M190PW01-V5 Auo

Product Specification M190PW01 V5
AU OPTRONICS CORPORATION
( V ) Preliminary Specification
( ) Final Specification
Module 19” WXGA+ Color TFT-LCD
Model Name M190PW01 V5
Checked &
Customer Date Date
Approved by
Arthur Chung
www.DataSheet.co.kr
2/3/09
Approved by Prepared by Date
AlanCHLiu 2/3/09
Note: This Specification is subject to change without Desktop Display Business Group /
notice. AU Optronics corporation
document version 0.2 1/28
Datasheet pdf - http://www.DataSheet4U.net/

Contents
1. Handling Precautions.............................................................................................................. 4
2. General Description ................................................................................................................ 5
2.1 Display Characteristics ....................................................................................................................... 5
3. Functional Block Diagram .................................................................................................... 10
4. Absolute Maximum Ratings.................................................................................................. 11
4.1 Absolute Ratings of TFT LCD Module............................................................................................. 11
4.2 Absolute Ratings of Backlight Unit .................................................................................................. 11
4.3 Absolute Ratings of Environment ..................................................................................................... 12
5. Electrical characteristics ...................................................................................................... 13
5.1 TFT LCD Module ............................................................................................................................. 13
5.2 Backlight Unit ................................................................................................................................... 15
6. Signal Characteristic............................................................................................................. 16
6.1 Pixel Format Image........................................................................................................................... 16
6.2 The Input Data Format ...................................................................................................................... 17
6.4 Interface Timing ................................................................................................................................ 20
6.5 Power ON/OFF Sequence................................................................................................................. 22
www.DataSheet.co.kr
7. Connector & Pin Assignment ............................................................................................... 23

7.1 TFT LCD Module ............................................................................................................................. 23
7.2 Backlight Unit ................................................................................................................................... 24
8. Reliability Test ....................................................................................................................... 25
9. Shipping Label....................................................................................................................... 26
10. Mechanical Characteristics ................................................................................................ 26

Record of Revision
Version and Date Page Old description New Description Remark
0.1 2009/1/12 all First edition for all customer N/A V0.1
0.2 2009/2/03 5 V0.2
White x : Min:0.617, Typ:0.647, Max:0.677 White x : Min:0.283, Typ:0.313, Max:0.343 V0.2

6
White y:Min: 0.308, Typ: 0.338, Max: 0.368 White y : Min:0.299, Typ:0.329, Max:0.359
20 T6:Max 100 T6 :Max - V0.2
www.DataSheet.co.kr

1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CCFL reflector edge. Instead, press at the far
ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
www.DataSheet.co.kr
ordinances or regulations for disposal.

13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.

2. General Description
This specification applies to the 19 inch-wide Color TFT-LCD Module M190PW01.
The display supports the WXGA+ (1440(H) x 900(V)) screen format and 16.7M colors. All input signals are 2 Channel
LVDS interface compatible.
This module does not contain an inverter card for backlight.
.
2.1 Display Characteristics

The following items are characteristics summary on the table under 25 ℃ condition:
Items Unit Specifications

Active Area [mm] 408.24 (H) x 255.15(V)
Pixels H x V 1440x3(RGB) x 900
Pixel Pitch [mm] 0.2835x 0.2835
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode,Normally White
White Luminance [cd/m ] 300 cd/m2 @ 7.5mA (Typ)
2
Contrast Ratio 1000:1

Optical ResponseTime [msec] 5 (Typ, on/off)
Nominal Input Voltage VDD [Volt] www.DataSheet.co.kr +5.0 (Typ)
Power Consumption
[Watt] 15.5 (Typ)
(VDD line + CCFL line)
Weight [Grams] 2250 (Typ)
Physical Size (H x V x D) [mm] 428.0(W) x 278.0(H) x 16.5(D) (Typ)

Electrical Interface Dual Channel LVDS
Surface Treatment Anti-glare type, Hardness 3H
Support Colors 16.7M colors (RGB 6-bits+HiFRC)
Temperature Range
Operating [oC] 0 to +50
Storage (Shipping) [ C] -20 to +60
o
RoHS Compliance RoHS Compliance

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note

Horizontal (Right) 70 85
-
CR = 10 (Left) 70 85
Vertical (Up) 70 80
-
CR = 10 (Down) 70 80
Viewing Angle [degree] 1
Horizontal (Right) 75 85
--
CR = 5 (Left) 75 85
Vertical (Right) 75 85
--
CR = 5 (Left) 75 85
Luminance Uniformity [%] 9 Points 75 80 - 2, 3
Rising - 3.6 5.7
Optical Response Time [msec] Falling - 1.4 2.3 4, 6
Rising + Falling - 5 8
Red x 0.617 0.647 0.677
Red y 0.308 0.338 0.368
Green x www.DataSheet.co.kr
0.260 0.290 0.320

Color / Chromaticity Green y 0.564 0.594 0.624
Coordinates 4
(CIE 1931) Blue x 0.115 0.145 0.175
Blue y 0.037 0.067 0.097
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359
White Luminance
[cd/m2 ] 250 300 - 4
(At CCFL= 7.5mA)
Contrast Ratio 600 1000 - 4
Cross Talk (At 75Hz) [%] - - 1.5 5
Flicker [dB] - - -20 7
Optical Equipment: BM-5A, BM-7, PR880, or equivalent

Note 1: Definition of viewing angle

Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal
and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as
follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The
measurement direction is typically perpendicular to the display surface with the screen rotated about its
center to develop the desired measurement viewing angle.
Note 2: 9 points position

www.DataSheet.co.kr
90 % 50 % 10 %
10 %
50 %
90 %
Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance
Minimum Luminance of 9 points
δW9 =
Maximum Luminance of 9 points

Note 4: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
Photo detector
Field=2°
50 cm
LCD Panel TFT-LCD Module

www.DataSheet.co.kr
Center of the screen
Note 5: Definition of Cross Talk (CT)

CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 6: Definition of response time:

The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black ”(falling time), respectively. The response time
is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.
Note 7: Subchecker Pattern
RGB RGB
Gray Level = L127 www.DataSheet.co.kr
RGB RGB
Gray Level = L0
RGB RGB
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
AC
DC
Time
AC Level(at 30 Hz)
Flicker (dB) = 20 log
DC Level

3. Functional Block Diagram

The following diagram shows the functional block of the 19.0 inches wide Color TFT-LCD Module:
AUO ASIC G1
LVDS Timing TFT-LCD
Y-Driver IC
LVDS Receiver Controller 1440*(3)*900
Pixels
Connector
+5V
X-Driver IC
G900
D1 D4320
2 CCFL
Gamma
DC/DC
Correction
Converter
www.DataSheet.co.kr
I/F + X-PCB DC POWER

Inverter
I/F PCB Interface: YEON HO 35001HS-02L

FI-XB30SSL-HF15(JAE)/MSBKT2407P30HB(信盛
信盛)
信盛 Mating Type: 35001WR-02LP
Mating Type:
FI-X30HL-T(JAE)(Locked Type)

4. Absolute Maximum Ratings

Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions

Logic/LCD Drive
VDD -0.3 +5.5 [Volt] Note 1, 2
Voltage
4.2 Absolute Ratings of Backlight Unit

CCFL Current ICFL - 8 [mA] rms Note 1, 2
www.DataSheet.co.kr

4.3 Absolute Ratings of Environment

Operating Temperature TOP 0 +50 [oC]
Operation Humidity HOP 5 90 [%RH]
Note 3
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST 5 90 [%RH]
Note 1: With in Ta= 25℃

Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
www.DataSheet.co.kr
Operating Range Storage Range

5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition

Logic/LCD Drive
VDD 4.5 5.0 5.5 [Volt]
Voltage
VDD= 5.0V, All Black Pattern
IDD Input Current - 0.9 1.1 [A]
At 60Hz
VDD= 5.0V, All Black Pattern
PDD VDD Power - 4.5 5.5 [Watt]
At 60Hz , Note 1
IRush Inrush Current - - 3 [A] Note 2
Allowable logic/LCD [mV] VDD=5.0, All black pattern at
VDDrp Drive Ripple Voltage 200
p-p 60Hz
Note 1: The variance of VDD power consumption is ±10%.
Note 2: Measurement conditions:
+5.0V Q3
AO6402
D6 F1
D5
www.DataSheet.co.kr
D2 S
VCC
D1
R1 (LCD Module Input)

47K
G
C1
1uF/16V
(High to Low)
Control
D1
D2
D5
D6
Signal Q3
R2 AO6402
G
1K
S
C3
+12.0V
2
SW1
SW MAG-SPST VR1 0.01uF/25V
47K
1
C2
1uF/25V
90% 5.0V
10%
VDD rising time 0V
0.5ms

5.1.2 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
Each signal characteristics are as follows;
Symbol Parameter Min Typ Max Units Condition

Differential Input
VTH - - 100 [mV] VICM = 1.2V Note
High Threshold
Differential Input
VTL -100 - - [mV] VICM = 1.2V Note
Low Threshold
Input Differential
100 400 600 [mV] Note
Voltage
│VID│
Differential Input
VICM Common Mode 1.0 1.2 1.5 [V] VTH/VTL = ± 100mV Note
Voltage
Note: LVDS Signal Waveform
V
T │VID│
H
www.DataSheet.co.kr
VICM
VSS

5.2 Backlight Unit

Parameter guideline for CCFL Inverter is under stable conditions at 25℃ (Room Temperature):
Parameter Min. Typ. Max. Unit Condition

CCFL Standard Current(ISCFL) 7.0 7.5 8.0 [mA] rms Note 2
CCFL Operation Current(IRCFL) 3.0 7.5 8.0 [mA] rms Note 2
CCFL Frequency(FCFL) 40 50 80 [KHz] Note 3,4
CCFL Ignition Voltage(ViCFL, Ta= 0℃) 1650 - - [Volt] rms

Note 5
CCFL Ignition Voltage(ViCF, Ta= 25℃) 1250 - - [Volt] rms
700
CCFL Operation Voltage (VCFL) - 850 [Volt] rms Note 6
(@7.5mA)
CCFL Power Consumption(PCFL) - 11 12.1 [Watt] Note 6
CCFL Life Time(LTCFL) 40,000 50,000 - [Hour] Note 7
Note 1: Typ. are AUO recommended design points.

*1 All of characteristics listed are measured under the condition using the AUO test inverter.
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.
www.DataSheet.co.kr
Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker
at low power may happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of
CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is
recommended to keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL
discharge frequency. So all the parameters of an inverter should be carefully designed so as not
to produce too much leakage current from high-voltage output of the inverter.
Note 2: It should be employed the inverter which has “Duty Dimming”, if IRCFL is less than 3mA.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter
and TFT LCD.
Note 4: The frequency range will not affect to lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,650
voltage. Lamp units need 1,650 voltage minimum for ignition.
Note 6: The variance of CCFL power consumption is ±10%. Calculator value for reference (ISCFL × VCFL ×
2 = PCFL)
Note 7: Definition of life: brightness becomes 50%. The typical life time of CCFL is under the condition at
7.5 mA lamp current.

6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
1 2 1439 1440
1st Line R G B R G B R GB R G B
900 Line R G B R G B R GB R G B
www.DataSheet.co.kr

6.2 The Input Data Format
Note1: Normally, DE, VS, HS on EVEN channel are not used.

www.DataSheet.co.kr
Note2: 8-bits signal input.

6.3 Signal Description

The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels
while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
7 GND Power Ground
8 RxOCLKIN- Negative LVDS differential clock input (Odd clock)
9 RxOCLKIN+ Positive LVDS differential clock input (Odd clock)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
www.DataSheet.co.kr
14 GND Power Ground

17 GND Power Ground
20 RxECLKIN- Negative LVDS differential clock input (Even clock)
21 RxECLKIN+ Positive LVDS differential clock input (Even clock)
24 GND Power Ground
25 NC No contact (For AUO test only)
28 VCC +5.0V Power Supply

Note1: Start from left side
Connector
1 30
RxOIN0-
VCC
www.DataSheet.co.kr
Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow PSWG.

6.4 Interface Timing
6.4.1 Timing Characteristics
Signal Item Symbol Min Typ Max Unit

Period Tv 910 916 2047 Th
Vertical
Active Tdisp(v) 900 900 900 Th
Section
Blanking Tbp(v)+Tfp(v)+PWvs 10 16 1147 Th
Period Th 870 964 2047 Tclk
Horizontal
Active Tdisp(h) 720 720 720 Tclk
Section
Blanking Tbp(h)+Tfp(h)+PWhs 150 244 1327 Tclk
Period Tclk 22.2 21.1 15.4 ns
Clock
Frequency Freq 45 54 67.5 MHz
Frame rate Frame rate F 55 60 76 Hz
Note : DE mode only
www.DataSheet.co.kr

21/28
M190PW01 V5
Tv
Vsync
PWvs
Hsync
Product Specification
Tfp(v) Tbp(v) Tdisp(v) Th

DE
N 1 2 3 4 N
Invalid Data Invalid Data
RGB Data
www.DataSheet.co.kr
Line Line Line Line Line Line
CLK
Tclk
Hsync
PWhs
Tbp(h) Tfp(h)
DE
Tdisp(h)
6.4.2 Timing Diagrams RGB Data Invalid Data
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data
(Odd) 1 3 5 7 9 11 M-5 M-3 M-1
document version 0.2

RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
(Even) Invalid Data Invalid Data
2 4 6 8 10 12 M-4 M-2 M
6.5 Power ON/OFF Sequence

VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off.
www.DataSheet.co.kr
Power Sequence Timing
Value
Parameter Unit
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 40 50 [ms]
T3 200 - - [ms]
T4 200 - - [ms]
T5 0.5 16 50 [ms]
T6 - - - [ms]
T7 1000 - - [ms]

7. Connector & Pin Assignment

Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module

7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card
Manufacturer JAE or STM(信盛)
FI-XB30SSL-HF15
Type Part Number
MSBKT2407P30HB
FI-X30HL-T ( Locked Type )

Mating Housing Part Number
FI-X30S-H ( Unlocked Type ) or equivalent
7.1.2 Pin Assignment www.DataSheet.co.kr
Pin# Signal Name Pin# Signal Name

1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 GND 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 GND
15 RxEIN1- 16 RxEIN1+
17 GND 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 GND
25 NC 26 NC
27 NC 28 VCC
29 VCC 30 VCC

7.2 Backlight Unit

Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
Connector Name / Designation Lamp Connector / Backlight lamp
Manufacturer YEON HO
Type Part Number 35001HS-02L
Mating Type Part Number 35001WR-02LP or equivalent
7.2.1 Signal for Lamp connector
Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage (Lamp 1)
Upper CN1
2 Cold1 White Low Voltage (Lamp 1)
www.DataSheet.co.kr
Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage (Lamp 2)
Lower CN2
2 Cold1 White Low Voltage (Lamp 2)

8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition Note

Temperature Humidity Bias (THB) Ta= 50℃, 80%RH, 300hours
High Temperature Operation (HTO) Ta= 50℃, 50%RH, 300hours
Low Temperature Operation (LTO) Ta= 0℃, 300hours
High Temperature Storage (HTS) Ta= 60℃, 300hours
Low Temperature Storage (LTS) Ta= -20℃, 300hours
Acceleration: 1.5 G
Vibration Test Wave: Random
(Non-operation) Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Drop Test Height: 60 cm, package test

Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles 1
On/Off Test On/10sec, Off/10sec, 30,000 cycles
www.DataSheet.co.kr
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,

8 points, 25 times/ point.
ESD (Electro Static Discharge) 2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.
Operation:10,000 ft
Altitude Test
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20℃ to 60℃, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.

9. Shipping Label
The shipping label format is shown as below.
www.DataSheet.co.kr

10. Mechanical Characteristics
www.DataSheet.co.kr

www.DataSheet.co.kr

M190PW01-V5 Auo

Uploaded by

Copyright:

Available Formats

M190PW01-V5 Auo

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

M190PW01-V5 Auo

Uploaded by

Copyright:

Available Formats

Product Specification M190PW01 V5

Module 19” WXGA+ Color TFT-LCD

Model Name M190PW01 V5

Approved by Prepared by Date

document version 0.2 1/28

Datasheet pdf - http://www.DataSheet4U.net/

7. Connector & Pin Assignment ............................................................................................... 23

document version 0.2 2/28

Datasheet pdf - http://www.DataSheet4U.net/

0.2 2009/2/03 5 V0.2

White x : Min:0.617, Typ:0.647, Max:0.677 White x : Min:0.283, Typ:0.313, Max:0.343 V0.2

20 T6:Max 100 T6 :Max - V0.2

document version 0.2 3/28

Datasheet pdf - http://www.DataSheet4U.net/

ordinances or regulations for disposal.

document version 0.2 4/28

Datasheet pdf - http://www.DataSheet4U.net/

2.1 Display Characteristics

Items Unit Specifications

Contrast Ratio 1000:1

Weight [Grams] 2250 (Typ)

Physical Size (H x V x D) [mm] 428.0(W) x 278.0(H) x 16.5(D) (Typ)

RoHS Compliance RoHS Compliance

document version 0.2 5/28

Datasheet pdf - http://www.DataSheet4U.net/

2.2 Optical Characteristics

Item Unit Conditions Min. Typ. Max. Note

0.260 0.290 0.320

Optical Equipment: BM-5A, BM-7, PR880, or equivalent

document version 0.2 6/28

Datasheet pdf - http://www.DataSheet4U.net/

Note 1: Definition of viewing angle

Note 2: 9 points position

document version 0.2 7/28

Datasheet pdf - http://www.DataSheet4U.net/

Note 4: Measurement method

LCD Panel TFT-LCD Module

Center of the screen

Note 5: Definition of Cross Talk (CT)

YA = Luminance of measured location without gray level 0 pattern (cd/m2)

document version 0.2 8/28

Datasheet pdf - http://www.DataSheet4U.net/

Note 6: Definition of response time:

Note 7: Subchecker Pattern

Method: Record dBV & DC value with (WESTAR)TRD-100

document version 0.2 9/28

Datasheet pdf - http://www.DataSheet4U.net/

3. Functional Block Diagram

LVDS Timing TFT-LCD

I/F + X-PCB DC POWER

I/F PCB Interface: YEON HO 35001HS-02L

document version 0.2 10/28

Datasheet pdf - http://www.DataSheet4U.net/

4. Absolute Maximum Ratings

Item Symbol Min. Max. Unit Conditions

4.2 Absolute Ratings of Backlight Unit

Item Symbol Min. Max. Unit Conditions

document version 0.2 11/28

Datasheet pdf - http://www.DataSheet4U.net/