Scribd
Upload
273 views2 pages

Structural Mechanics-I-5

Uploaded by

kabirdhivar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
273 views2 pages

Structural Mechanics-I-5

Uploaded by

kabirdhivar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DR.

BABASAHEB AMBEDKAR TECHNOLOGICAL UNIVERSITY, LONERE


Supplementary Winter Examination – 2023
Course: B. Tech. Branch: Civil Engineering Semester: IV
Subject Code & Name: Structural Mechanics -I (BTCVC 403)
Max Marks: 60 Date: 20/01/2024 Duration: 3 Hrs.
Instructions to the Students:
1. All the questions are compulsory.
2. The level of question/expected answer as per OBE or the Course Outcome (CO) on
which the question is based is mentioned in ( ) in front of the question.
3. Use of non-programmable scientific calculators is allowed.
4. Assume suitable data wherever necessary and mention it clearly.
(Level/CO) Marks
Q. 1 Solve Any Two of the following. 12
A) Derive the differential equation for Slope and Deflection. CO-1 6

B) A wooden beam 140 mm wide and 240 mm deep has a span of 4 m. CO-1 6
Determine the load, that can be placed at center to cause deflection of 10
mm. Take E as 6 GPa.
C) A Horizontal girder having uniform cross section is 14 m long and is simply CO-1 6
supported at its end. It carries two concentrated loads as shown in fig. no. 1
Calculate the deflection of the beams under the loads C and D. Take E = 200
GPa and I = 160 x 106 mm4.

Fig. No. 1

Q.2 Solve Any Two of the following. 12


A) State and explain the Maxwell’s reciprocal Theorem. CO-2 6
B) Using energy theorem, find the deflection at free end of cantilever beam of CO-2 6
span l carries a point load at the free end and mid span.
C) A rolled steel joist ISMB 250 x 125 mm as shown in fig. carries a single CO-2 6
concentrated load of 20 kN at the right third point over a simply supported
span of 9 m. if the values of Ixx for the beam is 51.316 x 106 mm4 and the
values of E for the material is 200 GPa, Calculate by the use of conjugate
beam method Deflection under the load

Q. 3 Solve Any Two of the following. 12


A) Define determinacy and indeterminacy of structures. Explain in detail with CO-3 6
examples
B) Calculate the support moment and draw BMD and SFD for a beam as CO-3 6
shown in figure no 6 by using three moment theorem.
C) A fixed beam of span ‘L’ subjected to an external clockwise moment ‘M’ at CO-3 6
a distance ‘a’ from one of its fixed supports and at a distance ‘b’ from other
end fixed support. Determine the end moments developed.
Q.4 Solve Any Two of the following. 12
A) Explain the following terms CO-4 6
i) Carry Over Factor
ii) Distribution factor
iii) Stiffness Factor.
B) Analyze the frame shown fig. no. 3 for moments at the ends of members. CO-4 6
Draw BMD. EI is same for all the members. Use Moment distribution
method.

Fig. No. 3

C) Calculate support moments by moment distribution method for given CO-4 6


continuous as shown in fig.

Fig. No. 4

Q. 5 Solve Any Two of the following. 12


A) State the assumptions made in slope and deflection method for determining CO-5 6
the support moments.
B) A continuous beam ABC is fixed at A and simply supported at B and C. The CO-5 6
Span AB of 6 m and carries a UDL of 100 kN/m. The span BC is 4m carries
a UDL of 300 kN/m . Determine the support moments.
C) Explain the procedure for analyzing a statical indeterminate structure using CO-5 6
slope and deflection method.
*** End ***

You might also like