product mounted vertically, a work piece can drop due to its weight.

- 50 -
15. Gateway unit and its peripheral devices /Specific product precautions
15.1 Design and selection
Warning
1. Be sure to apply the specified voltage.
Otherwise, a malfunction and breakage of the gateway unit may be caused.
If the applied voltage is lower than the specified, it is possible that the load cannot be moved due to
an internal voltage drop. Please check the operating voltage before use.
2. Do not operate beyond the specifications.
It may cause a fire, malfunction or actuator damage can result. Please check the specifications before
use.
3. Install an emergency stop circuit.
Please install an emergency stop outside of the enclosure so that it can stop the system operation
immediately and intercept the power supply.
4. In order to prevent danger and damage due to the breakdown and the malfunction of this
product, which may occur at a certain probability, a backup system should be established
previously by giving a multiple-layered structure or a fail-safe design to the equipment, etc.
5. If a fire or danger against the personnel is expected due to an abnormal heat generation,
ignition, smoking of the product, etc., cut off the power supply for this product and the
system immediately.
6. Use UL1310 compliant Class 2 power supply unit for direct current.
15.2 Handling
Warning
1. The inside of the gateway unit and its connector should not be touched.
It may cause an electric shock or damage to the controller.
2. Do not perform the operation or setting of this equipment with wet hands.
It may cause an electric shock.
3. Product with damage or the one lacking of any components should not be used.
It may cause an electric shock, fire, or injury.
4. Use only the specified combination between the controller and electric actuator.
It may cause damage to the controller or the actuator.
5. Be careful not to be caught or hit by the workpiece while the actuator is moving.
It may cause an injury.
6. Do not connect the power supply or power on the product before confirming the area where
the work moves is safe.
The movement of the work may cause accident.
7. Do not touch the product when it is energized and for some time after power has been
disconnected, as it is very hot.
It may lead to a burn due to the high temperature.
8. Check the voltage using a tester for more than 5 minute after power-off in case of installation,
wiring and maintenance.
There is a possibility of getting electric shock, fire and injury.

- 51 -
9. Do not use in an area where dust, powder dust, water or oil is in the air.
It will cause failure or malfunction.
10. Do not use in an area where a magnetic field is generated.
It will cause failure or malfunction.
11. Do not install in the environment of flammable gas, corrosive gas and explosive gas.
It could lead to fire, explosion and corrosion.
12. Radiant heat from strong heat supplys such as a furnace, direct sunlight, etc. should not be
applied to the product.
It will cause failure of the gateway unit or its peripheral devices.
13. Do not use the product in an environment subject to a temperature cycle.
It will cause failure of the gateway unit or its peripheral devices.
14. Do not use in a place where surges are generated.
When there are units that generate a large amount of surge around the product (e.g., solenoid type
lifters, high frequency induction furnaces, motors, etc.), this may cause deterioration or damage to
the product’s' internal circuit. Avoid supplys of surge generation and crossed lines.
15. The product is not immune to lightening strikes. Take measures against lightening strikes in
the system.
16. Do not install this product in an environment under the effect of vibrations and impacts.
It will cause failure or malfunction.
17. If this product is used with a relay or solenoid valve, they should be the surge absorbing
element built-in type.
15.3 Mounting

Warning
1. The gateway unit and its peripheral devices should be installed on a fire-proof material.
A direct installation on or near a flammable material may cause fire.
2. Do not install this product in a place subject to vibrations and impacts.
It may cause an electric shock, fire, or injury.
3. Take measure so that the operating temperature of this gateway unit and its peripheral
devices are within the range of the specifications. Also, this controller should be installed
with 50mm or larger spaces between each side of it and the other structures or components.
It may cause a malfunction of the controller and its peripheral devices and a fire.
4. Do not mount this gateway unit and its peripheral devices together with a large-sized
electromagnetic contactor or no-fuse breaker, which generates vibration, on the same panel.
Mount them on different panels, or keep the controller and its peripheral devices away from
such a vibration supply.
5. This gateway unit and its peripheral devices should be installed on a flat surface.
If the mounting surface is distorted or not flat, an unacceptable force may be added to the housing,
etc. to cause troubles.

- 52 -
15.4 Electrical wiring

1. Do not apply any excessive force to cables by repeated bending, tensioning or placing a
heavy object on the cables.
It may cause an electric shock, fire, or breaking of wire.
2. Connect wires and cables correctly.
Incorrect wiring could break he gateway unit or its peripheral devices depending on the seriousness.
3. Do not connect wires while the power is supplied.
It can break the gateway unit or its peripheral devices could be damaged to cause a malfunction.
4. Do not carry this product by holding its cables.
It may cause an injury or damage to the product.
5. Do not connect power cable or high-voltage cable in the same wiring route as the unit.
Te wires to the gateway unit or its peripheral devices can be interrupted with noise or induced surge
voltage from power lines or high-voltage lines and malfunction could be caused.
Separate the wiring of the gateway unit and its peripheral device from that of power line and high
voltage line.
6. Verify the insulation of wiring.
Insulation failure (interference with other circuit, poor insulation between terminals and etc.) could
introduce excessive voltage or current to the gateway unit or its peripheral devices and damage
them.
15.5 Power supply
Caution
1. Use a power supply that has low noise between lines and between power and ground.
In cases where noise is high, an isolation transformer should be used.
2. To prevent surges from lightning, an appropriate measure should be taken. Ground the surge
absorber for lightning separately from the grounding of the gateway unit and its peripheral
devices.

15.6. Grounding
1. Be sure to carry out grounding in order to ensure the noise tolerance of the gateway unit.
It may cause an electric shock or fire.
2. Dedicated grounding should be used.
Grounding should be to a D-class ground (Ground resistance of 100 Ω or less.)
3. Grounding should be performed near the unit as much as possible to shorten the grounding
distance.
4. In the unlikely event that malfunction is caused by the ground, it may be disconnected.

- 53 -
15.7 Maintenace
1. Perform a maintenance check periodically
Confirm wiring and screws are not loose.
Loose screws or wires may cause unintentional malfunction.
2. Conduct an appropriate functional inspection after completing the maintenance.
In case of any abnormities (in the case that the actuator does no move, etc.), stop the operation of
the system. Otherwise, an unexpected malfunction may occur and it will become impossible to
secure the safety.
3. Do not disassemble, modify or repair this gateway unit and the peripheral equipment.
4. Do not put anything conductive or flammable inside of this gateway unit.
It may cause a fire and explosion.
5. Do not conduct an insulation resistance test and withstand voltage test on this product.
6. Ensure sufficient space for maintenance activities. Provide space required for
maintenance.
Design the system that allows required space for maintenance.
7. Do not used solvents such as benzene, thinner etc. to clean the gateway unit.
They could damage the surface of the body and erase the markings on the body.
Use a soft cloth to remove stains.
For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up
the stains again with a dry cloth.

- 54 -
 Revision history
No.LEC-OM03201
Feb/2012 1st printing
No.LEC-OM03202
Mar/2012 Revision
No.LEC-OM03803
Apr/2012 Revision
Addition to notes about UL recognition

4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN

Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362

URL http://www.smcworld.com

Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.

© 2012 SMC Corporation All Rights Reserved

- 55 -