™

CYCOLOY FR RESINS C2950HF

REGION AMERICAS

DESCRIPTION
CYCOLOY C2950HF Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) resin is a high heat grade that can be injection molded. This non-chlorinated,
non-brominated flame retardant high heat PC/ABS wih enhanced processability has a UL V0 & 5VA/B flame rating. CYCOLOY C2950HF resin is an excellent
candidate for a wide variety of applications including appliances, lighting and electrical.

TYPICAL PROPERTY VALUES Revision 20191031

PROPERTIES TYPICAL VALUES UNITS TEST METHODS

MECHANICAL
Tensile Stress, yld, Type I, 50 mm/min 64 MPa ASTM D 638

Tensile Strain, yld, Type I, 50 mm/min 5 % ASTM D 638

Tensile Strain, brk, Type I, 50 mm/min 40 % ASTM D 638

Flexural Stress, yld, 2.6 mm/min, 100 mm span 96 MPa ASTM D 790

Flexural Modulus, 2.6 mm/min, 100 mm span 2580 MPa ASTM D 790
Hardness, Rockwell R 121 - ASTM D 785

IMPACT
Izod Impact, notched, 23°C 453 J/m ASTM D 256

Instrumented Impact Energy @ peak, 23°C 54 J ASTM D 3763

THERMAL
Vicat Softening Temp, Rate B/50 112 °C ASTM D 1525
HDT, 1.82 MPa, 3.2mm, unannealed 87 °C ASTM D 648

HDT, 0.45 MPa, 6.4 mm, unannealed 101 °C ASTM D 648

HDT, 1.82 MPa, 6.4 mm, unannealed 95 °C ASTM D 648

CTE, -30°C to 30°C, flow 7.2E-05 1/°C ASTM D 696

CTE, -30°C to 30°C, xflow 7.2E-05 1/°C ASTM D 696

Thermal Conductivity 0.2 W/m-°C ASTM C177

Relative Temp Index, Elec 85 °C UL 746B

Relative Temp Index, Mech w/impact 85 °C UL 746B

Relative Temp Index, Mech w/o impact 85 °C UL 746B

PHYSICAL
Specific Gravity 1.18 - ASTM D 792
Water Absorption, 24 hours 0.1 % ASTM D 570

Water Absorption, equilibrium, 23C 0.4 % ASTM D 570

Mold Shrinkage, flow, 3.2 mm 0.4 – 0.6 % SABIC method

Mold Shrinkage, xflow, 3.2 mm 0.4 – 0.6 % SABIC method

Melt Flow Rate, 260°C/2.16 kgf 22 g/10 min ASTM D 1238

ELECTRICAL
Volume Resistivity 1.6E+17 Ohm-cm ASTM D 257

Surface Resistivity >1.E+16 Ohm ASTM D 257

Dielectric Strength, in oil, 3.2 mm 24.3 kV/mm ASTM D 149

Relative Permittivity, 50/60 Hz 2.8 - ASTM D 150

Relative Permittivity, 1 MHz 2.7 - ASTM D 150

Dissipation Factor, 50/60 Hz 0.0052 - ASTM D 150

© 2019 Copyright by SABIC. All rights reserved
Dissipation Factor, 1 MHz 0.0071 - ASTM D 150

Arc Resistance, Tungsten {PLC} 6 PLC Code ASTM D 495

Hot Wire Ignition {PLC) 2 PLC Code UL 746A

High Voltage Arc Track Rate {PLC} 3 PLC Code UL 746A

High Ampere Arc Ign, surface {PLC} 0 PLC Code UL 746A

 PHYSICAL
Specific Gravity 1.18 - ASTM D 792
Water Absorption, 24 hours 0.1 % ASTM D 570

Water Absorption, equilibrium, 23C 0.4 % ASTM D 570

Mold Shrinkage, flow, 3.2 mm 0.4 – 0.6 % SABIC method

Mold Shrinkage, xflow, 3.2 mm 0.4 – 0.6 % SABIC method

Melt Flow Rate, 260°C/2.16 kgf 22 g/10 min ASTM D 1238

ELECTRICAL
Volume Resistivity 1.6E+17 Ohm-cm ASTM D 257

Surface Resistivity >1.E+16 Ohm ASTM D 257

Dielectric Strength, in oil, 3.2 mm 24.3 kV/mm ASTM D 149

Relative Permittivity, 50/60 Hz 2.8 - ASTM D 150

PROPERTIES TYPICAL VALUES UNITS TEST METHODS
Relative Permittivity, 1 MHz 2.7 - ASTM D 150

Dissipation Factor, 50/60 Hz 0.0052 - ASTM D 150

Dissipation Factor, 1 MHz 0.0071 - ASTM D 150

Arc Resistance, Tungsten {PLC} 6 PLC Code ASTM D 495

Hot Wire Ignition {PLC) 2 PLC Code UL 746A

High Voltage Arc Track Rate {PLC} 3 PLC Code UL 746A

High Ampere Arc Ign, surface {PLC} 0 PLC Code UL 746A

Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A

FLAME CHARACTERISTICS

UL Yellow Card Link E121562-221035 - -

UL Recognized, 94V-2 Flame Class Rating 0.76 mm UL 94

UL Recognized, 94V-0 Flame Class Rating 1.49 mm UL 94

UL Recognized, 94-5VA Flame Class Rating 3.4 mm UL 94

UL Recognized, 94-5VB Flame Class Rating 2.48 mm UL 94

Oxygen Index (LOI) 30 % ASTM D 2863

INJECTION MOLDING
Drying Temperature 80 – 90 °C

Drying Time 3–4 hrs

Drying Time (Cumulative) 8 hrs
Maximum Moisture Content 0.04 %

Melt Temperature 245 – 275 °C

Nozzle Temperature 245 – 275 °C

Front - Zone 3 Temperature 245 – 275 °C

Middle - Zone 2 Temperature 220 – 265 °C
Rear - Zone 1 Temperature 220 – 255 °C

Mold Temperature 60 – 80 °C

Back Pressure 0.3 – 0.7 MPa

Screw Speed 40 – 70 rpm

Shot to Cylinder Size 30 – 80 %

Vent Depth 0.038 – 0.076 mm

DISCLAIMER
Any sale by SABIC, its subsidiaries and affiliates (each a “seller”), is made exclusively under seller’s standard conditions of sale (available upon request) unless agreed
otherwise in writing and signed on behalf of the seller. While the information contained herein is given in good faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE
PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each customer must determine the suitability of seller
materials for the customer’s particular use through appropriate testing and analysis. No statement by seller concerning a possible use of any product, service or design is
intended, or should be construed, to grant any license under any patent or other intellectual property right.

© 2019 Copyright by SABIC. All rights reserved